Secure key does not exist EN7523DRAMC V0.5 dram_type = 5, speed = 1866 Final Impdance Cal Result: OCDP:0x1b, OCDN:0x1e, ODTP:0x6, ODTN:0x6 DDR1866 PLL setting init [Dramc] PCDDR3 AC Timing update Fire MRW command... ModeReg.2, value.0x20 done Fire MRW command... ModeReg.3, value.0x0 done Fire MRW command... ModeReg.1, value.0x6 done Fire MRW command... ModeReg.0, value.0x1114 done Fire MRW command... ModeReg.1, value.0x86 done Fire MRW command... ModeReg.1, value.0x6 done Calculate size. DRAM size=512MB U-Boot 2026.01-OpenWrt-r34640+25-ae0da098a5d (May 27 2026 - 16:27:49 +0000) CPU: Airoha EN7523/EN7529/EN7562 Model: MikroTik E60iUGS (hEX S 2025) DRAM: 512 MiB Core: 21 devices, 16 uclasses, devicetree: separate Loading Environment from UBI... === WARNING ====================================================== Detected booting in RESERVED mode (UART_TXD was short to GND). This mode is known for incorrect DMA reading of some flashes. Usage of DMA for flash operations will be disabled to prevent data damage. Unplug your serial console and power cycle the board to boot with full performance. ================================================================== spi-nand: spi_nand nand@0: unknown raw ID 40 14 c8 40 Partition ubi not found! ** Cannot find mtd partition "ubi" In: serial Out: serial Err: serial Net: Warning: ethernet@1fb50000 (eth0) using random MAC address - 92:cc:df:c3:9c:c8 eth0: ethernet@1fb50000 Hit any key to stop autoboot: 3 Hit any key to stop autoboot: 0 U-Boot> tftpboot openwrt-airoha-en7523-mikrotik_e60iugs-initramfs-kernel.bin && bootm Using ethernet@1fb50000 device TFTP from server 192.168.1.10; our IP address is 192.168.1.1 Filename 'openwrt-airoha-en7523-mikrotik_e60iugs-initramfs-kernel.bin'. Load address: 0x86a00000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 11.8 MiB/s done Bytes transferred = 16355228 (f98f9c hex) ## Loading kernel (any) from FIT Image at 86a00000 ... Using 'config-1' configuration Trying 'kernel-1' kernel subimage Description: ARM OpenWrt Linux-6.18.34 Type: Kernel Image Compression: lzma compressed Data Start: 0x86a000e4 Data Size: 16335774 Bytes = 15.6 MiB Architecture: ARM OS: Linux Load Address: 0x80208000 Entry Point: 0x80208000 Hash algo: crc32 Hash value: 08635679 Hash algo: sha1 Hash value: c88d7ed0292402a92d10024713c84cdc908e60af Verifying Hash Integrity ... crc32+ sha1+ OK ## Loading fdt (any) from FIT Image at 86a00000 ... Using 'config-1' configuration Trying 'fdt-1' fdt subimage Description: ARM OpenWrt mikrotik_e60iugs device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x879945c0 Data Size: 18071 Bytes = 17.6 KiB Architecture: ARM Hash algo: crc32 Hash value: 92b893c5 Hash algo: sha1 Hash value: 2250ae1f4aea54df4c10c39c866013ac61756c8c Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x879945c0 Working FDT set to 879945c0 Uncompressing Kernel Image to 80208000 Loading Device Tree to 9eb1d000, end 9eb24696 ... OK Working FDT set to 9eb1d000 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.18.34 (sirherobrine23@matheus-note) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 14.3.0 r34771-7658a9ea318) 14.3.0, GNU ld (GNU Binutils) 2.44) #0 SMP Sun Jun 14 15:03:56 2026 [ 0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: MikroTik E60iUGS (hEX S 2025) [ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000 [ 0.000000] earlycon: ns16550 at MMIO32 0x1fbf0000 (options '115200n8') [ 0.000000] printk: legacy bootconsole [ns16550] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080200000-0x000000009fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080200000-0x0000000083ffffff] [ 0.000000] node 0: [mem 0x0000000084000000-0x00000000840fffff] [ 0.000000] node 0: [mem 0x0000000084100000-0x0000000084cfffff] [ 0.000000] node 0: [mem 0x0000000084d00000-0x00000000862fffff] [ 0.000000] node 0: [mem 0x0000000086300000-0x00000000863fffff] [ 0.000000] node 0: [mem 0x0000000086400000-0x00000000893fffff] [ 0.000000] node 0: [mem 0x0000000089400000-0x000000009fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x000000009fffffff] [ 0.000000] On node 0, zone Normal: 512 pages in unavailable ranges [ 0.000000] OF: reserved mem: 0x80000000..0x8003ffff (256 KiB) nomap non-reusable atf@80000000 [ 0.000000] OF: reserved mem: 0x84000000..0x840fffff (1024 KiB) nomap non-reusable npu-binary@84000000 [ 0.000000] OF: reserved mem: 0x84d00000..0x862fffff (22528 KiB) nomap non-reusable npu-pkt@84d00000 [ 0.000000] OF: reserved mem: 0x86400000..0x883fffff (32768 KiB) nomap non-reusable qdma0-buf@86400000 [ 0.000000] OF: reserved mem: 0x88400000..0x893fffff (16384 KiB) nomap non-reusable qdma1-buf@88400000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 14 pages/cpu s25356 r8192 d23796 u57344 [ 0.000000] Kernel command line: console=ttyS0,115200 earlycon [ 0.000000] printk: log buffer data + meta data: 131072 + 409600 = 540672 bytes [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130560 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=2. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GICv3: 256 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: GICv3 features: 16 PPIs [ 0.000000] GICv3: GICD_CTLR.DS=0, SCR_EL3.FIQ=0 [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x09080000 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 timer running at 25.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns [ 0.000001] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns [ 0.008801] Switching to timer-based delay loop, resolution 40ns [ 0.015594] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000) [ 0.026984] CPU: Testing write buffer coherency: ok [ 0.032376] pid_max: default: 32768 minimum: 301 [ 0.042742] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.050792] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.069188] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.076529] Setting up static identity map for 0x80300000 - 0x80300060 [ 0.083876] rcu: Hierarchical SRCU implementation. [ 0.089174] rcu: Max phase no-delay instances is 1000. [ 0.095192] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 0.104445] smp: Bringing up secondary CPUs ... [ 0.110033] GICv3: CPU1: found redistributor 1 region 0:0x090a0000 [ 0.110086] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.110324] smp: Brought up 1 node, 2 CPUs [ 0.127859] SMP: Total of 2 processors activated (100.00 BogoMIPS). [ 0.134744] CPU: All CPU(s) started in SVC mode. [ 0.140409] Memory: 418532K/522240K available (8569K kernel code, 628K rwdata, 2212K rodata, 12288K init, 215K bss, 102328K reserved, 0K cma-reserved) [ 0.160292] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.171160] posixtimers hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.179224] futex hash table entries: 512 (32768 bytes on 1 NUMA nodes, total 32 KiB, linear). [ 0.192214] pinctrl core: initialized pinctrl subsystem [ 0.200217] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.206979] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.215372] thermal_sys: Registered thermal governor 'step_wise' [ 0.215475] cpuidle: using governor menu [ 0.239643] SCSI subsystem initialized [ 0.243997] usbcore: registered new interface driver usbfs [ 0.250133] usbcore: registered new interface driver hub [ 0.256006] usbcore: registered new device driver usb [ 0.263018] clocksource: Switched to clocksource arch_sys_counter [ 0.275757] NET: Registered PF_INET protocol family [ 0.281273] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.290174] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.299424] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.307962] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.316518] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.324474] TCP: Hash tables configured (established 4096 bind 4096) [ 0.331766] MPTCP token hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.339989] UDP hash table entries: 256 (order: 2, 14336 bytes, linear) [ 0.347305] UDP-Lite hash table entries: 256 (order: 2, 14336 bytes, linear) [ 0.355532] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.361790] PCI: CLS 0 bytes, default 64 [ 0.367619] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.384070] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.390494] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. Warning : ecnt_avs_handler r1 not support [ 0.684238] airoha-cpu-pmdomain 1efbe000.cpufreq: ATF SMC not available, using direct PLL programming [ 0.694476] airoha-cpu-pmdomain 1efbe000.cpufreq: CPU frequency: 950 MHz, XTAL Clock 25 MHz [ 0.704661] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.712698] printk: legacy console [ttyS0] disabled [ 0.719911] 1fbf0000.serial: ttyS0 at MMIO 0x1fbf0000 (irq = 29, base_baud = 115200) is a 16550 [ 0.729578] printk: legacy console [ttyS0] enabled [ 0.729578] printk: legacy console [ttyS0] enabled [ 0.739650] printk: legacy bootconsole [ns16550] disabled [ 0.739650] printk: legacy bootconsole [ns16550] disabled [ 0.753778] random: crng init done [ 0.956589] airoha-spi 1fa10000.spi: boot type: NOR [ 0.961905] spi-nor spi0.0: supply vcc not found, using dummy regulator [ 11.442466] 2 fixed-partitions partitions found on MTD device spi0.0 [ 11.448897] Creating 2 MTD partitions on "spi0.0": [ 11.453723] 0x000000000000-0x0000000f0000 : "bootloader" [ 11.459912] 0x0000000f0000-0x000000100000 : "art" [ 11.466811] spi-nand spi0.1: unknown raw ID 4014c84014 [ 11.471959] spi-nand spi0.1: probe with driver spi-nand failed with error -95 [ 11.480373] generic-gpio-pse ethernet-pse: using pcdev.nr_lines=2 for PSE core FIFO workaround, real PIs=1 [ 11.490396] regulator regulator.1: supply vpwr not found, using dummy regulator [ 11.509097] airoha_eth 1fb50000.ethernet: generated random MAC address 92:bc:1e:4c:c9:70 [ 11.517470] airoha_eth 1fb50000.ethernet: generated random MAC address 2a:9e:43:f8:d9:05 [ 11.525777] airoha_eth 1fb50000.ethernet: generated random MAC address ae:ab:a7:c1:e9:66 [ 11.610405] airoha_eth 1fb50000.ethernet: Starting PPE Initialization [ 11.617645] airoha_eth 1fb50000.ethernet: Flushing 512 SRAM entries [ 11.626169] airoha_eth 1fb50000.ethernet: PPE Initialization completed successfully [ 11.633884] airoha_eth 1fb50000.ethernet: Setting CPU port for PPE 0, fport 1 to CDM1 [ 11.641719] airoha_eth 1fb50000.ethernet: Initializing UPD mem for port id 1 [ 11.649849] airoha_eth 1fb50000.ethernet: Setting CPU port for PPE 0, fport 2 to CDM2 [ 11.657770] airoha_eth 1fb50000.ethernet: Initializing UPD mem for port id 2 [ 11.665907] airoha_eth 1fb50000.ethernet: Setting CPU port for PPE 0, fport 3 to CDM1 [ 11.673852] airoha_eth 1fb50000.ethernet: eth2: wrong mac addr, MSBs must be 92:bc:1e [ 11.681701] airoha_eth 1fb50000.ethernet: FE hw forwarding won't work properly [C0]core freq at 333000000 Hz [C0]timer_init: Timer clk is running at 125 Mhz [C0]npu_gre_tunnel_tx_header_init L15 gre_tx_head_addr[0]=0x8400351c [C0]npu_gre_tunnel_tx_header_init L15 gre_tx_head_addr[1]=0x84003544 [C0][NPU] ba_node_init... [C0]baNode_array_init [C0]counter_init:2 [C0][NPU] queue_mutex_init... [C1]core1_main [C2]timer_isr Store Value 1e903000, val[C2]core2_main [C2]do npu_enq_deq_init [C3]core3_main [C3]core3_main for npu tunnel offload v21 [C3]npu bridge buf init sucess [ 12.234039] i2c-mt7621 1fbf8000.i2c0: clock 100 kHz [ 12.254422] inside-secure-eip93 1fb70000.crypto: EIP93:3:0:1,PE(0xfe007:0x41710041) [ 12.262758] NET: Registered PF_INET6 protocol family [ 12.269259] Segment Routing with IPv6 [ 12.272967] In-situ OAM (IOAM) with IPv6 [ 12.277058] NET: Registered PF_PACKET protocol family [ 12.282419] 8021q: 802.1Q VLAN Support v1.8 [ 12.286758] Registering SWP/SWPB emulation handler [ 12.304383] regulator-usb-vbus GPIO handle specifies active low - ignored [ 12.418802] mt7530-mmio 1fb58000.switch: configuring for fixed/internal link mode [ 12.426641] mt7530-mmio 1fb58000.switch lan2 (uninitialized): PHY [mt7530-0:09] driver [Airoha EN7523 PHY] (irq=POLL) [ 12.437360] mt7530-mmio 1fb58000.switch: Link is Up - 10Gbps/Full - flow control rx/tx [ 12.444702] mt7530-mmio 1fb58000.switch lan3 (uninitialized): PHY [mt7530-0:0a] driver [Airoha EN7523 PHY] (irq=POLL) [ 12.457688] mt7530-mmio 1fb58000.switch lan4 (uninitialized): PHY [mt7530-0:0b] driver [Airoha EN7523 PHY] (irq=POLL) [ 12.470220] mt7530-mmio 1fb58000.switch lan5 (uninitialized): PHY [mt7530-0:0c] driver [Airoha EN7523 PHY] (irq=POLL) [ 12.482517] airoha_eth 1fb50000.ethernet eth0: entered promiscuous mode [ 12.489306] DSA: tree 0 setup [ 12.492827] xhci-mtk 1fab0000.usb: supply vusb33 not found, using dummy regulator [ 12.514513] airoha-usb-phy 1fad0000.phy: Frequency not detected, using default SR calibration. [ 12.527743] xhci-mtk 1fab0000.usb: xHCI Host Controller [ 12.533099] xhci-mtk 1fab0000.usb: new USB bus registered, assigned bus number 1 [ 12.544495] xhci-mtk 1fab0000.usb: hcc params 0x01400f98 hci version 0x110 quirks 0x0000000000200010 [ 12.553739] xhci-mtk 1fab0000.usb: irq 45, io mem 0x1fab0000 [ 12.559570] xhci-mtk 1fab0000.usb: xHCI Host Controller [ 12.564851] xhci-mtk 1fab0000.usb: new USB bus registered, assigned bus number 2 [ 12.572267] xhci-mtk 1fab0000.usb: Host supports USB 3.2 Enhanced SuperSpeed [ 12.580114] hub 1-0:1.0: USB hub found [ 12.584070] hub 1-0:1.0: 2 ports detected [ 12.588867] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 12.597678] hub 2-0:1.0: USB hub found [ 12.601588] hub 2-0:1.0: 1 port detected [ 12.606988] clk: Disabling unused clocks [ 12.610941] PM: genpd: Disabling unused power domains [ 12.629137] Freeing unused kernel image (initmem) memory: 12288K [ 12.635573] Run /init as init process [ 13.245934] init: Console is alive [ 13.249642] init: - watchdog - [ 13.270542] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 13.287386] gpio_button_hotplug: loading out-of-tree module taints kernel. [ 13.320479] usbcore: registered new interface driver usb-storage [ 13.327215] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 13.337223] init: - preinit - [ 13.555994] airoha_eth 1fb50000.ethernet sfp: renamed from eth1 [ 13.566084] airoha_eth 1fb50000.ethernet wan: renamed from eth2 Cannot parse config file '/etc/fw_env.config': No such file or directory Failed to find NVMEM device [ 14.009372] airoha_eth 1fb50000.ethernet: Setting PPE 0 MTU for index 1 to 1504 [ 14.017646] mt7530-mmio 1fb58000.switch lan2: configuring for phy/internal link mode Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 16.153459] mt7530-mmio 1fb58000.switch lan2: Link is Up - 1Gbps/Full - flow control rx/tx - generating board file - [ 18.527247] mt7530-mmio 1fb58000.switch lan2: Link is Down [ 18.538522] procd: - early - [ 18.541552] procd: - watchdog - [ 19.073800] procd: - watchdog - [ 19.077715] procd: - ubus - [ 19.135842] procd: - init - Please press Enter to activate this console. [ 19.595034] kmodloader: loading kernel modules from /etc/modules.d/* [ 19.937943] i2c_dev: i2c /dev entries driver [ 19.949477] ntfs3: Enabled Linux POSIX ACLs support [ 19.957999] Loading modules backported from Linux version v6.18.26-0-g1fe060681 [ 19.965374] Backport generated by backports.git 6ecbb44 [ 20.078296] sfp sfp: Host maximum power 3.0W [ 20.098426] usbcore: registered new interface driver ums-alauda [ 20.115773] usbcore: registered new interface driver ums-cypress [ 20.123350] usbcore: registered new interface driver ums-datafab [ 20.130425] usbcore: registered new interface driver ums-freecom [ 20.150776] usbcore: registered new interface driver ums-isd200 [ 20.158217] usbcore: registered new interface driver ums-jumpshot [ 20.165738] usbcore: registered new interface driver ums-karma [ 20.173358] usbcore: registered new interface driver ums-sddr09 [ 20.180742] usbcore: registered new interface driver ums-sddr55 [ 20.204616] usbcore: registered new interface driver ums-usbat [ 20.226831] urngd: v1.0.2 started. [ 20.246751] xt_time: kernel timezone is -0000 [ 20.511189] PPP generic driver version 2.4.2 [ 20.545592] NET: Registered PF_PPPOX protocol family [ 20.603674] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 20.611559] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld . All Rights Reserved. [ 20.673382] kmodloader: done loading kernel modules from /etc/modules.d/* [ 43.327748] airoha_eth 1fb50000.ethernet: Setting PPE 0 MTU for index 1 to 1504 [ 43.342844] mt7530-mmio 1fb58000.switch lan2: configuring for phy/internal link mode [ 43.352125] mt7530-mmio 1fb58000.switch lan2: Link is Up - 1Gbps/Full - flow control rx/tx [ 43.360504] br-lan: port 1(lan2) entered blocking state [ 43.365874] br-lan: port 1(lan2) entered disabled state [ 43.371164] mt7530-mmio 1fb58000.switch lan2: entered allmulticast mode [ 43.377876] airoha_eth 1fb50000.ethernet eth0: entered allmulticast mode [ 43.384958] mt7530-mmio 1fb58000.switch lan2: entered promiscuous mode [ 43.401645] br-lan: port 1(lan2) entered blocking state [ 43.406970] br-lan: port 1(lan2) entered forwarding state [ 43.448931] mt7530-mmio 1fb58000.switch lan3: configuring for phy/internal link mode [ 43.464302] br-lan: port 2(lan3) entered blocking state [ 43.469600] br-lan: port 2(lan3) entered disabled state [ 43.475037] mt7530-mmio 1fb58000.switch lan3: entered allmulticast mode [ 43.482073] mt7530-mmio 1fb58000.switch lan3: entered promiscuous mode [ 43.510059] mt7530-mmio 1fb58000.switch lan4: configuring for phy/internal link mode [ 43.523491] br-lan: port 3(lan4) entered blocking state [ 43.528761] br-lan: port 3(lan4) entered disabled state [ 43.534218] mt7530-mmio 1fb58000.switch lan4: entered allmulticast mode [ 43.560647] mt7530-mmio 1fb58000.switch lan4: entered promiscuous mode [ 43.587293] mt7530-mmio 1fb58000.switch lan5: configuring for phy/internal link mode [ 43.602797] br-lan: port 4(lan5) entered blocking state [ 43.608146] br-lan: port 4(lan5) entered disabled state [ 43.613545] mt7530-mmio 1fb58000.switch lan5: entered allmulticast mode [ 43.625586] mt7530-mmio 1fb58000.switch lan5: entered promiscuous mode [ 44.713654] Airoha EN8801SC mt7530-0:00: EN8801S Version: 3 [ 45.763537] airoha_eth 1fb50000.ethernet wan: PHY [mt7530-0:00] driver [Airoha EN8801SC] (irq=POLL) [ 45.772875] airoha_eth 1fb50000.ethernet wan: configuring for inband/sgmii link mode [ 45.780868] airoha_eth 1fb50000.ethernet: Setting PPE 0 MTU for index 3 to 1500 [ 45.790244] br-wan: port 1(wan) entered blocking state [ 45.795490] br-wan: port 1(wan) entered disabled state [ 45.800681] airoha_eth 1fb50000.ethernet wan: entered allmulticast mode [ 45.807680] airoha_eth 1fb50000.ethernet wan: entered promiscuous mode [ 45.825832] airoha_eth 1fb50000.ethernet sfp: configuring for inband/2500base-x link mode [ 45.845237] airoha_eth 1fb50000.ethernet: Setting PPE 0 MTU for index 2 to 1500 [ 45.863410] br-wan: port 2(sfp) entered blocking state [ 45.868599] br-wan: port 2(sfp) entered disabled state [ 45.873885] airoha_eth 1fb50000.ethernet sfp: entered allmulticast mode [ 45.880788] airoha_eth 1fb50000.ethernet sfp: entered promiscuous mode [ 49.903108] airoha_eth 1fb50000.ethernet wan: Link is Up - 1Gbps/Full - flow control rx/tx [ 49.913426] br-wan: port 1(wan) entered blocking state [ 49.918599] br-wan: port 1(wan) entered forwarding state [ 57.941620] airoha_eth 1fb50000.ethernet: NPU not attached, setting up offload [ 57.949204] airoha_eth 1fb50000.ethernet: Setting up PPE offload [ 57.955291] airoha_eth 1fb50000.ethernet: Initializing PPE Hardware [ 57.961570] airoha_eth 1fb50000.ethernet: Configuring PPE 0: SRAM entries 7, DRAM entries 4, stats entries -95 [ 57.971639] airoha_eth 1fb50000.ethernet: EN7523 PPE0 SRAM size mismatch: wrote 7, read 6, TB_CFG=e670fffc [ 57.981365] airoha_eth 1fb50000.ethernet: Setting CPU port for PPE 0, fport 1 to CDM1 [ 57.989234] airoha_eth 1fb50000.ethernet: Setting PPE 0 MTU for index 1 to 1504 [ 57.996576] airoha_eth 1fb50000.ethernet: Setting CPU port for PPE 0, fport 2 to CDM2 [ 58.004442] airoha_eth 1fb50000.ethernet: Setting PPE 0 MTU for index 2 to 1500 [ 58.011762] airoha_eth 1fb50000.ethernet: Setting CPU port for PPE 0, fport 3 to CDM1 [ 58.019622] airoha_eth 1fb50000.ethernet: Setting PPE 0 MTU for index 3 to 1500 [ 58.053083] airoha_eth 1fb50000.ethernet: PPE offload setup completed successfully [ 64.871347] sfp sfp: EEPROM base structure checksum failure: 0x63 != 0xff [ 64.878212] sfp EE: 00000000: 03 04 07 00 00 00 01 20 40 04 00 03 0d 00 01 ff ....... @....... [ 64.886967] sfp EE: 00000010: 37 1b 00 01 ff ff ff ff ff ff ff ff ff ff ff ff 7............... [ 64.895714] sfp EE: 00000020: 20 20 20 20 00 00 00 00 53 46 51 ff ff ff ff ff ....SFQ..... [ 64.904479] sfp EE: 00000030: 20 21 ff ff ff ff ff ff ff ff ff ff ff ff ff ff !.............. [ 64.913327] sfp EE: 00000040: c0 26 dd c2 00 00 00 00 68 2c dd c2 00 00 00 00 .&......h,...... [ 64.922058] sfp EE: 00000050: 44 df 87 cb 40 d2 80 c1 40 23 95 df 00 a7 80 c2 D...@...@#...... [ 68.634488] sfp sfp: module removed [ 69.811334] sfp sfp: EEPROM base structure checksum failure: 0xcd != 0xff [ 69.818199] sfp EE: 00000000: 03 05 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ [ 69.826938] sfp EE: 00000010: 37 1b 00 00 4f 45 4d 20 20 20 20 20 20 21 ff ff 7...OEM !.. [ 69.835685] sfp EE: 00000020: 20 20 20 20 00 00 00 00 53 46 50 2d 47 45 2d 54 ....SFP-GE-T [ 69.844429] sfp EE: 00000030: 20 20 20 20 20 20 20 20 56 32 20 20 03 52 01 ff V2 .R.. [ 69.853174] sfp EE: 00000040: c0 26 dd c2 00 00 00 00 68 2c dd c2 00 00 00 00 .&......h,...... [ 69.861882] sfp EE: 00000050: 44 df 87 cb 40 d2 80 c1 40 23 95 df 00 a7 80 c2 D...@...@#...... [ 71.638993] sfp sfp: module removed [ 75.181506] sfp sfp: EEPROM base structure checksum failure: 0xfe != 0xff [ 75.188489] sfp EE: 00000000: 03 04 07 01 ff ff ff ff ff ff ff ff ff ff ff ff ................ [ 75.197303] sfp EE: 00000010: 37 1b 00 00 4f 45 4d 20 20 20 20 20 20 20 20 20 7...OEM [ 75.206067] sfp EE: 00000020: 20 20 20 21 ff ff ff ff ff ff ff ff ff ff ff ff !............ [ 75.214919] sfp EE: 00000030: 41 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff A............... [ 75.223652] sfp EE: 00000040: 00 c0 ad c2 00 b4 b5 c2 80 3b 9c c2 00 36 9c c2 .........;...6.. [ 75.232358] sfp EE: 00000050: 80 3b 9c c2 00 ef 9b c2 00 36 9c c2 50 a1 9d c2 .;.......6..P... [ 77.903292] sfp sfp: module removed [ 91.215403] sfp sfp: module OEM SFP-GE-T rev V2 sn 2211140134 dc 221114 [ 91.224823] airoha_eth 1fb50000.ethernet sfp: switched to inband/1000base-x link mode [ 91.255410] hwmon hwmon0: temp1_input not attached to any thermal zone [ 92.303149] airoha_eth 1fb50000.ethernet sfp: Link is Up - 1Gbps/Full - flow control off [ 92.311417] br-wan: port 2(sfp) entered blocking state [ 92.316637] br-wan: port 2(sfp) entered forwarding state [ 101.996635] airoha_eth 1fb50000.ethernet sfp: Link is Down [ 102.002636] sfp sfp: module removed [ 102.007483] br-wan: port 2(sfp) entered disabled state [ 112.893074] sfp sfp: please wait, module slow to respond [ 168.315504] sfp sfp: module HUAWEI MA5671A rev 0000 sn 48575443D5FB119D dc 181025 [ 168.324935] airoha_eth 1fb50000.ethernet sfp: switched to inband/2500base-x link mode [ 168.355175] hwmon hwmon0: temp1_input not attached to any thermal zone [ 803.599170] sfp sfp: module removed Secure key does not exist EN7523DRAMC V0.5 dram_type = 5, speed = 1866 Final Impdance Cal Result: OCDP:0x1b, OCDN:0x1e, ODTP:0x6, ODTN:0x6 DDR1866 PLL setting init [Dramc] PCDDR3 AC Timing update Fire MRW command... ModeReg.2, value.0x20 done Fire MRW command... ModeReg.3, value.0x0 done Fire MRW command... ModeReg.1, value.0x6 done Fire MRW command... ModeReg.0, value.0x1114 done Fire MRW command... ModeReg.1, value.0x86 done Fire MRW command... ModeReg.1, value.0x6 done Calculate size. DRAM size=512MB U-Boot 2026.01-OpenWrt-r34640+25-ae0da098a5d (May 27 2026 - 16:27:49 +0000) CPU: Airoha EN7523/EN7529/EN7562 Model: MikroTik E60iUGS (hEX S 2025) DRAM: 512 MiB Core: 21 devices, 16 uclasses, devicetree: separate Loading Environment from UBI... === WARNING ====================================================== Detected booting in RESERVED mode (UART_TXD was short to GND). This mode is known for incorrect DMA reading of some flashes. Usage of DMA for flash operations will be disabled to prevent data damage. Unplug your serial console and power cycle the board to boot with full performance. ================================================================== spi-nand: spi_nand nand@0: unknown raw ID 40 14 c8 40 Partition ubi not found! ** Cannot find mtd partition "ubi" In: serial Out: serial Err: serial Net: Warning: ethernet@1fb50000 (eth0) using random MAC address - 26:d6:4c:e8:7c:3b eth0: ethernet@1fb50000 Hit any key to stop autoboot: 3 Hit any key to stop autoboot: 0 U-Boot> tftpboot openwrt-airoha-en7523-mikrotik_e60iugs-initramfs-kernel.bin && bootm Using ethernet@1fb50000 device TFTP from server 192.168.1.10; our IP address is 192.168.1.1 Filename 'openwrt-airoha-en7523-mikrotik_e60iugs-initramfs-kernel.bin'. Load address: 0x86a00000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 1.4 MiB/s done Bytes transferred = 16354992 (f98eb0 hex) ## Loading kernel (any) from FIT Image at 86a00000 ... Using 'config-1' configuration Trying 'kernel-1' kernel subimage Description: ARM OpenWrt Linux-6.18.34 Type: Kernel Image Compression: lzma compressed Data Start: 0x86a000e4 Data Size: 16335540 Bytes = 15.6 MiB Architecture: ARM OS: Linux Load Address: 0x80208000 Entry Point: 0x80208000 Hash algo: crc32 Hash value: e70d7677 Hash algo: sha1 Hash value: 2e5199717d5d0dbfd33743f036dd4d10ab23a24a Verifying Hash Integrity ... crc32+ sha1+ OK ## Loading fdt (any) from FIT Image at 86a00000 ... Using 'config-1' configuration Trying 'fdt-1' fdt subimage Description: ARM OpenWrt mikrotik_e60iugs device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x879944d4 Data Size: 18071 Bytes = 17.6 KiB Architecture: ARM Hash algo: crc32 Hash value: 92b893c5 Hash algo: sha1 Hash value: 2250ae1f4aea54df4c10c39c866013ac61756c8c Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x879944d4 Working FDT set to 879944d4 Uncompressing Kernel Image to 80208000 Loading Device Tree to 9eb1d000, end 9eb24696 ... OK Working FDT set to 9eb1d000 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.18.34 (sirherobrine23@matheus-note) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 14.3.0 r34771-7658a9ea318) 14.3.0, GNU ld (GNU Binutils) 2.44) #0 SMP Sun Jun 14 15:03:56 2026 [ 0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: MikroTik E60iUGS (hEX S 2025) [ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000 [ 0.000000] earlycon: ns16550 at MMIO32 0x1fbf0000 (options '115200n8') [ 0.000000] printk: legacy bootconsole [ns16550] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080200000-0x000000009fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080200000-0x0000000083ffffff] [ 0.000000] node 0: [mem 0x0000000084000000-0x00000000840fffff] [ 0.000000] node 0: [mem 0x0000000084100000-0x0000000084cfffff] [ 0.000000] node 0: [mem 0x0000000084d00000-0x00000000862fffff] [ 0.000000] node 0: [mem 0x0000000086300000-0x00000000863fffff] [ 0.000000] node 0: [mem 0x0000000086400000-0x00000000893fffff] [ 0.000000] node 0: [mem 0x0000000089400000-0x000000009fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x000000009fffffff] [ 0.000000] On node 0, zone Normal: 512 pages in unavailable ranges [ 0.000000] OF: reserved mem: 0x80000000..0x8003ffff (256 KiB) nomap non-reusable atf@80000000 [ 0.000000] OF: reserved mem: 0x84000000..0x840fffff (1024 KiB) nomap non-reusable npu-binary@84000000 [ 0.000000] OF: reserved mem: 0x84d00000..0x862fffff (22528 KiB) nomap non-reusable npu-pkt@84d00000 [ 0.000000] OF: reserved mem: 0x86400000..0x883fffff (32768 KiB) nomap non-reusable qdma0-buf@86400000 [ 0.000000] OF: reserved mem: 0x88400000..0x893fffff (16384 KiB) nomap non-reusable qdma1-buf@88400000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 14 pages/cpu s25356 r8192 d23796 u57344 [ 0.000000] Kernel command line: console=ttyS0,115200 earlycon [ 0.000000] printk: log buffer data + meta data: 131072 + 409600 = 540672 bytes [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130560 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=2. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GICv3: 256 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: GICv3 features: 16 PPIs [ 0.000000] GICv3: GICD_CTLR.DS=0, SCR_EL3.FIQ=0 [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x09080000 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 timer running at 25.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns [ 0.000001] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns [ 0.008800] Switching to timer-based delay loop, resolution 40ns [ 0.015595] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000) [ 0.026984] CPU: Testing write buffer coherency: ok [ 0.032376] pid_max: default: 32768 minimum: 301 [ 0.042744] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.050791] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.069190] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.076497] Setting up static identity map for 0x80300000 - 0x80300060 [ 0.083841] rcu: Hierarchical SRCU implementation. [ 0.089141] rcu: Max phase no-delay instances is 1000. [ 0.095151] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 0.104397] smp: Bringing up secondary CPUs ... [ 0.109971] GICv3: CPU1: found redistributor 1 region 0:0x090a0000 [ 0.110024] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.110262] smp: Brought up 1 node, 2 CPUs [ 0.127798] SMP: Total of 2 processors activated (100.00 BogoMIPS). [ 0.134683] CPU: All CPU(s) started in SVC mode. [ 0.140341] Memory: 418532K/522240K available (8568K kernel code, 628K rwdata, 2212K rodata, 12288K init, 215K bss, 102328K reserved, 0K cma-reserved) [ 0.160128] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.171004] posixtimers hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.179069] futex hash table entries: 512 (32768 bytes on 1 NUMA nodes, total 32 KiB, linear). [ 0.192067] pinctrl core: initialized pinctrl subsystem [ 0.200065] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.206829] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.215223] thermal_sys: Registered thermal governor 'step_wise' [ 0.215324] cpuidle: using governor menu [ 0.239510] SCSI subsystem initialized [ 0.243865] usbcore: registered new interface driver usbfs [ 0.250001] usbcore: registered new interface driver hub [ 0.255876] usbcore: registered new device driver usb [ 0.262881] clocksource: Switched to clocksource arch_sys_counter [ 0.275627] NET: Registered PF_INET protocol family [ 0.281141] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.290044] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.299294] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.307833] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.316386] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.324344] TCP: Hash tables configured (established 4096 bind 4096) [ 0.331636] MPTCP token hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.339858] UDP hash table entries: 256 (order: 2, 14336 bytes, linear) [ 0.347175] UDP-Lite hash table entries: 256 (order: 2, 14336 bytes, linear) [ 0.355402] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.361658] PCI: CLS 0 bytes, default 64 [ 0.672117] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.691115] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.697605] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. Warning : ecnt_avs_handler r1 not support [ 0.973984] airoha-cpu-pmdomain 1efbe000.cpufreq: ATF SMC not available, using direct PLL programming [ 0.984237] airoha-cpu-pmdomain 1efbe000.cpufreq: CPU frequency: 950 MHz, XTAL Clock 25 MHz [ 0.994393] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 1.002426] printk: legacy console [ttyS0] disabled [ 1.009631] 1fbf0000.serial: ttyS0 at MMIO 0x1fbf0000 (irq = 29, base_baud = 115200) is a 16550 [ 1.019320] printk: legacy console [ttyS0] enabled [ 1.019320] printk: legacy console [ttyS0] enabled [ 1.029390] printk: legacy bootconsole [ns16550] disabled [ 1.029390] printk: legacy bootconsole [ns16550] disabled [ 1.043222] random: crng init done [ 1.249803] airoha-spi 1fa10000.spi: boot type: NOR [ 1.255257] spi-nor spi0.0: supply vcc not found, using dummy regulator [ 11.430380] 2 fixed-partitions partitions found on MTD device spi0.0 [ 11.436822] Creating 2 MTD partitions on "spi0.0": [ 11.441615] 0x000000000000-0x0000000f0000 : "bootloader" [ 11.447710] 0x0000000f0000-0x000000100000 : "art" [ 11.454499] spi-nand spi0.1: unknown raw ID 4014c84014 [ 11.459651] spi-nand spi0.1: probe with driver spi-nand failed with error -95 [ 11.468007] generic-gpio-pse ethernet-pse: using pcdev.nr_lines=2 for PSE core FIFO workaround, real PIs=1 [ 11.478058] regulator regulator.1: supply vpwr not found, using dummy regulator [ 11.497130] airoha_eth 1fb50000.ethernet: generated random MAC address 0a:69:fe:98:97:fb [ 11.505412] airoha_eth 1fb50000.ethernet: generated random MAC address 12:76:6d:32:ac:ab [ 11.513684] airoha_eth 1fb50000.ethernet: generated random MAC address 76:02:94:19:11:9b [ 11.590511] airoha_eth 1fb50000.ethernet: Starting PPE Initialization [ 11.597653] airoha_eth 1fb50000.ethernet: Flushing 512 SRAM entries [ 11.605771] airoha_eth 1fb50000.ethernet: PPE Initialization completed successfully [ 11.613493] airoha_eth 1fb50000.ethernet: Setting CPU port for PPE 0, fport 1 to CDM1 [ 11.621328] airoha_eth 1fb50000.ethernet: Initializing UPD mem for port id 1 [ 11.629460] airoha_eth 1fb50000.ethernet: Setting CPU port for PPE 0, fport 2 to CDM2 [ 11.637385] airoha_eth 1fb50000.ethernet: Initializing UPD mem for port id 2 [ 11.645526] airoha_eth 1fb50000.ethernet: Setting CPU port for PPE 0, fport 3 to CDM1 [ 11.653413] airoha_eth 1fb50000.ethernet: eth2: wrong mac addr, MSBs must be 0a:69:fe [ 11.661247] airoha_eth 1fb50000.ethernet: FE hw forwarding won't work properly [C0]core freq at 333000000 Hz [C0]timer_init: Timer clk is running at 125 Mhz [C0]npu_gre_tunnel_tx_header_init L15 gre_tx_head_addr[0]=0x8400351c [C0]npu_gre_tunnel_tx_header_init L15 gre_tx_head_addr[1]=0x84003544 [C0][NPU] ba_node_init... [C0]baNode_array_init [C0]counter_init:2 [C0][NPU] queue_mutex_init... [C1]core1_main [C2]timer_isr Store Value 1e903000, val[C2]core2_main [C2]do npu_enq_deq_init [C3]core3_main [C3]core3_main for npu tunnel offload v21 [C3]npu bridge buf init sucess [ 12.213834] i2c-mt7621 1fbf8000.i2c0: clock 100 kHz [ 12.234648] inside-secure-eip93 1fb70000.crypto: EIP93:3:0:1,PE(0xfe007:0x41710041) [ 12.243104] NET: Registered PF_INET6 protocol family [ 12.249752] Segment Routing with IPv6 [ 12.253526] In-situ OAM (IOAM) with IPv6 [ 12.257551] NET: Registered PF_PACKET protocol family [ 12.262966] 8021q: 802.1Q VLAN Support v1.8 [ 12.267264] Registering SWP/SWPB emulation handler [ 12.284917] regulator-usb-vbus GPIO handle specifies active low - ignored [ 12.400821] mt7530-mmio 1fb58000.switch: configuring for fixed/internal link mode [ 12.408670] mt7530-mmio 1fb58000.switch lan2 (uninitialized): PHY [mt7530-0:09] driver [Airoha EN7523 PHY] (irq=POLL) [ 12.419456] mt7530-mmio 1fb58000.switch: Link is Up - 10Gbps/Full - flow control rx/tx [ 12.424693] mt7530-mmio 1fb58000.switch lan3 (uninitialized): PHY [mt7530-0:0a] driver [Airoha EN7523 PHY] (irq=POLL) [ 12.439735] mt7530-mmio 1fb58000.switch lan4 (uninitialized): PHY [mt7530-0:0b] driver [Airoha EN7523 PHY] (irq=POLL) [ 12.452101] mt7530-mmio 1fb58000.switch lan5 (uninitialized): PHY [mt7530-0:0c] driver [Airoha EN7523 PHY] (irq=POLL) [ 12.464431] airoha_eth 1fb50000.ethernet eth0: entered promiscuous mode [ 12.471120] DSA: tree 0 setup [ 12.474688] xhci-mtk 1fab0000.usb: supply vusb33 not found, using dummy regulator [ 12.497552] airoha-usb-phy 1fad0000.phy: Frequency not detected, using default SR calibration. [ 12.510811] xhci-mtk 1fab0000.usb: xHCI Host Controller [ 12.516162] xhci-mtk 1fab0000.usb: new USB bus registered, assigned bus number 1 [ 12.527614] xhci-mtk 1fab0000.usb: hcc params 0x01400f98 hci version 0x110 quirks 0x0000000000200010 [ 12.536876] xhci-mtk 1fab0000.usb: irq 45, io mem 0x1fab0000 [ 12.542706] xhci-mtk 1fab0000.usb: xHCI Host Controller [ 12.548016] xhci-mtk 1fab0000.usb: new USB bus registered, assigned bus number 2 [ 12.555467] xhci-mtk 1fab0000.usb: Host supports USB 3.2 Enhanced SuperSpeed [ 12.563347] hub 1-0:1.0: USB hub found [ 12.567258] hub 1-0:1.0: 2 ports detected [ 12.572003] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 12.580792] hub 2-0:1.0: USB hub found [ 12.584670] hub 2-0:1.0: 1 port detected [ 12.590007] clk: Disabling unused clocks [ 12.594045] PM: genpd: Disabling unused power domains [ 12.611439] Freeing unused kernel image (initmem) memory: 12288K [ 12.619298] Run /init as init process [ 13.225906] init: Console is alive [ 13.229606] init: - watchdog - [ 13.251231] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 13.267985] gpio_button_hotplug: loading out-of-tree module taints kernel. [ 13.304514] usbcore: registered new interface driver usb-storage [ 13.311094] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 13.325492] init: - preinit - [ 13.553927] airoha_eth 1fb50000.ethernet sfp: renamed from eth1 [ 13.563711] airoha_eth 1fb50000.ethernet wan: renamed from eth2 Cannot parse config file '/etc/fw_env.config': No such file or directory Failed to find NVMEM device [ 14.005383] airoha_eth 1fb50000.ethernet: Setting PPE 0 MTU for index 1 to 2000 [ 14.013812] mt7530-mmio 1fb58000.switch lan2: configuring for phy/internal link mode Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 16.063275] mt7530-mmio 1fb58000.switch lan2: Link is Up - 1Gbps/Full - flow control rx/tx - generating board file - [ 18.507475] mt7530-mmio 1fb58000.switch lan2: Link is Down [ 18.519210] procd: - early - [ 18.522236] procd: - watchdog - [ 19.049215] procd: - watchdog - [ 19.053283] procd: - ubus - [ 19.112724] procd: - init - Please press Enter to activate this console. [ 19.560190] kmodloader: loading kernel modules from /etc/modules.d/* [ 19.946034] i2c_dev: i2c /dev entries driver [ 19.957293] ntfs3: Enabled Linux POSIX ACLs support [ 19.975958] Loading modules backported from Linux version v6.18.26-0-g1fe060681 [ 19.983335] Backport generated by backports.git 6ecbb44 [ 20.061347] sfp sfp: Host maximum power 3.0W [ 20.077705] usbcore: registered new interface driver ums-alauda [ 20.095060] usbcore: registered new interface driver ums-cypress [ 20.102472] usbcore: registered new interface driver ums-datafab [ 20.125438] usbcore: registered new interface driver ums-freecom [ 20.132624] usbcore: registered new interface driver ums-isd200 [ 20.155524] usbcore: registered new interface driver ums-jumpshot [ 20.162741] usbcore: registered new interface driver ums-karma [ 20.175153] usbcore: registered new interface driver ums-sddr09 [ 20.187380] usbcore: registered new interface driver ums-sddr55 [ 20.205044] usbcore: registered new interface driver ums-usbat [ 20.245775] xt_time: kernel timezone is -0000 [ 20.275986] urngd: v1.0.2 started. [ 20.446446] PPP generic driver version 2.4.2 [ 20.451951] NET: Registered PF_PPPOX protocol family [ 20.486163] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 20.494067] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld . All Rights Reserved. [ 20.563239] kmodloader: done loading kernel modules from /etc/modules.d/* [ 26.968158] airoha_eth 1fb50000.ethernet: Setting PPE 0 MTU for index 1 to 2000 [ 26.981561] mt7530-mmio 1fb58000.switch lan2: configuring for phy/internal link mode [ 26.998799] mt7530-mmio 1fb58000.switch lan2: Link is Up - 1Gbps/Full - flow control rx/tx [ 27.008287] br-lan: port 1(lan2) entered blocking state [ 27.013702] br-lan: port 1(lan2) entered disabled state [ 27.018991] mt7530-mmio 1fb58000.switch lan2: entered allmulticast mode [ 27.025683] airoha_eth 1fb50000.ethernet eth0: entered allmulticast mode [ 27.032944] mt7530-mmio 1fb58000.switch lan2: entered promiscuous mode [ 27.045455] br-lan: port 1(lan2) entered blocking state [ 27.050765] br-lan: port 1(lan2) entered forwarding state [ 27.076671] mt7530-mmio 1fb58000.switch lan3: configuring for phy/internal link mode [ 27.087856] br-lan: port 2(lan3) entered blocking state [ 27.093197] br-lan: port 2(lan3) entered disabled state [ 27.098491] mt7530-mmio 1fb58000.switch lan3: entered allmulticast mode [ 27.105531] mt7530-mmio 1fb58000.switch lan3: entered promiscuous mode [ 27.118128] mt7530-mmio 1fb58000.switch lan4: configuring for phy/internal link mode [ 27.127709] br-lan: port 3(lan4) entered blocking state [ 27.133022] br-lan: port 3(lan4) entered disabled state [ 27.138331] mt7530-mmio 1fb58000.switch lan4: entered allmulticast mode [ 27.149727] mt7530-mmio 1fb58000.switch lan4: entered promiscuous mode [ 27.184877] mt7530-mmio 1fb58000.switch lan5: configuring for phy/internal link mode [ 27.200698] br-lan: port 4(lan5) entered blocking state [ 27.206096] br-lan: port 4(lan5) entered disabled state [ 27.211396] mt7530-mmio 1fb58000.switch lan5: entered allmulticast mode [ 27.220011] mt7530-mmio 1fb58000.switch lan5: entered promiscuous mode [ 28.303685] Airoha EN8801SC mt7530-0:00: EN8801S Version: 3 [ 29.374059] airoha_eth 1fb50000.ethernet wan: PHY [mt7530-0:00] driver [Airoha EN8801SC] (irq=POLL) [ 29.385311] airoha_eth 1fb50000.ethernet wan: configuring for inband/sgmii link mode [ 29.394300] airoha_eth 1fb50000.ethernet: Setting PPE 0 MTU for index 3 to 2000 [ 29.403949] br-wan: port 1(wan) entered blocking state [ 29.409128] br-wan: port 1(wan) entered disabled state [ 29.414419] airoha_eth 1fb50000.ethernet wan: entered allmulticast mode [ 29.422165] airoha_eth 1fb50000.ethernet wan: entered promiscuous mode [ 29.439006] airoha_eth 1fb50000.ethernet sfp: configuring for inband/2500base-x link mode [ 29.458459] airoha_eth 1fb50000.ethernet: Setting PPE 0 MTU for index 2 to 2000 [ 29.490425] br-wan: port 2(sfp) entered blocking state [ 29.495694] br-wan: port 2(sfp) entered disabled state [ 29.500915] airoha_eth 1fb50000.ethernet sfp: entered allmulticast mode [ 29.507863] airoha_eth 1fb50000.ethernet sfp: entered promiscuous mode [ 33.582946] airoha_eth 1fb50000.ethernet wan: Link is Up - 1Gbps/Full - flow control rx/tx [ 33.592958] br-wan: port 1(wan) entered blocking state [ 33.598141] br-wan: port 1(wan) entered forwarding state [ 39.771279] airoha_eth 1fb50000.ethernet: NPU not attached, setting up offload [ 39.778836] airoha_eth 1fb50000.ethernet: Setting up PPE offload [ 39.784958] airoha_eth 1fb50000.ethernet: Initializing PPE Hardware [ 39.791243] airoha_eth 1fb50000.ethernet: Configuring PPE 0: SRAM entries 7, DRAM entries 4, stats entries -95 [ 39.801296] airoha_eth 1fb50000.ethernet: EN7523 PPE0 SRAM size mismatch: wrote 7, read 6, TB_CFG=e670fffc [ 39.811011] airoha_eth 1fb50000.ethernet: Setting CPU port for PPE 0, fport 1 to CDM1 [ 39.818941] airoha_eth 1fb50000.ethernet: Setting PPE 0 MTU for index 1 to 2000 [ 39.826323] airoha_eth 1fb50000.ethernet: Setting CPU port for PPE 0, fport 2 to CDM2 [ 39.834254] airoha_eth 1fb50000.ethernet: Setting PPE 0 MTU for index 2 to 2000 [ 39.841592] airoha_eth 1fb50000.ethernet: Setting CPU port for PPE 0, fport 3 to CDM1 [ 39.849547] airoha_eth 1fb50000.ethernet: Setting PPE 0 MTU for index 3 to 2000 [ 39.872965] airoha_eth 1fb50000.ethernet: PPE offload setup completed successfully [ 44.944175] mt7530-mmio 1fb58000.switch lan2: Link is Down [ 44.951080] br-lan: port 1(lan2) entered disabled state [ 48.064307] mt7530-mmio 1fb58000.switch lan2: Link is Up - 1Gbps/Full - flow control rx/tx [ 48.073537] br-lan: port 1(lan2) entered blocking state [ 48.078800] br-lan: port 1(lan2) entered forwarding state c