ccf3cadcfc
Starting with kernel 4.4, the use of partitions as direct subnodes of the mtd device is discouraged and only supported for backward compatiblity reasons. Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 49280
230 lines
3.7 KiB
Plaintext
230 lines
3.7 KiB
Plaintext
/dts-v1/;
|
|
|
|
/include/ "danube.dtsi"
|
|
|
|
/ {
|
|
model = "ARV7519PW - Astoria Networks";
|
|
|
|
chosen {
|
|
bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
|
|
|
|
leds {
|
|
boot = &power;
|
|
failsafe = &power2;
|
|
running = &power;
|
|
|
|
dsl = &dsl;
|
|
internet = &online;
|
|
wifi = &wifi;
|
|
};
|
|
};
|
|
|
|
memory@0 {
|
|
reg = <0x0 0x4000000>;
|
|
};
|
|
|
|
sram@1F000000 {
|
|
vmmc@107000 {
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
fpi@10000000 {
|
|
localbus@0 {
|
|
nor-boot@0 {
|
|
compatible = "lantiq,nor";
|
|
bank-width = <2>;
|
|
reg = <0 0x0 0x2000000>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "uboot";
|
|
reg = <0x00000 0x40000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "uboot_env";
|
|
reg = <0x40000 0x20000>;
|
|
};
|
|
|
|
partition@60000 {
|
|
label = "firmware";
|
|
reg = <0x60000 0xf80000>;
|
|
};
|
|
|
|
partition@fe0000 {
|
|
label = "board_config";
|
|
reg = <0xfe0000 0x20000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
|
|
mac_addr {
|
|
compatible = "lantiq,eth-mac";
|
|
reg = <0 0xfe0016 0x6>;
|
|
mac-increment = <2>;
|
|
};
|
|
};
|
|
|
|
gpio: pinmux@E100B10 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&state_default>;
|
|
|
|
state_default: pinmux {
|
|
ebu {
|
|
lantiq,groups = "ebu cs1";
|
|
lantiq,function = "ebu";
|
|
};
|
|
pci_in {
|
|
lantiq,groups = "req1";
|
|
lantiq,function = "pci";
|
|
lantiq,open-drain = <1>;
|
|
lantiq,pull = <2>;
|
|
lantiq,output = <0>;
|
|
};
|
|
pci_out {
|
|
lantiq,groups = "gnt1";
|
|
lantiq,function = "pci";
|
|
lantiq,pull = <0>;
|
|
lantiq,output = <1>;
|
|
};
|
|
pci_rst {
|
|
lantiq,pins = "io21";
|
|
lantiq,pull = <2>;
|
|
lantiq,output = <1>;
|
|
};
|
|
switch_rst {
|
|
lantiq,pins = "io19";
|
|
lantiq,pull = <2>;
|
|
lantiq,output = <1>;
|
|
};
|
|
};
|
|
};
|
|
|
|
etop@E180000 {
|
|
phy-mode = "mii";
|
|
};
|
|
|
|
/* warning: passive port
|
|
only works with active devices */
|
|
ifxhcd@E101000 {
|
|
status = "okay";
|
|
};
|
|
|
|
pci@E105400 {
|
|
status = "okay";
|
|
lantiq,external-clock;
|
|
gpio-reset = <&gpio 21 0>;
|
|
req-mask = <0xf>;
|
|
};
|
|
};
|
|
|
|
ralink_eep {
|
|
compatible = "ralink,eeprom";
|
|
ralink,eeprom = "RT2860.eeprom";
|
|
};
|
|
|
|
gpio-keys-polled {
|
|
compatible = "gpio-keys-polled";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
poll-interval = <100>;
|
|
|
|
rfkill {
|
|
label = "rfkill";
|
|
gpios = <&gpio 11 1>;
|
|
linux,code = <0xf7>;
|
|
};
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio 28 1>;
|
|
linux,code = <0x198>;
|
|
};
|
|
};
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
power: power {
|
|
label = "power";
|
|
gpios = <&gpio 2 1>;
|
|
default-state = "keep";
|
|
};
|
|
power2: power2 {
|
|
label = "power2";
|
|
gpios = <&gpio 14 1>;
|
|
};
|
|
online: online {
|
|
label = "online";
|
|
gpios = <&gpio 3 1>;
|
|
};
|
|
online2 {
|
|
label = "online2";
|
|
gpios = <&gpio 30 1>;
|
|
};
|
|
wifi: wifi {
|
|
label = "wifi";
|
|
gpios = <&gpio 12 1>;
|
|
};
|
|
wifi2 {
|
|
label = "wifi2";
|
|
gpios = <&gpio 10 1>;
|
|
};
|
|
wifi3 {
|
|
label = "wifi3";
|
|
gpios = <&gpio 6 1>;
|
|
};
|
|
voice {
|
|
label = "voice";
|
|
gpios = <&gpio 31 1>;
|
|
};
|
|
wps {
|
|
label = "wps";
|
|
gpios = <&gpio 15 1>;
|
|
};
|
|
wps2 {
|
|
label = "wps2";
|
|
gpios = <&gpio 7 1>;
|
|
};
|
|
wps3 {
|
|
label = "wps3";
|
|
gpios = <&gpio 23 1>;
|
|
};
|
|
dsl: dsl {
|
|
label = "dsl";
|
|
gpios = <&gpio 4 1>;
|
|
};
|
|
lan {
|
|
label = "lan";
|
|
gpios = <&gpio 1 1>;
|
|
};
|
|
tv {
|
|
label = "tv";
|
|
gpios = <&gpio 20 1>;
|
|
};
|
|
upgrade {
|
|
label = "upgrade";
|
|
gpios = <&gpio 29 1>;
|
|
};
|
|
};
|
|
|
|
/* is there another way to "reserve" the GPIO? */
|
|
gpio_export {
|
|
compatible = "gpio-export";
|
|
#size-cells = <0>;
|
|
|
|
switch {
|
|
gpio-export,name = "switch";
|
|
gpio-export,output = <1>;
|
|
gpios = <&gpio 19 0>;
|
|
};
|
|
};
|
|
};
|