6b813e36f8
The bootloader was updated and now uses 115200 instead of 57600 baud for the serial console. Change this also in OpenWrt's DTS, so the rate is consistent for bootloader and linux kernel output. Signed-off-by: Daniel Golle <daniel@makrotopia.org> SVN-Revision: 48359
128 lines
2.0 KiB
Plaintext
128 lines
2.0 KiB
Plaintext
/dts-v1/;
|
|
|
|
#include "mt7621.dtsi"
|
|
|
|
/ {
|
|
compatible = "mediatek,mt7621-eval-board", "mediatek,mt7621-soc";
|
|
model = "ZBT-WG2626";
|
|
|
|
memory@0 {
|
|
device_type = "memory";
|
|
reg = <0x0 0x1c000000>, <0x20000000 0x4000000>;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200";
|
|
};
|
|
|
|
sdhci@10130000 {
|
|
status = "okay";
|
|
};
|
|
|
|
palmbus@1E000000 {
|
|
spi@b00 {
|
|
status = "okay";
|
|
|
|
m25p80@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0 0>;
|
|
linux,modalias = "m25p80";
|
|
spi-max-frequency = <10000000>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x30000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@30000 {
|
|
label = "u-boot-env";
|
|
reg = <0x30000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
factory: partition@40000 {
|
|
label = "factory";
|
|
reg = <0x40000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@50000 {
|
|
label = "firmware";
|
|
reg = <0x50000 0xfb0000>;
|
|
};
|
|
|
|
};
|
|
};
|
|
|
|
i2c@900 {
|
|
compatible = "ralink,i2c-mt7621";
|
|
reg = <0x900 0x100>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&i2c_pins>;
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
pcie@1e140000 {
|
|
status = "okay";
|
|
|
|
pcie0 {
|
|
mt76@0,0 {
|
|
reg = <0x0000 0 0 0 0>;
|
|
device_type = "pci";
|
|
mediatek,mtd-eeprom = <&factory 0x8000>;
|
|
mediatek,2ghz = <0>;
|
|
};
|
|
};
|
|
|
|
pcie1 {
|
|
mt76@1,0 {
|
|
reg = <0x0000 0 0 0 0>;
|
|
device_type = "pci";
|
|
mediatek,mtd-eeprom = <&factory 0x0000>;
|
|
mediatek,5ghz = <0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
ethernet@1e100000 {
|
|
mtd-mac-address = <&factory 0xe000>;
|
|
};
|
|
|
|
gpio-keys-polled {
|
|
compatible = "gpio-keys-polled";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
poll-interval = <20>;
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio0 18 1>;
|
|
linux,code = <0x198>;
|
|
};
|
|
};
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
|
|
status {
|
|
label = "zbt-wg2626:green:status";
|
|
gpios = <&gpio0 24 1>;
|
|
};
|
|
};
|
|
|
|
pinctrl {
|
|
state_default: pinctrl0 {
|
|
gpio {
|
|
ralink,group = "wdt", "rgmii2", "wdt rst", "jtag", "mdio";
|
|
ralink,function = "gpio";
|
|
};
|
|
};
|
|
};
|
|
};
|