forked from Openwrt-EcoNet/openwrt
50d9ca6e5a
Hardware -------- SOC: MediaTek MT7981b RAM: 256MB DDR3 FLASH: 128MB SPI-NAND (Winbond W25N01GV) WIFI: Mediatek MT7981b DBDC 802.11ax 2.4/5 GHz ETH: MediaTek MT7531 Switch UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC) Installation ----------------------------------------------------------- Vendor-UI Method ----------------------------------------------------------- 1. Download the OpenWrt initramfs.trx image. 2. Connect the PC via LAN to one of the yellow router ports and wait until your PC to get a DHCP lease. 3. Browse to http://192.168.50.1 4. If your router is brand new, finish the setup process and log into the Web-UI. 5. Navigate to Administration -> Firmware Upgrade and upload the downloaded OpenWrt image. 6. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using scp and install using sysupgrade. $ sysupgrade -n <path-to-sysupgrade.bin> ----------------------------------------------------------- TFTP Method ----------------------------------------------------------- 1. Download the OpenWrt initramfs image. Copy the image to a TFTP server reachable at 192.168.1.70/24. Rename the image to rtax52.bin. 2. Connect the PC with TFTP server to the RT-AX52. Set a static ip on the ethernet interface of your PC. (ip address: 192.168.1.70, subnet mask:255.255.255.0) Conect to the serial console, interrupt the autoboot process by pressing '4' when prompted. 3. Download & Boot the OpenWrt initramfs image. $ setenv ipaddr 192.168.1.1 $ setenv serverip 192.168.1.70 $ tftpboot 0x46000000 rtax52.bin $ bootm 0x46000000 4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using scp and install using sysupgrade. $ sysupgrade -n <path-to-sysupgrade.bin> --------------------------------------------------------------------------- Revert to stock firmware: 1: Download the rt-ax52 firmware from ASUS official website. Save the firmware to tftp server directory and rename to RT-AX52.trx 2: Connect the PC with TFTP server to the RT-AX52. Set a static ip on the ethernet interface of your PC. (ip address: 192.168.1.70, subnet mask:255.255.255.0) 3: Conect to the serial console, power on again, interrupt the autoboot process by pressing '4' when prompted. $: ubi remove linux $: ubi remove jffs2 $: ubi remove rootfs $: ubi remove rootfs_data $: ubi create linux 0x45fe000 $: reset Then the dut will reboot,interrupt the autoboot process by pressing '2' when prompted. 2: Load System code then write to Flash via TFTP. Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) $: enter y you will see the follow, type enter directly: Input device IP (192.168.1.1) ==: Input server IP (192.168.1.70) ==: Input Linux Kernel filename (RT-AX52.trx) ==: 4: wait for the device run up Based on support for ASUS RT-AX52 by liudongdongdong7397 and trx image generation by remittor Signed-off-by: Christoph Krapp <achterin@gmail.com>
49 lines
1.4 KiB
Makefile
49 lines
1.4 KiB
Makefile
# SPDX-License-Identifier: GPL-2.0-only
|
|
#
|
|
# Copyright (C) 2012-2015 OpenWrt.org
|
|
# Copyright (C) 2016-2017 LEDE project
|
|
|
|
include $(TOPDIR)/rules.mk
|
|
include $(INCLUDE_DIR)/image.mk
|
|
|
|
DEVICE_VARS += NETGEAR_ENC_MODEL NETGEAR_ENC_REGION NETGEAR_ENC_HW_ID_LIST NETGEAR_ENC_MODEL_LIST
|
|
|
|
loadaddr-$(CONFIG_TARGET_mediatek_mt7622) := 0x44000000
|
|
loadaddr-$(CONFIG_TARGET_mediatek_mt7623) := 0x80008000
|
|
loadaddr-$(CONFIG_TARGET_mediatek_mt7629) := 0x40008000
|
|
loadaddr-$(CONFIG_TARGET_mediatek_filogic) := 0x48000000
|
|
|
|
# default all platform image(fit) build
|
|
define Device/Default
|
|
PROFILES = Default $$(DEVICE_NAME)
|
|
KERNEL_NAME := Image
|
|
KERNEL = kernel-bin | lzma | \
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
KERNEL_INITRAMFS = kernel-bin | lzma | \
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd
|
|
KERNEL_LOADADDR = $(loadaddr-y)
|
|
FILESYSTEMS := squashfs
|
|
DEVICE_DTS_DIR := $(DTS_DIR)
|
|
NETGEAR_ENC_MODEL :=
|
|
NETGEAR_ENC_REGION :=
|
|
NETGEAR_ENC_HW_ID_LIST :=
|
|
NETGEAR_ENC_MODEL_LIST :=
|
|
IMAGES := sysupgrade.bin
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to 128k | append-rootfs | \
|
|
pad-rootfs | append-metadata
|
|
endef
|
|
|
|
define Build/asus-trx
|
|
$(STAGING_DIR_HOST)/bin/asusuimage $(wordlist 1,$(words $(1)),$(1)) -i $@ -o $@.new
|
|
mv $@.new $@
|
|
endef
|
|
|
|
include $(SUBTARGET).mk
|
|
|
|
define Image/Build
|
|
$(call Image/Build/$(1),$(1))
|
|
endef
|
|
|
|
$(eval $(call BuildImage))
|
|
|