Secure key does not exist EN7523DRAMC V0.5 dram_type = 5, speed = 1866 Final Impdance Cal Result: OCDP:0x1b, OCDN:0x1e, ODTP:0x6, ODTN:0x6 DDR1866 PLL setting init [Dramc] PCDDR3 AC Timing update Fire MRW command... ModeReg.2, value.0x20 done Fire MRW command... ModeReg.3, value.0x0 done Fire MRW command... ModeReg.1, value.0x6 done Fire MRW command... ModeReg.0, value.0x1114 done Fire MRW command... ModeReg.1, value.0x86 done Fire MRW command... ModeReg.1, value.0x6 done Calculate size. DRAM size=512MB U-Boot 2023.07.02-OpenWrt-r23630-842932a63d-00059-g88f17672a-dirty (Sep 10 2024 - 12:34:36 +0200) CPU: Airoha EN7529DT DRAM: 496 MiB Core: 7 devices, 6 uclasses, devicetree: fit spi-nand: spi_nand spinand@0: Winbond SPI NAND was found. spi-nand: spi_nand spinand@0: 256 MiB, block size: 128 KiB, page size: 2048, OOB size: 128 + 0x000000000000-0x000010000000 : "spi-nand0" + 0x000000000000-0x000000100000 : "u-boot" + 0x000000100000-0x000010000000 : "ubi" In: serial@1fbf0000 Out: serial@1fbf0000 Err: serial@1fbf0000 Net: eth0: en75xx-eth Loading Environment from UBI... ubi0: default fastmap pool size: 100 ubi0: default fastmap WL pool size: 50 ubi0: attaching mtd2 ubi0: scanning is finished ubi0: attached mtd2 (name "ubi", size 255 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 2022, bad PEBs: 18, corrupted PEBs: 0 ubi0: user volume: 11, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 1985439503 ubi0: available PEBs: 14, total reserved PEBs: 2008, PEBs reserved for bad PEB handling: 22 Read 126976 bytes from volume env1 to 9eaf6280 Read 126976 bytes from volume env2 to 9eb152c0 OK apply matching dtb: en7523-laxy Autoboot in 2 seconds =>          bootm uboot.bin bootm - boot application image from memory Usage: bootm [addr [arg ...]] - boot application image stored in memory passing arguments 'arg ...'; when booting a Linux kernel, 'arg' can be the address of an initrd image When booting a Linux kernel which requires a flat device-tree a third argument is required which is the address of the device-tree blob. To boot that kernel without an initrd image, use a '-' for the second argument. If you do not pass a third a bd_info struct will be passed instead For the new multi component uImage format (FIT) addresses must be extended to include component or configuration unit name: addr: - direct component image specification addr# - configuration specification Use iminfo command to get the list of existing component images and configurations. Sub-commands to do part of the bootm sequence. The sub-commands must be issued in the order below (it's ok to not issue all sub-commands): start [addr [arg ...]] loados - load OS image ramdisk - relocate initrd, set env initrd_start/initrd_end fdt - relocate flat device tree cmdline - OS specific command line processing/setup bdt - OS specific bd_info processing prep - OS specific prep before relocation or go go - start OS => tftpboot b uboot.b bin en75xx-eth: using internal switch Using en75xx-eth device TFTP from server 192.168.1.100; our IP address is 192.168.1.1 Filename 'uboot.bin'. Load address: 0x80500000 Loading: *################################################## 296.8 KiB 53.7 KiB/s done Bytes transferred = 303936 (4a340 hex) => bootm 0y x80500200 ## Loading kernel from FIT Image at 80500200 ... Using 'conf-uboot' configuration Trying 'kernel-1' kernel subimage Description: ARM OpenWrt Linux-u-boot Type: Kernel Image Compression: lzma compressed Data Start: 0x805002e4 Data Size: 295676 Bytes = 288.7 KiB Architecture: ARM OS: Linux Load Address: 0x80200000 Entry Point: 0x80200000 Hash algo: crc32 Hash value: f1c4e542 Hash algo: sha1 Hash value: 76e2e51cb05109fa954ee9b8939ec56b39a0ba87 Verifying Hash Integrity ... crc32+ sha1+ OK ## Loading fdt from FIT Image at 80500200 ... Using 'conf-uboot' configuration Trying 'fdt-1' fdt subimage Description: ARM OpenWrt tplink_xx230v_v1 device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x8054871c Data Size: 6352 Bytes = 6.2 KiB Architecture: ARM Load Address: 0x82000000 Hash algo: crc32 Hash value: 4cb30ee3 Hash algo: sha1 Hash value: ce94272b0b0ce9cec2bdcbffcb2880c7ade6529d Verifying Hash Integrity ... crc32+ sha1+ OK Loading fdt from 0x8054871c to 0x82000000 Booting using the fdt blob at 0x82000000 Working FDT set to 82000000 Uncompressing Kernel Image ERROR: reserving fdt memory region failed (addr=80000000 size=40000 flags=4) ERROR: reserving fdt memory region failed (addr=80000000 size=40000 flags=4) Loading Device Tree to 9eb2b000, end 9eb2f8cf ... OK Working FDT set to 9eb2b000 Starting kernel ... U-Boot 2026.01-OpenWrt-r0-7e9932c (Apr 15 2026 - 22:19:08 +0000) CPU: Airoha EN7523/EN7529/EN7562 Model: TP-Link xx230v v1 DRAM: 512 MiB Core: 24 devices, 16 uclasses, devicetree: separate Loading Environment from UBI... spi-nand: spi_nand nand@0: Winbond SPI NAND was found. spi-nand: spi_nand nand@0: 256 MiB, block size: 128 KiB, page size: 2048, OOB size: 128 ubi0 error: ubi_read_volume_table: the layout volume was not found ubi0 error: ubi_attach_mtd_dev: failed to attach mtd5, error -22 UBI error: cannot attach mtd5 UBI error: cannot initialize UBI, error -22 UBI init error 22 Please check, if the correct MTD partition is used (size big enough?) ** Cannot find mtd partition "ubi" In: serial Out: serial Err: serial Net: Warning: ethernet@1fb50000 (eth0) using random MAC address - 3a:67:24:fb:06:fe eth0: ethernet@1fb50000 Hit any key to stop autoboot: 3  0 U-Boot>    se  bootm laxy.bin bootm - boot application image from memory Usage: bootm [addr [arg ...]] - boot application image stored in memory passing arguments 'arg ...'; when booting a Linux kernel, 'arg' can be the address of an initrd image When booting a Linux kernel which requires a flat device-tree a third argument is required which is the address of the device-tree blob. To boot that kernel without an initrd image, use a '-' for the second argument. If you do not pass a third a bd_info struct will be passed instead For the new multi component uImage format (FIT) addresses must be extended to include component or configuration unit name: addr: - direct component image specification addr# - configuration specification Use iminfo command to get the list of existing component images and configurations. Sub-commands to do part of the bootm sequence. The sub-commands must be issued in the order below (it's ok to not issue all sub-commands): start [addr [arg ...]] loados - load OS image ramdisk - relocate initrd, set env initrd_start/initrd_end fdt - relocate flat device tree cmdline - OS specific command line processing/setup bdt - OS specific bd_info processing prep - OS specific prep before relocation or go go - start OS U-Boot> tftboot laxy.bin Unknown command 'tftboot' - try 'help' U-Boot> tftpboot laxy.bin Using ethernet@1fb50000 device TFTP from server 192.168.1.10; our IP address is 192.168.1.1 Filename 'laxy.bin'. Load address: 0x86a00000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################# 587.9 KiB/s done Bytes transferred = 23788852 (16afd34 hex) U-Boot> bootm ## Loading kernel (any) from FIT Image at 86a00000 ... Using 'config-1' configuration Trying 'kernel-1' kernel subimage Description: ARM OpenWrt Linux-6.12.87 Type: Kernel Image Compression: lzma compressed Data Start: 0x86a000e4 Data Size: 23772560 Bytes = 22.7 MiB Architecture: ARM OS: Linux Load Address: 0x80208000 Entry Point: 0x80208000 Hash algo: crc32 Hash value: 977c9243 Hash algo: sha1 Hash value: 8c1bb3ce824bac6b01b2617411c835da745b42ed Verifying Hash Integrity ... crc32+ sha1+ OK ## Loading fdt (any) from FIT Image at 86a00000 ... Using 'config-1' configuration Trying 'fdt-1' fdt subimage Description: ARM OpenWrt genexis_laxy device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x880abfac Data Size: 14917 Bytes = 14.6 KiB Architecture: ARM Hash algo: crc32 Hash value: e86a3ee3 Hash algo: sha1 Hash value: 166f9efa351540cd55c8bff2b9cecefddb656240 Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x880abfac Working FDT set to 880abfac Uncompressing Kernel Image to 80208000 Loading Device Tree to 9eb1e000, end 9eb24a44 ... OK Working FDT set to 9eb1e000 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.12.87 (sirherobrine23@matheus-note) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 14.3.0 r33479-5f7ec5c8b9) 14.3.0, GNU ld (GNU Binutils) 2.44) #0 SMP Sat May 9 15:26:26 2026 [ 0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Heimgard/Genexis laxy [ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000 [ 0.000000] earlycon: ns16550 at MMIO32 0x1fbf0000 (options '115200n8') [ 0.000000] printk: legacy bootconsole [ns16550] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080200000-0x000000009fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080200000-0x0000000083ffffff] [ 0.000000] node 0: [mem 0x0000000084000000-0x00000000844fffff] [ 0.000000] node 0: [mem 0x0000000084500000-0x00000000848fffff] [ 0.000000] node 0: [mem 0x0000000084900000-0x00000000862fffff] [ 0.000000] node 0: [mem 0x0000000086300000-0x000000009fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x000000009fffffff] [ 0.000000] On node 0, zone Normal: 512 pages in unavailable ranges [ 0.000000] OF: reserved mem: 0x80000000..0x8003ffff (256 KiB) nomap non-reusable atf@80000000 [ 0.000000] OF: reserved mem: 0x84000000..0x840fffff (1024 KiB) nomap non-reusable npu_binary@84000000 [ 0.000000] OF: reserved mem: 0x84100000..0x844fffff (4096 KiB) nomap non-reusable qdma0-buf@84100000 [ 0.000000] OF: reserved mem: 0x84900000..0x84cfffff (4096 KiB) nomap non-reusable qdma1-buf@84900000 [ 0.000000] OF: reserved mem: 0x84d00000..0x862fffff (22528 KiB) nomap non-reusable npu-pkt@84d00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 14 pages/cpu s25228 r8192 d23924 u57344 [ 0.000000] Kernel command line: console=ttyS0,115200 earlycon [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130560 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=2. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GICv3: 256 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: GICv3 features: 16 PPIs [ 0.000000] GICv3: GICD_CTRL.DS=0, SCR_EL3.FIQ=0 [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x09080000 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns [ 0.000001] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns [ 0.008801] Switching to timer-based delay loop, resolution 40ns [ 0.015568] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000) [ 0.026957] CPU: Testing write buffer coherency: ok [ 0.032349] pid_max: default: 32768 minimum: 301 [ 0.044079] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.052128] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.063656] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.070881] Setting up static identity map for 0x80300000 - 0x80300060 [ 0.078239] rcu: Hierarchical SRCU implementation. [ 0.083503] rcu: Max phase no-delay instances is 1000. [ 0.089510] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 0.098707] smp: Bringing up secondary CPUs ... [ 0.118768] GICv3: CPU1: found redistributor 1 region 0:0x090a0000 [ 0.118822] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.118966] smp: Brought up 1 node, 2 CPUs [ 0.136481] SMP: Total of 2 processors activated (100.00 BogoMIPS). [ 0.143380] CPU: All CPU(s) started in SVC mode. [ 0.148942] Memory: 452588K/522240K available (7695K kernel code, 622K rwdata, 2020K rodata, 20480K init, 217K bss, 68520K reserved, 0K cma-reserved) [ 0.168105] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.178966] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.189852] pinctrl core: initialized pinctrl subsystem [ 0.197633] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.204427] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.212770] thermal_sys: Registered thermal governor 'step_wise' [ 0.212857] cpuidle: using governor menu [ 0.226434] /pcie@1fa91000: Fixed dependency cycle(s) with /pcie@1fa91000/interrupt-controller [ 0.236372] /pcie@1fa92000: Fixed dependency cycle(s) with /pcie@1fa92000/interrupt-controller [ 0.254749] SCSI subsystem initialized [ 0.259150] usbcore: registered new interface driver usbfs [ 0.265216] usbcore: registered new interface driver hub [ 0.271148] usbcore: registered new device driver usb [ 0.278020] clocksource: Switched to clocksource arch_sys_counter [ 0.290763] NET: Registered PF_INET protocol family [ 0.296289] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.305166] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.314416] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.322940] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.331493] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.339457] TCP: Hash tables configured (established 4096 bind 4096) [ 0.346732] MPTCP token hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.354944] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.362165] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.370260] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.376509] PCI: CLS 0 bytes, default 64 [ 0.382327] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.391104] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.397524] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.691935] mtk-pcie 1fa91000.pcie: host bridge /pcie@1fa91000 ranges: [ 0.699247] mtk-pcie 1fa91000.pcie: MEM 0x0020000000..0x0021ffffff -> 0x0020000000 [ 1.226655] mtk-pcie 1fa91000.pcie: PCI host bridge to bus 0000:00 [ 1.233523] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.239594] pci_bus 0000:00: root bus resource [mem 0x20000000-0x21ffffff] [ 1.247358] pci 0000:00:00.0: [14c3:0810] type 01 class 0x060400 PCIe Root Port [ 1.255627] pci 0000:00:00.0: BAR 0: can't handle BAR larger than 4GB (size 0x200000000) [ 1.264534] pci 0000:00:00.0: BAR 0 [mem size 0x00000001 64bit pref disabled] [ 1.272455] pci 0000:00:00.0: PCI bridge to [bus 00] [ 1.278031] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff] [ 1.287731] PCI: bus0: Fast back to back transfers disabled [ 1.293924] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.303404] pci 0000:01:00.0: [14c3:790a] type 00 class 0x028000 PCIe Endpoint [ 1.311563] pci 0000:01:00.0: BAR 0 [mem 0x00000000-0x000fffff 64bit pref] [ 1.319245] pci 0000:01:00.0: BAR 2 [mem 0x00000000-0x00007fff 64bit] [ 1.326426] pci 0000:01:00.0: BAR 4 [mem 0x00000000-0x00000fff 64bit pref] [ 1.334738] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 1.341839] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link) [ 1.358874] PCI: bus1: Fast back to back transfers disabled [ 1.365010] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 1.372385] pci 0000:00:00.0: bridge window [mem 0x20000000-0x201fffff]: assigned [ 1.380638] pci 0000:00:00.0: BAR 0 [mem 0x20200000 64bit pref disabled]: assigned [ 1.389018] pci 0000:00:00.0: BAR 0: error updating (0x2020000c != 0x0000000c) [ 1.397001] pci 0000:01:00.0: BAR 0 [mem 0x20000000-0x200fffff 64bit pref]: assigned [ 1.405619] pci 0000:01:00.0: BAR 2 [mem 0x20100000-0x20107fff 64bit]: assigned [ 1.413754] pci 0000:01:00.0: BAR 4 [mem 0x20108000-0x20108fff 64bit pref]: assigned [ 1.422356] pci 0000:00:00.0: PCI bridge to [bus 01] [ 1.427843] pci 0000:00:00.0: bridge window [mem 0x20000000-0x201fffff] [ 1.435400] pci_bus 0000:00: resource 4 [mem 0x20000000-0x21ffffff] [ 1.442307] pci_bus 0000:01: resource 1 [mem 0x20000000-0x201fffff] [ 1.449899] pcieport 0000:00:00.0: enabling device (0140 -> 0142) [ 1.457368] pcieport 0000:00:00.0: PME: Signaling with IRQ 30 [ 1.465303] mtk-pcie 1fa92000.pcie: host bridge /pcie@1fa92000 ranges: [ 1.472552] mtk-pcie 1fa92000.pcie: MEM 0x0022000000..0x0023ffffff -> 0x0022000000 [ 1.628941] mtk-pcie 1fa92000.pcie: PCI host bridge to bus 0001:00 [ 1.635751] pci_bus 0001:00: root bus resource [bus 00-ff] [ 1.641839] pci_bus 0001:00: root bus resource [mem 0x22000000-0x23ffffff] [ 1.649708] pci 0001:00:01.0: [14c3:0811] type 01 class 0x060400 PCIe Root Port [ 1.657921] pci 0001:00:01.0: BAR 0: can't handle BAR larger than 4GB (size 0x200000000) [ 1.666864] pci 0001:00:01.0: BAR 0 [mem size 0x00000001 64bit pref disabled] [ 1.674812] pci 0001:00:01.0: PCI bridge to [bus 00] [ 1.680363] pci 0001:00:01.0: bridge window [mem 0x00000000-0x000fffff] [ 1.690060] PCI: bus0: Fast back to back transfers disabled [ 1.696212] pci 0001:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.705768] pci 0001:01:00.0: [14c3:7906] type 00 class 0x028000 PCIe Endpoint [ 1.713933] pci 0001:01:00.0: BAR 0 [mem 0x00000000-0x000fffff 64bit pref] [ 1.721629] pci 0001:01:00.0: BAR 2 [mem 0x00000000-0x00007fff 64bit] [ 1.728844] pci 0001:01:00.0: BAR 4 [mem 0x00000000-0x00000fff 64bit pref] [ 1.737149] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold [ 1.744263] pci 0001:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0001:00:01.0 (capable of 8.000 Gb/s with 5.0 GT/s PCIe x2 link) [ 1.761333] PCI: bus1: Fast back to back transfers disabled [ 1.767466] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 [ 1.774829] pci 0001:00:01.0: bridge window [mem 0x22000000-0x221fffff]: assigned [ 1.783105] pci 0001:00:01.0: BAR 0 [mem 0x22200000 64bit pref disabled]: assigned [ 1.791494] pci 0001:00:01.0: BAR 0: error updating (0x2220000c != 0x0000000c) [ 1.799492] pci 0001:01:00.0: BAR 0 [mem 0x22000000-0x220fffff 64bit pref]: assigned [ 1.808101] pci 0001:01:00.0: BAR 2 [mem 0x22100000-0x22107fff 64bit]: assigned [ 1.816213] pci 0001:01:00.0: BAR 4 [mem 0x22108000-0x22108fff 64bit pref]: assigned [ 1.824813] pci 0001:00:01.0: PCI bridge to [bus 01] [ 1.830312] pci 0001:00:01.0: bridge window [mem 0x22000000-0x221fffff] [ 1.837843] pci_bus 0001:00: resource 4 [mem 0x22000000-0x23ffffff] [ 1.844773] pci_bus 0001:01: resource 1 [mem 0x22000000-0x221fffff] [ 1.852362] pcieport 0001:00:01.0: enabling device (0140 -> 0142) [ 1.859819] pcieport 0001:00:01.0: PME: Signaling with IRQ 32 [ 1.868073] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 1.876025] printk: legacy console [ttyS0] disabled [ 1.881884] 1fbf0000.serial: ttyS0 at MMIO 0x1fbf0000 (irq = 33, base_baud = 115200) is a 16550 [ 1.891533] printk: legacy console [ttyS0] enabled [ 1.891533] printk: legacy console [ttyS0] enabled [ 1.901635] printk: legacy bootconsole [ns16550] disabled [ 1.901635] printk: legacy bootconsole [ns16550] disabled [ 1.917475] airoha-spi 1fa10000.spi: boot type: NAND [ 1.923135] spi-nand spi0.0: Winbond SPI NAND was found. [ 1.928499] spi-nand spi0.0: 256 MiB, block size: 128 KiB, page size: 2048, OOB size: 128 [ 1.938388] random: crng init done [ 18.311552] 2 fixed-partitions partitions found on MTD device spi0.0 [ 18.318240] Creating 2 MTD partitions on "spi0.0": [ 18.323048] 0x000000000000-0x000000100000 : "u-boot" [ 18.331760] 0x000000100000-0x000010000000 : "ubi" [ 18.895254] ubi0: attaching mtd1 [ 19.976565] ubi0: scanning is finished [ 19.990509] ubi0: attached mtd1 (name "ubi", size 255 MiB) [ 19.996031] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 20.002940] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 20.009752] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 20.016714] ubi0: good PEBs: 2022, bad PEBs: 18, corrupted PEBs: 0 [ 20.022905] ubi0: user volume: 11, internal volumes: 1, max. volumes count: 128 [ 20.030222] ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 1985439503 [ 20.039365] ubi0: available PEBs: 16, total reserved PEBs: 2006, PEBs reserved for bad PEB handling: 22 [ 20.048793] ubi0: background thread "ubi_bgt0d" started, PID 154 [ 20.054834] spi_master spi0: cannot find modalias for /spi@1fa10000/flash@1 [ 20.061893] spi_master spi0: Failed to create SPI device for /spi@1fa10000/flash@1 [ 20.149564] airoha-npu 1e900000.npu: L2C sram: 0x00, FPGA Stage: 0 [ 21.108009] airoha-npu 1e900000.npu: wlan get msg: id 10, core 0, body size 4 [ 21.115172] airoha-npu 1e900000.npu: NPU not support get version [ 21.135112] mtk-eip93 1fb70000.crypto: EIP93:3:0:1,PE(0xfe007:0x41710041) [ 21.142426] NET: Registered PF_INET6 protocol family [ 21.148747] Segment Routing with IPv6 [ 21.152461] In-situ OAM (IOAM) with IPv6 [ 21.156474] NET: Registered PF_PACKET protocol family [ 21.161780] 8021q: 802.1Q VLAN Support v1.8 [ 21.166059] Registering SWP/SWPB emulation handler [ 21.246511] mt7530-mmio 1fb58000.switch: configuring for fixed/internal link mode [ 21.254364] mt7530-mmio 1fb58000.switch: Link is Up - 10Gbps/Full - flow control rx/tx [ 21.274898] mt7530-mmio 1fb58000.switch lan1 (uninitialized): PHY [mt7530-0:09] driver [Airoha AN7523 PHY] (irq=POLL) [ 21.286613] mt7530-mmio 1fb58000.switch lan2 (uninitialized): PHY [mt7530-0:0a] driver [Airoha AN7523 PHY] (irq=POLL) [ 21.298303] mt7530-mmio 1fb58000.switch lan3 (uninitialized): PHY [mt7530-0:0b] driver [Airoha AN7523 PHY] (irq=POLL) [ 21.309829] airoha_eth 1fb50000.ethernet eth0: entered promiscuous mode [ 21.316535] DSA: tree 0 setup [ 21.320404] clk: Disabling unused clocks [ 21.324355] PM: genpd: Disabling unused power domains [ 21.350263] Freeing unused kernel image (initmem) memory: 20480K [ 21.356608] Run /init as init process [ 22.017306] init: Console is alive [ 22.020994] init: - watchdog - [ 22.036703] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 22.052643] gpio_button_hotplug: loading out-of-tree module taints kernel. [ 22.075797] usbcore: registered new interface driver usb-storage [ 22.088940] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 22.106701] init: - preinit - Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 23.316463] procd: - early - [ 23.319643] procd: - watchdog - ^[[C[ 23.853263] procd: - watchdog - [ 23.856935] procd: - ubus - [ 24.012360] procd: - init - Please press Enter to activate this console. [ 24.386023] kmodloader: loading kernel modules from /etc/modules.d/* [ 24.704636] i2c_dev: i2c /dev entries driver [ 24.715609] ntfs3: Enabled Linux POSIX ACLs support [ 24.724761] Loading modules backported from Linux version v6.18.26-0-g1fe060681 [ 24.732160] Backport generated by backports.git 6ecbb44 [ 24.816028] usbcore: registered new interface driver ums-alauda [ 24.839365] usbcore: registered new interface driver ums-cypress [ 24.846574] usbcore: registered new interface driver ums-datafab [ 24.869630] usbcore: registered new interface driver ums-freecom [ 24.876803] usbcore: registered new interface driver ums-isd200 [ 24.890653] usbcore: registered new interface driver ums-jumpshot [ 24.902906] usbcore: registered new interface driver ums-karma [ 24.920930] usbcore: registered new interface driver ums-sddr09 [ 24.928474] usbcore: registered new interface driver ums-sddr55 [ 24.935977] usbcore: registered new interface driver ums-usbat [ 24.982988] xt_time: kernel timezone is -0000 [ 25.082553] mt7915e_hif 0000:01:00.0: enabling device (0140 -> 0142) [ 25.089355] mt7915e 0001:01:00.0: enabling device (0140 -> 0142) [ 25.167565] urngd: v1.0.2 started. [ 25.258266] mt7915e 0001:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20240823172725a [ 25.288406] mt7915e 0001:01:00.0: WM Firmware Version: ____000000, Build Time: 20240823172741 [ 25.347812] mt7915e 0001:01:00.0: WA Firmware Version: DEV_000000, Build Time: 20240823172837 [ 25.509953] mt7915e 0001:01:00.0: registering led 'mt76-phy0' [ 25.598390] mt7915e 0001:01:00.0: registering led 'mt76-phy1' [ 25.722960] PPP generic driver version 2.4.2 [ 25.742634] NET: Registered PF_PPPOX protocol family [ 25.[ 37.370915] br-lan: port 1(eth0) entered blocking state [ 37.376187] br-lan: port 1(eth0) entered disabled state [ 37.381561] airoha_eth 1fb50000.ethernet eth0: entered allmulticast mode [ 37.390351] br-lan: port 1(eth0) entered blocking state [ 37.395643] br-lan: port 1(eth0) entered forwarding state BusyBox v1.37.0 (2026-01-02 17:07:02 UTC) built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt SNAPSHOT, r34374-359b1f13fb1 ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@OpenWrt:~# ifconfig br-lan Link encap:Ethernet HWaddr 74:AC:F9:92:B0:DD inet addr:192.168.2.1 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fdd0:96bf:4bbd::1/60 Scope:Global inet6 addr: fe80::76ac:f9ff:fe92:b0dd/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1504 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:1832 (1.7 KiB) eth0 Link encap:Ethernet HWaddr 74:AC:F9:92:B0:DD UP BROADCAST RUNNING MULTICAST MTU:1504 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:968 (968.0 B) Interrupt:36 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:120 errors:0 dropped:0 overruns:0 frame:0 TX packets:120 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9360 (9.1 KiB) TX bytes:9360 (9.1 KiB) root@OpenWrt:~# miiping google 192.168.100..10 PING 192.168.1.10 (192.168.1.10): 56 data bytes ping: sendto: Network unreachable root@OpenWrt:~# ifcoifconifig br-lan br-lan Link encap:Ethernet HWaddr 74:AC:F9:92:B0:DD inet addr:192.168.2.1 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fdd0:96bf:4bbd::1/60 Scope:Global inet6 addr: fe80::76ac:f9ff:fe92:b0dd/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1504 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:13 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:2006 (1.9 KiB) root@OpenWrt:~# iiping 192.168.2.100 PING 192.168.2.10 (192.168.2.10): 56 data bytes ^C --- 192.168.2.10 ping statistics --- 11 packets transmitted, 0 packets received, 100% packet loss root@OpenWrt:~# root@OpenWrt:~# ifconfig  | more br-lan Link encap:Ethernet HWaddr 74:AC:F9:92:B0:DD  inet addr:192.168.2.1 Bcast:192.168.2.255 Mask:255.255.255.0  inet6 addr: fdd0:96bf:4bbd::1/60 Scope:Global  inet6 addr: fe80::76ac:f9ff:fe92:b0dd/64 Scope:Link  UP BROADCAST RUNNING MULTICAST MTU:1504 Metric:1  RX packets:0 errors:0 dropped:0 overruns:0 frame:0  TX packets:28 errors:0 dropped:0 overruns:0 carrier:0  collisions:0 txqueuelen:1000  RX bytes:0 (0.0 B) TX bytes:2636 (2.5 KiB)  eth0 Link encap:Ethernet HWaddr 74:AC:F9:92:B0:DD  UP BROADCAST RUNNING MULTICAST MTU:1504 Metric:1  RX packets:0 errors:0 dropped:0 overruns:0 frame:0  TX packets:22 errors:0 dropped:0 overruns:0 carrier:0  collisions:0 txqueuelen:1000  RX bytes:0 (0.0 B) TX bytes:1708 (1.6 KiB)  Interrupt:36  lo Link encap:Local Loopback  inet addr:127.0.0.1 Mask:255.0.0.0  inet6 addr: ::1/128 Scope:Host  UP LOOPBACK RUNNING MTU:65536 Metric:1  RX packets:336 errors:0 dropped:0 overruns:0 frame:0 standard input TX packets:28 errors:0 dropped:0 overruns:0 carrier:0  collisions:0 txqueuelen:1000  RX bytes:0 (0.0 B) TX bytes:2636 (2.5 KiB)  eth0 Link encap:Ethernet HWaddr 74:AC:F9:92:B0:DD  UP BROADCAST RUNNING MULTICAST MTU:1504 Metric:1  RX packets:0 errors:0 dropped:0 overruns:0 frame:0  TX packets:22 errors:0 dropped:0 overruns:0 carrier:0  collisions:0 txqueuelen:1000  RX bytes:0 (0.0 B) TX bytes:1708 (1.6 KiB)  Interrupt:36  lo Link encap:Local Loopback  inet addr:127.0.0.1 Mask:255.0.0.0  inet6 addr: ::1/128 Scope:Host  UP LOOPBACK RUNNING MTU:65536 Metric:1  RX packets:336 errors:0 dropped:0 overruns:0 frame:0  TX packets:336 errors:0 dropped:0 overruns:0 carrier:0  collisions:0 txqueuelen:1000  RX bytes:26752 (26.1 KiB) TX bytes:26752 (26.1 KiB)   ~ (END)root@OpenWrt:~# icofconfig br-lan Link encap:Ethernet HWaddr 74:AC:F9:92:B0:DD inet addr:192.168.2.1 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fdd0:96bf:4bbd::1/60 Scope:Global inet6 addr: fe80::76ac:f9ff:fe92:b0dd/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1504 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:28 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:2636 (2.5 KiB) eth0 Link encap:Ethernet HWaddr 74:AC:F9:92:B0:DD UP BROADCAST RUNNING MULTICAST MTU:1504 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:22 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:1708 (1.6 KiB) Interrupt:36 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:336 errors:0 dropped:0 overruns:0 frame:0 TX packets:336 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:26752 (26.1 KiB) TX bytes:26752 (26.1 KiB) root@OpenWrt:~# ping 192.168.2.10 PING 192.168.2.10 (192.168.2.10): 56 data bytes ^C --- 192.168.2.10 ping statistics --- 3 packets transmitted, 0 packets received, 100% packet loss root@OpenWrt:~# root@OpenWrt:~# ping 192.168.2.10 root@OpenWrt:~# ifconfig root@OpenWrt:~# ping 192.168.2.10 PING 192.168.2.10 (192.168.2.10): 56 data bytes ^C --- 192.168.2.10 ping statistics --- 3 packets transmitted, 0 packets received, 100% packet loss root@OpenWrt:~# root@OpenWrt:~# ping 192.168.2.10 PING 192.168.2.10 (192.168.2.10): 56 data bytes ^C --- 192.168.2.10 ping statistics --- 2 packets transmitted, 0 packets received, 100% packet loss root@OpenWrt:~# root@OpenWrt:~# ifcofinfig br-lan Link encap:Ethernet HWaddr 74:AC:F9:92:B0:DD inet addr:192.168.2.1 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fdd0:96bf:4bbd::1/60 Scope:Global inet6 addr: fe80::76ac:f9ff:fe92:b0dd/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1504 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:37 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:3014 (2.9 KiB) eth0 Link encap:Ethernet HWaddr 74:AC:F9:92:B0:DD UP BROADCAST RUNNING MULTICAST MTU:1504 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:31 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:2050 (2.0 KiB) Interrupt:36 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:368 errors:0 dropped:0 overruns:0 frame:0 TX packets:368 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:29520 (28.8 KiB) TX bytes:29520 (28.8 KiB) root@OpenWrt:~# root@OpenWrt:~# ifconfig | more br-lan Link encap:Ethernet HWaddr 74:AC:F9:92:B0:DD  inet addr:192.168.2.1 Bcast:192.168.2.255 Mask:255.255.255.0  inet6 addr: fdd0:96bf:4bbd::1/60 Scope:Global  inet6 addr: fe80::76ac:f9ff:fe92:b0dd/64 Scope:Link  UP BROADCAST RUNNING MULTICAST MTU:1504 Metric:1  RX packets:0 errors:0 dropped:0 overruns:0 frame:0  TX packets:37 errors:0 dropped:0 overruns:0 carrier:0  collisions:0 txqueuelen:1000  RX bytes:0 (0.0 B) TX bytes:3014 (2.9 KiB)  eth0 Link encap:Ethernet HWaddr 74:AC:F9:92:B0:DD  UP BROADCAST RUNNING MULTICAST MTU:1504 Metric:1  RX packets:0 errors:0 dropped:0 overruns:0 frame:0  TX packets:31 errors:0 dropped:0 overruns:0 carrier:0  collisions:0 txqueuelen:1000  RX bytes:0 (0.0 B) TX bytes:2050 (2.0 KiB)  Interrupt:36  lo Link encap:Local Loopback  inet addr:127.0.0.1 Mask:255.0.0.0  inet6 addr: ::1/128 Scope:Host  UP LOOPBACK RUNNING MTU:65536 Metric:1  RX packets:376 errors:0 dropped:0 overruns:0 frame:0 standard inputroot@OpenWrt:~# ifconfigűű -ash: ifconfigű: not found root@OpenWrt:~# roteute Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 * 255.255.255.0 U 0 0 0 br-lan root@OpenWrt:~# pig ng 18292.168.2.1 PING 192.168.2.1 (192.168.2.1): 56 data bytes 64 bytes from 192.168.2.1: seq=0 ttl=64 time=0.215 ms 64 bytes from 192.168.2.1: seq=1 ttl=64 time=0.175 ms ^C --- 192.168.2.1 ping statistics --- 2 packets transmitted, 2 packets received, 0% packet loss round-trip min/avg/max = 0.175/0.195/0.215 ms root@OpenWrt:~# root@OpenWrt:~# ping 192.168.2.110 PING 192.168.2.10 (192.168.2.10): 56 data bytes ^C --- 192.168.2.10 ping statistics --- 5 packets transmitted, 0 packets received, 100% packet loss root@OpenWrt:~# ssh 192.168.2.10 ^C root@OpenWrt:~# Secure key does not exist EN7523DRAMC V0.5 dram_type = 5, speed = 1866 Final Impdance Cal Result: OCDP:0x14, OCDN:0x17, ODTP:0x6, ODTN:0x6 DDR1866 PLL setting init [Dramc] PCDDR3 AC Timing update Fire MRW command... ModeReg.2, value.0x20 done Fire MRW command... ModeReg.3, value.0x0 done Fire MRW command... ModeReg.1, value.0x6 done Fire MRW command... ModeReg.0, value.0x1114 done Fire MRW command... ModeReg.1, value.0x86 done Fire MRW command... ModeReg.1, value.0x6 done Calculate size. DRAM size=512MB U-Boot 2023.07.02-OpenWrt-r23630-842932a63d-00059-g88f17672a-dirty (Sep 10 2024 - 13:20:35 +0200) CPU: Airoha EN7529DT DRAM: 496 MiB Core: 7 devices, 6 uclasses, devicetree: fit spi-nand: spi_nand spinand@0: Winbond SPI NAND was found. spi-nand: spi_nand spinand@0: 256 MiB, block size: 128 KiB, page size: 2048, OOB size: 128 + 0x000000000000-0x000010000000 : "spi-nand0" + 0x000000000000-0x000000100000 : "u-boot" + 0x000000100000-0x000010000000 : "ubi" In: serial@1fbf0000 Out: serial@1fbf0000 Err: serial@1fbf0000 Net: eth0: en75xx-eth Loading Environment from UBI... ubi0: default fastmap pool size: 100 ubi0: default fastmap WL pool size: 50 ubi0: attaching mtd2 ubi0: scanning is finished ubi0: attached mtd2 (name "ubi", size 255 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 2040, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 11, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 5/1, WL threshold: 4096, image sequence number: 702916436 ubi0: available PEBs: 297, total reserved PEBs: 1743, PEBs reserved for bad PEB handling: 40 Read 126976 bytes from volume env1 to 9eaf2980 Read 126976 bytes from volume env2 to 9eb119c0 OK apply matching dtb: en7523-pixly-r2 Autoboot in 2 seconds =>       tftpboot uboot.bin en75xx-eth: using internal switch Using en75xx-eth device TFTP from server 192.168.1.100; our IP address is 192.168.1.1 Filename 'uboot.bin'. Load address: 0x80500000 Loading: *################################################## 296.8 KiB 53.7 KiB/s done Bytes transferred = 303936 (4a340 hex) => botm    bootm     bootm 0x80500200 ## Loading kernel from FIT Image at 80500200 ... Using 'conf-uboot' configuration Trying 'kernel-1' kernel subimage Description: ARM OpenWrt Linux-u-boot Type: Kernel Image Compression: lzma compressed Data Start: 0x805002e4 Data Size: 295676 Bytes = 288.7 KiB Architecture: ARM OS: Linux Load Address: 0x80200000 Entry Point: 0x80200000 Hash algo: crc32 Hash value: f1c4e542 Hash algo: sha1 Hash value: 76e2e51cb05109fa954ee9b8939ec56b39a0ba87 Verifying Hash Integrity ... crc32+ sha1+ OK ## Loading fdt from FIT Image at 80500200 ... Using 'conf-uboot' configuration Trying 'fdt-1' fdt subimage Description: ARM OpenWrt tplink_xx230v_v1 device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x8054871c Data Size: 6352 Bytes = 6.2 KiB Architecture: ARM Load Address: 0x82000000 Hash algo: crc32 Hash value: 4cb30ee3 Hash algo: sha1 Hash value: ce94272b0b0ce9cec2bdcbffcb2880c7ade6529d Verifying Hash Integrity ... crc32+ sha1+ OK Loading fdt from 0x8054871c to 0x82000000 Booting using the fdt blob at 0x82000000 Working FDT set to 82000000 Uncompressing Kernel Image ERROR: reserving fdt memory region failed (addr=80000000 size=40000 flags=4) ERROR: reserving fdt memory region failed (addr=80000000 size=40000 flags=4) Loading Device Tree to 9eb27000, end 9eb2b8cf ... OK Working FDT set to 9eb27000 Starting kernel ... U-Boot 2026.01-OpenWrt-r0-7e9932c (Apr 15 2026 - 22:19:08 +0000) CPU: Airoha EN7523/EN7529/EN7562 Model: TP-Link xx230v v1 DRAM: 512 MiB Core: 24 devices, 16 uclasses, devicetree: separate Loading Environment from UBI... spi-nand: spi_nand nand@0: Winbond SPI NAND was found. spi-nand: spi_nand nand@0: 256 MiB, block size: 128 KiB, page size: 2048, OOB size: 128 ubi0 error: init_volumes: not enough PEBs, required 1699, available 915 ubi0 error: ubi_wl_init: no enough physical eraseblocks (-784, need 1) ubi0 error: ubi_attach_mtd_dev: failed to attach mtd5, error -12 UBI error: cannot attach mtd5 UBI error: cannot initialize UBI, error -12 UBI init error 12 Please check, if the correct MTD partition is used (size big enough?) ** Cannot find mtd partition "ubi" In: serial Out: serial Err: serial Net: Warning: ethernet@1fb50000 (eth0) using random MAC address - ea:c0:0c:00:6c:6d eth0: ethernet@1fb50000 Hit any key to stop autoboot: 3  0 U-Boot>      setenv seri           bootm       tftpboot x cx0 40.bi     30.bin Using ethernet@1fb50000 device TFTP from server 192.168.1.10; our IP address is 192.168.1.1 Filename 'cx30.bin'. Load address: 0x86a00000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# # 588.9 KiB/s done Bytes transferred = 23855104 (16c0000 hex) U-Boot> bootm ## Loading kernel (any) from FIT Image at 86a00000 ... Using 'config-1' configuration Trying 'kernel-1' kernel subimage Description: ARM OpenWrt Linux-6.12.87 Type: Kernel Image Compression: lzma compressed Data Start: 0x86a000e4 Data Size: 23772560 Bytes = 22.7 MiB Architecture: ARM OS: Linux Load Address: 0x80208000 Entry Point: 0x80208000 Hash algo: crc32 Hash value: 977c9243 Hash algo: sha1 Hash value: 8c1bb3ce824bac6b01b2617411c835da745b42ed Verifying Hash Integrity ... crc32+ sha1+ OK ## Loading fdt (any) from FIT Image at 86a00000 ... Using 'config-1' configuration Trying 'fdt-1' fdt subimage Description: ARM OpenWrt genexis_cx30 device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x880abfac Data Size: 13933 Bytes = 13.6 KiB Architecture: ARM Hash algo: crc32 Hash value: 2d07ba76 Hash algo: sha1 Hash value: 11ef3efa883fa7f5829406fcf97463e0bc540a57 Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x880abfac Working FDT set to 880abfac Uncompressing Kernel Image to 80208000 Loading Device Tree to 9eb1e000, end 9eb2466c ... OK Working FDT set to 9eb1e000 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.12.87 (sirherobrine23@matheus-note) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 14.3.0 r33479-5f7ec5c8b9) 14.3.0, GNU ld (GNU Binutils) 2.44) #0 SMP Sat May 9 15:26:26 2026 [ 0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Heimgard/Genexis CX30 [ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000 [ 0.000000] earlycon: ns16550 at MMIO32 0x1fbf0000 (options '115200n8') [ 0.000000] printk: legacy bootconsole [ns16550] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080200000-0x000000009fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080200000-0x0000000083ffffff] [ 0.000000] node 0: [mem 0x0000000084000000-0x00000000844fffff] [ 0.000000] node 0: [mem 0x0000000084500000-0x00000000848fffff] [ 0.000000] node 0: [mem 0x0000000084900000-0x00000000862fffff] [ 0.000000] node 0: [mem 0x0000000086300000-0x000000009fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x000000009fffffff] [ 0.000000] On node 0, zone Normal: 512 pages in unavailable ranges [ 0.000000] OF: reserved mem: 0x80000000..0x8003ffff (256 KiB) nomap non-reusable atf@80000000 [ 0.000000] OF: reserved mem: 0x84000000..0x840fffff (1024 KiB) nomap non-reusable npu_binary@84000000 [ 0.000000] OF: reserved mem: 0x84100000..0x844fffff (4096 KiB) nomap non-reusable qdma0-buf@84100000 [ 0.000000] OF: reserved mem: 0x84900000..0x84cfffff (4096 KiB) nomap non-reusable qdma1-buf@84900000 [ 0.000000] OF: reserved mem: 0x84d00000..0x862fffff (22528 KiB) nomap non-reusable npu-pkt@84d00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 14 pages/cpu s25228 r8192 d23924 u57344 [ 0.000000] Kernel command line: console=ttyS0,115200 earlycon [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130560 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=2. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GICv3: 256 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: GICv3 features: 16 PPIs [ 0.000000] GICv3: GICD_CTRL.DS=0, SCR_EL3.FIQ=0 [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x09080000 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns [ 0.000001] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns [ 0.008800] Switching to timer-based delay loop, resolution 40ns [ 0.015561] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000) [ 0.026948] CPU: Testing write buffer coherency: ok [ 0.032341] pid_max: default: 32768 minimum: 301 [ 0.044067] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.052119] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.063646] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.070877] Setting up static identity map for 0x80300000 - 0x80300060 [ 0.078226] rcu: Hierarchical SRCU implementation. [ 0.083494] rcu: Max phase no-delay instances is 1000. [ 0.089507] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 0.098694] smp: Bringing up secondary CPUs ... [ 0.118746] GICv3: CPU1: found redistributor 1 region 0:0x090a0000 [ 0.118800] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.118947] smp: Brought up 1 node, 2 CPUs [ 0.136455] SMP: Total of 2 processors activated (100.00 BogoMIPS). [ 0.143355] CPU: All CPU(s) started in SVC mode. [ 0.148917] Memory: 452592K/522240K available (7695K kernel code, 622K rwdata, 2020K rodata, 20480K init, 217K bss, 68516K reserved, 0K cma-reserved) [ 0.167884] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.178758] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.189656] pinctrl core: initialized pinctrl subsystem [ 0.197410] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.204218] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.212574] thermal_sys: Registered thermal governor 'step_wise' [ 0.212661] cpuidle: using governor menu [ 0.226224] /pcie@1fa91000: Fixed dependency cycle(s) with /pcie@1fa91000/interrupt-controller [ 0.236182] /pcie@1fa92000: Fixed dependency cycle(s) with /pcie@1fa92000/interrupt-controller [ 0.254392] SCSI subsystem initialized [ 0.258779] usbcore: registered new interface driver usbfs [ 0.264864] usbcore: registered new interface driver hub [ 0.270800] usbcore: registered new device driver usb [ 0.277720] clocksource: Switched to clocksource arch_sys_counter [ 0.290487] NET: Registered PF_INET protocol family [ 0.295995] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.304841] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.314098] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.322632] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.331189] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.339152] TCP: Hash tables configured (established 4096 bind 4096) [ 0.346431] MPTCP token hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.354643] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.361860] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.369958] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.376214] PCI: CLS 0 bytes, default 64 [ 0.382008] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.390782] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.397205] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.691410] mtk-pcie 1fa91000.pcie: host bridge /pcie@1fa91000 ranges: [ 0.698725] mtk-pcie 1fa91000.pcie: MEM 0x0020000000..0x0021ffffff -> 0x0020000000 [ 1.226319] mtk-pcie 1fa91000.pcie: PCI host bridge to bus 0000:00 [ 1.233186] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.239254] pci_bus 0000:00: root bus resource [mem 0x20000000-0x21ffffff] [ 1.247020] pci 0000:00:00.0: [14c3:0810] type 01 class 0x060400 PCIe Root Port [ 1.255289] pci 0000:00:00.0: BAR 0: can't handle BAR larger than 4GB (size 0x200000000) [ 1.264197] pci 0000:00:00.0: BAR 0 [mem size 0x00000001 64bit pref disabled] [ 1.272118] pci 0000:00:00.0: PCI bridge to [bus 00] [ 1.277729] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff] [ 1.287361] PCI: bus0: Fast back to back transfers disabled [ 1.293560] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.303025] pci 0000:01:00.0: [14c3:790a] type 00 class 0x028000 PCIe Endpoint [ 1.311183] pci 0000:01:00.0: BAR 0 [mem 0x00000000-0x000fffff 64bit pref] [ 1.318861] pci 0000:01:00.0: BAR 2 [mem 0x00000000-0x00007fff 64bit] [ 1.326035] pci 0000:01:00.0: BAR 4 [mem 0x00000000-0x00000fff 64bit pref] [ 1.334347] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 1.341451] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link) [ 1.358469] PCI: bus1: Fast back to back transfers disabled [ 1.364603] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 1.371974] pci 0000:00:00.0: bridge window [mem 0x20000000-0x201fffff]: assigned [ 1.380221] pci 0000:00:00.0: BAR 0 [mem 0x20200000 64bit pref disabled]: assigned [ 1.388602] pci 0000:00:00.0: BAR 0: error updating (0x2020000c != 0x0000000c) [ 1.396584] pci 0000:01:00.0: BAR 0 [mem 0x20000000-0x200fffff 64bit pref]: assigned [ 1.405202] pci 0000:01:00.0: BAR 2 [mem 0x20100000-0x20107fff 64bit]: assigned [ 1.413338] pci 0000:01:00.0: BAR 4 [mem 0x20108000-0x20108fff 64bit pref]: assigned [ 1.421940] pci 0000:00:00.0: PCI bridge to [bus 01] [ 1.427427] pci 0000:00:00.0: bridge window [mem 0x20000000-0x201fffff] [ 1.434982] pci_bus 0000:00: resource 4 [mem 0x20000000-0x21ffffff] [ 1.441892] pci_bus 0000:01: resource 1 [mem 0x20000000-0x201fffff] [ 1.449484] pcieport 0000:00:00.0: enabling device (0140 -> 0142) [ 1.456918] pcieport 0000:00:00.0: PME: Signaling with IRQ 30 [ 1.464861] mtk-pcie 1fa92000.pcie: host bridge /pcie@1fa92000 ranges: [ 1.472109] mtk-pcie 1fa92000.pcie: MEM 0x0022000000..0x0023ffffff -> 0x0022000000 [ 1.628595] mtk-pcie 1fa92000.pcie: PCI host bridge to bus 0001:00 [ 1.635404] pci_bus 0001:00: root bus resource [bus 00-ff] [ 1.641491] pci_bus 0001:00: root bus resource [mem 0x22000000-0x23ffffff] [ 1.649377] pci 0001:00:01.0: [14c3:0811] type 01 class 0x060400 PCIe Root Port [ 1.657592] pci 0001:00:01.0: BAR 0: can't handle BAR larger than 4GB (size 0x200000000) [ 1.666523] pci 0001:00:01.0: BAR 0 [mem size 0x00000001 64bit pref disabled] [ 1.674464] pci 0001:00:01.0: PCI bridge to [bus 00] [ 1.680004] pci 0001:00:01.0: bridge window [mem 0x00000000-0x000fffff] [ 1.689647] PCI: bus0: Fast back to back transfers disabled [ 1.695796] pci 0001:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.705312] pci 0001:01:00.0: [14c3:7906] type 00 class 0x028000 PCIe Endpoint [ 1.713515] pci 0001:01:00.0: BAR 0 [mem 0x00000000-0x000fffff 64bit pref] [ 1.721208] pci 0001:01:00.0: BAR 2 [mem 0x00000000-0x00007fff 64bit] [ 1.728412] pci 0001:01:00.0: BAR 4 [mem 0x00000000-0x00000fff 64bit pref] [ 1.736714] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold [ 1.743845] pci 0001:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0001:00:01.0 (capable of 8.000 Gb/s with 5.0 GT/s PCIe x2 link) [ 1.760907] PCI: bus1: Fast back to back transfers disabled [ 1.767041] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 [ 1.774412] pci 0001:00:01.0: bridge window [mem 0x22000000-0x221fffff]: assigned [ 1.782666] pci 0001:00:01.0: BAR 0 [mem 0x22200000 64bit pref disabled]: assigned [ 1.791049] pci 0001:00:01.0: BAR 0: error updating (0x2220000c != 0x0000000c) [ 1.799059] pci 0001:01:00.0: BAR 0 [mem 0x22000000-0x220fffff 64bit pref]: assigned [ 1.807671] pci 0001:01:00.0: BAR 2 [mem 0x22100000-0x22107fff 64bit]: assigned [ 1.815788] pci 0001:01:00.0: BAR 4 [mem 0x22108000-0x22108fff 64bit pref]: assigned [ 1.824388] pci 0001:00:01.0: PCI bridge to [bus 01] [ 1.829889] pci 0001:00:01.0: bridge window [mem 0x22000000-0x221fffff] [ 1.837418] pci_bus 0001:00: resource 4 [mem 0x22000000-0x23ffffff] [ 1.844325] pci_bus 0001:01: resource 1 [mem 0x22000000-0x221fffff] [ 1.851931] pcieport 0001:00:01.0: enabling device (0140 -> 0142) [ 1.859439] pcieport 0001:00:01.0: PME: Signaling with IRQ 32 [ 1.867636] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 1.875654] printk: legacy console [ttyS0] disabled [ 1.881500] 1fbf0000.serial: ttyS0 at MMIO 0x1fbf0000 (irq = 33, base_baud = 115200) is a 16550 [ 1.891171] printk: legacy console [ttyS0] enabled [ 1.891171] printk: legacy console [ttyS0] enabled [ 1.901249] printk: legacy bootconsole [ns16550] disabled [ 1.901249] printk: legacy bootconsole [ns16550] disabled [ 1.918462] random: crng init done [ 2.058526] airoha-spi 1fa10000.spi: boot type: NAND [ 2.064064] spi-nand spi0.0: Winbond SPI NAND was found. [ 2.069440] spi-nand spi0.0: 256 MiB, block size: 128 KiB, page size: 2048, OOB size: 128 [ 18.330786] 2 fixed-partitions partitions found on MTD device spi0.0 [ 18.337412] Creating 2 MTD partitions on "spi0.0": [ 18.342271] 0x000000000000-0x000000100000 : "u-boot" [ 18.350414] 0x000000100000-0x000010000000 : "ubi" [ 18.913482] ubi0: attaching mtd1 [ 20.003248] ubi0: scanning is finished [ 20.017132] ubi0: attached mtd1 (name "ubi", size 255 MiB) [ 20.022683] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 20.029574] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 20.036367] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 20.043340] ubi0: good PEBs: 2040, bad PEBs: 0, corrupted PEBs: 0 [ 20.049446] ubi0: user volume: 11, internal volumes: 1, max. volumes count: 128 [ 20.056757] ubi0: max/mean erase counter: 5/1, WL threshold: 4096, image sequence number: 702916436 [ 20.065816] ubi0: available PEBs: 299, total reserved PEBs: 1741, PEBs reserved for bad PEB handling: 40 [ 20.075330] ubi0: background thread "ubi_bgt0d" started, PID 155 [ 20.081423] spi_master spi0: cannot find modalias for /spi@1fa10000/flash@1 [ 20.088468] spi_master spi0: Failed to create SPI device for /spi@1fa10000/flash@1 [ 20.179888] airoha-npu 1e900000.npu: L2C sram: 0x00, FPGA Stage: 0 [ 21.147678] airoha-npu 1e900000.npu: wlan get msg: id 10, core 0, body size 4 [ 21.154844] airoha-npu 1e900000.npu: NPU not support get version [ 21.174726] mtk-eip93 1fb70000.crypto: EIP93:3:0:1,PE(0xfe007:0x41710041) [ 21.182018] NET: Registered PF_INET6 protocol family [ 21.188342] Segment Routing with IPv6 [ 21.192047] In-situ OAM (IOAM) with IPv6 [ 21.196040] NET: Registered PF_PACKET protocol family [ 21.201424] 8021q: 802.1Q VLAN Support v1.8 [ 21.205705] Registering SWP/SWPB emulation handler [ 21.282148] mt7530-mmio 1fb58000.switch: configuring for fixed/internal link mode [ 21.290000] mt7530-mmio 1fb58000.switch: Link is Up - 10Gbps/Full - flow control rx/tx [ 21.310620] mt7530-mmio 1fb58000.switch lan1 (uninitialized): PHY [mt7530-0:09] driver [Airoha AN7523 PHY] (irq=POLL) [ 21.322311] mt7530-mmio 1fb58000.switch lan2 (uninitialized): PHY [mt7530-0:0a] driver [Airoha AN7523 PHY] (irq=POLL) [ 21.333886] mt7530-mmio 1fb58000.switch wan (uninitialized): PHY [mt7530-0:0b] driver [Airoha AN7523 PHY] (irq=POLL) [ 21.345342] airoha_eth 1fb50000.ethernet eth0: entered promiscuous mode [ 21.352143] DSA: tree 0 setup [ 21.355975] clk: Disabling unused clocks [ 21.359986] PM: genpd: Disabling unused power domains [ 21.385861] Freeing unused kernel image (initmem) memory: 20480K [ 21.392203] Run /init as init process [ 22.046793] init: Console is alive [ 22.051509] init: - watchdog - [ 22.067151] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 22.083076] gpio_button_hotplug: loading out-of-tree module taints kernel. [ 22.106201] usbcore: registered new interface driver usb-storage [ 22.118608] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 22.136358] init: - preinit - Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 23.361210] procd: - early - [ 23.364242] procd: - watchdog - [ 23.900212] procd: - watchdog - [ 23.903913] procd: - ubus - [ 24.059418] procd: - init - Please press Enter to activate this console. [ 24.433698] kmodloader: loading kernel modules from /etc/modules.d/* [ 24.772099] i2c_dev: i2c /dev entries driver [ 24.784173] ntfs3: Enabled Linux POSIX ACLs support [ 24.796150] Loading modules backported from Linux version v6.18.26-0-g1fe060681 [ 24.803580] Backport generated by backports.git 6ecbb44 [ 24.864341] usbcore: registered new interface driver ums-alauda [ 24.875491] usbcore: registered new interface driver ums-cypress [ 24.883683] usbcore: registered new interface driver ums-datafab [ 24.891542] usbcore: registered new interface driver ums-freecom [ 24.902897] usbcore: registered new interface driver ums-isd200 [ 24.910849] usbcore: registered new interface driver ums-jumpshot [ 24.929596] usbcore: registered new interface driver ums-karma [ 24.936979] usbcore: registered new interface driver ums-sddr09 [ 24.958833] usbcore: registered new interface driver ums-sddr55 [ 24.966097] usbcore: registered new interface driver ums-usbat [ 25.045570] xt_time: kernel timezone is -0000 [ 25.234282] urngd: v1.0.2 started. [ 25.272838] mt7915e_hif 0000:01:00.0: enabling device (0140 -> 0142) [ 25.279683] mt7915e 0001:01:00.0: enabling device (0140 -> 0142) [ 25.487822] mt7915e 0001:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20240823172725a [ 25.519161] mt7915e 0001:01:00.0: WM Firmware Version: ____000000, Build Time: 20240823172741 [ 25.611109] mt7915e 0001:01:00.0: WA Firmware Version: DEV_000000, Build Time: 20240823172837 [ 25.748985] mt7915e 0001:01:00.0: registering led 'mt76-phy0' [ 25.827401] mt7915e 0001:01:00.0: registering led 'mt76-phy1' [ 25.950520] PPP generic driver version 2.4.2 [ 25.956056] NET: Registered PF_PPPOX protocol family [ 25.972510] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 25.980435] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld . All Rights Reserved. [ 26.012836] kmodloader: done loading kernel modules from /etc/modules.d/* BusyBox v1.37.0 (2026-01-02 17:07:02 UTC) built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt SNAPSHOT, r34374-359b1f13fb1 ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@OpenWrt:~# ifconfig[ 43.965558] br-lan: port 1(eth0) entered blocking state [ 43.970956] br-lan: port 1(eth0) entered disabled state [ 43.976293] airoha_eth 1fb50000.ethernet eth0: entered allmulticast mode [ 44.013307] br-lan: port 1(eth0) entered blocking state [ 44.018621] br-lan: port 1(eth0) entered forwarding state br-lan Link encap:Ethernet HWaddr 74:AF:93:E2:B0:DD inet addr:192.168.2.1 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::76af:93ff:fee2:b0dd/64 Scope:Link inet6 addr: fdc8:5673:e43f::1/60 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1504 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:386 (386.0 B) eth0 Link encap:Ethernet HWaddr 74:AF:93:E2:B0:DD UP BROADCAST RUNNING MULTICAST MTU:1504 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:2 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:208 (208.0 B) Interrupt:36 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) root@OpenWrt:~# ping 19ifconfig enobr-lan br-lan Link encap:Ethernet HWaddr 74:AF:93:E2:B0:DD inet addr:192.168.2.1 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::76af:93ff:fee2:b0dd/64 Scope:Link inet6 addr: fdc8:5673:e43f::1/60 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1504 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:10 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:1484 (1.4 KiB) root@OpenWrt:~# root@OpenWrt:~# ifconfig br-lan 19.12.168.1.1192.168.1.1 root@OpenWrt:~# ping 192.186.1.1068.1.10 PING 192.168.1.10 (192.168.1.10): 56 data bytes ^C --- 192.168.1.10 ping statistics --- 2 packets transmitted, 0 packets received, 100% packet loss root@OpenWrt:~# root@OpenWrt:~# ping 192.168.1.10 PING 192.168.1.10 (192.168.1.10): 56 data bytes ^C --- 192.168.1.10 ping statistics --- 2 packets transmitted, 0 packets received, 100% packet loss root@OpenWrt:~# ifconfig br-lan Link encap:Ethernet HWaddr 74:AF:93:E2:B0:DD inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::76af:93ff:fee2:b0dd/64 Scope:Link inet6 addr: fdc8:5673:e43f::1/60 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1504 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:14 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:1784 (1.7 KiB) eth0 Link encap:Ethernet HWaddr 74:AF:93:E2:B0:DD UP BROADCAST RUNNING MULTICAST MTU:1504 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:912 (912.0 B) Interrupt:36 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:84 errors:0 dropped:0 overruns:0 frame:0 TX packets:84 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:6688 (6.5 KiB) TX bytes:6688 (6.5 KiB) root@OpenWrt:~# dmesgping 192.168.4.1.100 PING 192.168.1.10 (192.168.1.10): 56 data bytes ^C --- 192.168.1.10 ping statistics --- 1 packets transmitted, 0 packets received, 100% packet loss root@OpenWrt:~# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.0 * 255.255.255.0 U 0 0 0 br-lan root@OpenWrt:~# root@OpenWrt:~# route root@OpenWrt:~# ping 192.168.1.10 PING 192.168.1.10 (192.168.1.10): 56 data bytes ^C --- 192.168.1.10 ping statistics --- 17 packets transmitted, 0 packets received, 100% packet loss root@OpenWrt:~# ifconfig br-lan Link encap:Ethernet HWaddr 74:AF:93:E2:B0:DD inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::76af:93ff:fee2:b0dd/64 Scope:Link inet6 addr: fdc8:5673:e43f::1/60 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1504 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:33 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:2846 (2.7 KiB) eth0 Link encap:Ethernet HWaddr 74:AF:93:E2:B0:DD UP BROADCAST RUNNING MULTICAST MTU:1504 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:27 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:1898 (1.8 KiB) Interrupt:36 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:213 errors:0 dropped:0 overruns:0 frame:0 TX packets:213 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:17328 (16.9 KiB) TX bytes:17328 (16.9 KiB) root@OpenWrt:~# dmes -ash: dmes: not found root@OpenWrt:~#