c3693e53f4
Compared to the "old" driver: - Each device must assign a pinctrl setting to the SPI node to allow the new SPI driver to configure the SPI pins. While here we are also using separate input and output settings so we are independent of whether the bootloader configures the pins correctly. - We use the new "compatible" strings to make the driver choose the correct number of chip-selects for each SoC. - The new driver starts counting the chip-selects at 1 (instead of 0, like the old one did). Thus we have to adjust the devices accordingly. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> SVN-Revision: 48293
75 lines
1.9 KiB
Plaintext
75 lines
1.9 KiB
Plaintext
CONFIG_ADM6996_PHY=y
|
|
CONFIG_AR8216_PHY=y
|
|
# CONFIG_ARCH_HAS_SG_CHAIN is not set
|
|
CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
|
|
CONFIG_ARCH_MIGHT_HAVE_PC_SERIO=y
|
|
CONFIG_CLONE_BACKWARDS=y
|
|
CONFIG_CPU_NEEDS_NO_SMARTMIPS_OR_MICROMIPS=y
|
|
CONFIG_CPU_SUPPORTS_MSA=y
|
|
CONFIG_CRC16=y
|
|
CONFIG_CRYPTO_DEFLATE=y
|
|
CONFIG_CRYPTO_LZO=y
|
|
CONFIG_FIRMWARE_IN_KERNEL=y
|
|
CONFIG_GPIO_DEVRES=y
|
|
CONFIG_HAS_IOPORT_MAP=y
|
|
# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
|
|
CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
|
|
CONFIG_HAVE_ARCH_TRACEHOOK=y
|
|
# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
|
|
CONFIG_HAVE_BPF_JIT=y
|
|
CONFIG_HAVE_CC_STACKPROTECTOR=y
|
|
CONFIG_HAVE_CONTEXT_TRACKING=y
|
|
CONFIG_HAVE_DEBUG_STACKOVERFLOW=y
|
|
CONFIG_HAVE_DMA_CONTIGUOUS=y
|
|
CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
|
|
CONFIG_HZ_PERIODIC=y
|
|
CONFIG_INPUT=y
|
|
CONFIG_INPUT_EVDEV=y
|
|
CONFIG_INPUT_POLLDEV=y
|
|
CONFIG_IRQCHIP=y
|
|
CONFIG_IRQ_WORK=y
|
|
# CONFIG_ISDN is not set
|
|
CONFIG_LANTIQ_PHY=y
|
|
CONFIG_LANTIQ_XRX200=y
|
|
CONFIG_LEDS_TRIGGER_HEARTBEAT=y
|
|
CONFIG_LIBFDT=y
|
|
CONFIG_LZO_COMPRESS=y
|
|
CONFIG_LZO_DECOMPRESS=y
|
|
CONFIG_MTD_NAND=y
|
|
CONFIG_MTD_NAND_ECC=y
|
|
CONFIG_MTD_NAND_PLATFORM=y
|
|
CONFIG_MTD_NAND_XWAY=y
|
|
# CONFIG_MTD_PHYSMAP_OF is not set
|
|
CONFIG_MTD_UBI=y
|
|
CONFIG_MTD_UBI_BEB_LIMIT=20
|
|
CONFIG_MTD_UBI_BLOCK=y
|
|
# CONFIG_MTD_UBI_FASTMAP is not set
|
|
# CONFIG_MTD_UBI_GLUEBI is not set
|
|
CONFIG_MTD_UBI_WL_THRESHOLD=4096
|
|
CONFIG_NLS=y
|
|
# CONFIG_NO_IOPORT_MAP is not set
|
|
CONFIG_OF_ADDRESS_PCI=y
|
|
CONFIG_PCIE_LANTIQ=y
|
|
# CONFIG_RCU_STALL_COMMON is not set
|
|
CONFIG_RTL8306_PHY=y
|
|
CONFIG_RTL8366S_PHY=y
|
|
CONFIG_RTL8367B_PHY=y
|
|
CONFIG_RTL8367_PHY=y
|
|
CONFIG_SPI=y
|
|
CONFIG_SPI_LANTIQ=y
|
|
CONFIG_SPI_MASTER=y
|
|
CONFIG_SYS_SUPPORTS_MIPS16=y
|
|
CONFIG_UBIFS_FS=y
|
|
CONFIG_UBIFS_FS_ADVANCED_COMPR=y
|
|
CONFIG_UBIFS_FS_LZO=y
|
|
# CONFIG_UBIFS_FS_XZ is not set
|
|
CONFIG_UBIFS_FS_ZLIB=y
|
|
CONFIG_USB=y
|
|
CONFIG_USB_COMMON=y
|
|
# CONFIG_USB_EHCI_HCD is not set
|
|
CONFIG_USB_SUPPORT=y
|
|
# CONFIG_USB_UHCI_HCD is not set
|
|
CONFIG_XRX200_PHY_FW=y
|
|
CONFIG_ZLIB_DEFLATE=y
|
|
CONFIG_ZLIB_INFLATE=y
|