mirror of
https://git.openwrt.org/openwrt/openwrt.git
synced 2024-11-25 22:46:15 +00:00
fea2264d9f
Specifications:
- Device: DNA Valokuitu Plus EX400
- SoC: MT7621A
- Flash: 256MB NAND
- RAM: 256MB
- Ethernet: Built-in, 2 x 1GbE
- Wifi: MT7603 2.4 GHz, MT7615 5 GHz (4x internal antennas)
- USB: 1x 3.0
- LED: 1x green/red, 1x green
- Buttons: Reset
MAC addresses:
- LAN: u-boot 'ethaddr' (label)
- WAN: label + 1
- 2.4 GHz: label + 6
- 5 GHz: label + 7
Serial:
There is a black block connector next to the red ethernet connector. It
is accessible also through holes in the casing.
Pinout (TTL 3.3V)
+---+---+
|Tx |Rx |
+---+---+
|Vcc|Gnd|
+---+---+
Firmware:
The vendor firmware is a fork of OpenWrt (Reboot) with a kernel version
4.4.93. The flash is arranged as below and there is a dual boot
mechanism alternating between rootfs_0 and rootfs_1.
+-------+------+------+-----------+-----------+
| | env1 | env2 | rootfs_0 | rootfs_1 |
| +------+------+-----------+-----------+
| | UBI volumes |
+-------+-------------------------------------+
|U-Boot | UBI |
+-------+-------------------------------------+
|mtd0 | mtd1 |
+-------+-------------------------------------+
| NAND |
+---------------------------------------------+
In OpenWrt rootfs_0 will be used as a boot partition that will contain the
kernel and the dtb. The squashfs rootfs and overlay are standard OpenWrt
behaviour.
+-------+------+------+-----------+--------+------------+
| | env1 | env2 | rootfs_0 | rootfs | rootfs_data|
| +------+------+-----------+--------+------------+
| | UBI volumes |
+-------+-----------------------------------------------+
|U-Boot | UBI |
+-------+-----------------------------------------------+
|mtd0 | mtd1 |
+-------+-----------------------------------------------+
| NAND |
+-------------------------------------------------------+
U-boot:
With proper serial access booting can be halted to U-boot by pressing any
key. TFTP and flash writes are available, but only the first one has been
tested.
NOTE: Recovery mode can be accessed by holding down the reset button while
powering on the device. The led 'Update' will show a solid green light
once ready. A web server will be running at 192.168.1.1:80 and it will
allow flashing a firmware package. You can cycle between rootfs_0 and
rootfs_1 by pressing the reset button once.
Root password:
With the vendor web UI create a backup of your settings and download the
archive to your computer. Within the archive in the file
/etc/shadow replace the password hash for root with that of a password you
know. Restore the configuration with the vendor web UI and you will have
changed the root password.
SSH access:
You might need to enable the SSH service for LAN interface as by default
it's enabled for WAN only.
Installing OpenWrt:
With the vendor web UI install the OpenWrt factory image. Alternatively,
ssh to the device and use sysupgrade -n from cli.
Finalize by installing the OpenWrt sysupgrade image to get a fully
functioning system.
Reverting to the vendor firmware:
Boot with OpenWrt initramfs image
- Remove volumes rootfs_0, rootfs and rootfs_data and create vendor
volumes.
ubirmvol /dev/ubi0 -n 2
ubirmvol /dev/ubi0 -n 3
ubirmvol /dev/ubi0 -n 4
ubimkvol /dev/ubi0 -N rootfs_0 -S 990
ubimkvol /dev/ubi0 -N rootfs_1 -S 990
Power off and enter to the U-boot recovery to install the vendor
firmware.
Known issues:
- MACs for wifi are stored in currently unknown place but it seems
to persist over power-off. They might be stored on the chip.
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
[rmilecki: try NVMEM for MACs]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
52 lines
1.5 KiB
Bash
Executable File
52 lines
1.5 KiB
Bash
Executable File
#!/bin/sh /etc/rc.common
|
|
|
|
START=99
|
|
|
|
boot() {
|
|
case $(board_name) in
|
|
alfa-network,quad-e4g)
|
|
[ -n "$(fw_printenv bootcount bootchanged 2>/dev/null)" ] &&\
|
|
echo -e "bootcount\nbootchanged\n" | /usr/sbin/fw_setenv -s -
|
|
;;
|
|
beeline,smartbox-turbo|\
|
|
beeline,smartbox-turbo-plus|\
|
|
rostelecom,rt-sf-1)
|
|
[[ $(hexdump -n 1 -e '/1 "%1d"' -s $((0x20001)) /dev/mtd3) == \
|
|
$((0xff)) ]] || printf '\xff' | dd of=/dev/mtdblock3 \
|
|
count=1 bs=1 seek=$((0x20001))
|
|
;;
|
|
jdcloud,re-cp-02)
|
|
echo -e "bootcount 0\nbootlimit 5\nupgrade_available 1" | /usr/sbin/fw_setenv -s -
|
|
;;
|
|
linksys,e5600|\
|
|
linksys,ea6350-v4|\
|
|
linksys,ea7300-v1|\
|
|
linksys,ea7300-v2|\
|
|
linksys,ea7500-v2|\
|
|
linksys,ea8100-v1|\
|
|
linksys,ea8100-v2)
|
|
mtd resetbc s_env || true
|
|
;;
|
|
belkin,rt1800|\
|
|
linksys,e7350|\
|
|
samknows,whitebox-v8)
|
|
fw_setenv bootcount 0
|
|
;;
|
|
dna,valokuitu-plus-ex400)
|
|
fw_setenv boot_cnt_primary 0
|
|
fw_setenv boot_cnt_alt 0
|
|
;;
|
|
zyxel,lte3301-plus)
|
|
[ $(printf %d $(fw_printenv -n DebugFlag)) -gt 0 ] || fw_setenv DebugFlag 1
|
|
[ $(printf %d $(fw_printenv -n Image1Stable)) -gt 0 ] || fw_setenv Image1Stable 1
|
|
[ $(printf %d $(fw_printenv -n Image1Try)) -gt 0 ] && fw_setenv Image1Try 0
|
|
;;
|
|
zyxel,lte5398-m904|\
|
|
zyxel,nr7101)
|
|
[ $(printf %d $(fw_printenv -n DebugFlag)) -gt 0 ] || fw_setenv DebugFlag 0x1
|
|
[ $(printf %d $(fw_printenv -n Image1Stable)) -gt 0 ] || fw_setenv Image1Stable 1
|
|
[ $(printf %d $(fw_printenv -n Image1Try)) -gt 0 ] && fw_setenv Image1Try 0
|
|
;;
|
|
esac
|
|
}
|