mirror of
https://git.openwrt.org/openwrt/openwrt.git
synced 2024-11-24 14:06:15 +00:00
102009f3ea
with 6.1, the kernel no longer fitted into the 16 MiB and kicking down the can and increasing KERNEL_SIZE to 20 MiB didn't help as the device failed to boot. Using 'kernel-bin | gzip | uimage gzip' didn't work since the uboot does not have enough heap to decompress these big kernels. And finally playing around with uboot was more a hassle than converting this device to take the simpleImage-boot-route in the future. Note: The device now takes even longer on the first boot-up after the flash due to JFFS2 initializing all the remaining flash. Be prepared to wait up to 10 minutes before the green status LED stops blinking and will shine a solid green! (On the plus site: the device now has ~10 MiB of additional space for rootfs+rootfs_data). Note2: This patch includes a kernel patch refresh. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
425 lines
9.3 KiB
Plaintext
425 lines
9.3 KiB
Plaintext
/*
|
|
* Aerohive HiveAP-330 Device Tree Source
|
|
*
|
|
* Copyright (C) 2017 Chris Blake <chrisrblake93@gmail.com>
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify it
|
|
* under the terms of the GNU General Public License as published by the
|
|
* Free Software Foundation; either version 2 of the License, or (at your
|
|
* option) any later version.
|
|
*/
|
|
|
|
#include <dt-bindings/leds/common.h>
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
/include/ "fsl/p1020si-pre.dtsi"
|
|
/ {
|
|
model = "Aerohive HiveAP-330";
|
|
compatible = "aerohive,hiveap-330";
|
|
|
|
aliases {
|
|
led-boot = &led_power_green;
|
|
led-failsafe = &led_fault_red;
|
|
led-running = &led_power_green;
|
|
led-upgrade = &led_fault_red;
|
|
label-mac-device = &enet0;
|
|
spi0 = &spi0;
|
|
};
|
|
|
|
chosen {
|
|
/*
|
|
* not yet implemented.
|
|
* stdout-path = &serial0 ":9600n8";
|
|
* <https://www.spinics.net/lists/devicetree-compiler/msg02487.html>
|
|
*
|
|
* this should work... but it doesn't because CONFIG_CMDLINE in our
|
|
* OpenWrt's target config sets "console=ttyS0,115200"
|
|
* stdout-path = "/soc@ffe00000/serial@4500:9600n8";
|
|
*/
|
|
|
|
bootargs = "console=ttyS0,9600n8";
|
|
};
|
|
|
|
cpus {
|
|
PowerPC,P1020@0 {
|
|
i-cache-sets = <0x80>;
|
|
i-cache-size = <0x8000>;
|
|
i-cache-block-size = <0x20>;
|
|
d-cache-sets = <0x80>;
|
|
d-cache-size = <0x8000>;
|
|
d-cache-block-size = <0x20>;
|
|
status = "okay";
|
|
clock-frequency = <533333328>; /* 533.33 MHz */
|
|
bus-frequency = <266666664>; /* 266.66 MHz */
|
|
timebase-frequency = <33333333>; /* 33.33 MHz */
|
|
};
|
|
|
|
PowerPC,P1020@1 {
|
|
i-cache-sets = <0x80>;
|
|
i-cache-size = <0x8000>;
|
|
i-cache-block-size = <0x20>;
|
|
d-cache-sets = <0x80>;
|
|
d-cache-size = <0x8000>;
|
|
d-cache-block-size = <0x20>;
|
|
cpu-release-addr = <0x00 0xffff240>;
|
|
enable-method = "spin-table";
|
|
status = "disabled";
|
|
clock-frequency = <533333328>;
|
|
bus-frequency = <266666664>;
|
|
timebase-frequency = <33333333>;
|
|
};
|
|
};
|
|
|
|
memory {
|
|
#address-cells = <2>;
|
|
#size-cells = <2>;
|
|
|
|
reg = <0x00 0x00 0x00 0x10000000>;
|
|
device_type = "memory";
|
|
};
|
|
|
|
/*
|
|
* Usually, u-boot provided /memreserve/ properties by adding them during boot.
|
|
* these have been converted to reserved-memory entries.
|
|
*/
|
|
reserved-memory {
|
|
#address-cells = <2>;
|
|
#size-cells = <2>;
|
|
ranges;
|
|
|
|
/*
|
|
* /memreserve/ 0x0000000000ffa000 0x0000000000004000;
|
|
* The kernel complains when booting:
|
|
*
|
|
* | OF: fdt: Reserved memory: failed to reserve memory for node
|
|
* 'firmware@ffa000': base 0x00ffa000, size 0 MiB
|
|
*
|
|
* But this likely uboot's bootargs + modified DTB. And if so, we don't care.
|
|
* This is because we rely on our own dtb that's in the simpleImage.
|
|
*
|
|
* Note: This is backed up by u-boot. just before the kernel executes
|
|
* it prints this final line:
|
|
* | Loading Device Tree to 00ff9000, end 00fff1c4 ... OK
|
|
*
|
|
* firmware@ffa000 {
|
|
* reg = <0x0 0xffa000 0x0 0x4000>;
|
|
* no-map;
|
|
* };
|
|
*/
|
|
|
|
// /memreserve/ 0x000000000fe2f000 0x0000000000000021;
|
|
firmware@fe2f000 {
|
|
reg = <0x0 0xfe2f000 0x0 0x21>;
|
|
no-map;
|
|
};
|
|
|
|
/*
|
|
* /memreserve/ 0x000000000ffff000 0x0000000000001000;
|
|
* that's the spin-table - see second CPU core binding.
|
|
*/
|
|
firmware@ffff000 {
|
|
reg = <0x0 0xffff000 0x0 0x1000>;
|
|
no-map;
|
|
};
|
|
};
|
|
|
|
board_lbc: lbc: localbus@ffe05000 {
|
|
bus-frequency = <16666666>; /* 16.66 MHz */
|
|
reg = <0 0xffe05000 0 0x1000>;
|
|
ranges = <0x0 0x0 0x0 0xec000000 0x4000000>;
|
|
|
|
nor@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "cfi-flash";
|
|
reg = <0x0 0x0 0x4000000>;
|
|
bank-width = <2>;
|
|
device-width = <1>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
firmware@0 {
|
|
reg = <0x0 0x3f00000>;
|
|
label = "firmware";
|
|
/*
|
|
* This unknown/invalid compatible prevents
|
|
* openwrt's mtdsplit_fit to go off a tangent if it
|
|
* finds a magic value inside the uncompressed kernel
|
|
* at a blocksized aligned place.
|
|
*/
|
|
compatible = "areohive,hiveap-330-image";
|
|
};
|
|
|
|
partition@0 {
|
|
reg = <0x0 0x40000>;
|
|
label = "dtb";
|
|
};
|
|
|
|
partition@40000 {
|
|
compatible = "openwrt,uimage", "denx,uimage";
|
|
reg = <0x40000 0x3ec0000>;
|
|
label = "kernel";
|
|
};
|
|
|
|
partition@3f00000 {
|
|
reg = <0x3f00000 0x20000>;
|
|
label = "hw-info";
|
|
read-only;
|
|
|
|
nvmem-layout {
|
|
compatible = "fixed-layout";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
macaddr_hwinfo_0: macaddr@0 {
|
|
compatible = "mac-base";
|
|
reg = <0x0 0x6>;
|
|
#nvmem-cell-cells = <1>;
|
|
};
|
|
};
|
|
};
|
|
|
|
partition@3f20000 {
|
|
reg = <0x3f20000 0x20000>;
|
|
label = "boot-info";
|
|
read-only;
|
|
};
|
|
|
|
partition@3f40000 {
|
|
reg = <0x3f40000 0x20000>;
|
|
label = "boot-info-backup";
|
|
read-only;
|
|
};
|
|
|
|
partition@3f60000 {
|
|
reg = <0x3f60000 0x20000>;
|
|
label = "u-boot-env";
|
|
};
|
|
|
|
partition@3f80000 {
|
|
reg = <0x3f80000 0x80000>;
|
|
label = "u-boot";
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
board_soc: soc: soc@ffe00000 {
|
|
ranges = <0x0 0x0 0xffe00000 0x100000>;
|
|
bus-frequency = <266666664>;
|
|
|
|
spi0: spi@7000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
temperature-sensor@1 {
|
|
compatible = "ti,tmp125";
|
|
reg = <1>;
|
|
spi-max-frequency = <5000000>;
|
|
};
|
|
};
|
|
|
|
i2c@3100 {
|
|
tpm@29 {
|
|
compatible = "atmel,at97sc3204t";
|
|
reg = <0x29>;
|
|
};
|
|
|
|
lp5521@32 {
|
|
compatible = "national,lp5521";
|
|
reg = <0x32>;
|
|
clock-mode = /bits/ 8 <2>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
#if 1
|
|
led_fault_red: led@0 {
|
|
reg = <0>;
|
|
chan-name = "fault:red";
|
|
led-cur = /bits/ 8 <0x2f>;
|
|
max-cur = /bits/ 8 <0x5f>;
|
|
color = <LED_COLOR_ID_RED>;
|
|
function = LED_FUNCTION_FAULT;
|
|
};
|
|
led_power_green: led@1 {
|
|
reg = <1>;
|
|
chan-name = "power:green";
|
|
led-cur = /bits/ 8 <0x2f>;
|
|
max-cur = /bits/ 8 <0x5f>;
|
|
color = <LED_COLOR_ID_GREEN>;
|
|
function = LED_FUNCTION_POWER;
|
|
};
|
|
led@2{
|
|
reg = <2>;
|
|
chan-name = "blue";
|
|
led-cur = /bits/ 8 <0x2f>;
|
|
max-cur = /bits/ 8 <0x5f>;
|
|
color = <LED_COLOR_ID_BLUE>;
|
|
};
|
|
#else
|
|
/*
|
|
* openwrt isn't ready to handle multi-intensity leds yet
|
|
* # echo 255 255 255 > /sys/class/leds/tricolor/multi_intensity
|
|
* # echo 255 > /sys/class/leds/tricolor/brightness
|
|
*/
|
|
|
|
rgbled-0 {
|
|
function = LED_FUNCTION_POWER;
|
|
color = <LED_COLOR_ID_RGB>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
led@0 {
|
|
reg = <0>;
|
|
chan-name = "tricolor";
|
|
led-cur = /bits/ 8 <0x2f>;
|
|
max-cur = /bits/ 8 <0x5f>;
|
|
color = <LED_COLOR_ID_RED>;
|
|
};
|
|
led@1 {
|
|
reg = <1>;
|
|
chan-name = "tricolor";
|
|
led-cur = /bits/ 8 <0x2f>;
|
|
max-cur = /bits/ 8 <0x5f>;
|
|
color = <LED_COLOR_ID_GREEN>;
|
|
};
|
|
led@2{
|
|
reg = <2>;
|
|
chan-name = "tricolor";
|
|
led-cur = /bits/ 8 <0x2f>;
|
|
max-cur = /bits/ 8 <0x5f>;
|
|
color = <LED_COLOR_ID_BLUE>;
|
|
};
|
|
};
|
|
#endif
|
|
};
|
|
|
|
eeprom@51 {
|
|
/*
|
|
* 1Kbit I2C/SMBus EEPROM with SHA-1 Engine
|
|
* Aerohive calls it "dallas".
|
|
*/
|
|
compatible = "adi,ds28cn01";
|
|
reg = <0x51>;
|
|
read-only;
|
|
};
|
|
};
|
|
|
|
mdio@24000 {
|
|
phy0: ethernet-phy@0 {
|
|
/* interrupts = <3 1 0 0>; */
|
|
reg = <0x1>;
|
|
};
|
|
|
|
phy1: ethernet-phy@1 {
|
|
/* interrupts = <2 1 0 0>; */
|
|
reg = <0x2>;
|
|
};
|
|
};
|
|
|
|
mdio@25000 {
|
|
status = "disabled";
|
|
};
|
|
|
|
mdio@26000 {
|
|
status = "disabled";
|
|
};
|
|
|
|
enet0: ethernet@b0000 {
|
|
rx-stash-idx = <0x00>;
|
|
rx-stash-len = <0x60>;
|
|
bd-stash;
|
|
status = "okay";
|
|
phy-handle = <&phy0>;
|
|
phy-connection-type = "rgmii-id";
|
|
nvmem-cells = <&macaddr_hwinfo_0 0>;
|
|
nvmem-cell-names = "mac-address";
|
|
};
|
|
|
|
enet1: ethernet@b1000 {
|
|
status = "disabled";
|
|
};
|
|
|
|
enet2: ethernet@b2000 {
|
|
rx-stash-idx = <0x00>;
|
|
rx-stash-len = <0x60>;
|
|
bd-stash;
|
|
status = "okay";
|
|
phy-handle = <&phy1>;
|
|
phy-connection-type = "rgmii-id";
|
|
nvmem-cells = <&macaddr_hwinfo_0 1>;
|
|
nvmem-cell-names = "mac-address";
|
|
};
|
|
|
|
gpio0: gpio-controller@fc00 {
|
|
};
|
|
|
|
usb@22000 {
|
|
phy_type = "ulpi";
|
|
dr_mode = "host";
|
|
};
|
|
|
|
usb@23000 {
|
|
status = "disabled";
|
|
};
|
|
};
|
|
|
|
pci0: pcie@ffe09000 {
|
|
reg = <0x0 0xffe09000 0x0 0x1000>;
|
|
ranges = <0x2000000 0x0 0xa0000000 0x0 0xa0000000 0x0 0x20000000>,
|
|
<0x1000000 0x0 0x00000000 0x0 0xffc30000 0x0 0x10000>;
|
|
pcie@0 {
|
|
ranges = <0x2000000 0x0 0xa0000000 0x2000000 0x0 0xa0000000 0x0 0x20000000>,
|
|
<0x1000000 0x0 0x00000000 0x1000000 0x0 0x00000000 0x0 0x00100000>;
|
|
};
|
|
};
|
|
|
|
pci1: pcie@ffe0a000 {
|
|
reg = <0x0 0xffe0a000 0x0 0x1000>;
|
|
ranges = <0x2000000 0x0 0xc0000000 0x0 0xc0000000 0x0 0x20000000>,
|
|
<0x1000000 0x0 0x00000000 0x0 0xffc20000 0x0 0x10000>;
|
|
|
|
pcie@0 {
|
|
ranges = <0x2000000 0x0 0xc0000000 0x2000000 0x0 0xc0000000 0x0 0x20000000>,
|
|
<0x1000000 0x0 0x00000000 0x1000000 0x0 0x00000000 0x0 0x00100000>;
|
|
};
|
|
};
|
|
|
|
buttons {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "Reset button";
|
|
gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
};
|
|
};
|
|
|
|
/include/ "fsl/p1020si-post.dtsi"
|
|
&serial0 {
|
|
clock-frequency = <266666664>;
|
|
};
|
|
|
|
&serial1 {
|
|
clock-frequency = <266666664>;
|
|
};
|
|
|
|
/*
|
|
* For the OpenWrt 22.03 release, since Linux 5.10.138 now uses
|
|
* aliases to determine PCI domain numbers, drop aliases so as not to
|
|
* change the sysfs path of our wireless netdevs.
|
|
*/
|
|
|
|
/ {
|
|
aliases {
|
|
/delete-property/ pci0;
|
|
/delete-property/ pci1;
|
|
};
|
|
};
|