mirror of
https://git.openwrt.org/openwrt/openwrt.git
synced 2024-11-22 13:06:14 +00:00
45b3c620e5
AC2400 Dual-Band Gigabit Wi-Fi Router base on ipq8064. https://www.linksys.com/support-product?sku=E8350 Specification: - Qualcomm dual-core IPQ8064 @ 1.4 GHz - 512 MB of RAM - 4 MB of SPI NOR MX25U3235F - 128 MB of NAND S34MS01G2 - Qualcomm QCA9880 2.4GHz 802.11bgn - Quantenna QSR1000 5GHz 802.11ac (no support) - 4 x 10/100/1000 Mbit/s w/ vlan support Ethernet - Qualcomm Atheros QCA8337 switch - 1 x 3.0 + 1 x 2.0 (combo with eSata port) - 115200, 8N1 internal serial console - Power, Reset, WPS and WLAN buttons - Power, WPS and WLAN leds - 12 VDC, 3 A power Installation: The installation must be done using web interface of the router. To achive this new firmware-utils tool was added to set correct magic headers for the factory images. Installation from vendor firmware: 1. Flash over the native Linksys WEB interface using factory image. Installation using recovery mode: 1. Power off the device and disconnect the WAN port. (Only LAN port to be connected) 2. Press & hold the "Reset" button 3. Power on the device & wait 10 seconds with pressed "Reset" button 4. Set IP Internet Protocol on your PC from 192.168.1.0/24 network (Router is on IP 192.168.1.1) 5. Open the Firmware Recovery page in your browser: http://192.168.1.1/index.shtml Firmware Recovery -> File Name -> Recovery & Reboot The device page in inbox: https://openwrt.org/inbox/toh/linksys/linksys_ea8350_1 Signed-off-by: Sergey Filippov <sergey.filippov@outlook.com> Link: https://github.com/openwrt/openwrt/pull/15798 Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
115 lines
2.7 KiB
Plaintext
115 lines
2.7 KiB
Plaintext
#
|
|
# Copyright (c) 2015 The Linux Foundation. All rights reserved.
|
|
# Copyright (c) 2011-2015 OpenWrt.org
|
|
#
|
|
|
|
. /lib/functions/uci-defaults.sh
|
|
. /lib/functions/system.sh
|
|
|
|
ipq806x_setup_interfaces()
|
|
{
|
|
local board="$1"
|
|
|
|
case "$board" in
|
|
arris,tr4400-v2)
|
|
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "eth2"
|
|
;;
|
|
askey,rt4230w-rev6 |\
|
|
asrock,g10 |\
|
|
nec,wg2600hp |\
|
|
buffalo,wxr-2533dhp |\
|
|
compex,wpq864 |\
|
|
netgear,d7800 |\
|
|
netgear,r7500 |\
|
|
netgear,r7500v2 |\
|
|
qcom,ipq8064-ap148 |\
|
|
linksys,e8350-v1 |\
|
|
linksys,ea7500-v1 |\
|
|
linksys,ea8500 |\
|
|
nec,wg2600hp3 |\
|
|
netgear,r7800 |\
|
|
netgear,xr500 |\
|
|
netgear,xr450 |\
|
|
tplink,c2600 |\
|
|
tplink,vr2600v |\
|
|
tplink,ad7200 |\
|
|
zyxel,nbg6817)
|
|
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
|
|
ucidef_set_network_device_conduit "lan1" "eth1"
|
|
ucidef_set_network_device_conduit "lan2" "eth1"
|
|
ucidef_set_network_device_conduit "lan3" "eth1"
|
|
ucidef_set_network_device_conduit "lan4" "eth1"
|
|
ucidef_set_network_device_conduit "wan" "eth0"
|
|
;;
|
|
asus,onhub |\
|
|
tplink,onhub)
|
|
ucidef_set_interfaces_lan_wan "lan1" "wan"
|
|
ucidef_set_network_device_conduit "lan1" "eth1"
|
|
ucidef_set_network_device_conduit "wan" "eth0"
|
|
;;
|
|
edgecore,ecw5410)
|
|
ucidef_set_interfaces_lan_wan "eth1" "eth0"
|
|
;;
|
|
qcom,ipq8064-ap161)
|
|
ucidef_set_interface_lan "eth1 eth2 lan1 lan2 lan3 lan4" "wan"
|
|
;;
|
|
qcom,ipq8064-db149)
|
|
ucidef_set_interface_lan "eth1 eth2 eth3 lan1 lan2 lan3 lan4" "wan"
|
|
;;
|
|
fortinet,fap-421e |\
|
|
ubnt,unifi-ac-hd)
|
|
ucidef_set_interface_lan "eth0 eth1"
|
|
;;
|
|
meraki,mr42)
|
|
ucidef_set_interface_lan "eth0"
|
|
;;
|
|
extreme,ap3935 |\
|
|
meraki,mr52)
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
;;
|
|
*)
|
|
echo "Unsupported hardware. Network interfaces not intialized"
|
|
;;
|
|
esac
|
|
}
|
|
|
|
ipq806x_setup_macs()
|
|
{
|
|
local board="$1"
|
|
|
|
case "$board" in
|
|
linksys,ea7500-v1)
|
|
hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr)
|
|
ucidef_set_interface_macaddr "lan" "$hw_mac_addr"
|
|
ucidef_set_interface_macaddr "wan" "$hw_mac_addr"
|
|
;;
|
|
linksys,ea8500)
|
|
hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr)
|
|
ucidef_set_interface_macaddr "lan" "$hw_mac_addr"
|
|
ucidef_set_interface_macaddr "wan" "$hw_mac_addr"
|
|
;;
|
|
linksys,e8350-v1 |\
|
|
zyxel,nbg6817)
|
|
hw_mac_addr=$(mtd_get_mac_ascii 0:appsblenv ethaddr)
|
|
ucidef_set_interface_macaddr "lan" "$(macaddr_add $hw_mac_addr 2)"
|
|
ucidef_set_interface_macaddr "wan" "$(macaddr_add $hw_mac_addr 3)"
|
|
;;
|
|
asrock,g10)
|
|
hw_mac_addr=$(mtd_get_mac_ascii hwconfig HW.LAN.MAC.Address)
|
|
ucidef_set_interface_macaddr "lan" "$hw_mac_addr"
|
|
hw_mac_addr=$(mtd_get_mac_ascii hwconfig HW.WAN.MAC.Address)
|
|
ucidef_set_interface_macaddr "wan" "$hw_mac_addr"
|
|
;;
|
|
esac
|
|
}
|
|
|
|
board_config_update
|
|
board=$(board_name)
|
|
|
|
ipq806x_setup_macs $board
|
|
ipq806x_setup_interfaces $board
|
|
|
|
board_config_flush
|
|
|
|
exit 0
|