mirror of
https://git.code.sf.net/p/openocd/code
synced 2024-11-14 18:37:11 +00:00
e6505b0489
For historical reasons, no license information was added to the
tcl files. This makes trivial adding the SPDX tag through script:
fgrep -rL SPDX tcl/ target| while read a;do \
sed -i '1{i# SPDX-License-Identifier: GPL-2.0-or-later\n
}' $a;done
With no specific license information from the author, let's extend
the OpenOCD project license GPL-2.0-or-later to the files.
Change-Id: I7b2610300b24cccd07bfa6fb5f1266970d5d3a1b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7027
Tested-by: jenkins
103 lines
3.1 KiB
INI
103 lines
3.1 KiB
INI
# SPDX-License-Identifier: GPL-2.0-or-later
|
|
|
|
# STMicroelectronics STM32MP13x (Single Cortex-A7)
|
|
# http://www.st.com/stm32mp1
|
|
|
|
# HLA does not support custom CSW nor AP other than 0
|
|
if { [using_hla] } {
|
|
echo "ERROR: HLA transport cannot work with this target."
|
|
echo "ERROR: To use STLink switch to DAP mode, as in \"board/stm32mp13x_dk.cfg\"."
|
|
shutdown
|
|
}
|
|
|
|
source [find target/swj-dp.tcl]
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME stm32mp13x
|
|
}
|
|
|
|
if { [info exists CPUTAPID] } {
|
|
set _CPUTAPID $CPUTAPID
|
|
} else {
|
|
if { [using_jtag] } {
|
|
set _CPUTAPID 0x6ba00477
|
|
} else {
|
|
set _CPUTAPID 0x6ba02477
|
|
}
|
|
}
|
|
|
|
# Chip Level TAP Controller, only in jtag mode
|
|
if { [info exists CLCTAPID] } {
|
|
set _CLCTAPID $CLCTAPID
|
|
} else {
|
|
set _CLCTAPID 0x06501041
|
|
}
|
|
|
|
swj_newdap $_CHIPNAME tap -expected-id $_CPUTAPID -irlen 4
|
|
if { [using_jtag] } {
|
|
jtag newtap $_CHIPNAME.clc tap -expected-id $_CLCTAPID -irlen 5
|
|
}
|
|
|
|
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.tap -ignore-syspwrupack
|
|
|
|
# NOTE: keep ap-num and dbgbase to speed-up examine after reset
|
|
# NOTE: do not change the order of target create
|
|
target create $_CHIPNAME.ap1 mem_ap -dap $_CHIPNAME.dap -ap-num 1
|
|
target create $_CHIPNAME.axi mem_ap -dap $_CHIPNAME.dap -ap-num 0
|
|
target create $_CHIPNAME.cpu cortex_a -dap $_CHIPNAME.dap -ap-num 1 -coreid 0 -dbgbase 0xE00D0000
|
|
|
|
$_CHIPNAME.cpu cortex_a maskisr on
|
|
$_CHIPNAME.cpu cortex_a dacrfixup on
|
|
|
|
# interface does not work while srst is asserted
|
|
# this is target specific, valid for every board
|
|
# srst resets the debug unit, behavior equivalent to "srst_pulls_trst"
|
|
reset_config srst_gates_jtag srst_pulls_trst
|
|
|
|
adapter speed 5000
|
|
adapter srst pulse_width 200
|
|
# bootrom has an internal timeout of 1 second for detecting the boot flash.
|
|
# wait at least 1 second to guarantee we are out of bootrom
|
|
adapter srst delay 1100
|
|
|
|
add_help_text axi_secure "Set secure mode for following AXI accesses"
|
|
proc axi_secure {} {
|
|
$::_CHIPNAME.dap apsel 0
|
|
$::_CHIPNAME.dap apcsw 0x10006000
|
|
}
|
|
|
|
add_help_text axi_nsecure "Set non-secure mode for following AXI accesses"
|
|
proc axi_nsecure {} {
|
|
$::_CHIPNAME.dap apsel 0
|
|
$::_CHIPNAME.dap apcsw 0x30006000
|
|
}
|
|
|
|
axi_secure
|
|
|
|
proc dbgmcu_enable_debug {} {
|
|
# keep clock enabled in low-power
|
|
## catch {$::_CHIPNAME.ap1 mww 0xe0081004 0x00000004}
|
|
# freeze watchdog 1 and 2 on core halted
|
|
catch {$::_CHIPNAME.ap1 mww 0xe008102c 0x00000004}
|
|
catch {$::_CHIPNAME.ap1 mww 0xe008104c 0x00000008}
|
|
}
|
|
|
|
proc toggle_cpu_dbg_claim0 {} {
|
|
# toggle CPU0 DBG_CLAIM[0]
|
|
$::_CHIPNAME.ap1 mww 0xe00d0fa0 1
|
|
$::_CHIPNAME.ap1 mww 0xe00d0fa4 1
|
|
}
|
|
|
|
# FIXME: most of handlers below will be removed once reset framework get merged
|
|
$_CHIPNAME.ap1 configure -event reset-deassert-pre {
|
|
adapter deassert srst deassert trst
|
|
catch {dap init}
|
|
catch {$::_CHIPNAME.dap apid 1}
|
|
}
|
|
$_CHIPNAME.cpu configure -event reset-deassert-pre {$::_CHIPNAME.cpu arp_examine}
|
|
$_CHIPNAME.cpu configure -event reset-deassert-post {toggle_cpu_dbg_claim0; dbgmcu_enable_debug}
|
|
$_CHIPNAME.ap1 configure -event examine-start {dap init}
|
|
$_CHIPNAME.ap1 configure -event examine-end {dbgmcu_enable_debug}
|