mirror of
https://git.code.sf.net/p/openocd/code
synced 2024-11-14 18:37:11 +00:00
e6505b0489
For historical reasons, no license information was added to the
tcl files. This makes trivial adding the SPDX tag through script:
fgrep -rL SPDX tcl/ target| while read a;do \
sed -i '1{i# SPDX-License-Identifier: GPL-2.0-or-later\n
}' $a;done
With no specific license information from the author, let's extend
the OpenOCD project license GPL-2.0-or-later to the files.
Change-Id: I7b2610300b24cccd07bfa6fb5f1266970d5d3a1b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7027
Tested-by: jenkins
84 lines
3.4 KiB
INI
84 lines
3.4 KiB
INI
# SPDX-License-Identifier: GPL-2.0-or-later
|
|
|
|
# NXP LPC8Nxx NHS31xx Cortex-M0+ with 8kB SRAM
|
|
# Copyright (C) 2018 by Jean-Christian de Rivaz
|
|
# Based on NXP proposal https://community.nxp.com/message/1011149
|
|
# Many thanks to Dries Moors from NXP support.
|
|
# SWD only transport
|
|
|
|
source [find target/swj-dp.tcl]
|
|
source [find mem_helper.tcl]
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME lpc8nxx
|
|
}
|
|
|
|
swj_newdap $_CHIPNAME cpu -irlen 4 -expected-id 0
|
|
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
target create $_TARGETNAME cortex_m -endian little -dap $_CHIPNAME.dap
|
|
if {![using_hla]} {
|
|
# If srst is not fitted use SYSRESETREQ to perform a soft reset
|
|
cortex_m reset_config sysresetreq
|
|
}
|
|
adapter srst delay 100
|
|
|
|
$_TARGETNAME configure -work-area-phys 0x10000000 -work-area-size 0x1ff0 -work-area-backup 0
|
|
|
|
flash bank $_CHIPNAME.flash lpc2000 0x0 0x7800 0 0 $_TARGETNAME lpc800 500
|
|
|
|
echo "*********************************************************************************"
|
|
echo "* !!!!! IMPORTANT NOTICE FOR LPC8Nxx and NHS31xx CHIPS !!!!!"
|
|
echo "* When this IC is in power-off or peep power down mode, the SWD HW block is also"
|
|
echo "* unpowered. These modes can be entered by firmware. The default firmware image"
|
|
echo "* (flashed in production) makes use of this. Best is to avoid these power modes"
|
|
echo "* during development, and only later add them when the functionality is complete."
|
|
echo "* Hardware reset or NFC field are the only ways to connect in case the SWD is"
|
|
echo "* powered off. OpenOCD can do a hardware reset if you wire the adapter SRST"
|
|
echo "* signal to the chip RESETN pin and add the following in your configuration:"
|
|
echo "* reset_config srst_only; flash init; catch init; reset"
|
|
echo "* But if the actual firmware immediately set the power down mode after reset,"
|
|
echo "* OpenOCD might be not fast enough to halt the CPU before the SWD lost power. In"
|
|
echo "* that case the only solution is to apply a NFC field to keep the SWD powered."
|
|
echo "*********************************************************************************"
|
|
|
|
# Using soft-reset 'reset_config none' is strongly discouraged.
|
|
# RESETN sets the system clock to 500 kHz. Unlike soft-reset does not.
|
|
# Set the system clock to 500 kHz before reset to simulate the functionality of hw reset.
|
|
#
|
|
proc set_sysclk_500khz {} {
|
|
set SYSCLKCTRL 0x40048020
|
|
set SYSCLKUEN 0x40048024
|
|
mww $SYSCLKUEN 0
|
|
mmw $SYSCLKCTRL 0x8 0xe
|
|
mww $SYSCLKUEN 1
|
|
echo "Notice: sysclock set to 500kHz."
|
|
}
|
|
|
|
# Do not remap the ARM interrupt vectors to anything but the beginning of the flash.
|
|
# Table System memory remap register (SYSMEMREMAP, address 0x4004 8000) bit description
|
|
# Bit Symbol Value Description
|
|
# 0 map - interrupt vector remap. 0 after boot.
|
|
# 0 interrupt vector reside in Flash
|
|
# 1 interrupt vector reside in SRAM
|
|
# 5:1 offset - system memory remap offset. 00000b after boot.
|
|
# 00000b interrupt vectors in flash or remapped to SRAM but no offset
|
|
# 00001b -
|
|
# 00111b interrupt vectors offset in flash or SRAM to 1K word segment
|
|
# 01000b -
|
|
# 11111b interrupt vectors offset in flash to 1K word segment 8 to 31
|
|
# 31:6 reserved
|
|
#
|
|
proc set_no_remap {} {
|
|
mww 0x40048000 0x00
|
|
echo "Notice: interrupt vector set to no remap."
|
|
}
|
|
|
|
$_TARGETNAME configure -event reset-init {
|
|
set_sysclk_500khz
|
|
set_no_remap
|
|
}
|