Openwrt/openwrt_archive
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
attitude_adjustment
openwrt_archive/target/linux/brcm47xx/patches-3.3/700-ssb-gigabit-ethernet-driver.patch
Hauke Mehrtens aa39a43602 kernel: update bcma and ssb to wireless-testing/master master-2013-07-03 
This updates 025-bcma_backport.patch and 020-ssb_update.patch to a 
version of ssb and bcma used in recent wireless-testing. I removed all 
patches adding serial and nand flash support before doing so to not 
conflict with the existing flash support in the brcm47xx target. This 
update was done to easily update the wireless drivers afterwards.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>


SVN-Revision: 37261
2013-07-11 22:20:26 +00:00

403 lines
12 KiB
Diff
Raw Permalink Blame History

--- a/drivers/net/ethernet/broadcom/tg3.c
+++ b/drivers/net/ethernet/broadcom/tg3.c
@@ -44,6 +44,7 @@
#include <linux/prefetch.h>
#include <linux/dma-mapping.h>
#include <linux/firmware.h>
+#include <linux/ssb/ssb_driver_gige.h>
#include <net/checksum.h>
#include <net/ip.h>
@@ -249,6 +250,7 @@ static DEFINE_PCI_DEVICE_TABLE(tg3_pci_t
{PCI_DEVICE(PCI_VENDOR_ID_BROADCOM, PCI_DEVICE_ID_TIGON3_5705F)},
{PCI_DEVICE(PCI_VENDOR_ID_BROADCOM, PCI_DEVICE_ID_TIGON3_5721)},
{PCI_DEVICE(PCI_VENDOR_ID_BROADCOM, PCI_DEVICE_ID_TIGON3_5722)},
+ {PCI_DEVICE(PCI_VENDOR_ID_BROADCOM, PCI_DEVICE_ID_TIGON3_5750)},
{PCI_DEVICE(PCI_VENDOR_ID_BROADCOM, PCI_DEVICE_ID_TIGON3_5751)},
{PCI_DEVICE(PCI_VENDOR_ID_BROADCOM, PCI_DEVICE_ID_TIGON3_5751M)},
{PCI_DEVICE(PCI_VENDOR_ID_BROADCOM, PCI_DEVICE_ID_TIGON3_5751F)},
@@ -530,7 +532,9 @@ static void _tw32_flush(struct tg3 *tp,
static inline void tw32_mailbox_flush(struct tg3 *tp, u32 off, u32 val)
{
tp->write32_mbox(tp, off, val);
- if (!tg3_flag(tp, MBOX_WRITE_REORDER) && !tg3_flag(tp, ICH_WORKAROUND))
+ if (tg3_flag(tp, FLUSH_POSTED_WRITES) ||
+ (!tg3_flag(tp, MBOX_WRITE_REORDER) &&
+ !tg3_flag(tp, ICH_WORKAROUND)))
tp->read32_mbox(tp, off);
}
@@ -540,7 +544,8 @@ static void tg3_write32_tx_mbox(struct t
writel(val, mbox);
if (tg3_flag(tp, TXD_MBOX_HWBUG))
writel(val, mbox);
- if (tg3_flag(tp, MBOX_WRITE_REORDER))
+ if (tg3_flag(tp, MBOX_WRITE_REORDER) ||
+ tg3_flag(tp, FLUSH_POSTED_WRITES))
readl(mbox);
}
@@ -948,7 +953,8 @@ static void tg3_switch_clocks(struct tg3
#define PHY_BUSY_LOOPS 5000
-static int tg3_readphy(struct tg3 *tp, int reg, u32 *val)
+static int __tg3_readphy(struct tg3 *tp, unsigned int phy_addr, int reg,
+ u32 *val)
{
u32 frame_val;
unsigned int loops;
@@ -962,7 +968,7 @@ static int tg3_readphy(struct tg3 *tp, i
*val = 0x0;
- frame_val = ((tp->phy_addr << MI_COM_PHY_ADDR_SHIFT) &
+ frame_val = ((phy_addr << MI_COM_PHY_ADDR_SHIFT) &
MI_COM_PHY_ADDR_MASK);
frame_val |= ((reg << MI_COM_REG_ADDR_SHIFT) &
MI_COM_REG_ADDR_MASK);
@@ -997,7 +1003,13 @@ static int tg3_readphy(struct tg3 *tp, i
return ret;
}
-static int tg3_writephy(struct tg3 *tp, int reg, u32 val)
+static int tg3_readphy(struct tg3 *tp, int reg, u32 *val)
+{
+ return __tg3_readphy(tp, tp->phy_addr, reg, val);
+}
+
+static int __tg3_writephy(struct tg3 *tp, unsigned int phy_addr, int reg,
+ u32 val)
{
u32 frame_val;
unsigned int loops;
@@ -1013,7 +1025,7 @@ static int tg3_writephy(struct tg3 *tp,
udelay(80);
}
- frame_val = ((tp->phy_addr << MI_COM_PHY_ADDR_SHIFT) &
+ frame_val = ((phy_addr << MI_COM_PHY_ADDR_SHIFT) &
MI_COM_PHY_ADDR_MASK);
frame_val |= ((reg << MI_COM_REG_ADDR_SHIFT) &
MI_COM_REG_ADDR_MASK);
@@ -1046,6 +1058,11 @@ static int tg3_writephy(struct tg3 *tp,
return ret;
}
+static int tg3_writephy(struct tg3 *tp, int reg, u32 val)
+{
+ return __tg3_writephy(tp, tp->phy_addr, reg, val);
+}
+
static int tg3_phy_cl45_write(struct tg3 *tp, u32 devad, u32 addr, u32 val)
{
int err;
@@ -1608,6 +1625,11 @@ static int tg3_poll_fw(struct tg3 *tp)
int i;
u32 val;
+ if (tg3_flag(tp, IS_SSB_CORE)) {
+ /* We don't use firmware. */
+ return 0;
+ }
+
if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5906) {
/* Wait up to 20ms for init done. */
for (i = 0; i < 200; i++) {
@@ -3015,6 +3037,11 @@ static int tg3_halt_cpu(struct tg3 *tp,
tw32_f(offset + CPU_MODE, CPU_MODE_HALT);
udelay(10);
} else {
+ /* There is only an Rx CPU for the 5750 derivative in the
+ * BCM4785. */
+ if (tg3_flag(tp, IS_SSB_CORE))
+ return 0;
+
for (i = 0; i < 10000; i++) {
tw32(offset + CPU_STATE, 0xffffffff);
tw32(offset + CPU_MODE, CPU_MODE_HALT);
@@ -3029,9 +3056,12 @@ static int tg3_halt_cpu(struct tg3 *tp,
return -ENODEV;
}
- /* Clear firmware's nvram arbitration. */
- if (tg3_flag(tp, NVRAM))
- tw32(NVRAM_SWARB, SWARB_REQ_CLR0);
+ if (!tg3_flag(tp, IS_SSB_CORE)) {
+ /* Clear firmware's nvram arbitration. */
+ if (tg3_flag(tp, NVRAM))
+ tw32(NVRAM_SWARB, SWARB_REQ_CLR0);
+ }
+
return 0;
}
@@ -3094,6 +3124,11 @@ static int tg3_load_5701_a0_firmware_fix
const __be32 *fw_data;
int err, i;
+ if (tg3_flag(tp, IS_SSB_CORE)) {
+ /* We don't use firmware. */
+ return 0;
+ }
+
fw_data = (void *)tp->fw->data;
/* Firmware blob starts with version numbers, followed by
@@ -3150,6 +3185,11 @@ static int tg3_load_tso_firmware(struct
unsigned long cpu_base, cpu_scratch_base, cpu_scratch_size;
int err, i;
+ if (tg3_flag(tp, IS_SSB_CORE)) {
+ /* We don't use firmware. */
+ return 0;
+ }
+
if (tg3_flag(tp, HW_TSO_1) ||
tg3_flag(tp, HW_TSO_2) ||
tg3_flag(tp, HW_TSO_3))
@@ -3496,8 +3536,9 @@ static int tg3_power_down_prepare(struct
tg3_frob_aux_power(tp, true);
/* Workaround for unstable PLL clock */
- if ((GET_CHIP_REV(tp->pci_chip_rev_id) == CHIPREV_5750_AX) ||
- (GET_CHIP_REV(tp->pci_chip_rev_id) == CHIPREV_5750_BX)) {
+ if ((!tg3_flag(tp, IS_SSB_CORE)) &&
+ ((GET_CHIP_REV(tp->pci_chip_rev_id) == CHIPREV_5750_AX) ||
+ (GET_CHIP_REV(tp->pci_chip_rev_id) == CHIPREV_5750_BX))) {
u32 val = tr32(0x7d00);
val &= ~((1 << 16) | (1 << 4) | (1 << 2) | (1 << 1) | 1);
@@ -4011,6 +4052,14 @@ relink:
if (current_link_up == 0 || (tp->phy_flags & TG3_PHYFLG_IS_LOW_POWER)) {
tg3_phy_copper_begin(tp);
+ if (tg3_flag(tp, ROBOSWITCH)) {
+ current_link_up = 1;
+ current_speed = SPEED_1000; /* FIXME */
+ current_duplex = DUPLEX_FULL;
+ tp->link_config.active_speed = current_speed;
+ tp->link_config.active_duplex = current_duplex;
+ }
+
tg3_readphy(tp, MII_BMSR, &bmsr);
if ((!tg3_readphy(tp, MII_BMSR, &bmsr) && (bmsr & BMSR_LSTATUS)) ||
(tp->mac_mode & MAC_MODE_PORT_INT_LPBACK))
@@ -4029,6 +4078,26 @@ relink:
else
tp->mac_mode |= MAC_MODE_PORT_MODE_GMII;
+ /* In order for the 5750 core in BCM4785 chip to work properly
+ * in RGMII mode, the Led Control Register must be set up.
+ */
+ if (tg3_flag(tp, RGMII_MODE)) {
+ u32 led_ctrl = tr32(MAC_LED_CTRL);
+ led_ctrl &= ~(LED_CTRL_1000MBPS_ON | LED_CTRL_100MBPS_ON);
+
+ if (tp->link_config.active_speed == SPEED_10)
+ led_ctrl |= LED_CTRL_LNKLED_OVERRIDE;
+ else if (tp->link_config.active_speed == SPEED_100)
+ led_ctrl |= (LED_CTRL_LNKLED_OVERRIDE |
+ LED_CTRL_100MBPS_ON);
+ else if (tp->link_config.active_speed == SPEED_1000)
+ led_ctrl |= (LED_CTRL_LNKLED_OVERRIDE |
+ LED_CTRL_1000MBPS_ON);
+
+ tw32(MAC_LED_CTRL, led_ctrl);
+ udelay(40);
+ }
+
tp->mac_mode &= ~MAC_MODE_HALF_DUPLEX;
if (tp->link_config.active_duplex == DUPLEX_HALF)
tp->mac_mode |= MAC_MODE_HALF_DUPLEX;
@@ -7833,6 +7902,14 @@ static int tg3_chip_reset(struct tg3 *tp
tw32(0x5000, 0x400);
}
+ if (tg3_flag(tp, IS_SSB_CORE)) {
+ /* BCM4785: In order to avoid repercussions from using
+ * potentially defective internal ROM, stop the Rx RISC CPU,
+ * which is not required. */
+ tg3_stop_fw(tp);
+ tg3_halt_cpu(tp, RX_CPU_BASE);
+ }
+
tw32(GRC_MODE, tp->grc_mode);
if (tp->pci_chip_rev_id == CHIPREV_ID_5705_A0) {
@@ -9247,6 +9324,11 @@ static void tg3_timer(unsigned long __op
tg3_flag(tp, 57765_CLASS))
tg3_chk_missed_msi(tp);
+ if (tg3_flag(tp, FLUSH_POSTED_WRITES)) {
+ /* BCM4785: Flush posted writes from GbE to host memory. */
+ tr32(HOSTCC_MODE);
+ }
+
if (!tg3_flag(tp, TAGGED_STATUS)) {
/* All of this garbage is because when using non-tagged
* IRQ status the mailbox/status_block protocol the chip
@@ -10959,6 +11041,11 @@ static int tg3_test_nvram(struct tg3 *tp
if (tg3_flag(tp, NO_NVRAM))
return 0;
+ if (tg3_flag(tp, IS_SSB_CORE)) {
+ /* We don't have NVRAM. */
+ return 0;
+ }
+
if (tg3_nvram_read(tp, 0, &magic) != 0)
return -EIO;
@@ -11916,11 +12003,12 @@ static int tg3_ioctl(struct net_device *
if (tp->phy_flags & TG3_PHYFLG_PHY_SERDES)
break; /* We have no PHY */
- if (!netif_running(dev))
+ if (tp->phy_flags & TG3_PHYFLG_IS_LOW_POWER)
return -EAGAIN;
spin_lock_bh(&tp->lock);
- err = tg3_readphy(tp, data->reg_num & 0x1f, &mii_regval);
+ err = __tg3_readphy(tp, data->phy_id & 0x1f,
+ data->reg_num & 0x1f, &mii_regval);
spin_unlock_bh(&tp->lock);
data->val_out = mii_regval;
@@ -11932,11 +12020,12 @@ static int tg3_ioctl(struct net_device *
if (tp->phy_flags & TG3_PHYFLG_PHY_SERDES)
break; /* We have no PHY */
- if (!netif_running(dev))
+ if (tp->phy_flags & TG3_PHYFLG_IS_LOW_POWER)
return -EAGAIN;
spin_lock_bh(&tp->lock);
- err = tg3_writephy(tp, data->reg_num & 0x1f, data->val_in);
+ err = __tg3_writephy(tp, data->phy_id & 0x1f,
+ data->reg_num & 0x1f, data->val_in);
spin_unlock_bh(&tp->lock);
return err;
@@ -12670,6 +12759,13 @@ static void __devinit tg3_get_5720_nvram
/* Chips other than 5700/5701 use the NVRAM for fetching info. */
static void __devinit tg3_nvram_init(struct tg3 *tp)
{
+ if (tg3_flag(tp, IS_SSB_CORE)) {
+ /* No NVRAM and EEPROM on the SSB Broadcom GigE core. */
+ tg3_flag_clear(tp, NVRAM);
+ tg3_flag_clear(tp, NVRAM_BUFFERED);
+ return;
+ }
+
tw32_f(GRC_EEPROM_ADDR,
(EEPROM_ADDR_FSM_RESET |
(EEPROM_DEFAULT_CLOCK_PERIOD <<
@@ -12936,6 +13032,9 @@ static int tg3_nvram_write_block(struct
{
int ret;
+ if (tg3_flag(tp, IS_SSB_CORE))
+ return -ENODEV;
+
if (tg3_flag(tp, EEPROM_WRITE_PROT)) {
tw32_f(GRC_LOCAL_CTRL, tp->grc_local_ctrl &
~GRC_LCLCTRL_GPIO_OUTPUT1);
@@ -13394,10 +13493,19 @@ static int __devinit tg3_phy_probe(struc
* subsys device table.
*/
p = tg3_lookup_by_subsys(tp);
- if (!p)
+ if (p) {
+ tp->phy_id = p->phy_id;
+ } else if (!tg3_flag(tp, IS_SSB_CORE)) {
+ /* For now we saw the IDs 0xbc050cd0,
+ * 0xbc050f80 and 0xbc050c30 on devices
+ * connected to an BCM4785 and there are
+ * probably more. Just assume that the phy is
+ * supported when it is connected to a SSB core
+ * for now.
+ */
return -ENODEV;
+ }
- tp->phy_id = p->phy_id;
if (!tp->phy_id ||
tp->phy_id == TG3_PHY_ID_BCM8002)
tp->phy_flags |= TG3_PHYFLG_PHY_SERDES;
@@ -14382,6 +14490,11 @@ static int __devinit tg3_get_invariants(
}
}
+ if (tg3_flag(tp, FLUSH_POSTED_WRITES)) {
+ tp->write32_tx_mbox = tg3_write_flush_reg32;
+ tp->write32_rx_mbox = tg3_write_flush_reg32;
+ }
+
/* Get eeprom hw config before calling tg3_set_power_state().
* In particular, the TG3_FLAG_IS_NIC flag must be
* determined before calling tg3_set_power_state() so that
@@ -14798,6 +14911,10 @@ static int __devinit tg3_get_device_addr
}
if (!is_valid_ether_addr(&dev->dev_addr[0])) {
+ if (tg3_flag(tp, IS_SSB_CORE))
+ ssb_gige_get_macaddr(tp->pdev, &dev->dev_addr[0]);
+ }
+ if (!is_valid_ether_addr(&dev->dev_addr[0])) {
#ifdef CONFIG_SPARC
if (!tg3_get_default_macaddr_sparc(tp))
return 0;
@@ -15082,7 +15199,8 @@ static int __devinit tg3_test_dma(struct
if (tg3_flag(tp, 40BIT_DMA_BUG) &&
GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5704)
tp->dma_rwctrl |= 0x8000;
- else if (ccval == 0x6 || ccval == 0x7)
+ else if ((ccval == 0x6 || ccval == 0x7) ||
+ tg3_flag(tp, ONE_DMA_AT_ONCE))
tp->dma_rwctrl |= DMA_RWCTRL_ONE_DMA;
if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5703)
@@ -15506,6 +15624,17 @@ static int __devinit tg3_init_one(struct
tp->msg_enable = tg3_debug;
else
tp->msg_enable = TG3_DEF_MSG_ENABLE;
+ if (pdev_is_ssb_gige_core(pdev)) {
+ tg3_flag_set(tp, IS_SSB_CORE);
+ if (ssb_gige_must_flush_posted_writes(pdev))
+ tg3_flag_set(tp, FLUSH_POSTED_WRITES);
+ if (ssb_gige_one_dma_at_once(pdev))
+ tg3_flag_set(tp, ONE_DMA_AT_ONCE);
+ if (ssb_gige_have_roboswitch(pdev))
+ tg3_flag_set(tp, ROBOSWITCH);
+ if (ssb_gige_is_rgmii(pdev))
+ tg3_flag_set(tp, RGMII_MODE);
+ }
/* The word/byte swap controls here control register access byte
* swapping. DMA data byte swapping is controlled in the GRC_MODE
--- a/drivers/net/ethernet/broadcom/tg3.h
+++ b/drivers/net/ethernet/broadcom/tg3.h
@@ -2940,6 +2940,11 @@ enum TG3_FLAGS {
TG3_FLAG_57765_PLUS,
TG3_FLAG_57765_CLASS,
TG3_FLAG_5717_PLUS,
+ TG3_FLAG_IS_SSB_CORE,
+ TG3_FLAG_FLUSH_POSTED_WRITES,
+ TG3_FLAG_ROBOSWITCH,
+ TG3_FLAG_ONE_DMA_AT_ONCE,
+ TG3_FLAG_RGMII_MODE,
/* Add new flags before this comment and TG3_FLAG_NUMBER_OF_FLAGS */
TG3_FLAG_NUMBER_OF_FLAGS, /* Last entry in enum TG3_FLAGS */
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -2120,6 +2120,7 @@
#define PCI_DEVICE_ID_TIGON3_5754M 0x1672
#define PCI_DEVICE_ID_TIGON3_5755M 0x1673
#define PCI_DEVICE_ID_TIGON3_5756 0x1674
+#define PCI_DEVICE_ID_TIGON3_5750 0x1676
#define PCI_DEVICE_ID_TIGON3_5751 0x1677
#define PCI_DEVICE_ID_TIGON3_5715 0x1678
#define PCI_DEVICE_ID_TIGON3_5715S 0x1679
Reference in New Issue View Git Blame Copy Permalink