Sirherobrine23/openwrt_mitrastar
1
0
Fork 0
forked from Openwrt-EcoNet/openwrt
Code Pull Requests Activity
Files
new-platform-econet-jun4
openwrt_mitrastar/target/linux/qualcommax/image/ipq60xx.mk
Piotr Dymacz 35c828c168 ipq60xx: add support for ALFA Network AP120C-AX 
ALFA Network AP120C-AX is a dual-band ceiling AP, based on Qualcomm
IPQ6000 + QCN5021 + QCN5052 + QCA8072 chipsets bundle.

Specifications:

- SOC:      Qualcomm IPQ6000 (quad-core Cortex-A53 1.2 GHz)
- DRAM:     DDR3 512 MB (Micron MT41K256M16TW-107)
- Flash:    16 MB SPI NOR (Macronix MX25U12832F, boot device)
            128 MB NAND (Macronix MX30UF1G18AC, dual-firmware)
- Ethernet: 2x 10/100/1000 Mbps Ethernet (QCA8072)
            802.3at/af PoE input in WAN port
- Wi-Fi:    2x2 2.4 GHz Wi-Fi 6 (QCN5021 + RFFM8227 FEM)
            2x2   5 GHz Wi-Fi 6 (QCN5152 + QPF4568 FEM)
- Antenna:  for indoor version: dual-band, internal
            2x (or 4x) U.FL antenna connectors on the PCB
- LED:      for indoor/outdoor versions: 5x on external module (status,
            2x Wi-Fi, 2x Ethernet), PoE LED on-board
            8-pin on-board header for LED module (1.27 mm pitch, J14)
- Button:   1x button (reset)
- USB:      1x 4-pin on-board header for USB 2.0 (2.54 mm pitch, J22)
- UART:     1x micro USB Type-B for system console (Holtek HT42B534)
            1x 4-pin on-board header (2.54 mm pitch, J11)
- Power:    802.3at/af PoE or 12 V DC/2 A (DC jack)
- Other:    8-pin and 4-pin on-board headers for external Bluetooth
            module (1.27 mm pitch, J15, J16, unavailable, thus untested)

MAC addresses:

- WAN:               00:c0:ca:xx:xx:6c (art 0x0, device's label -2)
- LAN:               00:c0:ca:xx:xx:6d (art 0x6, device's label -1)
- 2.4 GHz (IPQ6000): 00:c0:ca:xx:xx:6e (art 0xc, device's label)
-   5 GHz (IPQ6000): 00:c0:ca:xx:xx:6f (device's label + 1)

Flash instructions:

Due to the lack of direct GUI based update capability and dual-firmware
partition configuration, it is recommended to use TFTP + serial console
based approach (console is available in micro USB connector):

1. Set a static IP 192.168.1.1/24 on PC and start TFTP server with the
   '...-factory.ubi' image renamed to 'firmware.bin'.
2. Make sure you can access board's serial console over micro USB.
3. Power up the device, hit any key to enter U-Boot CLI and issue below
   commands.

3.1 Restore U-Boot's environment to default values (double check first
    the '0:APPSBLENV' partition offset using 'smem' command):

    sf probe
    sf erase 0x510000 0x10000
    saveenv

3.2 Download and install OpenWrt in both partitions and reset the board:

    tftpb 0x44000000 firmware.bin
    flash rootfs
    flash rootfs_1
    reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2025-05-27 23:43:55 +02:00

232 lines
6.3 KiB
Makefile
Raw Permalink Blame History

DEVICE_VARS += TPLINK_SUPPORT_STRING
define Build/wax610-netgear-tar
mkdir $@.tmp
mv $@ $@.tmp/nand-ipq6018-apps.img
md5sum $@.tmp/nand-ipq6018-apps.img | cut -c 1-32 > $@.tmp/nand-ipq6018-apps.md5sum
echo "WAX610" > $@.tmp/metadata.txt
echo "WAX610-610Y_V99.9.9.9" > $@.tmp/version
tar -C $@.tmp/ -cf $@ .
rm -rf $@.tmp
endef
define Device/8devices_mango-dvk
$(call Device/FitImageLzma)
DEVICE_VENDOR := 8devices
DEVICE_MODEL := Mango-DVK
IMAGE_SIZE := 27776k
BLOCKSIZE := 64k
SOC := ipq6010
SUPPORTED_DEVICES += 8devices,mango
IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | append-rootfs | pad-rootfs | check-size | append-metadata
DEVICE_PACKAGES := ipq-wifi-8devices_mango
endef
TARGET_DEVICES += 8devices_mango-dvk
define Device/alfa-network_ap120c-ax
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := ALFA Network
DEVICE_MODEL := AP120C-AX
BLOCKSIZE := 128k
PAGESIZE := 2048
SOC := ipq6000
DEVICE_PACKAGES := ipq-wifi-alfa-network_ap120c-ax
endef
TARGET_DEVICES += alfa-network_ap120c-ax
define Device/cambiumnetworks_xe3-4
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Cambium Networks
DEVICE_MODEL := XE3-4
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS_CONFIG := config@cp01-c3-xv3-4
SOC := ipq6010
DEVICE_PACKAGES := ipq-wifi-cambiumnetworks_xe34 ath11k-firmware-qcn9074 kmod-ath11k-pci
endef
TARGET_DEVICES += cambiumnetworks_xe3-4
define Device/glinet_gl-common
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := GL.iNet
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS_CONFIG := config@cp03-c1
SOC := ipq6000
IMAGES += factory.bin
IMAGE/factory.bin := append-ubi | append-gl-metadata
endef
define Device/glinet_gl-ax1800
$(call Device/glinet_gl-common)
DEVICE_MODEL := GL-AX1800
DEVICE_PACKAGES := ipq-wifi-glinet_gl-ax1800
SUPPORTED_DEVICES += glinet,ax1800
endef
TARGET_DEVICES += glinet_gl-ax1800
define Device/glinet_gl-axt1800
$(call Device/glinet_gl-common)
DEVICE_MODEL := GL-AXT1800
DEVICE_PACKAGES := ipq-wifi-glinet_gl-axt1800 kmod-hwmon-pwmfan
SUPPORTED_DEVICES += glinet,axt1800
endef
TARGET_DEVICES += glinet_gl-axt1800
define Device/linksys_mr
$(call Device/FitImage)
DEVICE_VENDOR := Linksys
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 8192k
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=$$$$(DEVICE_MODEL)
DEVICE_PACKAGE := kmod-usb-ledtrig-usbport
endef
define Device/linksys_mr7350
$(call Device/linksys_mr)
DEVICE_MODEL := MR7350
NAND_SIZE := 256m
IMAGE_SIZE := 75776k
SOC := ipq6000
DEVICE_PACKAGES += ipq-wifi-linksys_mr7350 kmod-leds-pca963x
endef
TARGET_DEVICES += linksys_mr7350
define Device/linksys_mr7500
$(call Device/linksys_mr)
DEVICE_MODEL := MR7500
SOC := ipq6018
NAND_SIZE := 512m
IMAGE_SIZE := 147456k
DEVICE_PACKAGES += ipq-wifi-linksys_mr7500 \
ath11k-firmware-qcn9074 kmod-ath11k-pci \
kmod-leds-pwm kmod-phy-aquantia
endef
TARGET_DEVICES += linksys_mr7500
define Device/netgear_wax214
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Netgear
DEVICE_MODEL := WAX214
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS_CONFIG := config@cp03-c1
SOC := ipq6010
DEVICE_PACKAGES := ipq-wifi-netgear_wax214
endef
TARGET_DEVICES += netgear_wax214
define Device/netgear_wax610-common
$(call Device/FitImage)
DEVICE_VENDOR := Netgear
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS_CONFIG := config@cp03-c1
SOC := ipq6010
KERNEL_IN_UBI := 1
IMAGES += ui-factory.tar
IMAGE/ui-factory.tar := append-ubi | qsdk-ipq-factory-nand | pad-to 4096 | wax610-netgear-tar
endef
define Device/netgear_wax610
$(Device/netgear_wax610-common)
DEVICE_MODEL := WAX610
DEVICE_PACKAGES := ipq-wifi-netgear_wax610
endef
TARGET_DEVICES += netgear_wax610
define Device/netgear_wax610y
$(Device/netgear_wax610-common)
DEVICE_MODEL := WAX610Y
DEVICE_PACKAGES := ipq-wifi-netgear_wax610y
endef
TARGET_DEVICES += netgear_wax610y
define Device/qihoo_360v6
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Qihoo
DEVICE_MODEL := 360V6
BLOCKSIZE := 128k
PAGESIZE := 2048
SOC := ipq6000
DEVICE_DTS_CONFIG := config@cp03-c1
DEVICE_PACKAGES := ipq-wifi-qihoo_360v6
endef
TARGET_DEVICES += qihoo_360v6
define Device/tplink_eap610-outdoor
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := TP-Link
DEVICE_MODEL := EAP610-Outdoor
BLOCKSIZE := 128k
PAGESIZE := 2048
SOC := ipq6018
DEVICE_PACKAGES := ipq-wifi-tplink_eap610-outdoor
IMAGES += web-ui-factory.bin
IMAGE/web-ui-factory.bin := append-ubi | tplink-image-2022
TPLINK_SUPPORT_STRING := SupportList:\r\n \
EAP610-Outdoor(TP-Link|UN|AX1800-D):1.0\r\n \
EAP610-Outdoor(TP-Link|JP|AX1800-D):1.0\r\n \
EAP610-Outdoor(TP-Link|CA|AX1800-D):1.0
endef
TARGET_DEVICES += tplink_eap610-outdoor
define Device/tplink_eap623od-hd-v1
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := TP-Link
DEVICE_MODEL := EAP623-Outdoor HD
DEVICE_VARIANT := v1
BLOCKSIZE := 128k
PAGESIZE := 2048
SOC := ipq6018
DEVICE_PACKAGES := ipq-wifi-tplink_eap623od-hd-v1 kmod-phy-realtek
IMAGES += web-ui-factory.bin
IMAGE/web-ui-factory.bin := append-ubi | tplink-image-2022
TPLINK_SUPPORT_STRING := SupportList:\r\nEAP623-Outdoor HD(TP-Link|UN|AX1800-D):1.0\r\n
endef
TARGET_DEVICES += tplink_eap623od-hd-v1
define Device/tplink_eap625-outdoor-hd-v1
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := TP-Link
DEVICE_MODEL := EAP625-Outdoor HD v1 and v1.6
BLOCKSIZE := 128k
PAGESIZE := 2048
SOC := ipq6018
DEVICE_PACKAGES := ipq-wifi-tplink_eap625-outdoor-hd-v1
IMAGES += web-ui-factory.bin
IMAGE/web-ui-factory.bin := append-ubi | tplink-image-2022
TPLINK_SUPPORT_STRING := SupportList:\r\n \
EAP625-Outdoor HD(TP-Link|UN|AX1800-D):1.0\r\n \
EAP625-Outdoor HD(TP-Link|CA|AX1800-D):1.0\r\n \
EAP625-Outdoor HD(TP-Link|AU|AX1800-D):1.0\r\n \
EAP625-Outdoor HD(TP-Link|KR|AX1800-D):1.0
endef
TARGET_DEVICES += tplink_eap625-outdoor-hd-v1
define Device/yuncore_fap650
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Yuncore
DEVICE_MODEL := FAP650
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS_CONFIG := config@cp03-c1
SOC := ipq6018
DEVICE_PACKAGES := ipq-wifi-yuncore_fap650
IMAGES := factory.ubi factory.ubin sysupgrade.bin
IMAGE/factory.ubin := append-ubi | qsdk-ipq-factory-nand
endef
TARGET_DEVICES += yuncore_fap650
View Git Blame Copy Permalink