mirror of
https://git.openwrt.org/openwrt/openwrt.git
synced 2024-11-22 04:56:15 +00:00
01996b785d
The previous NVMEM eeprom conversions[1][2] left a lot of partition labels that were no longer used. They can be removed now. [1] https://github.com/openwrt/openwrt/pull/13584 [2] https://github.com/openwrt/openwrt/pull/13587 Signed-off-by: Shiji Yang <yangshiji66@qq.com>
132 lines
2.6 KiB
Plaintext
132 lines
2.6 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "mt7621.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200n8";
|
|
};
|
|
|
|
keys: keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&nand {
|
|
status = "okay";
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "Bootloader";
|
|
reg = <0x0 0x80000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@80000 {
|
|
label = "Config";
|
|
reg = <0x80000 0x40000>;
|
|
};
|
|
|
|
partition@c0000 {
|
|
label = "Bdata";
|
|
reg = <0xc0000 0x40000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@100000 {
|
|
label = "factory";
|
|
reg = <0x100000 0x40000>;
|
|
read-only;
|
|
|
|
nvmem-layout {
|
|
compatible = "fixed-layout";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
eeprom_factory_0: eeprom@0 {
|
|
reg = <0x0 0x400>;
|
|
};
|
|
|
|
eeprom_factory_8000: eeprom@8000 {
|
|
reg = <0x8000 0x200>;
|
|
};
|
|
|
|
macaddr_factory_e000: macaddr@e000 {
|
|
reg = <0xe000 0x6>;
|
|
};
|
|
|
|
macaddr_factory_e006: macaddr@e006 {
|
|
reg = <0xe006 0x6>;
|
|
};
|
|
};
|
|
};
|
|
|
|
partition@140000 {
|
|
label = "crash";
|
|
reg = <0x140000 0x40000>;
|
|
};
|
|
|
|
partition@180000 {
|
|
label = "crash_syslog";
|
|
reg = <0x180000 0x40000>;
|
|
};
|
|
|
|
partition@1c0000 {
|
|
label = "reserved0";
|
|
reg = <0x1c0000 0x40000>;
|
|
read-only;
|
|
};
|
|
|
|
/* uboot expects to find kernels at 0x200000 & 0x600000
|
|
* referred to as system 1 & system 2 respectively.
|
|
* a kernel is considered suitable for handing control over
|
|
* if its linux magic number exists & uImage CRC are correct.
|
|
* If either of those conditions fail, a matching sys'n'_fail flag
|
|
* is set in uboot env & a restart performed in the hope that the
|
|
* alternate kernel is okay.
|
|
* if neither kernel checksums ok and both are marked failed, system 2
|
|
* is booted anyway.
|
|
*
|
|
* Note uboot's tftp flash install writes the transferred
|
|
* image to both kernel partitions.
|
|
*/
|
|
|
|
/* We keep stock xiaomi firmware (kernel0) here */
|
|
partition@200000 {
|
|
label = "kernel_stock";
|
|
reg = <0x200000 0x400000>;
|
|
};
|
|
|
|
partition@600000 {
|
|
label = "kernel";
|
|
reg = <0x600000 0x400000>;
|
|
};
|
|
|
|
/* ubi partition is the result of squashing
|
|
* next consecutive stock partitions:
|
|
* - rootfs0 (rootfs partition for stock kernel0),
|
|
* - rootfs1 (rootfs partition for stock failsafe kernel1),
|
|
* - overlay (used as ubi overlay in stock fw)
|
|
* resulting 117,5MiB space for packages.
|
|
*/
|
|
|
|
partition@a00000 {
|
|
label = "ubi";
|
|
reg = <0xa00000 0x7580000>;
|
|
};
|
|
};
|
|
};
|