mirror of
https://git.openwrt.org/openwrt/openwrt.git
synced 2024-11-24 14:06:15 +00:00
7b5aeef6db
Add support for Ubiquiti LiteBeam M5 (XW). The device was previously supported in ar71xx. See commit: https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=d0988235dd277b9a832bbc4b2a100ac6e821f577 Add ALTX_MODEL for Ubiquiti AirGrid M5 HP (XW), Ubiquiti PowerBeam M5 300 (XW) in generic-ubnt.mk This models are identical (firmware-wise) to the already supported Ubiquiti Nanostation Loco M (XW) Add also Ubiquiti NanoBeam M5 to ALTX_MODEL of Ubiquiti Nanostation Loco M (XW) since it's another clone. Tested on: - Ubiquiti LiteBeam M5 (XW) - Ubiquiti PowerBeam M5 (XW) This also modify target/ath79/dts/ar9342_ubnt_xw.dtsi to use nvmem for calibration data Checked that the caldata size in the eeprom partition are actually 0x440 on: - Ubiquiti PowerBeam M5 (XW) - Ubiquiti Nanostation M5 (XW) - Ubiquiti LiteBeam M5 (XW) - Ubiquiti AirGrid M5 HP (XW) Signed-off-by: Samuele Longhi <agave@dracaena.it>
60 lines
1.1 KiB
Plaintext
60 lines
1.1 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "ar9342_ubnt_xw.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/leds/common.h>
|
|
|
|
/ {
|
|
compatible = "ubnt,litebeam-m5-xw", "qca,ar9342";
|
|
model = "Ubiquiti LiteBeam M5 (XW)";
|
|
|
|
aliases {
|
|
led-boot = &led_status;
|
|
led-running = &led_status;
|
|
led-upgrade = &led_status;
|
|
led-failsafe = &led_status;
|
|
label-mac-device = &wmac;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led-lan {
|
|
color = <LED_COLOR_ID_GREEN>;
|
|
function = LED_FUNCTION_LAN;
|
|
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led-wlan {
|
|
color = <LED_COLOR_ID_GREEN>;
|
|
function = LED_FUNCTION_WLAN;
|
|
linux,default-trigger = "phy0tpt";
|
|
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led_status: led-power {
|
|
color = <LED_COLOR_ID_GREEN>;
|
|
function = LED_FUNCTION_POWER;
|
|
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy1: ethernet-phy@1 {
|
|
reg = <1>;
|
|
phy-mode = "mii";
|
|
reset-gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
phy-handle = <&phy1>;
|
|
};
|