c05048b0bb
This adds support for the oxnas target in U-Boot 2014.04 History can be found at https://github.com/kref/u-boot-oxnas up to 2013.10 changes from 2013.10 to 2014.04 can be followed at https://gitorious.org/openwrt-oxnas Signed-off-by: Daniel Golle <daniel@makrotopia.org> SVN-Revision: 43389
478 lines
14 KiB
C
Executable File
478 lines
14 KiB
C
Executable File
/*******************************************************************
|
|
*
|
|
* File: ddr_oxsemi.c
|
|
*
|
|
* Description: Declarations for DDR routines and data objects
|
|
*
|
|
* Author: Julien Margetts
|
|
*
|
|
* Copyright: Oxford Semiconductor Ltd, 2009
|
|
*/
|
|
#include <common.h>
|
|
#include <asm/arch/clock.h>
|
|
|
|
#include "ddr.h"
|
|
|
|
typedef unsigned int UINT;
|
|
|
|
// DDR TIMING PARAMETERS
|
|
typedef struct {
|
|
unsigned int holdoff_cmd_A;
|
|
unsigned int holdoff_cmd_ARW;
|
|
unsigned int holdoff_cmd_N;
|
|
unsigned int holdoff_cmd_LM;
|
|
unsigned int holdoff_cmd_R;
|
|
unsigned int holdoff_cmd_W;
|
|
unsigned int holdoff_cmd_PC;
|
|
unsigned int holdoff_cmd_RF;
|
|
unsigned int holdoff_bank_R;
|
|
unsigned int holdoff_bank_W;
|
|
unsigned int holdoff_dir_RW;
|
|
unsigned int holdoff_dir_WR;
|
|
unsigned int holdoff_FAW;
|
|
unsigned int latency_CAS;
|
|
unsigned int latency_WL;
|
|
unsigned int recovery_WR;
|
|
unsigned int width_update;
|
|
unsigned int odt_offset;
|
|
unsigned int odt_drive_all;
|
|
unsigned int use_fixed_re;
|
|
unsigned int delay_wr_to_re;
|
|
unsigned int wr_slave_ratio;
|
|
unsigned int rd_slave_ratio0;
|
|
unsigned int rd_slave_ratio1;
|
|
} T_DDR_TIMING_PARAMETERS;
|
|
|
|
// DDR CONFIG PARAMETERS
|
|
|
|
typedef struct {
|
|
unsigned int ddr_mode;
|
|
unsigned int width;
|
|
unsigned int blocs;
|
|
unsigned int banks8;
|
|
unsigned int rams;
|
|
unsigned int asize;
|
|
unsigned int speed;
|
|
unsigned int cmd_mode_wr_cl_bl;
|
|
} T_DDR_CONFIG_PARAMETERS;
|
|
|
|
//cmd_mode_wr_cl_bl
|
|
//when SDR : cmd_mode_wr_cl_bl = 0x80200002 + (latency_CAS_RAM * 16) + (recovery_WR - 1) * 512; -- Sets write rec XX, CL=XX; BL=8
|
|
//else cmd_mode_wr_cl_bl = 0x80200003 + (latency_CAS_RAM * 16) + (recovery_WR - 1) * 512; -- Sets write rec XX, CL=XX; BL=8
|
|
|
|
// cmd_ bank_ dir_ lat_ rec_ width_ odt_ odt_ fix delay ratio
|
|
// A F C update offset all re re_to_we w r0 r1
|
|
// R L P R R W A A W W
|
|
//Timing Parameters A W N M R W C F R W W R W S L R
|
|
static const T_DDR_TIMING_PARAMETERS C_TP_DDR2_25E_CL5_1GB = { 4, 5, 0, 2, 4, 4,
|
|
5, 51, 23, 24, 9, 11, 18, 5, 4, 6, 3, 2, 0, 1, 2, 75, 56, 56 }; //elida device.
|
|
static const T_DDR_TIMING_PARAMETERS C_TP_DDR2_25E_CL5_2GB = { 4, 5, 0, 2, 4, 4,
|
|
5, 79, 22, 24, 9, 11, 20, 5, 4, 6, 3, 2, 0, 1, 2, 75, 56, 56 };
|
|
static const T_DDR_TIMING_PARAMETERS C_TP_DDR2_25_CL6_1GB = { 4, 5, 0, 2, 4, 4,
|
|
4, 51, 22, 26, 10, 12, 18, 6, 5, 6, 3, 2, 0, 1, 2, 75, 56, 56 }; // 400MHz, Speedgrade 25 timings (1Gb parts)
|
|
|
|
// D B B R A S
|
|
// D W L K A S P
|
|
//Config Parameters R D C 8 M Z D CMD_MODE
|
|
//static const T_DDR_CONFIG_PARAMETERS C_CP_DDR2_25E_CL5 = { 2,16, 1, 0, 1, 32,25,0x80200A53}; // 64 MByte
|
|
static const T_DDR_CONFIG_PARAMETERS C_CP_DDR2_25E_CL5 = { 2, 16, 1, 1, 1, 64,
|
|
25, 0x80200A53 }; // 128 MByte
|
|
static const T_DDR_CONFIG_PARAMETERS C_CP_DDR2_25_CL6 = { 2, 16, 1, 1, 1, 128,
|
|
25, 0x80200A63 }; // 256 MByte
|
|
|
|
static void ddr_phy_poll_until_locked(void)
|
|
{
|
|
volatile UINT reg_tmp = 0;
|
|
volatile UINT locked = 0;
|
|
|
|
//Extra read to put in delay before starting to poll...
|
|
reg_tmp = *(volatile UINT *) C_DDR_REG_PHY2; // read
|
|
|
|
//POLL C_DDR_PHY2_REG register until clock and flock
|
|
//!!! Ideally have a timeout on this.
|
|
while (locked == 0) {
|
|
reg_tmp = *(volatile UINT *) C_DDR_REG_PHY2; // read
|
|
|
|
//locked when bits 30 and 31 are set
|
|
if (reg_tmp & 0xC0000000) {
|
|
locked = 1;
|
|
}
|
|
}
|
|
}
|
|
|
|
static void ddr_poll_until_not_busy(void)
|
|
{
|
|
volatile UINT reg_tmp = 0;
|
|
volatile UINT busy = 1;
|
|
|
|
//Extra read to put in delay before starting to poll...
|
|
reg_tmp = *(volatile UINT *) C_DDR_STAT_REG; // read
|
|
|
|
//POLL DDR_STAT register until no longer busy
|
|
//!!! Ideally have a timeout on this.
|
|
while (busy == 1) {
|
|
reg_tmp = *(volatile UINT *) C_DDR_STAT_REG; // read
|
|
|
|
//when bit 31 is clear - core is no longer busy
|
|
if ((reg_tmp & 0x80000000) == 0x00000000) {
|
|
busy = 0;
|
|
}
|
|
}
|
|
}
|
|
|
|
static void ddr_issue_command(int commmand)
|
|
{
|
|
*(volatile UINT *) C_DDR_CMD_REG = commmand;
|
|
ddr_poll_until_not_busy();
|
|
}
|
|
|
|
static void ddr_timing_initialisation(
|
|
const T_DDR_TIMING_PARAMETERS *ddr_timing_parameters)
|
|
{
|
|
volatile UINT reg_tmp = 0;
|
|
/* update the DDR controller registers for timing parameters */
|
|
reg_tmp = (ddr_timing_parameters->holdoff_cmd_A << 0);
|
|
reg_tmp = reg_tmp + (ddr_timing_parameters->holdoff_cmd_ARW << 4);
|
|
reg_tmp = reg_tmp + (ddr_timing_parameters->holdoff_cmd_N << 8);
|
|
reg_tmp = reg_tmp + (ddr_timing_parameters->holdoff_cmd_LM << 12);
|
|
reg_tmp = reg_tmp + (ddr_timing_parameters->holdoff_cmd_R << 16);
|
|
reg_tmp = reg_tmp + (ddr_timing_parameters->holdoff_cmd_W << 20);
|
|
reg_tmp = reg_tmp + (ddr_timing_parameters->holdoff_cmd_PC << 24);
|
|
*(volatile UINT *) C_DDR_REG_TIMING0 = reg_tmp;
|
|
|
|
reg_tmp = (ddr_timing_parameters->holdoff_cmd_RF << 0);
|
|
reg_tmp = reg_tmp + (ddr_timing_parameters->holdoff_bank_R << 8);
|
|
reg_tmp = reg_tmp + (ddr_timing_parameters->holdoff_bank_W << 16);
|
|
reg_tmp = reg_tmp + (ddr_timing_parameters->holdoff_dir_RW << 24);
|
|
reg_tmp = reg_tmp + (ddr_timing_parameters->holdoff_dir_WR << 28);
|
|
*(volatile UINT *) C_DDR_REG_TIMING1 = reg_tmp;
|
|
|
|
reg_tmp = (ddr_timing_parameters->latency_CAS << 0);
|
|
reg_tmp = reg_tmp + (ddr_timing_parameters->latency_WL << 4);
|
|
reg_tmp = reg_tmp + (ddr_timing_parameters->holdoff_FAW << 8);
|
|
reg_tmp = reg_tmp + (ddr_timing_parameters->width_update << 16);
|
|
reg_tmp = reg_tmp + (ddr_timing_parameters->odt_offset << 21);
|
|
reg_tmp = reg_tmp + (ddr_timing_parameters->odt_drive_all << 24);
|
|
|
|
*(volatile UINT *) C_DDR_REG_TIMING2 = reg_tmp;
|
|
|
|
/* Program the timing parameters in the PHY too */
|
|
reg_tmp = (ddr_timing_parameters->use_fixed_re << 16)
|
|
| (ddr_timing_parameters->delay_wr_to_re << 8)
|
|
| (ddr_timing_parameters->latency_WL << 4)
|
|
| (ddr_timing_parameters->latency_CAS << 0);
|
|
|
|
*(volatile UINT *) C_DDR_REG_PHY_TIMING = reg_tmp;
|
|
|
|
reg_tmp = ddr_timing_parameters->wr_slave_ratio;
|
|
|
|
*(volatile UINT *) C_DDR_REG_PHY_WR_RATIO = reg_tmp;
|
|
|
|
reg_tmp = ddr_timing_parameters->rd_slave_ratio0;
|
|
reg_tmp += ddr_timing_parameters->rd_slave_ratio1 << 8;
|
|
|
|
*(volatile UINT *) C_DDR_REG_PHY_RD_RATIO = reg_tmp;
|
|
|
|
}
|
|
|
|
static void ddr_normal_initialisation(
|
|
const T_DDR_CONFIG_PARAMETERS *ddr_config_parameters, int mhz)
|
|
{
|
|
int i;
|
|
volatile UINT tmp = 0;
|
|
volatile UINT reg_tmp = 0;
|
|
volatile UINT emr_cmd = 0;
|
|
UINT refresh;
|
|
|
|
//Total size of memory in Mbits...
|
|
tmp = ddr_config_parameters->rams * ddr_config_parameters->asize
|
|
* ddr_config_parameters->width;
|
|
//Deduce value to program into DDR_CFG register...
|
|
switch (tmp) {
|
|
case 16:
|
|
reg_tmp = 0x00020000 * 1;
|
|
break;
|
|
case 32:
|
|
reg_tmp = 0x00020000 * 2;
|
|
break;
|
|
case 64:
|
|
reg_tmp = 0x00020000 * 3;
|
|
break;
|
|
case 128:
|
|
reg_tmp = 0x00020000 * 4;
|
|
break;
|
|
case 256:
|
|
reg_tmp = 0x00020000 * 5;
|
|
break;
|
|
case 512:
|
|
reg_tmp = 0x00020000 * 6;
|
|
break;
|
|
case 1024:
|
|
reg_tmp = 0x00020000 * 7;
|
|
break;
|
|
case 2048:
|
|
reg_tmp = 0x00020000 * 8;
|
|
break;
|
|
default:
|
|
reg_tmp = 0; //forces sims not to work if badly configured
|
|
}
|
|
|
|
//Memory width
|
|
tmp = ddr_config_parameters->rams * ddr_config_parameters->width;
|
|
switch (tmp) {
|
|
case 8:
|
|
reg_tmp = reg_tmp + 0x00400000;
|
|
break;
|
|
case 16:
|
|
reg_tmp = reg_tmp + 0x00200000;
|
|
break;
|
|
case 32:
|
|
reg_tmp = reg_tmp + 0x00000000;
|
|
break;
|
|
default:
|
|
reg_tmp = 0; //forces sims not to work if badly configured
|
|
}
|
|
|
|
//Setup DDR Mode
|
|
switch (ddr_config_parameters->ddr_mode) {
|
|
case 0:
|
|
reg_tmp = reg_tmp + 0x00000000;
|
|
break; //SDR
|
|
case 1:
|
|
reg_tmp = reg_tmp + 0x40000000;
|
|
break; //DDR
|
|
case 2:
|
|
reg_tmp = reg_tmp + 0x80000000;
|
|
break; //DDR2
|
|
default:
|
|
reg_tmp = 0; //forces sims not to work if badly configured
|
|
}
|
|
|
|
//Setup Banks
|
|
if (ddr_config_parameters->banks8 == 1) {
|
|
reg_tmp = reg_tmp + 0x00800000;
|
|
}
|
|
|
|
//Program DDR_CFG register...
|
|
*(volatile UINT *) C_DDR_CFG_REG = reg_tmp;
|
|
|
|
//Configure PHY0 reg - se_mode is bit 1,
|
|
//needs to be 1 for DDR (single_ended drive)
|
|
switch (ddr_config_parameters->ddr_mode) {
|
|
case 0:
|
|
reg_tmp = 2 + (0 << 4);
|
|
break; //SDR
|
|
case 1:
|
|
reg_tmp = 2 + (4 << 4);
|
|
break; //DDR
|
|
case 2:
|
|
reg_tmp = 0 + (4 << 4);
|
|
break; //DDR2
|
|
default:
|
|
reg_tmp = 0;
|
|
}
|
|
|
|
//Program DDR_PHY0 register...
|
|
*(volatile UINT *) C_DDR_REG_PHY0 = reg_tmp;
|
|
|
|
//Read DDR_PHY* registers to exercise paths for vcd
|
|
reg_tmp = *(volatile UINT *) C_DDR_REG_PHY3;
|
|
reg_tmp = *(volatile UINT *) C_DDR_REG_PHY2;
|
|
reg_tmp = *(volatile UINT *) C_DDR_REG_PHY1;
|
|
reg_tmp = *(volatile UINT *) C_DDR_REG_PHY0;
|
|
|
|
//Start up sequences - Different dependant on DDR mode
|
|
switch (ddr_config_parameters->ddr_mode) {
|
|
case 2: //DDR2
|
|
//Start-up sequence: follows procedure described in Micron datasheet.
|
|
//start up DDR PHY DLL
|
|
reg_tmp = 0x00022828; // dll on, start point and inc = h28
|
|
*(volatile UINT *) C_DDR_REG_PHY2 = reg_tmp;
|
|
|
|
reg_tmp = 0x00032828; // start on, dll on, start point and inc = h28
|
|
*(volatile UINT *) C_DDR_REG_PHY2 = reg_tmp;
|
|
|
|
ddr_phy_poll_until_locked();
|
|
|
|
udelay(200); //200us
|
|
|
|
//Startup SDRAM...
|
|
//!!! Software: CK should be running for 200us before wake-up
|
|
ddr_issue_command( C_CMD_WAKE_UP);
|
|
ddr_issue_command( C_CMD_NOP);
|
|
ddr_issue_command( C_CMD_PRECHARGE_ALL);
|
|
ddr_issue_command( C_CMD_DDR2_EMR2);
|
|
ddr_issue_command( C_CMD_DDR2_EMR3);
|
|
|
|
emr_cmd = C_CMD_DDR2_EMR1 + C_CMD_ODT_75 + C_CMD_REDUCED_DRIVE
|
|
+ C_CMD_ENABLE_DLL;
|
|
|
|
ddr_issue_command(emr_cmd);
|
|
//Sets CL=3; BL=8 but also reset DLL to trigger a DLL initialisation...
|
|
udelay(1); //1us
|
|
ddr_issue_command(
|
|
ddr_config_parameters->cmd_mode_wr_cl_bl
|
|
+ C_CMD_RESET_DLL);
|
|
udelay(1); //1us
|
|
|
|
//!!! Software: Wait 200 CK cycles before...
|
|
//for(i=1; i<=2; i++) {
|
|
ddr_issue_command(C_CMD_PRECHARGE_ALL);
|
|
// !!! Software: Wait here at least 8 CK cycles
|
|
//}
|
|
//need a wait here to ensure PHY DLL lock before the refresh is issued
|
|
udelay(1); //1us
|
|
for (i = 1; i <= 2; i++) {
|
|
ddr_issue_command( C_CMD_AUTO_REFRESH);
|
|
//!!! Software: Wait here at least 8 CK cycles to satify tRFC
|
|
udelay(1); //1us
|
|
}
|
|
//As before but without 'RESET_DLL' bit set...
|
|
ddr_issue_command(ddr_config_parameters->cmd_mode_wr_cl_bl);
|
|
udelay(1); //1us
|
|
// OCD commands
|
|
ddr_issue_command(emr_cmd + C_CMD_MODE_DDR2_OCD_DFLT);
|
|
ddr_issue_command(emr_cmd + C_CMD_MODE_DDR2_OCD_EXIT);
|
|
break;
|
|
|
|
default:
|
|
break; //Do nothing
|
|
}
|
|
|
|
//Enable auto-refresh
|
|
|
|
// 8192 Refreshes required every 64ms, so maximum refresh period is 7.8125 us
|
|
// We have a 400 MHz DDR clock (2.5ns period) so max period is 3125 cycles
|
|
// Our core now does 8 refreshes in a go, so we multiply this period by 8
|
|
|
|
refresh = (64000 * mhz) / 8192; // Refresh period in clocks
|
|
|
|
reg_tmp = *(volatile UINT *) C_DDR_CFG_REG; // read
|
|
#ifdef BURST_REFRESH_ENABLE
|
|
reg_tmp |= C_CFG_REFRESH_ENABLE | (refresh * 8);
|
|
reg_tmp |= C_CFG_BURST_REFRESH_ENABLE;
|
|
#else
|
|
reg_tmp |= C_CFG_REFRESH_ENABLE | (refresh * 1);
|
|
reg_tmp &= ~C_CFG_BURST_REFRESH_ENABLE;
|
|
#endif
|
|
*(volatile UINT *) C_DDR_CFG_REG = reg_tmp;
|
|
|
|
//Verify register contents
|
|
reg_tmp = *(volatile UINT *) C_DDR_REG_PHY2; // read
|
|
//printf("Warning XXXXXXXXXXXXXXXXXXXXXX - get bad read data from C_DDR_PHY2_REG, though it looks OK on bus XXXXXXXXXXXXXXXXXX");
|
|
//TBD Check_data (read_data, dll_reg, "Error: bad C_DDR_PHY2_REG read", tb_pass);
|
|
reg_tmp = *(volatile UINT *) C_DDR_CFG_REG; // read
|
|
//TBD Check_data (read_data, cfg_reg, "Error: bad DDR_CFG read", tb_pass);
|
|
|
|
//disable optimised wrapping
|
|
if (ddr_config_parameters->ddr_mode == 2) {
|
|
reg_tmp = 0xFFFF0000;
|
|
*(volatile UINT *) C_DDR_REG_IGNORE = reg_tmp;
|
|
}
|
|
|
|
//enable midbuffer followon
|
|
reg_tmp = *(volatile UINT *) C_DDR_ARB_REG; // read
|
|
reg_tmp = 0xFFFF0000 | reg_tmp;
|
|
*(volatile UINT *) C_DDR_ARB_REG = reg_tmp;
|
|
|
|
// Enable write behind coherency checking for all clients
|
|
|
|
reg_tmp = 0xFFFF0000;
|
|
*(volatile UINT *) C_DDR_AHB4_REG = reg_tmp;
|
|
|
|
//Wait for 200 clock cycles for SDRAM DLL to lock...
|
|
udelay(1); //1us
|
|
}
|
|
|
|
// Function used to Setup DDR core
|
|
|
|
void ddr_setup(int mhz)
|
|
{
|
|
static const T_DDR_TIMING_PARAMETERS *ddr_timing_parameters =
|
|
&C_TP_DDR2_25_CL6_1GB;
|
|
static const T_DDR_CONFIG_PARAMETERS *ddr_config_parameters =
|
|
&C_CP_DDR2_25_CL6;
|
|
|
|
//Bring core out of Reset
|
|
*(volatile UINT *) C_DDR_BLKEN_REG = C_BLKEN_DDR_ON;
|
|
|
|
//DDR TIMING INITIALISTION
|
|
ddr_timing_initialisation(ddr_timing_parameters);
|
|
|
|
//DDR NORMAL INITIALISATION
|
|
ddr_normal_initialisation(ddr_config_parameters, mhz);
|
|
|
|
// route all writes through one client
|
|
*(volatile UINT *) C_DDR_TRANSACTION_ROUTING = (0
|
|
<< DDR_ROUTE_CPU0_INSTR_SHIFT)
|
|
| (1 << DDR_ROUTE_CPU0_RDDATA_SHIFT)
|
|
| (3 << DDR_ROUTE_CPU0_WRDATA_SHIFT)
|
|
| (2 << DDR_ROUTE_CPU1_INSTR_SHIFT)
|
|
| (3 << DDR_ROUTE_CPU1_RDDATA_SHIFT)
|
|
| (3 << DDR_ROUTE_CPU1_WRDATA_SHIFT);
|
|
|
|
//Bring all clients out of reset
|
|
*(volatile UINT *) C_DDR_BLKEN_REG = C_BLKEN_DDR_ON + 0x0000FFFF;
|
|
|
|
}
|
|
|
|
void set_ddr_timing(unsigned int w, unsigned int i)
|
|
{
|
|
unsigned int reg;
|
|
unsigned int wnow = 16;
|
|
unsigned int inow = 32;
|
|
|
|
/* reset all timing controls to known value (31) */
|
|
writel(DDR_PHY_TIMING_W_RST | DDR_PHY_TIMING_I_RST, DDR_PHY_TIMING);
|
|
writel(DDR_PHY_TIMING_W_RST | DDR_PHY_TIMING_I_RST | DDR_PHY_TIMING_CK,
|
|
DDR_PHY_TIMING);
|
|
writel(DDR_PHY_TIMING_W_RST | DDR_PHY_TIMING_I_RST, DDR_PHY_TIMING);
|
|
|
|
/* step up or down read delay to the requested value */
|
|
while (wnow != w) {
|
|
if (wnow < w) {
|
|
reg = DDR_PHY_TIMING_INC;
|
|
wnow++;
|
|
} else {
|
|
reg = 0;
|
|
wnow--;
|
|
}
|
|
writel(DDR_PHY_TIMING_W_CE | reg, DDR_PHY_TIMING);
|
|
writel(DDR_PHY_TIMING_CK | DDR_PHY_TIMING_W_CE | reg,
|
|
DDR_PHY_TIMING);
|
|
writel(DDR_PHY_TIMING_W_CE | reg, DDR_PHY_TIMING);
|
|
}
|
|
|
|
/* now write delay */
|
|
while (inow != i) {
|
|
if (inow < i) {
|
|
reg = DDR_PHY_TIMING_INC;
|
|
inow++;
|
|
} else {
|
|
reg = 0;
|
|
inow--;
|
|
}
|
|
writel(DDR_PHY_TIMING_I_CE | reg, DDR_PHY_TIMING);
|
|
writel(DDR_PHY_TIMING_CK | DDR_PHY_TIMING_I_CE | reg,
|
|
DDR_PHY_TIMING);
|
|
writel(DDR_PHY_TIMING_I_CE | reg, DDR_PHY_TIMING);
|
|
}
|
|
}
|
|
|
|
//Function used to Setup SDRAM in DDR/SDR mode
|
|
void init_ddr(int mhz)
|
|
{
|
|
/* start clocks */
|
|
enable_clock(SYS_CTRL_CLK_DDRPHY);
|
|
enable_clock(SYS_CTRL_CLK_DDR);
|
|
enable_clock(SYS_CTRL_CLK_DDRCK);
|
|
|
|
/* bring phy and core out of reset */
|
|
reset_block(SYS_CTRL_RST_DDR_PHY, 0);
|
|
reset_block(SYS_CTRL_RST_DDR, 0);
|
|
|
|
/* DDR runs at half the speed of the CPU */
|
|
ddr_setup(mhz >> 1);
|
|
return;
|
|
}
|