openwrt_archive/target/linux/lantiq/dts/VGV7510KW22.dtsi
John Crispin d5b866bd33 lantiq: move partitions into partion table node
Starting with kernel 4.4, the use of partitions as direct subnodes of the
mtd device is discouraged and only supported for backward compatiblity
reasons.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 49280
2016-05-02 18:50:18 +00:00

263 lines
4.9 KiB
Plaintext

/include/ "vr9.dtsi"
/ {
model = "VGV7510KW22 - o2 Box 6431";
chosen {
bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
leds {
boot = &power_green;
failsafe = &power_red;
running = &power_green;
dsl = &dsl;
internet = &internet_green;
wifi = &wifi;
};
};
memory@0 {
reg = <0x0 0x4000000>;
};
fpi@10000000 {
localbus@0 {
nor-boot@0 {
compatible = "lantiq,nor";
bank-width = <2>;
reg = <0 0x0 0x1000000>;
#address-cells = <1>;
#size-cells = <1>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
boardconfig: partition@fe0000 {
label = "board_config";
reg = <0xfe0000 0x20000>;
read-only;
};
};
};
};
gpio: pinmux@E100B10 {
pinctrl-names = "default";
pinctrl-0 = <&state_default>;
state_default: pinmux {
ip101a-rst {
lantiq,pins = "io46";
lantiq,output = <0>;
lantiq,pull = <1>;
};
gphy-leds {
lantiq,groups = "gphy0 led1",
"gphy1 led0", "gphy1 led1";
lantiq,function = "gphy";
lantiq,open-drain = <0>;
lantiq,pull = <0>;
lantiq,output = <1>;
};
stp {
lantiq,groups = "stp";
lantiq,function = "stp";
lantiq,pull = <2>;
lantiq,open-drain = <0>;
lantiq,output = <1>;
};
mdio {
lantiq,groups = "mdio";
lantiq,function = "mdio";
};
pci-rst {
lantiq,pins = "io21";
lantiq,open-drain = <0>;
lantiq,pull = <0>;
lantiq,output = <1>;
};
spi {
lantiq,groups = "spi_di", "spi_do", "spi_clk";
lantiq,function = "spi";
};
};
};
stp: stp@E100BB0 {
compatible = "lantiq,gpio-stp-xway";
reg = <0xE100BB0 0x40>;
#gpio-cells = <2>;
gpio-controller;
lantiq,shadow = <0xff>;
lantiq,groups = <0x1>;
lantiq,dsl = <0x0>;
lantiq,phy1 = <0x7>;
lantiq,phy2 = <0x7>; /* enable gphy0 led2 = LAN2 LED */
};
ifxhcd@E101000 {
status = "okay";
gpios = <&gpio 47 0>;
};
pci@E105400 {
status = "okay";
lantiq,bus-clock = <33333333>;
interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
0x7000 0 0 1 &icu0 30 1 // slot 14, irq 30
>;
gpio-reset = <&gpio 21 0>;
req-mask = <0x1>; /* GNT1 */
};
pcie@d900000 {
status = "disabled";
};
};
gphy-xrx200 {
compatible = "lantiq,phy-xrx200";
firmware1 = "lantiq/vr9_phy22f_a1x.bin"; /*VR9 1.1*/
firmware2 = "lantiq/vr9_phy22f_a2x.bin"; /*VR9 1.2*/
phys = [ 00 01 ];
};
ralink_eep {
compatible = "ralink,eeprom";
ralink,eeprom = "RT3062.eeprom";
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <100>;
reset {
label = "reset";
gpios = <&gpio 6 1>;
linux,code = <0x198>;
};
wps {
label = "wps";
gpios = <&gpio 9 1>;
linux,code = <0x211>;
};
};
gpio-leds {
compatible = "gpio-leds";
dsl: dsl {
label = "vgv7510kw22:green:dsl";
gpios = <&gpio 2 1>;
};
internet_red {
label = "vgv7510kw22:red:internet";
gpios = <&gpio 10 1>;
};
info_red {
label = "vgv7510kw22:red:info";
gpios = <&gpio 12 1>;
};
power_green: power {
label = "vgv7510kw22:green:power";
gpios = <&gpio 14 1>;
default-state = "keep";
};
info_green {
label = "vgv7510kw22:green:info";
gpios = <&gpio 15 1>;
};
internet_green: internet_green {
label = "vgv7510kw22:green:internet";
gpios = <&gpio 19 1>;
};
wifi: wifi {
label = "vgv7510kw22:green:wlan";
gpios = <&gpio 20 1>;
};
power_red: power2 {
label = "vgv7510kw22:red:power";
gpios = <&gpio 28 1>;
};
phone {
label = "vgv7510kw22:green:telefon";
gpios = <&gpio 29 1>;
};
};
};
&eth0 {
lan: interface@0 {
compatible = "lantiq,xrx200-pdi";
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
mtd-mac-address = <&boardconfig 0x16>;
lantiq,switch;
ethernet@2 {
compatible = "lantiq,xrx200-pdi-port";
reg = <2>;
phy-mode = "mii";
phy-handle = <&phy11>;
};
ethernet@3 {
compatible = "lantiq,xrx200-pdi-port";
reg = <3>;
phy-mode = "mii";
phy-handle = <&phy12>;
};
ethernet@4 {
compatible = "lantiq,xrx200-pdi-port";
reg = <4>;
phy-mode = "mii";
phy-handle = <&phy13>;
};
ethernet@5 {
compatible = "lantiq,xrx200-pdi-port";
reg = <5>;
phy-mode = "mii";
phy-handle = <&phy14>;
};
};
mdio@0 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "lantiq,xrx200-mdio";
phy11: ethernet-phy@11 {
reg = <0x11>;
compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22";
};
phy12: ethernet-phy@12 {
reg = <0x12>;
compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22";
};
phy13: ethernet-phy@13 {
reg = <0x13>;
compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22";
};
phy14: ethernet-phy@14 {
reg = <0x14>;
compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22";
};
};
};