0
0
mirror of https://git.openwrt.org/openwrt/openwrt.git synced 2025-02-24 08:25:03 +00:00
openwrt/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-a62.dts
Sven Eckelmann 087a8e39be ipq40xx: utilize nvmem-cells for openmesh,a62
The calibration data and mac addresses on this device are stored in the
0:ART partition. It is therefore possible to move the code to handle them
directly to the devicetree instead of the various scripts.

But the actual relevant information about the partition layout is provided
by the bootloader via bootargs (mtdparts) and not via the devicetree
itself. Instead of using a fixed-partition template, the mtd dynamic
partitions support from the upstream kernel is used.

Reported-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Tested-by: Michaël BILCOT <michael.bilcot@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-11-12 18:15:55 +01:00

270 lines
4.6 KiB
Plaintext

// SPDX-License-Identifier: ISC
/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
* Copyright (c) 2017-2018, Sven Eckelmann <sven.eckelmann@openmesh.com>
*/
#include "qcom-ipq4019.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/soc/qcom,tcsr.h>
/ {
model = "OpenMesh A62";
compatible = "openmesh,a62";
soc {
rng@22000 {
status = "okay";
};
tcsr@194b000 {
/* select hostmode */
compatible = "qcom,tcsr";
reg = <0x194b000 0x100>;
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
status = "okay";
};
tcsr@1949000 {
compatible = "qcom,tcsr";
reg = <0x1949000 0x100>;
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
};
ess_tcsr@1953000 {
compatible = "qcom,tcsr";
reg = <0x1953000 0x1000>;
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
};
tcsr@1957000 {
compatible = "qcom,tcsr";
reg = <0x1957000 0x100>;
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
};
usb2: usb2@60f8800 {
status = "okay";
};
crypto@8e3a000 {
status = "okay";
};
watchdog@b017000 {
status = "okay";
};
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART >;
};
};
aliases {
led-boot = &led_status_green;
led-failsafe = &led_status_green;
led-running = &led_status_green;
led-upgrade = &led_status_green;
label-mac-device = &swport4;
};
leds {
compatible = "gpio-leds";
status_red {
label = "red:status";
gpios = <&tlmm 43 GPIO_ACTIVE_HIGH>;
};
led_status_green: status_green {
label = "green:status";
gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
};
status_blue {
label = "blue:status";
gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>;
};
};
watchdog {
compatible = "linux,wdt-gpio";
gpios = <&tlmm 59 GPIO_ACTIVE_LOW>;
hw_algo = "toggle";
/* hw_margin_ms is actually 300s but driver limits it to 60s */
hw_margin_ms = <60000>;
always-running;
};
};
&tlmm {
serial_pins: serial_pinmux {
mux {
pins = "gpio16", "gpio17";
function = "blsp_uart0";
bias-disable;
};
};
spi_0_pins: spi_0_pinmux {
pin {
function = "blsp_spi0";
pins = "gpio13", "gpio14", "gpio15";
drive-strength = <12>;
bias-disable;
};
pin_cs {
function = "gpio";
pins = "gpio12";
drive-strength = <2>;
bias-disable;
output-high;
};
};
enable-usb-power {
gpio-hog;
gpios = <58 GPIO_ACTIVE_HIGH>;
output-low;
line-name = "enable USB2 power";
};
};
&blsp_dma {
status = "okay";
};
&blsp1_spi1 {
pinctrl-0 = <&spi_0_pins>;
pinctrl-names = "default";
status = "okay";
cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <24000000>;
/* partitions are passed via bootloader */
partitions {
partition-art {
compatible = "nvmem-cells";
#address-cells = <1>;
#size-cells = <1>;
label = "0:ART";
precal_art_1000: precal@1000 {
reg = <0x1000 0x2f20>;
};
precal_art_5000: precal@5000 {
reg = <0x5000 0x2f20>;
};
precal_art_9000: precal@9000 {
reg = <0x9000 0x2f20>;
};
macaddr_gmac0: macaddr@0 {
reg = <0x0 0x6>;
};
macaddr_gmac1: macaddr@6 {
reg = <0x6 0x6>;
};
};
};
};
};
&blsp1_uart1 {
pinctrl-0 = <&serial_pins>;
pinctrl-names = "default";
status = "okay";
};
&cryptobam {
status = "okay";
};
&usb2_hs_phy {
status = "okay";
};
&pcie0 {
status = "okay";
perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
bridge@0,0 {
reg = <0x00000000 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
ranges;
wifi2: wifi@1,0 {
compatible = "qcom,ath10k";
status = "okay";
reg = <0x00010000 0 0 0 0>;
qcom,ath10k-calibration-variant = "OM-A62";
ieee80211-freq-limit = <5170000 5350000>;
nvmem-cell-names = "pre-calibration";
nvmem-cells = <&precal_art_9000>;
};
};
};
&mdio {
status = "okay";
};
&gmac {
status = "okay";
};
&switch {
status = "okay";
};
&swport4 {
status = "okay";
label = "ethernet1";
nvmem-cell-names = "mac-address";
nvmem-cells = <&macaddr_gmac0>;
};
&swport5 {
status = "okay";
label = "ethernet2";
nvmem-cell-names = "mac-address";
nvmem-cells = <&macaddr_gmac1>;
};
&wifi0 {
status = "okay";
qcom,ath10k-calibration-variant = "OM-A62";
nvmem-cell-names = "pre-calibration";
nvmem-cells = <&precal_art_1000>;
};
&wifi1 {
status = "okay";
qcom,ath10k-calibration-variant = "OM-A62";
ieee80211-freq-limit = <5470000 5875000>;
nvmem-cell-names = "pre-calibration";
nvmem-cells = <&precal_art_5000>;
};