mirror of
https://git.openwrt.org/openwrt/openwrt.git
synced 2024-11-25 06:26:15 +00:00
0b078f2ecf
There is no need to keep a version specific dts directory. Rename the folder to its standard location. Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
142 lines
2.4 KiB
Plaintext
142 lines
2.4 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later
|
|
|
|
#include "rtl838x.dtsi"
|
|
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
/ {
|
|
compatible = "allnet,all-sg8208m", "realtek,rtl838x-soc";
|
|
model = "ALLNET ALL-SG8208M";
|
|
|
|
aliases {
|
|
led-boot = &led_sys;
|
|
led-failsafe = &led_sys;
|
|
led-running = &led_sys;
|
|
led-upgrade = &led_sys;
|
|
};
|
|
|
|
memory@0 {
|
|
device_type = "memory";
|
|
reg = <0x0 0x8000000>;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys-polled";
|
|
poll-interval = <20>;
|
|
|
|
/* is this pin 3 on the external RTL8231 (&gpio1)? */
|
|
/*reset {
|
|
label = "reset";
|
|
gpios = <&gpio0 67 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};*/
|
|
};
|
|
|
|
leds {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinmux_disable_sys_led>;
|
|
compatible = "gpio-leds";
|
|
|
|
led_sys: sys {
|
|
label = "green:sys";
|
|
gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
// GPIO 25: power on/off all port leds
|
|
};
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <10000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x80000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@80000 {
|
|
label = "u-boot-env";
|
|
reg = <0x80000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@90000 {
|
|
label = "u-boot-env2";
|
|
reg = <0x90000 0x10000>;
|
|
};
|
|
|
|
partition@a0000 {
|
|
label = "jffs";
|
|
reg = <0xa0000 0x100000>;
|
|
};
|
|
|
|
partition@1a0000 {
|
|
label = "jffs2";
|
|
reg = <0x1a0000 0x100000>;
|
|
};
|
|
|
|
partition@2a0000 {
|
|
label = "firmware";
|
|
reg = <0x2a0000 0xd60000>;
|
|
compatible = "openwrt,uimage", "denx,uimage";
|
|
openwrt,ih-magic = <0x00000006>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
ðernet0 {
|
|
mdio: mdio-bus {
|
|
compatible = "realtek,rtl838x-mdio";
|
|
regmap = <ðernet0>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
INTERNAL_PHY(8)
|
|
INTERNAL_PHY(9)
|
|
INTERNAL_PHY(10)
|
|
INTERNAL_PHY(11)
|
|
INTERNAL_PHY(12)
|
|
INTERNAL_PHY(13)
|
|
INTERNAL_PHY(14)
|
|
INTERNAL_PHY(15)
|
|
};
|
|
};
|
|
|
|
&switch0 {
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
SWITCH_PORT(8, 1, internal)
|
|
SWITCH_PORT(9, 2, internal)
|
|
SWITCH_PORT(10, 3, internal)
|
|
SWITCH_PORT(11, 4, internal)
|
|
SWITCH_PORT(12, 5, internal)
|
|
SWITCH_PORT(13, 6, internal)
|
|
SWITCH_PORT(14, 7, internal)
|
|
SWITCH_PORT(15, 8, internal)
|
|
|
|
port@28 {
|
|
ethernet = <ðernet0>;
|
|
reg = <28>;
|
|
phy-mode = "internal";
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
};
|
|
};
|