mirror of
https://git.code.sf.net/p/openocd/code
synced 2024-11-22 04:56:28 +00:00
4157732bd8
For historical reasons, no license information was added to the
tcl files. This makes trivial adding the SPDX tag through script:
fgrep -rL SPDX tcl/board | while read a;do \
sed -i '1{i# SPDX-License-Identifier: GPL-2.0-or-later\n
}' $a;done
With no specific license information from the author, let's extend
the OpenOCD project license GPL-2.0-or-later to the files.
Change-Id: Ibcf7da62e842aafd036a78db9ea2b9f11f79af16
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7028
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
89 lines
1.6 KiB
INI
89 lines
1.6 KiB
INI
# SPDX-License-Identifier: GPL-2.0-or-later
|
|
|
|
#
|
|
# Ethernut 3 board configuration file
|
|
#
|
|
# http://www.ethernut.de/en/hardware/enut3/
|
|
|
|
|
|
# AT91R40008-66AU ARM7TDMI Microcontroller
|
|
# 256kB internal RAM
|
|
source [find target/at91r40008.cfg]
|
|
|
|
|
|
# AT49BV322A-70TU NOR Flash
|
|
# 2M x 16 mode at address 0x10000000
|
|
# Common flash interface supported
|
|
#
|
|
set _FLASHNAME $_CHIPNAME.flash
|
|
flash bank $_FLASHNAME cfi 0x10000000 0x400000 2 2 $_TARGETNAME
|
|
|
|
|
|
# Micrel MIC2775-29YM5 Supervisor
|
|
# Reset output will remain active for 280ms (maximum)
|
|
#
|
|
adapter srst delay 300
|
|
jtag_ntrst_delay 300
|
|
|
|
|
|
arm7_9 fast_memory_access enable
|
|
arm7_9 dcc_downloads enable
|
|
adapter speed 16000
|
|
|
|
|
|
# Target events
|
|
#
|
|
$_TARGETNAME configure -event reset-init { board_init }
|
|
|
|
# Initialize board hardware
|
|
#
|
|
proc board_init { } {
|
|
board_remap
|
|
flash probe 0
|
|
}
|
|
|
|
# Memory remap
|
|
#
|
|
proc board_remap {{VERBOSE 0}} {
|
|
# CS0: NOR flash
|
|
# 16MB @ 0x10000000
|
|
# 16-bit data bus
|
|
# 4 wait states
|
|
#
|
|
mww 0xffe00000 0x1000212d
|
|
|
|
# CS1: Ethernet controller
|
|
# 1MB @ 0x20000000
|
|
# 16-bit data bus
|
|
# 2 wait states
|
|
# Byte select access
|
|
#
|
|
mww 0xffe00004 0x20003025
|
|
|
|
# CS2: CPLD registers
|
|
# 1MB @ 0x21000000
|
|
# 8-bit data bus
|
|
# 2 wait states
|
|
#
|
|
mww 0xffe00008 0x21002026
|
|
|
|
# CS3: Expansion bus
|
|
# 1MB @ 0x22000000
|
|
# 8-bit data bus
|
|
# 8 wait states
|
|
#
|
|
mww 0xffe00010 0x22002e3e
|
|
|
|
# Remap command
|
|
#
|
|
mww 0xffe00020 0x00000001
|
|
|
|
if {$VERBOSE != 0} {
|
|
echo "0x00000000 RAM"
|
|
echo "0x10000000 Flash"
|
|
echo "0x20000000 Ethernet"
|
|
echo "0x21000000 CPLD"
|
|
echo "0x22000000 Expansion"
|
|
}
|
|
}
|