mirror of
https://git.openwrt.org/openwrt/openwrt.git
synced 2024-11-22 04:56:15 +00:00
732f539fb7
Hardware information: --------------------- - SoC: RTL8393M - Copper phy: 6×RTL8218B - Fibre phy: RTL8214FC - Flash: 32MiB SPI NOR, MX25L25635FMI - RAM: 128MiB DDR3, Micron MT41K64M16TW-107 - Serial port: ±5V serial port to RJ45, ZT3232 (MAX3232 compatible) - +370W POE on JG928A model Note: SFP ports currently non-functional due to missing support for RTL8214FC on the RTL8393M target. Updated for Linux 6.6 kernel. Installation: ------------- - Initial installation follows same process as HPE 1920-24G (JG924A) - Based on prior work of Jan Hoffmann <jan@3e8.eu> - Additional work by Andreas Böhler <dev@aboehler.at> - PoE updates and tidy-up by Stephen Howell <howels@allthatwemight.be> Signed-off-by: Stephen Howell <howels@allthatwemight.be>
113 lines
2.2 KiB
Plaintext
113 lines
2.2 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "rtl838x.dtsi"
|
|
#include "rtl83xx_hpe_1920.dtsi"
|
|
|
|
/ {
|
|
gpio1: rtl8231-gpio {
|
|
compatible = "realtek,rtl8231-gpio";
|
|
#gpio-cells = <2>;
|
|
gpio-controller;
|
|
indirect-access-bus-id = <0>;
|
|
};
|
|
|
|
i2c0: i2c-gpio-0 {
|
|
compatible = "i2c-gpio";
|
|
sda-gpios = <&gpio1 23 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
scl-gpios = <&gpio1 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
i2c-gpio,delay-us = <2>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
};
|
|
|
|
sfp0: sfp-0 {
|
|
compatible = "sff,sfp";
|
|
i2c-bus = <&i2c0>;
|
|
los-gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
|
|
mod-def0-gpio = <&gpio1 25 GPIO_ACTIVE_LOW>;
|
|
// tx-fault and tx-disable unconnected
|
|
};
|
|
|
|
i2c1: i2c-gpio-1 {
|
|
compatible = "i2c-gpio";
|
|
sda-gpios = <&gpio1 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
scl-gpios = <&gpio1 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
i2c-gpio,delay-us = <2>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
};
|
|
|
|
sfp1: sfp-1 {
|
|
compatible = "sff,sfp";
|
|
i2c-bus = <&i2c1>;
|
|
los-gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
|
|
mod-def0-gpio = <&gpio1 21 GPIO_ACTIVE_LOW>;
|
|
// tx-fault and tx-disable unconnected
|
|
};
|
|
};
|
|
|
|
ðernet0 {
|
|
mdio: mdio-bus {
|
|
compatible = "realtek,rtl838x-mdio";
|
|
regmap = <ðernet0>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
INTERNAL_PHY(8)
|
|
INTERNAL_PHY(9)
|
|
INTERNAL_PHY(10)
|
|
INTERNAL_PHY(11)
|
|
INTERNAL_PHY(12)
|
|
INTERNAL_PHY(13)
|
|
INTERNAL_PHY(14)
|
|
INTERNAL_PHY(15)
|
|
|
|
INTERNAL_PHY(24)
|
|
INTERNAL_PHY(26)
|
|
};
|
|
};
|
|
|
|
&switch0 {
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
SWITCH_PORT(8, 1, internal)
|
|
SWITCH_PORT(9, 2, internal)
|
|
SWITCH_PORT(10, 3, internal)
|
|
SWITCH_PORT(11, 4, internal)
|
|
SWITCH_PORT(12, 5, internal)
|
|
SWITCH_PORT(13, 6, internal)
|
|
SWITCH_PORT(14, 7, internal)
|
|
SWITCH_PORT(15, 8, internal)
|
|
|
|
port@24 {
|
|
reg = <24>;
|
|
label = "lan9";
|
|
phy-handle = <&phy24>;
|
|
phy-mode = "1000base-x";
|
|
managed = "in-band-status";
|
|
sfp = <&sfp0>;
|
|
};
|
|
|
|
port@26 {
|
|
reg = <26>;
|
|
label = "lan10";
|
|
phy-handle = <&phy26>;
|
|
phy-mode = "1000base-x";
|
|
managed = "in-band-status";
|
|
sfp = <&sfp1>;
|
|
};
|
|
|
|
port@28 {
|
|
ethernet = <ðernet0>;
|
|
reg = <28>;
|
|
phy-mode = "internal";
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
};
|
|
};
|