msm8916-openwrt/target/linux/mediatek/dts/mt7986a-netcore-n60.dts
Chukun Pan 4ae474afbd mediatek: filogic: add Netcore N60 support
Hardware specification:
  SoC: MediaTek MT7986A 4x A53
  Flash: ESMT F50L1G41LB 128MB
  RAM: W632GU6NB DDR3 256MB
  Ethernet: 1x 2.5G + 4x 1G
  WiFi1: MT7975N 2.4GHz 4T4R
  WiFi2: MT7975PN 5GHz 4T4R
  Button: Reset, WPS
  Power: DC 12V 2A

Flash instructions:
  1. Connect to the router using ssh or telnet,
     username: useradmin, password is the web
     login password of the router.
  2. Use scp to upload bl31-uboot.fip and flash:
     "mtd write xxx-preloader.bin spi0.0"
     "mtd write xxx-bl31-uboot.fip FIP"
     "mtd erase ubi"
  3. Connect to the router via the Lan port,
     set a static ip of your PC.
     (ip 192.168.1.254, gateway 192.168.1.1)
  4. Download initramfs image, reboot router,
     waiting for tftp recovery to complete.
  5. After openwrt boots up, perform sysupgrade.

Note:
  1. Back up all mtd partitions before flashing.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2024-03-29 22:54:28 +01:00

285 lines
4.7 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
#include "mt7986a.dtsi"
/ {
model = "Netcore N60";
compatible = "netcore,n60", "mediatek,mt7986a";
aliases {
serial0 = &uart0;
label-mac-device = &gmac0;
led-boot = &led_status_red;
led-failsafe = &led_status_red;
led-running = &led_status_blue;
led-upgrade = &led_status_blue;
};
chosen {
stdout-path = "serial0:115200n8";
};
memory {
reg = <0 0x40000000 0 0x10000000>;
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
linux,code = <KEY_RESTART>;
gpios = <&pio 9 GPIO_ACTIVE_LOW>;
};
mesh {
label = "mesh";
linux,code = <KEY_WPS_BUTTON>;
gpios = <&pio 10 GPIO_ACTIVE_LOW>;
};
};
leds {
compatible = "gpio-leds";
led_status_red: status-red {
color = <LED_COLOR_ID_RED>;
function = LED_FUNCTION_STATUS;
gpios = <&pio 29 GPIO_ACTIVE_LOW>;
};
led_status_blue: status-blue {
color = <LED_COLOR_ID_BLUE>;
function = LED_FUNCTION_STATUS;
gpios = <&pio 32 GPIO_ACTIVE_LOW>;
};
};
};
&crypto {
status = "okay";
};
&eth {
status = "okay";
gmac0: mac@0 {
compatible = "mediatek,eth-mac";
reg = <0>;
phy-mode = "2500base-x";
nvmem-cells = <&macaddr_lan>;
nvmem-cell-names = "mac-address";
fixed-link {
speed = <2500>;
full-duplex;
pause;
};
};
gmac1: mac@1 {
compatible = "mediatek,eth-mac";
reg = <1>;
phy-handle = <&phy6>;
phy-mode = "2500base-x";
nvmem-cells = <&macaddr_wan>;
nvmem-cell-names = "mac-address";
};
mdio: mdio-bus {
#address-cells = <1>;
#size-cells = <0>;
};
};
&mdio {
reset-delay-us = <600>;
reset-post-delay-us = <20000>;
reset-gpios = <&pio 6 GPIO_ACTIVE_LOW>;
phy6: phy@6 {
compatible = "ethernet-phy-ieee802.3-c45";
reg = <6>;
mxl,led-config = <0x0 0x0 0x0 0x3f0>;
};
switch: switch@1f {
compatible = "mediatek,mt7531";
reg = <31>;
reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
interrupt-controller;
#interrupt-cells = <1>;
interrupt-parent = <&pio>;
interrupts = <66 IRQ_TYPE_LEVEL_HIGH>;
};
};
&switch {
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
label = "lan1";
};
port@1 {
reg = <1>;
label = "lan2";
};
port@3 {
reg = <3>;
label = "lan3";
};
port@4 {
reg = <4>;
label = "lan4";
};
port@6 {
reg = <6>;
ethernet = <&gmac0>;
phy-mode = "2500base-x";
fixed-link {
speed = <2500>;
full-duplex;
pause;
};
};
};
};
&spi0 {
pinctrl-names = "default";
pinctrl-0 = <&spi_flash_pins>;
status = "okay";
flash@0 {
compatible = "spi-nand";
#address-cells = <1>;
#size-cells = <1>;
reg = <0>;
spi-max-frequency = <20000000>;
spi-tx-bus-width = <4>;
spi-rx-bus-width = <4>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "BL2";
reg = <0x0000000 0x0100000>;
read-only;
};
partition@100000 {
label = "u-boot-env";
reg = <0x0100000 0x0080000>;
};
factory: partition@180000 {
label = "Factory";
reg = <0x0180000 0x0200000>;
read-only;
};
partition@380000 {
label = "FIP";
reg = <0x0380000 0x0200000>;
read-only;
};
partition@580000 {
label = "ubi";
reg = <0x0580000 0x7280000>;
};
};
};
};
&pio {
spi_flash_pins: spi-flash-pins-33-to-38 {
mux {
function = "spi";
groups = "spi0", "spi0_wp_hold";
};
conf-pu {
pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
drive-strength = <8>;
mediatek,pull-up-adv = <0>; /* bias-disable */
};
conf-pd {
pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
drive-strength = <8>;
mediatek,pull-down-adv = <0>; /* bias-disable */
};
};
wf_2g_5g_pins: wf_2g_5g-pins {
mux {
function = "wifi";
groups = "wf_2g", "wf_5g";
};
conf {
pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
"WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
"WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
"WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
"WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
"WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
"WF1_TOP_CLK", "WF1_TOP_DATA";
drive-strength = <4>;
};
};
};
&trng {
status = "okay";
};
&uart0 {
status = "okay";
};
&watchdog {
status = "okay";
};
&wifi {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&wf_2g_5g_pins>;
mediatek,mtd-eeprom = <&factory 0x0>;
};
&factory {
nvmem-layout {
compatible = "fixed-layout";
#address-cells = <1>;
#size-cells = <1>;
macaddr_lan: macaddr@1fef20 {
reg = <0x1fef20 0x6>;
};
macaddr_wan: macaddr@1fef26 {
reg = <0x1fef26 0x6>;
};
};
};