mirror of
https://git.openwrt.org/openwrt/openwrt.git
synced 2025-02-24 16:28:46 +00:00
4642d8abdc
Iomega Storcenter ix4-200d is a four-bay SATA NAS powered by a Marvell Kirkwood SoC clocked at 1.2GHz. It has 512MB of RAM and 32MB of flash memory, 3x USB 2.0 and 2x 1Gbit/s NIC Specification: - SoC: Marvell Kirkwood 88F6281 - CPU/Speed: 1200Mhz - Flash size: 32 MiB - RAM: 512MB - LAN: 2x 1Gbit/s - 3x USB 2.0 Notes: - The blue drive LED is triggered by HDD activity, it can not be controlled via GPIO. - The LCD screen requires proprietary code and does not function at this time. - Due to a kernel-related issue with the Marvell 88SE6121 SATA controller, currently only trays numbered #3 and #4 work, #1 and #2 do not. [1] Serial pinout: CN4 -------------- | 10 8 6 4 2 | | 9 7 5 3 1 | -------------- PIN 1 Mark (fat line) 1 = RXD 4 = TXD 6 = GND 9 = 3.3V (not necessary to connect) Installation instructions: 1. download initramfs-uImage and copy into tftp server 2. connect the tftp server to network port #1 3. access uboot environment with serial cable and run setenv mainlineLinux yes setenv arcNumber 1682 setenv console 'console=ttyS0,115200n8' setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)' setenv bootargs_root 'root=' setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000' saveenv setenv serverip 192.168.1.1 setenv ipaddr 192.168.1.2 tftpboot 0x00800000 [initramfs-uImage filename] bootm 0x00800000 4. connect to LAN on network port #2, log into openwrt and sysupgrade to install into flash [1] https://bugzilla.kernel.org/show_bug.cgi?id=216094 Signed-off-by: Sander van Deijck <sander@vandeijck.com> (aligned FROM from signed-off. LED+key rename, whitespace removal) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
89 lines
1.7 KiB
Plaintext
89 lines
1.7 KiB
Plaintext
#
|
|
# Copyright (C) 2012-2015 OpenWrt.org
|
|
#
|
|
|
|
. /lib/functions/uci-defaults.sh
|
|
. /lib/functions/system.sh
|
|
|
|
kirkwood_setup_interfaces()
|
|
{
|
|
local board="$1"
|
|
|
|
case "$board" in
|
|
checkpoint,l-50)
|
|
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5 lan6 lan7 lan8 dmz" "eth0"
|
|
;;
|
|
cisco,on100)
|
|
ucidef_set_interface_lan "eth0 eth1"
|
|
;;
|
|
cloudengines,pogoe02|\
|
|
cloudengines,pogoplugv4|\
|
|
ctera,c200-v1|\
|
|
globalscale,sheevaplug|\
|
|
iom,iconnect-1.1|\
|
|
iom,ix2-200|\
|
|
iptime,nas1|\
|
|
netgear,readynas-duo-v2|\
|
|
raidsonic,ib-nas62x0|\
|
|
seagate,blackarmor-nas220|\
|
|
seagate,dockstar|\
|
|
seagate,goflexhome|\
|
|
seagate,goflexnet|\
|
|
zyxel,nsa310b|\
|
|
zyxel,nsa310s|\
|
|
zyxel,nsa325)
|
|
ucidef_set_interface_lan "eth0" "dhcp"
|
|
;;
|
|
endian,4i-edge-200)
|
|
ucidef_set_interface_lan "port1 port2 port3 port4 eth1"
|
|
;;
|
|
iom,ix4-200d)
|
|
ucidef_set_interface_lan "eth0 eth1" "dhcp"
|
|
;;
|
|
linksys,e4200-v2|\
|
|
linksys,ea3500|\
|
|
linksys,ea4500)
|
|
ucidef_set_interfaces_lan_wan "ethernet1 ethernet2 ethernet3 ethernet4" "internet"
|
|
;;
|
|
*)
|
|
ucidef_set_interface_lan "eth0"
|
|
;;
|
|
esac
|
|
}
|
|
|
|
kirkwood_setup_macs()
|
|
{
|
|
local board="$1"
|
|
local lan_mac=""
|
|
local wan_mac=""
|
|
local label_mac=""
|
|
|
|
case "$board" in
|
|
iptime,nas1)
|
|
lan_mac=$(mtd_get_mac_binary u-boot 0x3ffa8)
|
|
label_mac=$lan_mac
|
|
;;
|
|
linksys,e4200-v2|\
|
|
linksys,ea3500|\
|
|
linksys,ea4500)
|
|
wan_mac=$(mtd_get_mac_ascii u_env eth1addr)
|
|
;;
|
|
zyxel,nsa310b|\
|
|
zyxel,nsa325)
|
|
lan_mac=$(mtd_get_mac_ascii uboot_env ethaddr)
|
|
;;
|
|
esac
|
|
|
|
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
|
|
[ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac
|
|
[ -n "$label_mac" ] && ucidef_set_label_macaddr $label_mac
|
|
}
|
|
|
|
board_config_update
|
|
board=$(board_name)
|
|
kirkwood_setup_interfaces $board
|
|
kirkwood_setup_macs $board
|
|
board_config_flush
|
|
|
|
exit 0
|