forked from Openwrt/openwrt
7ace30aeb6
Backport upstream code split patch for qca8k needed for ipq40xx target to correctly implement a DSA driver. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
7390 lines
202 KiB
Diff
7390 lines
202 KiB
Diff
From 4bbaf764e1e1786eb937fdb62172f656f512e116 Mon Sep 17 00:00:00 2001
|
|
From: Christian Marangi <ansuelsmth@gmail.com>
|
|
Date: Wed, 13 Jul 2022 22:53:50 +0200
|
|
Subject: [PATCH 1/1] net: dsa: qca8k: move driver to qca dir
|
|
|
|
Move qca8k driver to qca dir in preparation for code split and
|
|
introduction of ipq4019 switch based on qca8k.
|
|
|
|
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
|
|
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
---
|
|
drivers/net/dsa/Kconfig | 8 --------
|
|
drivers/net/dsa/Makefile | 1 -
|
|
drivers/net/dsa/qca/Kconfig | 8 ++++++++
|
|
drivers/net/dsa/qca/Makefile | 1 +
|
|
drivers/net/dsa/{ => qca}/qca8k.c | 0
|
|
drivers/net/dsa/{ => qca}/qca8k.h | 0
|
|
6 files changed, 9 insertions(+), 9 deletions(-)
|
|
rename drivers/net/dsa/{ => qca}/qca8k.c (100%)
|
|
rename drivers/net/dsa/{ => qca}/qca8k.h (100%)
|
|
|
|
--- a/drivers/net/dsa/Kconfig
|
|
+++ b/drivers/net/dsa/Kconfig
|
|
@@ -60,14 +60,6 @@ source "drivers/net/dsa/sja1105/Kconfig"
|
|
|
|
source "drivers/net/dsa/xrs700x/Kconfig"
|
|
|
|
-config NET_DSA_QCA8K
|
|
- tristate "Qualcomm Atheros QCA8K Ethernet switch family support"
|
|
- select NET_DSA_TAG_QCA
|
|
- select REGMAP
|
|
- help
|
|
- This enables support for the Qualcomm Atheros QCA8K Ethernet
|
|
- switch chips.
|
|
-
|
|
config NET_DSA_REALTEK_SMI
|
|
tristate "Realtek SMI Ethernet switch family support"
|
|
select NET_DSA_TAG_RTL4_A
|
|
--- a/drivers/net/dsa/Makefile
|
|
+++ b/drivers/net/dsa/Makefile
|
|
@@ -8,7 +8,6 @@ endif
|
|
obj-$(CONFIG_NET_DSA_LANTIQ_GSWIP) += lantiq_gswip.o
|
|
obj-$(CONFIG_NET_DSA_MT7530) += mt7530.o
|
|
obj-$(CONFIG_NET_DSA_MV88E6060) += mv88e6060.o
|
|
-obj-$(CONFIG_NET_DSA_QCA8K) += qca8k.o
|
|
obj-$(CONFIG_NET_DSA_REALTEK_SMI) += realtek-smi.o
|
|
realtek-smi-objs := realtek-smi-core.o rtl8366.o rtl8366rb.o
|
|
obj-$(CONFIG_NET_DSA_SMSC_LAN9303) += lan9303-core.o
|
|
--- a/drivers/net/dsa/qca/Kconfig
|
|
+++ b/drivers/net/dsa/qca/Kconfig
|
|
@@ -7,3 +7,11 @@ config NET_DSA_AR9331
|
|
help
|
|
This enables support for the Qualcomm Atheros AR9331 built-in Ethernet
|
|
switch.
|
|
+
|
|
+config NET_DSA_QCA8K
|
|
+ tristate "Qualcomm Atheros QCA8K Ethernet switch family support"
|
|
+ select NET_DSA_TAG_QCA
|
|
+ select REGMAP
|
|
+ help
|
|
+ This enables support for the Qualcomm Atheros QCA8K Ethernet
|
|
+ switch chips.
|
|
--- a/drivers/net/dsa/qca/Makefile
|
|
+++ b/drivers/net/dsa/qca/Makefile
|
|
@@ -1,2 +1,3 @@
|
|
# SPDX-License-Identifier: GPL-2.0-only
|
|
obj-$(CONFIG_NET_DSA_AR9331) += ar9331.o
|
|
+obj-$(CONFIG_NET_DSA_QCA8K) += qca8k.o
|
|
--- /dev/null
|
|
+++ b/drivers/net/dsa/qca/qca8k.c
|
|
@@ -0,0 +1,3243 @@
|
|
+// SPDX-License-Identifier: GPL-2.0
|
|
+/*
|
|
+ * Copyright (C) 2009 Felix Fietkau <nbd@nbd.name>
|
|
+ * Copyright (C) 2011-2012 Gabor Juhos <juhosg@openwrt.org>
|
|
+ * Copyright (c) 2015, 2019, The Linux Foundation. All rights reserved.
|
|
+ * Copyright (c) 2016 John Crispin <john@phrozen.org>
|
|
+ */
|
|
+
|
|
+#include <linux/module.h>
|
|
+#include <linux/phy.h>
|
|
+#include <linux/netdevice.h>
|
|
+#include <linux/bitfield.h>
|
|
+#include <linux/regmap.h>
|
|
+#include <net/dsa.h>
|
|
+#include <linux/of_net.h>
|
|
+#include <linux/of_mdio.h>
|
|
+#include <linux/of_platform.h>
|
|
+#include <linux/if_bridge.h>
|
|
+#include <linux/mdio.h>
|
|
+#include <linux/phylink.h>
|
|
+#include <linux/gpio/consumer.h>
|
|
+#include <linux/etherdevice.h>
|
|
+#include <linux/dsa/tag_qca.h>
|
|
+
|
|
+#include "qca8k.h"
|
|
+
|
|
+#define MIB_DESC(_s, _o, _n) \
|
|
+ { \
|
|
+ .size = (_s), \
|
|
+ .offset = (_o), \
|
|
+ .name = (_n), \
|
|
+ }
|
|
+
|
|
+static const struct qca8k_mib_desc ar8327_mib[] = {
|
|
+ MIB_DESC(1, 0x00, "RxBroad"),
|
|
+ MIB_DESC(1, 0x04, "RxPause"),
|
|
+ MIB_DESC(1, 0x08, "RxMulti"),
|
|
+ MIB_DESC(1, 0x0c, "RxFcsErr"),
|
|
+ MIB_DESC(1, 0x10, "RxAlignErr"),
|
|
+ MIB_DESC(1, 0x14, "RxRunt"),
|
|
+ MIB_DESC(1, 0x18, "RxFragment"),
|
|
+ MIB_DESC(1, 0x1c, "Rx64Byte"),
|
|
+ MIB_DESC(1, 0x20, "Rx128Byte"),
|
|
+ MIB_DESC(1, 0x24, "Rx256Byte"),
|
|
+ MIB_DESC(1, 0x28, "Rx512Byte"),
|
|
+ MIB_DESC(1, 0x2c, "Rx1024Byte"),
|
|
+ MIB_DESC(1, 0x30, "Rx1518Byte"),
|
|
+ MIB_DESC(1, 0x34, "RxMaxByte"),
|
|
+ MIB_DESC(1, 0x38, "RxTooLong"),
|
|
+ MIB_DESC(2, 0x3c, "RxGoodByte"),
|
|
+ MIB_DESC(2, 0x44, "RxBadByte"),
|
|
+ MIB_DESC(1, 0x4c, "RxOverFlow"),
|
|
+ MIB_DESC(1, 0x50, "Filtered"),
|
|
+ MIB_DESC(1, 0x54, "TxBroad"),
|
|
+ MIB_DESC(1, 0x58, "TxPause"),
|
|
+ MIB_DESC(1, 0x5c, "TxMulti"),
|
|
+ MIB_DESC(1, 0x60, "TxUnderRun"),
|
|
+ MIB_DESC(1, 0x64, "Tx64Byte"),
|
|
+ MIB_DESC(1, 0x68, "Tx128Byte"),
|
|
+ MIB_DESC(1, 0x6c, "Tx256Byte"),
|
|
+ MIB_DESC(1, 0x70, "Tx512Byte"),
|
|
+ MIB_DESC(1, 0x74, "Tx1024Byte"),
|
|
+ MIB_DESC(1, 0x78, "Tx1518Byte"),
|
|
+ MIB_DESC(1, 0x7c, "TxMaxByte"),
|
|
+ MIB_DESC(1, 0x80, "TxOverSize"),
|
|
+ MIB_DESC(2, 0x84, "TxByte"),
|
|
+ MIB_DESC(1, 0x8c, "TxCollision"),
|
|
+ MIB_DESC(1, 0x90, "TxAbortCol"),
|
|
+ MIB_DESC(1, 0x94, "TxMultiCol"),
|
|
+ MIB_DESC(1, 0x98, "TxSingleCol"),
|
|
+ MIB_DESC(1, 0x9c, "TxExcDefer"),
|
|
+ MIB_DESC(1, 0xa0, "TxDefer"),
|
|
+ MIB_DESC(1, 0xa4, "TxLateCol"),
|
|
+ MIB_DESC(1, 0xa8, "RXUnicast"),
|
|
+ MIB_DESC(1, 0xac, "TXUnicast"),
|
|
+};
|
|
+
|
|
+static void
|
|
+qca8k_split_addr(u32 regaddr, u16 *r1, u16 *r2, u16 *page)
|
|
+{
|
|
+ regaddr >>= 1;
|
|
+ *r1 = regaddr & 0x1e;
|
|
+
|
|
+ regaddr >>= 5;
|
|
+ *r2 = regaddr & 0x7;
|
|
+
|
|
+ regaddr >>= 3;
|
|
+ *page = regaddr & 0x3ff;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_set_lo(struct qca8k_priv *priv, int phy_id, u32 regnum, u16 lo)
|
|
+{
|
|
+ u16 *cached_lo = &priv->mdio_cache.lo;
|
|
+ struct mii_bus *bus = priv->bus;
|
|
+ int ret;
|
|
+
|
|
+ if (lo == *cached_lo)
|
|
+ return 0;
|
|
+
|
|
+ ret = bus->write(bus, phy_id, regnum, lo);
|
|
+ if (ret < 0)
|
|
+ dev_err_ratelimited(&bus->dev,
|
|
+ "failed to write qca8k 32bit lo register\n");
|
|
+
|
|
+ *cached_lo = lo;
|
|
+ return 0;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_set_hi(struct qca8k_priv *priv, int phy_id, u32 regnum, u16 hi)
|
|
+{
|
|
+ u16 *cached_hi = &priv->mdio_cache.hi;
|
|
+ struct mii_bus *bus = priv->bus;
|
|
+ int ret;
|
|
+
|
|
+ if (hi == *cached_hi)
|
|
+ return 0;
|
|
+
|
|
+ ret = bus->write(bus, phy_id, regnum, hi);
|
|
+ if (ret < 0)
|
|
+ dev_err_ratelimited(&bus->dev,
|
|
+ "failed to write qca8k 32bit hi register\n");
|
|
+
|
|
+ *cached_hi = hi;
|
|
+ return 0;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_mii_read32(struct mii_bus *bus, int phy_id, u32 regnum, u32 *val)
|
|
+{
|
|
+ int ret;
|
|
+
|
|
+ ret = bus->read(bus, phy_id, regnum);
|
|
+ if (ret >= 0) {
|
|
+ *val = ret;
|
|
+ ret = bus->read(bus, phy_id, regnum + 1);
|
|
+ *val |= ret << 16;
|
|
+ }
|
|
+
|
|
+ if (ret < 0) {
|
|
+ dev_err_ratelimited(&bus->dev,
|
|
+ "failed to read qca8k 32bit register\n");
|
|
+ *val = 0;
|
|
+ return ret;
|
|
+ }
|
|
+
|
|
+ return 0;
|
|
+}
|
|
+
|
|
+static void
|
|
+qca8k_mii_write32(struct qca8k_priv *priv, int phy_id, u32 regnum, u32 val)
|
|
+{
|
|
+ u16 lo, hi;
|
|
+ int ret;
|
|
+
|
|
+ lo = val & 0xffff;
|
|
+ hi = (u16)(val >> 16);
|
|
+
|
|
+ ret = qca8k_set_lo(priv, phy_id, regnum, lo);
|
|
+ if (ret >= 0)
|
|
+ ret = qca8k_set_hi(priv, phy_id, regnum + 1, hi);
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_set_page(struct qca8k_priv *priv, u16 page)
|
|
+{
|
|
+ u16 *cached_page = &priv->mdio_cache.page;
|
|
+ struct mii_bus *bus = priv->bus;
|
|
+ int ret;
|
|
+
|
|
+ if (page == *cached_page)
|
|
+ return 0;
|
|
+
|
|
+ ret = bus->write(bus, 0x18, 0, page);
|
|
+ if (ret < 0) {
|
|
+ dev_err_ratelimited(&bus->dev,
|
|
+ "failed to set qca8k page\n");
|
|
+ return ret;
|
|
+ }
|
|
+
|
|
+ *cached_page = page;
|
|
+ usleep_range(1000, 2000);
|
|
+ return 0;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_read(struct qca8k_priv *priv, u32 reg, u32 *val)
|
|
+{
|
|
+ return regmap_read(priv->regmap, reg, val);
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_write(struct qca8k_priv *priv, u32 reg, u32 val)
|
|
+{
|
|
+ return regmap_write(priv->regmap, reg, val);
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_rmw(struct qca8k_priv *priv, u32 reg, u32 mask, u32 write_val)
|
|
+{
|
|
+ return regmap_update_bits(priv->regmap, reg, mask, write_val);
|
|
+}
|
|
+
|
|
+static void qca8k_rw_reg_ack_handler(struct dsa_switch *ds, struct sk_buff *skb)
|
|
+{
|
|
+ struct qca8k_mgmt_eth_data *mgmt_eth_data;
|
|
+ struct qca8k_priv *priv = ds->priv;
|
|
+ struct qca_mgmt_ethhdr *mgmt_ethhdr;
|
|
+ u8 len, cmd;
|
|
+
|
|
+ mgmt_ethhdr = (struct qca_mgmt_ethhdr *)skb_mac_header(skb);
|
|
+ mgmt_eth_data = &priv->mgmt_eth_data;
|
|
+
|
|
+ cmd = FIELD_GET(QCA_HDR_MGMT_CMD, mgmt_ethhdr->command);
|
|
+ len = FIELD_GET(QCA_HDR_MGMT_LENGTH, mgmt_ethhdr->command);
|
|
+
|
|
+ /* Make sure the seq match the requested packet */
|
|
+ if (mgmt_ethhdr->seq == mgmt_eth_data->seq)
|
|
+ mgmt_eth_data->ack = true;
|
|
+
|
|
+ if (cmd == MDIO_READ) {
|
|
+ mgmt_eth_data->data[0] = mgmt_ethhdr->mdio_data;
|
|
+
|
|
+ /* Get the rest of the 12 byte of data.
|
|
+ * The read/write function will extract the requested data.
|
|
+ */
|
|
+ if (len > QCA_HDR_MGMT_DATA1_LEN)
|
|
+ memcpy(mgmt_eth_data->data + 1, skb->data,
|
|
+ QCA_HDR_MGMT_DATA2_LEN);
|
|
+ }
|
|
+
|
|
+ complete(&mgmt_eth_data->rw_done);
|
|
+}
|
|
+
|
|
+static struct sk_buff *qca8k_alloc_mdio_header(enum mdio_cmd cmd, u32 reg, u32 *val,
|
|
+ int priority, unsigned int len)
|
|
+{
|
|
+ struct qca_mgmt_ethhdr *mgmt_ethhdr;
|
|
+ unsigned int real_len;
|
|
+ struct sk_buff *skb;
|
|
+ u32 *data2;
|
|
+ u16 hdr;
|
|
+
|
|
+ skb = dev_alloc_skb(QCA_HDR_MGMT_PKT_LEN);
|
|
+ if (!skb)
|
|
+ return NULL;
|
|
+
|
|
+ /* Max value for len reg is 15 (0xf) but the switch actually return 16 byte
|
|
+ * Actually for some reason the steps are:
|
|
+ * 0: nothing
|
|
+ * 1-4: first 4 byte
|
|
+ * 5-6: first 12 byte
|
|
+ * 7-15: all 16 byte
|
|
+ */
|
|
+ if (len == 16)
|
|
+ real_len = 15;
|
|
+ else
|
|
+ real_len = len;
|
|
+
|
|
+ skb_reset_mac_header(skb);
|
|
+ skb_set_network_header(skb, skb->len);
|
|
+
|
|
+ mgmt_ethhdr = skb_push(skb, QCA_HDR_MGMT_HEADER_LEN + QCA_HDR_LEN);
|
|
+
|
|
+ hdr = FIELD_PREP(QCA_HDR_XMIT_VERSION, QCA_HDR_VERSION);
|
|
+ hdr |= FIELD_PREP(QCA_HDR_XMIT_PRIORITY, priority);
|
|
+ hdr |= QCA_HDR_XMIT_FROM_CPU;
|
|
+ hdr |= FIELD_PREP(QCA_HDR_XMIT_DP_BIT, BIT(0));
|
|
+ hdr |= FIELD_PREP(QCA_HDR_XMIT_CONTROL, QCA_HDR_XMIT_TYPE_RW_REG);
|
|
+
|
|
+ mgmt_ethhdr->command = FIELD_PREP(QCA_HDR_MGMT_ADDR, reg);
|
|
+ mgmt_ethhdr->command |= FIELD_PREP(QCA_HDR_MGMT_LENGTH, real_len);
|
|
+ mgmt_ethhdr->command |= FIELD_PREP(QCA_HDR_MGMT_CMD, cmd);
|
|
+ mgmt_ethhdr->command |= FIELD_PREP(QCA_HDR_MGMT_CHECK_CODE,
|
|
+ QCA_HDR_MGMT_CHECK_CODE_VAL);
|
|
+
|
|
+ if (cmd == MDIO_WRITE)
|
|
+ mgmt_ethhdr->mdio_data = *val;
|
|
+
|
|
+ mgmt_ethhdr->hdr = htons(hdr);
|
|
+
|
|
+ data2 = skb_put_zero(skb, QCA_HDR_MGMT_DATA2_LEN + QCA_HDR_MGMT_PADDING_LEN);
|
|
+ if (cmd == MDIO_WRITE && len > QCA_HDR_MGMT_DATA1_LEN)
|
|
+ memcpy(data2, val + 1, len - QCA_HDR_MGMT_DATA1_LEN);
|
|
+
|
|
+ return skb;
|
|
+}
|
|
+
|
|
+static void qca8k_mdio_header_fill_seq_num(struct sk_buff *skb, u32 seq_num)
|
|
+{
|
|
+ struct qca_mgmt_ethhdr *mgmt_ethhdr;
|
|
+
|
|
+ mgmt_ethhdr = (struct qca_mgmt_ethhdr *)skb->data;
|
|
+ mgmt_ethhdr->seq = FIELD_PREP(QCA_HDR_MGMT_SEQ_NUM, seq_num);
|
|
+}
|
|
+
|
|
+static int qca8k_read_eth(struct qca8k_priv *priv, u32 reg, u32 *val, int len)
|
|
+{
|
|
+ struct qca8k_mgmt_eth_data *mgmt_eth_data = &priv->mgmt_eth_data;
|
|
+ struct sk_buff *skb;
|
|
+ bool ack;
|
|
+ int ret;
|
|
+
|
|
+ skb = qca8k_alloc_mdio_header(MDIO_READ, reg, NULL,
|
|
+ QCA8K_ETHERNET_MDIO_PRIORITY, len);
|
|
+ if (!skb)
|
|
+ return -ENOMEM;
|
|
+
|
|
+ mutex_lock(&mgmt_eth_data->mutex);
|
|
+
|
|
+ /* Check mgmt_master if is operational */
|
|
+ if (!priv->mgmt_master) {
|
|
+ kfree_skb(skb);
|
|
+ mutex_unlock(&mgmt_eth_data->mutex);
|
|
+ return -EINVAL;
|
|
+ }
|
|
+
|
|
+ skb->dev = priv->mgmt_master;
|
|
+
|
|
+ reinit_completion(&mgmt_eth_data->rw_done);
|
|
+
|
|
+ /* Increment seq_num and set it in the mdio pkt */
|
|
+ mgmt_eth_data->seq++;
|
|
+ qca8k_mdio_header_fill_seq_num(skb, mgmt_eth_data->seq);
|
|
+ mgmt_eth_data->ack = false;
|
|
+
|
|
+ dev_queue_xmit(skb);
|
|
+
|
|
+ ret = wait_for_completion_timeout(&mgmt_eth_data->rw_done,
|
|
+ msecs_to_jiffies(QCA8K_ETHERNET_TIMEOUT));
|
|
+
|
|
+ *val = mgmt_eth_data->data[0];
|
|
+ if (len > QCA_HDR_MGMT_DATA1_LEN)
|
|
+ memcpy(val + 1, mgmt_eth_data->data + 1, len - QCA_HDR_MGMT_DATA1_LEN);
|
|
+
|
|
+ ack = mgmt_eth_data->ack;
|
|
+
|
|
+ mutex_unlock(&mgmt_eth_data->mutex);
|
|
+
|
|
+ if (ret <= 0)
|
|
+ return -ETIMEDOUT;
|
|
+
|
|
+ if (!ack)
|
|
+ return -EINVAL;
|
|
+
|
|
+ return 0;
|
|
+}
|
|
+
|
|
+static int qca8k_write_eth(struct qca8k_priv *priv, u32 reg, u32 *val, int len)
|
|
+{
|
|
+ struct qca8k_mgmt_eth_data *mgmt_eth_data = &priv->mgmt_eth_data;
|
|
+ struct sk_buff *skb;
|
|
+ bool ack;
|
|
+ int ret;
|
|
+
|
|
+ skb = qca8k_alloc_mdio_header(MDIO_WRITE, reg, val,
|
|
+ QCA8K_ETHERNET_MDIO_PRIORITY, len);
|
|
+ if (!skb)
|
|
+ return -ENOMEM;
|
|
+
|
|
+ mutex_lock(&mgmt_eth_data->mutex);
|
|
+
|
|
+ /* Check mgmt_master if is operational */
|
|
+ if (!priv->mgmt_master) {
|
|
+ kfree_skb(skb);
|
|
+ mutex_unlock(&mgmt_eth_data->mutex);
|
|
+ return -EINVAL;
|
|
+ }
|
|
+
|
|
+ skb->dev = priv->mgmt_master;
|
|
+
|
|
+ reinit_completion(&mgmt_eth_data->rw_done);
|
|
+
|
|
+ /* Increment seq_num and set it in the mdio pkt */
|
|
+ mgmt_eth_data->seq++;
|
|
+ qca8k_mdio_header_fill_seq_num(skb, mgmt_eth_data->seq);
|
|
+ mgmt_eth_data->ack = false;
|
|
+
|
|
+ dev_queue_xmit(skb);
|
|
+
|
|
+ ret = wait_for_completion_timeout(&mgmt_eth_data->rw_done,
|
|
+ msecs_to_jiffies(QCA8K_ETHERNET_TIMEOUT));
|
|
+
|
|
+ ack = mgmt_eth_data->ack;
|
|
+
|
|
+ mutex_unlock(&mgmt_eth_data->mutex);
|
|
+
|
|
+ if (ret <= 0)
|
|
+ return -ETIMEDOUT;
|
|
+
|
|
+ if (!ack)
|
|
+ return -EINVAL;
|
|
+
|
|
+ return 0;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_regmap_update_bits_eth(struct qca8k_priv *priv, u32 reg, u32 mask, u32 write_val)
|
|
+{
|
|
+ u32 val = 0;
|
|
+ int ret;
|
|
+
|
|
+ ret = qca8k_read_eth(priv, reg, &val, sizeof(val));
|
|
+ if (ret)
|
|
+ return ret;
|
|
+
|
|
+ val &= ~mask;
|
|
+ val |= write_val;
|
|
+
|
|
+ return qca8k_write_eth(priv, reg, &val, sizeof(val));
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_bulk_read(struct qca8k_priv *priv, u32 reg, u32 *val, int len)
|
|
+{
|
|
+ int i, count = len / sizeof(u32), ret;
|
|
+
|
|
+ if (priv->mgmt_master && !qca8k_read_eth(priv, reg, val, len))
|
|
+ return 0;
|
|
+
|
|
+ for (i = 0; i < count; i++) {
|
|
+ ret = regmap_read(priv->regmap, reg + (i * 4), val + i);
|
|
+ if (ret < 0)
|
|
+ return ret;
|
|
+ }
|
|
+
|
|
+ return 0;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_bulk_write(struct qca8k_priv *priv, u32 reg, u32 *val, int len)
|
|
+{
|
|
+ int i, count = len / sizeof(u32), ret;
|
|
+ u32 tmp;
|
|
+
|
|
+ if (priv->mgmt_master && !qca8k_write_eth(priv, reg, val, len))
|
|
+ return 0;
|
|
+
|
|
+ for (i = 0; i < count; i++) {
|
|
+ tmp = val[i];
|
|
+
|
|
+ ret = regmap_write(priv->regmap, reg + (i * 4), tmp);
|
|
+ if (ret < 0)
|
|
+ return ret;
|
|
+ }
|
|
+
|
|
+ return 0;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_regmap_read(void *ctx, uint32_t reg, uint32_t *val)
|
|
+{
|
|
+ struct qca8k_priv *priv = (struct qca8k_priv *)ctx;
|
|
+ struct mii_bus *bus = priv->bus;
|
|
+ u16 r1, r2, page;
|
|
+ int ret;
|
|
+
|
|
+ if (!qca8k_read_eth(priv, reg, val, sizeof(*val)))
|
|
+ return 0;
|
|
+
|
|
+ qca8k_split_addr(reg, &r1, &r2, &page);
|
|
+
|
|
+ mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
|
|
+
|
|
+ ret = qca8k_set_page(priv, page);
|
|
+ if (ret < 0)
|
|
+ goto exit;
|
|
+
|
|
+ ret = qca8k_mii_read32(bus, 0x10 | r2, r1, val);
|
|
+
|
|
+exit:
|
|
+ mutex_unlock(&bus->mdio_lock);
|
|
+ return ret;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_regmap_write(void *ctx, uint32_t reg, uint32_t val)
|
|
+{
|
|
+ struct qca8k_priv *priv = (struct qca8k_priv *)ctx;
|
|
+ struct mii_bus *bus = priv->bus;
|
|
+ u16 r1, r2, page;
|
|
+ int ret;
|
|
+
|
|
+ if (!qca8k_write_eth(priv, reg, &val, sizeof(val)))
|
|
+ return 0;
|
|
+
|
|
+ qca8k_split_addr(reg, &r1, &r2, &page);
|
|
+
|
|
+ mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
|
|
+
|
|
+ ret = qca8k_set_page(priv, page);
|
|
+ if (ret < 0)
|
|
+ goto exit;
|
|
+
|
|
+ qca8k_mii_write32(priv, 0x10 | r2, r1, val);
|
|
+
|
|
+exit:
|
|
+ mutex_unlock(&bus->mdio_lock);
|
|
+ return ret;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_regmap_update_bits(void *ctx, uint32_t reg, uint32_t mask, uint32_t write_val)
|
|
+{
|
|
+ struct qca8k_priv *priv = (struct qca8k_priv *)ctx;
|
|
+ struct mii_bus *bus = priv->bus;
|
|
+ u16 r1, r2, page;
|
|
+ u32 val;
|
|
+ int ret;
|
|
+
|
|
+ if (!qca8k_regmap_update_bits_eth(priv, reg, mask, write_val))
|
|
+ return 0;
|
|
+
|
|
+ qca8k_split_addr(reg, &r1, &r2, &page);
|
|
+
|
|
+ mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
|
|
+
|
|
+ ret = qca8k_set_page(priv, page);
|
|
+ if (ret < 0)
|
|
+ goto exit;
|
|
+
|
|
+ ret = qca8k_mii_read32(bus, 0x10 | r2, r1, &val);
|
|
+ if (ret < 0)
|
|
+ goto exit;
|
|
+
|
|
+ val &= ~mask;
|
|
+ val |= write_val;
|
|
+ qca8k_mii_write32(priv, 0x10 | r2, r1, val);
|
|
+
|
|
+exit:
|
|
+ mutex_unlock(&bus->mdio_lock);
|
|
+
|
|
+ return ret;
|
|
+}
|
|
+
|
|
+static const struct regmap_range qca8k_readable_ranges[] = {
|
|
+ regmap_reg_range(0x0000, 0x00e4), /* Global control */
|
|
+ regmap_reg_range(0x0100, 0x0168), /* EEE control */
|
|
+ regmap_reg_range(0x0200, 0x0270), /* Parser control */
|
|
+ regmap_reg_range(0x0400, 0x0454), /* ACL */
|
|
+ regmap_reg_range(0x0600, 0x0718), /* Lookup */
|
|
+ regmap_reg_range(0x0800, 0x0b70), /* QM */
|
|
+ regmap_reg_range(0x0c00, 0x0c80), /* PKT */
|
|
+ regmap_reg_range(0x0e00, 0x0e98), /* L3 */
|
|
+ regmap_reg_range(0x1000, 0x10ac), /* MIB - Port0 */
|
|
+ regmap_reg_range(0x1100, 0x11ac), /* MIB - Port1 */
|
|
+ regmap_reg_range(0x1200, 0x12ac), /* MIB - Port2 */
|
|
+ regmap_reg_range(0x1300, 0x13ac), /* MIB - Port3 */
|
|
+ regmap_reg_range(0x1400, 0x14ac), /* MIB - Port4 */
|
|
+ regmap_reg_range(0x1500, 0x15ac), /* MIB - Port5 */
|
|
+ regmap_reg_range(0x1600, 0x16ac), /* MIB - Port6 */
|
|
+
|
|
+};
|
|
+
|
|
+static const struct regmap_access_table qca8k_readable_table = {
|
|
+ .yes_ranges = qca8k_readable_ranges,
|
|
+ .n_yes_ranges = ARRAY_SIZE(qca8k_readable_ranges),
|
|
+};
|
|
+
|
|
+static struct regmap_config qca8k_regmap_config = {
|
|
+ .reg_bits = 16,
|
|
+ .val_bits = 32,
|
|
+ .reg_stride = 4,
|
|
+ .max_register = 0x16ac, /* end MIB - Port6 range */
|
|
+ .reg_read = qca8k_regmap_read,
|
|
+ .reg_write = qca8k_regmap_write,
|
|
+ .reg_update_bits = qca8k_regmap_update_bits,
|
|
+ .rd_table = &qca8k_readable_table,
|
|
+ .disable_locking = true, /* Locking is handled by qca8k read/write */
|
|
+ .cache_type = REGCACHE_NONE, /* Explicitly disable CACHE */
|
|
+};
|
|
+
|
|
+static int
|
|
+qca8k_busy_wait(struct qca8k_priv *priv, u32 reg, u32 mask)
|
|
+{
|
|
+ u32 val;
|
|
+
|
|
+ return regmap_read_poll_timeout(priv->regmap, reg, val, !(val & mask), 0,
|
|
+ QCA8K_BUSY_WAIT_TIMEOUT * USEC_PER_MSEC);
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_fdb_read(struct qca8k_priv *priv, struct qca8k_fdb *fdb)
|
|
+{
|
|
+ u32 reg[3];
|
|
+ int ret;
|
|
+
|
|
+ /* load the ARL table into an array */
|
|
+ ret = qca8k_bulk_read(priv, QCA8K_REG_ATU_DATA0, reg, sizeof(reg));
|
|
+ if (ret)
|
|
+ return ret;
|
|
+
|
|
+ /* vid - 83:72 */
|
|
+ fdb->vid = FIELD_GET(QCA8K_ATU_VID_MASK, reg[2]);
|
|
+ /* aging - 67:64 */
|
|
+ fdb->aging = FIELD_GET(QCA8K_ATU_STATUS_MASK, reg[2]);
|
|
+ /* portmask - 54:48 */
|
|
+ fdb->port_mask = FIELD_GET(QCA8K_ATU_PORT_MASK, reg[1]);
|
|
+ /* mac - 47:0 */
|
|
+ fdb->mac[0] = FIELD_GET(QCA8K_ATU_ADDR0_MASK, reg[1]);
|
|
+ fdb->mac[1] = FIELD_GET(QCA8K_ATU_ADDR1_MASK, reg[1]);
|
|
+ fdb->mac[2] = FIELD_GET(QCA8K_ATU_ADDR2_MASK, reg[0]);
|
|
+ fdb->mac[3] = FIELD_GET(QCA8K_ATU_ADDR3_MASK, reg[0]);
|
|
+ fdb->mac[4] = FIELD_GET(QCA8K_ATU_ADDR4_MASK, reg[0]);
|
|
+ fdb->mac[5] = FIELD_GET(QCA8K_ATU_ADDR5_MASK, reg[0]);
|
|
+
|
|
+ return 0;
|
|
+}
|
|
+
|
|
+static void
|
|
+qca8k_fdb_write(struct qca8k_priv *priv, u16 vid, u8 port_mask, const u8 *mac,
|
|
+ u8 aging)
|
|
+{
|
|
+ u32 reg[3] = { 0 };
|
|
+
|
|
+ /* vid - 83:72 */
|
|
+ reg[2] = FIELD_PREP(QCA8K_ATU_VID_MASK, vid);
|
|
+ /* aging - 67:64 */
|
|
+ reg[2] |= FIELD_PREP(QCA8K_ATU_STATUS_MASK, aging);
|
|
+ /* portmask - 54:48 */
|
|
+ reg[1] = FIELD_PREP(QCA8K_ATU_PORT_MASK, port_mask);
|
|
+ /* mac - 47:0 */
|
|
+ reg[1] |= FIELD_PREP(QCA8K_ATU_ADDR0_MASK, mac[0]);
|
|
+ reg[1] |= FIELD_PREP(QCA8K_ATU_ADDR1_MASK, mac[1]);
|
|
+ reg[0] |= FIELD_PREP(QCA8K_ATU_ADDR2_MASK, mac[2]);
|
|
+ reg[0] |= FIELD_PREP(QCA8K_ATU_ADDR3_MASK, mac[3]);
|
|
+ reg[0] |= FIELD_PREP(QCA8K_ATU_ADDR4_MASK, mac[4]);
|
|
+ reg[0] |= FIELD_PREP(QCA8K_ATU_ADDR5_MASK, mac[5]);
|
|
+
|
|
+ /* load the array into the ARL table */
|
|
+ qca8k_bulk_write(priv, QCA8K_REG_ATU_DATA0, reg, sizeof(reg));
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_fdb_access(struct qca8k_priv *priv, enum qca8k_fdb_cmd cmd, int port)
|
|
+{
|
|
+ u32 reg;
|
|
+ int ret;
|
|
+
|
|
+ /* Set the command and FDB index */
|
|
+ reg = QCA8K_ATU_FUNC_BUSY;
|
|
+ reg |= cmd;
|
|
+ if (port >= 0) {
|
|
+ reg |= QCA8K_ATU_FUNC_PORT_EN;
|
|
+ reg |= FIELD_PREP(QCA8K_ATU_FUNC_PORT_MASK, port);
|
|
+ }
|
|
+
|
|
+ /* Write the function register triggering the table access */
|
|
+ ret = qca8k_write(priv, QCA8K_REG_ATU_FUNC, reg);
|
|
+ if (ret)
|
|
+ return ret;
|
|
+
|
|
+ /* wait for completion */
|
|
+ ret = qca8k_busy_wait(priv, QCA8K_REG_ATU_FUNC, QCA8K_ATU_FUNC_BUSY);
|
|
+ if (ret)
|
|
+ return ret;
|
|
+
|
|
+ /* Check for table full violation when adding an entry */
|
|
+ if (cmd == QCA8K_FDB_LOAD) {
|
|
+ ret = qca8k_read(priv, QCA8K_REG_ATU_FUNC, ®);
|
|
+ if (ret < 0)
|
|
+ return ret;
|
|
+ if (reg & QCA8K_ATU_FUNC_FULL)
|
|
+ return -1;
|
|
+ }
|
|
+
|
|
+ return 0;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_fdb_next(struct qca8k_priv *priv, struct qca8k_fdb *fdb, int port)
|
|
+{
|
|
+ int ret;
|
|
+
|
|
+ qca8k_fdb_write(priv, fdb->vid, fdb->port_mask, fdb->mac, fdb->aging);
|
|
+ ret = qca8k_fdb_access(priv, QCA8K_FDB_NEXT, port);
|
|
+ if (ret < 0)
|
|
+ return ret;
|
|
+
|
|
+ return qca8k_fdb_read(priv, fdb);
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_fdb_add(struct qca8k_priv *priv, const u8 *mac, u16 port_mask,
|
|
+ u16 vid, u8 aging)
|
|
+{
|
|
+ int ret;
|
|
+
|
|
+ mutex_lock(&priv->reg_mutex);
|
|
+ qca8k_fdb_write(priv, vid, port_mask, mac, aging);
|
|
+ ret = qca8k_fdb_access(priv, QCA8K_FDB_LOAD, -1);
|
|
+ mutex_unlock(&priv->reg_mutex);
|
|
+
|
|
+ return ret;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_fdb_del(struct qca8k_priv *priv, const u8 *mac, u16 port_mask, u16 vid)
|
|
+{
|
|
+ int ret;
|
|
+
|
|
+ mutex_lock(&priv->reg_mutex);
|
|
+ qca8k_fdb_write(priv, vid, port_mask, mac, 0);
|
|
+ ret = qca8k_fdb_access(priv, QCA8K_FDB_PURGE, -1);
|
|
+ mutex_unlock(&priv->reg_mutex);
|
|
+
|
|
+ return ret;
|
|
+}
|
|
+
|
|
+static void
|
|
+qca8k_fdb_flush(struct qca8k_priv *priv)
|
|
+{
|
|
+ mutex_lock(&priv->reg_mutex);
|
|
+ qca8k_fdb_access(priv, QCA8K_FDB_FLUSH, -1);
|
|
+ mutex_unlock(&priv->reg_mutex);
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_fdb_search_and_insert(struct qca8k_priv *priv, u8 port_mask,
|
|
+ const u8 *mac, u16 vid)
|
|
+{
|
|
+ struct qca8k_fdb fdb = { 0 };
|
|
+ int ret;
|
|
+
|
|
+ mutex_lock(&priv->reg_mutex);
|
|
+
|
|
+ qca8k_fdb_write(priv, vid, 0, mac, 0);
|
|
+ ret = qca8k_fdb_access(priv, QCA8K_FDB_SEARCH, -1);
|
|
+ if (ret < 0)
|
|
+ goto exit;
|
|
+
|
|
+ ret = qca8k_fdb_read(priv, &fdb);
|
|
+ if (ret < 0)
|
|
+ goto exit;
|
|
+
|
|
+ /* Rule exist. Delete first */
|
|
+ if (!fdb.aging) {
|
|
+ ret = qca8k_fdb_access(priv, QCA8K_FDB_PURGE, -1);
|
|
+ if (ret)
|
|
+ goto exit;
|
|
+ }
|
|
+
|
|
+ /* Add port to fdb portmask */
|
|
+ fdb.port_mask |= port_mask;
|
|
+
|
|
+ qca8k_fdb_write(priv, vid, fdb.port_mask, mac, fdb.aging);
|
|
+ ret = qca8k_fdb_access(priv, QCA8K_FDB_LOAD, -1);
|
|
+
|
|
+exit:
|
|
+ mutex_unlock(&priv->reg_mutex);
|
|
+ return ret;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_fdb_search_and_del(struct qca8k_priv *priv, u8 port_mask,
|
|
+ const u8 *mac, u16 vid)
|
|
+{
|
|
+ struct qca8k_fdb fdb = { 0 };
|
|
+ int ret;
|
|
+
|
|
+ mutex_lock(&priv->reg_mutex);
|
|
+
|
|
+ qca8k_fdb_write(priv, vid, 0, mac, 0);
|
|
+ ret = qca8k_fdb_access(priv, QCA8K_FDB_SEARCH, -1);
|
|
+ if (ret < 0)
|
|
+ goto exit;
|
|
+
|
|
+ /* Rule doesn't exist. Why delete? */
|
|
+ if (!fdb.aging) {
|
|
+ ret = -EINVAL;
|
|
+ goto exit;
|
|
+ }
|
|
+
|
|
+ ret = qca8k_fdb_access(priv, QCA8K_FDB_PURGE, -1);
|
|
+ if (ret)
|
|
+ goto exit;
|
|
+
|
|
+ /* Only port in the rule is this port. Don't re insert */
|
|
+ if (fdb.port_mask == port_mask)
|
|
+ goto exit;
|
|
+
|
|
+ /* Remove port from port mask */
|
|
+ fdb.port_mask &= ~port_mask;
|
|
+
|
|
+ qca8k_fdb_write(priv, vid, fdb.port_mask, mac, fdb.aging);
|
|
+ ret = qca8k_fdb_access(priv, QCA8K_FDB_LOAD, -1);
|
|
+
|
|
+exit:
|
|
+ mutex_unlock(&priv->reg_mutex);
|
|
+ return ret;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_vlan_access(struct qca8k_priv *priv, enum qca8k_vlan_cmd cmd, u16 vid)
|
|
+{
|
|
+ u32 reg;
|
|
+ int ret;
|
|
+
|
|
+ /* Set the command and VLAN index */
|
|
+ reg = QCA8K_VTU_FUNC1_BUSY;
|
|
+ reg |= cmd;
|
|
+ reg |= FIELD_PREP(QCA8K_VTU_FUNC1_VID_MASK, vid);
|
|
+
|
|
+ /* Write the function register triggering the table access */
|
|
+ ret = qca8k_write(priv, QCA8K_REG_VTU_FUNC1, reg);
|
|
+ if (ret)
|
|
+ return ret;
|
|
+
|
|
+ /* wait for completion */
|
|
+ ret = qca8k_busy_wait(priv, QCA8K_REG_VTU_FUNC1, QCA8K_VTU_FUNC1_BUSY);
|
|
+ if (ret)
|
|
+ return ret;
|
|
+
|
|
+ /* Check for table full violation when adding an entry */
|
|
+ if (cmd == QCA8K_VLAN_LOAD) {
|
|
+ ret = qca8k_read(priv, QCA8K_REG_VTU_FUNC1, ®);
|
|
+ if (ret < 0)
|
|
+ return ret;
|
|
+ if (reg & QCA8K_VTU_FUNC1_FULL)
|
|
+ return -ENOMEM;
|
|
+ }
|
|
+
|
|
+ return 0;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_vlan_add(struct qca8k_priv *priv, u8 port, u16 vid, bool untagged)
|
|
+{
|
|
+ u32 reg;
|
|
+ int ret;
|
|
+
|
|
+ /*
|
|
+ We do the right thing with VLAN 0 and treat it as untagged while
|
|
+ preserving the tag on egress.
|
|
+ */
|
|
+ if (vid == 0)
|
|
+ return 0;
|
|
+
|
|
+ mutex_lock(&priv->reg_mutex);
|
|
+ ret = qca8k_vlan_access(priv, QCA8K_VLAN_READ, vid);
|
|
+ if (ret < 0)
|
|
+ goto out;
|
|
+
|
|
+ ret = qca8k_read(priv, QCA8K_REG_VTU_FUNC0, ®);
|
|
+ if (ret < 0)
|
|
+ goto out;
|
|
+ reg |= QCA8K_VTU_FUNC0_VALID | QCA8K_VTU_FUNC0_IVL_EN;
|
|
+ reg &= ~QCA8K_VTU_FUNC0_EG_MODE_PORT_MASK(port);
|
|
+ if (untagged)
|
|
+ reg |= QCA8K_VTU_FUNC0_EG_MODE_PORT_UNTAG(port);
|
|
+ else
|
|
+ reg |= QCA8K_VTU_FUNC0_EG_MODE_PORT_TAG(port);
|
|
+
|
|
+ ret = qca8k_write(priv, QCA8K_REG_VTU_FUNC0, reg);
|
|
+ if (ret)
|
|
+ goto out;
|
|
+ ret = qca8k_vlan_access(priv, QCA8K_VLAN_LOAD, vid);
|
|
+
|
|
+out:
|
|
+ mutex_unlock(&priv->reg_mutex);
|
|
+
|
|
+ return ret;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_vlan_del(struct qca8k_priv *priv, u8 port, u16 vid)
|
|
+{
|
|
+ u32 reg, mask;
|
|
+ int ret, i;
|
|
+ bool del;
|
|
+
|
|
+ mutex_lock(&priv->reg_mutex);
|
|
+ ret = qca8k_vlan_access(priv, QCA8K_VLAN_READ, vid);
|
|
+ if (ret < 0)
|
|
+ goto out;
|
|
+
|
|
+ ret = qca8k_read(priv, QCA8K_REG_VTU_FUNC0, ®);
|
|
+ if (ret < 0)
|
|
+ goto out;
|
|
+ reg &= ~QCA8K_VTU_FUNC0_EG_MODE_PORT_MASK(port);
|
|
+ reg |= QCA8K_VTU_FUNC0_EG_MODE_PORT_NOT(port);
|
|
+
|
|
+ /* Check if we're the last member to be removed */
|
|
+ del = true;
|
|
+ for (i = 0; i < QCA8K_NUM_PORTS; i++) {
|
|
+ mask = QCA8K_VTU_FUNC0_EG_MODE_PORT_NOT(i);
|
|
+
|
|
+ if ((reg & mask) != mask) {
|
|
+ del = false;
|
|
+ break;
|
|
+ }
|
|
+ }
|
|
+
|
|
+ if (del) {
|
|
+ ret = qca8k_vlan_access(priv, QCA8K_VLAN_PURGE, vid);
|
|
+ } else {
|
|
+ ret = qca8k_write(priv, QCA8K_REG_VTU_FUNC0, reg);
|
|
+ if (ret)
|
|
+ goto out;
|
|
+ ret = qca8k_vlan_access(priv, QCA8K_VLAN_LOAD, vid);
|
|
+ }
|
|
+
|
|
+out:
|
|
+ mutex_unlock(&priv->reg_mutex);
|
|
+
|
|
+ return ret;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_mib_init(struct qca8k_priv *priv)
|
|
+{
|
|
+ int ret;
|
|
+
|
|
+ mutex_lock(&priv->reg_mutex);
|
|
+ ret = regmap_update_bits(priv->regmap, QCA8K_REG_MIB,
|
|
+ QCA8K_MIB_FUNC | QCA8K_MIB_BUSY,
|
|
+ FIELD_PREP(QCA8K_MIB_FUNC, QCA8K_MIB_FLUSH) |
|
|
+ QCA8K_MIB_BUSY);
|
|
+ if (ret)
|
|
+ goto exit;
|
|
+
|
|
+ ret = qca8k_busy_wait(priv, QCA8K_REG_MIB, QCA8K_MIB_BUSY);
|
|
+ if (ret)
|
|
+ goto exit;
|
|
+
|
|
+ ret = regmap_set_bits(priv->regmap, QCA8K_REG_MIB, QCA8K_MIB_CPU_KEEP);
|
|
+ if (ret)
|
|
+ goto exit;
|
|
+
|
|
+ ret = qca8k_write(priv, QCA8K_REG_MODULE_EN, QCA8K_MODULE_EN_MIB);
|
|
+
|
|
+exit:
|
|
+ mutex_unlock(&priv->reg_mutex);
|
|
+ return ret;
|
|
+}
|
|
+
|
|
+static void
|
|
+qca8k_port_set_status(struct qca8k_priv *priv, int port, int enable)
|
|
+{
|
|
+ u32 mask = QCA8K_PORT_STATUS_TXMAC | QCA8K_PORT_STATUS_RXMAC;
|
|
+
|
|
+ /* Port 0 and 6 have no internal PHY */
|
|
+ if (port > 0 && port < 6)
|
|
+ mask |= QCA8K_PORT_STATUS_LINK_AUTO;
|
|
+
|
|
+ if (enable)
|
|
+ regmap_set_bits(priv->regmap, QCA8K_REG_PORT_STATUS(port), mask);
|
|
+ else
|
|
+ regmap_clear_bits(priv->regmap, QCA8K_REG_PORT_STATUS(port), mask);
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_phy_eth_busy_wait(struct qca8k_mgmt_eth_data *mgmt_eth_data,
|
|
+ struct sk_buff *read_skb, u32 *val)
|
|
+{
|
|
+ struct sk_buff *skb = skb_copy(read_skb, GFP_KERNEL);
|
|
+ bool ack;
|
|
+ int ret;
|
|
+
|
|
+ reinit_completion(&mgmt_eth_data->rw_done);
|
|
+
|
|
+ /* Increment seq_num and set it in the copy pkt */
|
|
+ mgmt_eth_data->seq++;
|
|
+ qca8k_mdio_header_fill_seq_num(skb, mgmt_eth_data->seq);
|
|
+ mgmt_eth_data->ack = false;
|
|
+
|
|
+ dev_queue_xmit(skb);
|
|
+
|
|
+ ret = wait_for_completion_timeout(&mgmt_eth_data->rw_done,
|
|
+ QCA8K_ETHERNET_TIMEOUT);
|
|
+
|
|
+ ack = mgmt_eth_data->ack;
|
|
+
|
|
+ if (ret <= 0)
|
|
+ return -ETIMEDOUT;
|
|
+
|
|
+ if (!ack)
|
|
+ return -EINVAL;
|
|
+
|
|
+ *val = mgmt_eth_data->data[0];
|
|
+
|
|
+ return 0;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_phy_eth_command(struct qca8k_priv *priv, bool read, int phy,
|
|
+ int regnum, u16 data)
|
|
+{
|
|
+ struct sk_buff *write_skb, *clear_skb, *read_skb;
|
|
+ struct qca8k_mgmt_eth_data *mgmt_eth_data;
|
|
+ u32 write_val, clear_val = 0, val;
|
|
+ struct net_device *mgmt_master;
|
|
+ int ret, ret1;
|
|
+ bool ack;
|
|
+
|
|
+ if (regnum >= QCA8K_MDIO_MASTER_MAX_REG)
|
|
+ return -EINVAL;
|
|
+
|
|
+ mgmt_eth_data = &priv->mgmt_eth_data;
|
|
+
|
|
+ write_val = QCA8K_MDIO_MASTER_BUSY | QCA8K_MDIO_MASTER_EN |
|
|
+ QCA8K_MDIO_MASTER_PHY_ADDR(phy) |
|
|
+ QCA8K_MDIO_MASTER_REG_ADDR(regnum);
|
|
+
|
|
+ if (read) {
|
|
+ write_val |= QCA8K_MDIO_MASTER_READ;
|
|
+ } else {
|
|
+ write_val |= QCA8K_MDIO_MASTER_WRITE;
|
|
+ write_val |= QCA8K_MDIO_MASTER_DATA(data);
|
|
+ }
|
|
+
|
|
+ /* Prealloc all the needed skb before the lock */
|
|
+ write_skb = qca8k_alloc_mdio_header(MDIO_WRITE, QCA8K_MDIO_MASTER_CTRL, &write_val,
|
|
+ QCA8K_ETHERNET_PHY_PRIORITY, sizeof(write_val));
|
|
+ if (!write_skb)
|
|
+ return -ENOMEM;
|
|
+
|
|
+ clear_skb = qca8k_alloc_mdio_header(MDIO_WRITE, QCA8K_MDIO_MASTER_CTRL, &clear_val,
|
|
+ QCA8K_ETHERNET_PHY_PRIORITY, sizeof(clear_val));
|
|
+ if (!clear_skb) {
|
|
+ ret = -ENOMEM;
|
|
+ goto err_clear_skb;
|
|
+ }
|
|
+
|
|
+ read_skb = qca8k_alloc_mdio_header(MDIO_READ, QCA8K_MDIO_MASTER_CTRL, &clear_val,
|
|
+ QCA8K_ETHERNET_PHY_PRIORITY, sizeof(clear_val));
|
|
+ if (!read_skb) {
|
|
+ ret = -ENOMEM;
|
|
+ goto err_read_skb;
|
|
+ }
|
|
+
|
|
+ /* Actually start the request:
|
|
+ * 1. Send mdio master packet
|
|
+ * 2. Busy Wait for mdio master command
|
|
+ * 3. Get the data if we are reading
|
|
+ * 4. Reset the mdio master (even with error)
|
|
+ */
|
|
+ mutex_lock(&mgmt_eth_data->mutex);
|
|
+
|
|
+ /* Check if mgmt_master is operational */
|
|
+ mgmt_master = priv->mgmt_master;
|
|
+ if (!mgmt_master) {
|
|
+ mutex_unlock(&mgmt_eth_data->mutex);
|
|
+ ret = -EINVAL;
|
|
+ goto err_mgmt_master;
|
|
+ }
|
|
+
|
|
+ read_skb->dev = mgmt_master;
|
|
+ clear_skb->dev = mgmt_master;
|
|
+ write_skb->dev = mgmt_master;
|
|
+
|
|
+ reinit_completion(&mgmt_eth_data->rw_done);
|
|
+
|
|
+ /* Increment seq_num and set it in the write pkt */
|
|
+ mgmt_eth_data->seq++;
|
|
+ qca8k_mdio_header_fill_seq_num(write_skb, mgmt_eth_data->seq);
|
|
+ mgmt_eth_data->ack = false;
|
|
+
|
|
+ dev_queue_xmit(write_skb);
|
|
+
|
|
+ ret = wait_for_completion_timeout(&mgmt_eth_data->rw_done,
|
|
+ QCA8K_ETHERNET_TIMEOUT);
|
|
+
|
|
+ ack = mgmt_eth_data->ack;
|
|
+
|
|
+ if (ret <= 0) {
|
|
+ ret = -ETIMEDOUT;
|
|
+ kfree_skb(read_skb);
|
|
+ goto exit;
|
|
+ }
|
|
+
|
|
+ if (!ack) {
|
|
+ ret = -EINVAL;
|
|
+ kfree_skb(read_skb);
|
|
+ goto exit;
|
|
+ }
|
|
+
|
|
+ ret = read_poll_timeout(qca8k_phy_eth_busy_wait, ret1,
|
|
+ !(val & QCA8K_MDIO_MASTER_BUSY), 0,
|
|
+ QCA8K_BUSY_WAIT_TIMEOUT * USEC_PER_MSEC, false,
|
|
+ mgmt_eth_data, read_skb, &val);
|
|
+
|
|
+ if (ret < 0 && ret1 < 0) {
|
|
+ ret = ret1;
|
|
+ goto exit;
|
|
+ }
|
|
+
|
|
+ if (read) {
|
|
+ reinit_completion(&mgmt_eth_data->rw_done);
|
|
+
|
|
+ /* Increment seq_num and set it in the read pkt */
|
|
+ mgmt_eth_data->seq++;
|
|
+ qca8k_mdio_header_fill_seq_num(read_skb, mgmt_eth_data->seq);
|
|
+ mgmt_eth_data->ack = false;
|
|
+
|
|
+ dev_queue_xmit(read_skb);
|
|
+
|
|
+ ret = wait_for_completion_timeout(&mgmt_eth_data->rw_done,
|
|
+ QCA8K_ETHERNET_TIMEOUT);
|
|
+
|
|
+ ack = mgmt_eth_data->ack;
|
|
+
|
|
+ if (ret <= 0) {
|
|
+ ret = -ETIMEDOUT;
|
|
+ goto exit;
|
|
+ }
|
|
+
|
|
+ if (!ack) {
|
|
+ ret = -EINVAL;
|
|
+ goto exit;
|
|
+ }
|
|
+
|
|
+ ret = mgmt_eth_data->data[0] & QCA8K_MDIO_MASTER_DATA_MASK;
|
|
+ } else {
|
|
+ kfree_skb(read_skb);
|
|
+ }
|
|
+exit:
|
|
+ reinit_completion(&mgmt_eth_data->rw_done);
|
|
+
|
|
+ /* Increment seq_num and set it in the clear pkt */
|
|
+ mgmt_eth_data->seq++;
|
|
+ qca8k_mdio_header_fill_seq_num(clear_skb, mgmt_eth_data->seq);
|
|
+ mgmt_eth_data->ack = false;
|
|
+
|
|
+ dev_queue_xmit(clear_skb);
|
|
+
|
|
+ wait_for_completion_timeout(&mgmt_eth_data->rw_done,
|
|
+ QCA8K_ETHERNET_TIMEOUT);
|
|
+
|
|
+ mutex_unlock(&mgmt_eth_data->mutex);
|
|
+
|
|
+ return ret;
|
|
+
|
|
+ /* Error handling before lock */
|
|
+err_mgmt_master:
|
|
+ kfree_skb(read_skb);
|
|
+err_read_skb:
|
|
+ kfree_skb(clear_skb);
|
|
+err_clear_skb:
|
|
+ kfree_skb(write_skb);
|
|
+
|
|
+ return ret;
|
|
+}
|
|
+
|
|
+static u32
|
|
+qca8k_port_to_phy(int port)
|
|
+{
|
|
+ /* From Andrew Lunn:
|
|
+ * Port 0 has no internal phy.
|
|
+ * Port 1 has an internal PHY at MDIO address 0.
|
|
+ * Port 2 has an internal PHY at MDIO address 1.
|
|
+ * ...
|
|
+ * Port 5 has an internal PHY at MDIO address 4.
|
|
+ * Port 6 has no internal PHY.
|
|
+ */
|
|
+
|
|
+ return port - 1;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_mdio_busy_wait(struct mii_bus *bus, u32 reg, u32 mask)
|
|
+{
|
|
+ u16 r1, r2, page;
|
|
+ u32 val;
|
|
+ int ret, ret1;
|
|
+
|
|
+ qca8k_split_addr(reg, &r1, &r2, &page);
|
|
+
|
|
+ ret = read_poll_timeout(qca8k_mii_read32, ret1, !(val & mask), 0,
|
|
+ QCA8K_BUSY_WAIT_TIMEOUT * USEC_PER_MSEC, false,
|
|
+ bus, 0x10 | r2, r1, &val);
|
|
+
|
|
+ /* Check if qca8k_read has failed for a different reason
|
|
+ * before returnting -ETIMEDOUT
|
|
+ */
|
|
+ if (ret < 0 && ret1 < 0)
|
|
+ return ret1;
|
|
+
|
|
+ return ret;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_mdio_write(struct qca8k_priv *priv, int phy, int regnum, u16 data)
|
|
+{
|
|
+ struct mii_bus *bus = priv->bus;
|
|
+ u16 r1, r2, page;
|
|
+ u32 val;
|
|
+ int ret;
|
|
+
|
|
+ if (regnum >= QCA8K_MDIO_MASTER_MAX_REG)
|
|
+ return -EINVAL;
|
|
+
|
|
+ val = QCA8K_MDIO_MASTER_BUSY | QCA8K_MDIO_MASTER_EN |
|
|
+ QCA8K_MDIO_MASTER_WRITE | QCA8K_MDIO_MASTER_PHY_ADDR(phy) |
|
|
+ QCA8K_MDIO_MASTER_REG_ADDR(regnum) |
|
|
+ QCA8K_MDIO_MASTER_DATA(data);
|
|
+
|
|
+ qca8k_split_addr(QCA8K_MDIO_MASTER_CTRL, &r1, &r2, &page);
|
|
+
|
|
+ mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
|
|
+
|
|
+ ret = qca8k_set_page(priv, page);
|
|
+ if (ret)
|
|
+ goto exit;
|
|
+
|
|
+ qca8k_mii_write32(priv, 0x10 | r2, r1, val);
|
|
+
|
|
+ ret = qca8k_mdio_busy_wait(bus, QCA8K_MDIO_MASTER_CTRL,
|
|
+ QCA8K_MDIO_MASTER_BUSY);
|
|
+
|
|
+exit:
|
|
+ /* even if the busy_wait timeouts try to clear the MASTER_EN */
|
|
+ qca8k_mii_write32(priv, 0x10 | r2, r1, 0);
|
|
+
|
|
+ mutex_unlock(&bus->mdio_lock);
|
|
+
|
|
+ return ret;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_mdio_read(struct qca8k_priv *priv, int phy, int regnum)
|
|
+{
|
|
+ struct mii_bus *bus = priv->bus;
|
|
+ u16 r1, r2, page;
|
|
+ u32 val;
|
|
+ int ret;
|
|
+
|
|
+ if (regnum >= QCA8K_MDIO_MASTER_MAX_REG)
|
|
+ return -EINVAL;
|
|
+
|
|
+ val = QCA8K_MDIO_MASTER_BUSY | QCA8K_MDIO_MASTER_EN |
|
|
+ QCA8K_MDIO_MASTER_READ | QCA8K_MDIO_MASTER_PHY_ADDR(phy) |
|
|
+ QCA8K_MDIO_MASTER_REG_ADDR(regnum);
|
|
+
|
|
+ qca8k_split_addr(QCA8K_MDIO_MASTER_CTRL, &r1, &r2, &page);
|
|
+
|
|
+ mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
|
|
+
|
|
+ ret = qca8k_set_page(priv, page);
|
|
+ if (ret)
|
|
+ goto exit;
|
|
+
|
|
+ qca8k_mii_write32(priv, 0x10 | r2, r1, val);
|
|
+
|
|
+ ret = qca8k_mdio_busy_wait(bus, QCA8K_MDIO_MASTER_CTRL,
|
|
+ QCA8K_MDIO_MASTER_BUSY);
|
|
+ if (ret)
|
|
+ goto exit;
|
|
+
|
|
+ ret = qca8k_mii_read32(bus, 0x10 | r2, r1, &val);
|
|
+
|
|
+exit:
|
|
+ /* even if the busy_wait timeouts try to clear the MASTER_EN */
|
|
+ qca8k_mii_write32(priv, 0x10 | r2, r1, 0);
|
|
+
|
|
+ mutex_unlock(&bus->mdio_lock);
|
|
+
|
|
+ if (ret >= 0)
|
|
+ ret = val & QCA8K_MDIO_MASTER_DATA_MASK;
|
|
+
|
|
+ return ret;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_internal_mdio_write(struct mii_bus *slave_bus, int phy, int regnum, u16 data)
|
|
+{
|
|
+ struct qca8k_priv *priv = slave_bus->priv;
|
|
+ int ret;
|
|
+
|
|
+ /* Use mdio Ethernet when available, fallback to legacy one on error */
|
|
+ ret = qca8k_phy_eth_command(priv, false, phy, regnum, data);
|
|
+ if (!ret)
|
|
+ return 0;
|
|
+
|
|
+ return qca8k_mdio_write(priv, phy, regnum, data);
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_internal_mdio_read(struct mii_bus *slave_bus, int phy, int regnum)
|
|
+{
|
|
+ struct qca8k_priv *priv = slave_bus->priv;
|
|
+ int ret;
|
|
+
|
|
+ /* Use mdio Ethernet when available, fallback to legacy one on error */
|
|
+ ret = qca8k_phy_eth_command(priv, true, phy, regnum, 0);
|
|
+ if (ret >= 0)
|
|
+ return ret;
|
|
+
|
|
+ ret = qca8k_mdio_read(priv, phy, regnum);
|
|
+
|
|
+ if (ret < 0)
|
|
+ return 0xffff;
|
|
+
|
|
+ return ret;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_legacy_mdio_write(struct mii_bus *slave_bus, int port, int regnum, u16 data)
|
|
+{
|
|
+ port = qca8k_port_to_phy(port) % PHY_MAX_ADDR;
|
|
+
|
|
+ return qca8k_internal_mdio_write(slave_bus, port, regnum, data);
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_legacy_mdio_read(struct mii_bus *slave_bus, int port, int regnum)
|
|
+{
|
|
+ port = qca8k_port_to_phy(port) % PHY_MAX_ADDR;
|
|
+
|
|
+ return qca8k_internal_mdio_read(slave_bus, port, regnum);
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_mdio_register(struct qca8k_priv *priv)
|
|
+{
|
|
+ struct dsa_switch *ds = priv->ds;
|
|
+ struct device_node *mdio;
|
|
+ struct mii_bus *bus;
|
|
+
|
|
+ bus = devm_mdiobus_alloc(ds->dev);
|
|
+ if (!bus)
|
|
+ return -ENOMEM;
|
|
+
|
|
+ bus->priv = (void *)priv;
|
|
+ snprintf(bus->id, MII_BUS_ID_SIZE, "qca8k-%d.%d",
|
|
+ ds->dst->index, ds->index);
|
|
+ bus->parent = ds->dev;
|
|
+ bus->phy_mask = ~ds->phys_mii_mask;
|
|
+ ds->slave_mii_bus = bus;
|
|
+
|
|
+ /* Check if the devicetree declare the port:phy mapping */
|
|
+ mdio = of_get_child_by_name(priv->dev->of_node, "mdio");
|
|
+ if (of_device_is_available(mdio)) {
|
|
+ bus->name = "qca8k slave mii";
|
|
+ bus->read = qca8k_internal_mdio_read;
|
|
+ bus->write = qca8k_internal_mdio_write;
|
|
+ return devm_of_mdiobus_register(priv->dev, bus, mdio);
|
|
+ }
|
|
+
|
|
+ /* If a mapping can't be found the legacy mapping is used,
|
|
+ * using the qca8k_port_to_phy function
|
|
+ */
|
|
+ bus->name = "qca8k-legacy slave mii";
|
|
+ bus->read = qca8k_legacy_mdio_read;
|
|
+ bus->write = qca8k_legacy_mdio_write;
|
|
+ return devm_mdiobus_register(priv->dev, bus);
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_setup_mdio_bus(struct qca8k_priv *priv)
|
|
+{
|
|
+ u32 internal_mdio_mask = 0, external_mdio_mask = 0, reg;
|
|
+ struct device_node *ports, *port;
|
|
+ phy_interface_t mode;
|
|
+ int err;
|
|
+
|
|
+ ports = of_get_child_by_name(priv->dev->of_node, "ports");
|
|
+ if (!ports)
|
|
+ ports = of_get_child_by_name(priv->dev->of_node, "ethernet-ports");
|
|
+
|
|
+ if (!ports)
|
|
+ return -EINVAL;
|
|
+
|
|
+ for_each_available_child_of_node(ports, port) {
|
|
+ err = of_property_read_u32(port, "reg", ®);
|
|
+ if (err) {
|
|
+ of_node_put(port);
|
|
+ of_node_put(ports);
|
|
+ return err;
|
|
+ }
|
|
+
|
|
+ if (!dsa_is_user_port(priv->ds, reg))
|
|
+ continue;
|
|
+
|
|
+ of_get_phy_mode(port, &mode);
|
|
+
|
|
+ if (of_property_read_bool(port, "phy-handle") &&
|
|
+ mode != PHY_INTERFACE_MODE_INTERNAL)
|
|
+ external_mdio_mask |= BIT(reg);
|
|
+ else
|
|
+ internal_mdio_mask |= BIT(reg);
|
|
+ }
|
|
+
|
|
+ of_node_put(ports);
|
|
+ if (!external_mdio_mask && !internal_mdio_mask) {
|
|
+ dev_err(priv->dev, "no PHYs are defined.\n");
|
|
+ return -EINVAL;
|
|
+ }
|
|
+
|
|
+ /* The QCA8K_MDIO_MASTER_EN Bit, which grants access to PHYs through
|
|
+ * the MDIO_MASTER register also _disconnects_ the external MDC
|
|
+ * passthrough to the internal PHYs. It's not possible to use both
|
|
+ * configurations at the same time!
|
|
+ *
|
|
+ * Because this came up during the review process:
|
|
+ * If the external mdio-bus driver is capable magically disabling
|
|
+ * the QCA8K_MDIO_MASTER_EN and mutex/spin-locking out the qca8k's
|
|
+ * accessors for the time being, it would be possible to pull this
|
|
+ * off.
|
|
+ */
|
|
+ if (!!external_mdio_mask && !!internal_mdio_mask) {
|
|
+ dev_err(priv->dev, "either internal or external mdio bus configuration is supported.\n");
|
|
+ return -EINVAL;
|
|
+ }
|
|
+
|
|
+ if (external_mdio_mask) {
|
|
+ /* Make sure to disable the internal mdio bus in cases
|
|
+ * a dt-overlay and driver reload changed the configuration
|
|
+ */
|
|
+
|
|
+ return regmap_clear_bits(priv->regmap, QCA8K_MDIO_MASTER_CTRL,
|
|
+ QCA8K_MDIO_MASTER_EN);
|
|
+ }
|
|
+
|
|
+ return qca8k_mdio_register(priv);
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_setup_mac_pwr_sel(struct qca8k_priv *priv)
|
|
+{
|
|
+ u32 mask = 0;
|
|
+ int ret = 0;
|
|
+
|
|
+ /* SoC specific settings for ipq8064.
|
|
+ * If more device require this consider adding
|
|
+ * a dedicated binding.
|
|
+ */
|
|
+ if (of_machine_is_compatible("qcom,ipq8064"))
|
|
+ mask |= QCA8K_MAC_PWR_RGMII0_1_8V;
|
|
+
|
|
+ /* SoC specific settings for ipq8065 */
|
|
+ if (of_machine_is_compatible("qcom,ipq8065"))
|
|
+ mask |= QCA8K_MAC_PWR_RGMII1_1_8V;
|
|
+
|
|
+ if (mask) {
|
|
+ ret = qca8k_rmw(priv, QCA8K_REG_MAC_PWR_SEL,
|
|
+ QCA8K_MAC_PWR_RGMII0_1_8V |
|
|
+ QCA8K_MAC_PWR_RGMII1_1_8V,
|
|
+ mask);
|
|
+ }
|
|
+
|
|
+ return ret;
|
|
+}
|
|
+
|
|
+static int qca8k_find_cpu_port(struct dsa_switch *ds)
|
|
+{
|
|
+ struct qca8k_priv *priv = ds->priv;
|
|
+
|
|
+ /* Find the connected cpu port. Valid port are 0 or 6 */
|
|
+ if (dsa_is_cpu_port(ds, 0))
|
|
+ return 0;
|
|
+
|
|
+ dev_dbg(priv->dev, "port 0 is not the CPU port. Checking port 6");
|
|
+
|
|
+ if (dsa_is_cpu_port(ds, 6))
|
|
+ return 6;
|
|
+
|
|
+ return -EINVAL;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_setup_of_pws_reg(struct qca8k_priv *priv)
|
|
+{
|
|
+ struct device_node *node = priv->dev->of_node;
|
|
+ const struct qca8k_match_data *data;
|
|
+ u32 val = 0;
|
|
+ int ret;
|
|
+
|
|
+ /* QCA8327 require to set to the correct mode.
|
|
+ * His bigger brother QCA8328 have the 172 pin layout.
|
|
+ * Should be applied by default but we set this just to make sure.
|
|
+ */
|
|
+ if (priv->switch_id == QCA8K_ID_QCA8327) {
|
|
+ data = of_device_get_match_data(priv->dev);
|
|
+
|
|
+ /* Set the correct package of 148 pin for QCA8327 */
|
|
+ if (data->reduced_package)
|
|
+ val |= QCA8327_PWS_PACKAGE148_EN;
|
|
+
|
|
+ ret = qca8k_rmw(priv, QCA8K_REG_PWS, QCA8327_PWS_PACKAGE148_EN,
|
|
+ val);
|
|
+ if (ret)
|
|
+ return ret;
|
|
+ }
|
|
+
|
|
+ if (of_property_read_bool(node, "qca,ignore-power-on-sel"))
|
|
+ val |= QCA8K_PWS_POWER_ON_SEL;
|
|
+
|
|
+ if (of_property_read_bool(node, "qca,led-open-drain")) {
|
|
+ if (!(val & QCA8K_PWS_POWER_ON_SEL)) {
|
|
+ dev_err(priv->dev, "qca,led-open-drain require qca,ignore-power-on-sel to be set.");
|
|
+ return -EINVAL;
|
|
+ }
|
|
+
|
|
+ val |= QCA8K_PWS_LED_OPEN_EN_CSR;
|
|
+ }
|
|
+
|
|
+ return qca8k_rmw(priv, QCA8K_REG_PWS,
|
|
+ QCA8K_PWS_LED_OPEN_EN_CSR | QCA8K_PWS_POWER_ON_SEL,
|
|
+ val);
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_parse_port_config(struct qca8k_priv *priv)
|
|
+{
|
|
+ int port, cpu_port_index = -1, ret;
|
|
+ struct device_node *port_dn;
|
|
+ phy_interface_t mode;
|
|
+ struct dsa_port *dp;
|
|
+ u32 delay;
|
|
+
|
|
+ /* We have 2 CPU port. Check them */
|
|
+ for (port = 0; port < QCA8K_NUM_PORTS; port++) {
|
|
+ /* Skip every other port */
|
|
+ if (port != 0 && port != 6)
|
|
+ continue;
|
|
+
|
|
+ dp = dsa_to_port(priv->ds, port);
|
|
+ port_dn = dp->dn;
|
|
+ cpu_port_index++;
|
|
+
|
|
+ if (!of_device_is_available(port_dn))
|
|
+ continue;
|
|
+
|
|
+ ret = of_get_phy_mode(port_dn, &mode);
|
|
+ if (ret)
|
|
+ continue;
|
|
+
|
|
+ switch (mode) {
|
|
+ case PHY_INTERFACE_MODE_RGMII:
|
|
+ case PHY_INTERFACE_MODE_RGMII_ID:
|
|
+ case PHY_INTERFACE_MODE_RGMII_TXID:
|
|
+ case PHY_INTERFACE_MODE_RGMII_RXID:
|
|
+ case PHY_INTERFACE_MODE_SGMII:
|
|
+ delay = 0;
|
|
+
|
|
+ if (!of_property_read_u32(port_dn, "tx-internal-delay-ps", &delay))
|
|
+ /* Switch regs accept value in ns, convert ps to ns */
|
|
+ delay = delay / 1000;
|
|
+ else if (mode == PHY_INTERFACE_MODE_RGMII_ID ||
|
|
+ mode == PHY_INTERFACE_MODE_RGMII_TXID)
|
|
+ delay = 1;
|
|
+
|
|
+ if (!FIELD_FIT(QCA8K_PORT_PAD_RGMII_TX_DELAY_MASK, delay)) {
|
|
+ dev_err(priv->dev, "rgmii tx delay is limited to a max value of 3ns, setting to the max value");
|
|
+ delay = 3;
|
|
+ }
|
|
+
|
|
+ priv->ports_config.rgmii_tx_delay[cpu_port_index] = delay;
|
|
+
|
|
+ delay = 0;
|
|
+
|
|
+ if (!of_property_read_u32(port_dn, "rx-internal-delay-ps", &delay))
|
|
+ /* Switch regs accept value in ns, convert ps to ns */
|
|
+ delay = delay / 1000;
|
|
+ else if (mode == PHY_INTERFACE_MODE_RGMII_ID ||
|
|
+ mode == PHY_INTERFACE_MODE_RGMII_RXID)
|
|
+ delay = 2;
|
|
+
|
|
+ if (!FIELD_FIT(QCA8K_PORT_PAD_RGMII_RX_DELAY_MASK, delay)) {
|
|
+ dev_err(priv->dev, "rgmii rx delay is limited to a max value of 3ns, setting to the max value");
|
|
+ delay = 3;
|
|
+ }
|
|
+
|
|
+ priv->ports_config.rgmii_rx_delay[cpu_port_index] = delay;
|
|
+
|
|
+ /* Skip sgmii parsing for rgmii* mode */
|
|
+ if (mode == PHY_INTERFACE_MODE_RGMII ||
|
|
+ mode == PHY_INTERFACE_MODE_RGMII_ID ||
|
|
+ mode == PHY_INTERFACE_MODE_RGMII_TXID ||
|
|
+ mode == PHY_INTERFACE_MODE_RGMII_RXID)
|
|
+ break;
|
|
+
|
|
+ if (of_property_read_bool(port_dn, "qca,sgmii-txclk-falling-edge"))
|
|
+ priv->ports_config.sgmii_tx_clk_falling_edge = true;
|
|
+
|
|
+ if (of_property_read_bool(port_dn, "qca,sgmii-rxclk-falling-edge"))
|
|
+ priv->ports_config.sgmii_rx_clk_falling_edge = true;
|
|
+
|
|
+ if (of_property_read_bool(port_dn, "qca,sgmii-enable-pll")) {
|
|
+ priv->ports_config.sgmii_enable_pll = true;
|
|
+
|
|
+ if (priv->switch_id == QCA8K_ID_QCA8327) {
|
|
+ dev_err(priv->dev, "SGMII PLL should NOT be enabled for qca8327. Aborting enabling");
|
|
+ priv->ports_config.sgmii_enable_pll = false;
|
|
+ }
|
|
+
|
|
+ if (priv->switch_revision < 2)
|
|
+ dev_warn(priv->dev, "SGMII PLL should NOT be enabled for qca8337 with revision 2 or more.");
|
|
+ }
|
|
+
|
|
+ break;
|
|
+ default:
|
|
+ continue;
|
|
+ }
|
|
+ }
|
|
+
|
|
+ return 0;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_setup(struct dsa_switch *ds)
|
|
+{
|
|
+ struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
|
|
+ int cpu_port, ret, i;
|
|
+ u32 mask;
|
|
+
|
|
+ cpu_port = qca8k_find_cpu_port(ds);
|
|
+ if (cpu_port < 0) {
|
|
+ dev_err(priv->dev, "No cpu port configured in both cpu port0 and port6");
|
|
+ return cpu_port;
|
|
+ }
|
|
+
|
|
+ /* Parse CPU port config to be later used in phy_link mac_config */
|
|
+ ret = qca8k_parse_port_config(priv);
|
|
+ if (ret)
|
|
+ return ret;
|
|
+
|
|
+ ret = qca8k_setup_mdio_bus(priv);
|
|
+ if (ret)
|
|
+ return ret;
|
|
+
|
|
+ ret = qca8k_setup_of_pws_reg(priv);
|
|
+ if (ret)
|
|
+ return ret;
|
|
+
|
|
+ ret = qca8k_setup_mac_pwr_sel(priv);
|
|
+ if (ret)
|
|
+ return ret;
|
|
+
|
|
+ /* Make sure MAC06 is disabled */
|
|
+ ret = regmap_clear_bits(priv->regmap, QCA8K_REG_PORT0_PAD_CTRL,
|
|
+ QCA8K_PORT0_PAD_MAC06_EXCHANGE_EN);
|
|
+ if (ret) {
|
|
+ dev_err(priv->dev, "failed disabling MAC06 exchange");
|
|
+ return ret;
|
|
+ }
|
|
+
|
|
+ /* Enable CPU Port */
|
|
+ ret = regmap_set_bits(priv->regmap, QCA8K_REG_GLOBAL_FW_CTRL0,
|
|
+ QCA8K_GLOBAL_FW_CTRL0_CPU_PORT_EN);
|
|
+ if (ret) {
|
|
+ dev_err(priv->dev, "failed enabling CPU port");
|
|
+ return ret;
|
|
+ }
|
|
+
|
|
+ /* Enable MIB counters */
|
|
+ ret = qca8k_mib_init(priv);
|
|
+ if (ret)
|
|
+ dev_warn(priv->dev, "mib init failed");
|
|
+
|
|
+ /* Initial setup of all ports */
|
|
+ for (i = 0; i < QCA8K_NUM_PORTS; i++) {
|
|
+ /* Disable forwarding by default on all ports */
|
|
+ ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i),
|
|
+ QCA8K_PORT_LOOKUP_MEMBER, 0);
|
|
+ if (ret)
|
|
+ return ret;
|
|
+
|
|
+ /* Enable QCA header mode on all cpu ports */
|
|
+ if (dsa_is_cpu_port(ds, i)) {
|
|
+ ret = qca8k_write(priv, QCA8K_REG_PORT_HDR_CTRL(i),
|
|
+ FIELD_PREP(QCA8K_PORT_HDR_CTRL_TX_MASK, QCA8K_PORT_HDR_CTRL_ALL) |
|
|
+ FIELD_PREP(QCA8K_PORT_HDR_CTRL_RX_MASK, QCA8K_PORT_HDR_CTRL_ALL));
|
|
+ if (ret) {
|
|
+ dev_err(priv->dev, "failed enabling QCA header mode");
|
|
+ return ret;
|
|
+ }
|
|
+ }
|
|
+
|
|
+ /* Disable MAC by default on all user ports */
|
|
+ if (dsa_is_user_port(ds, i))
|
|
+ qca8k_port_set_status(priv, i, 0);
|
|
+ }
|
|
+
|
|
+ /* Forward all unknown frames to CPU port for Linux processing
|
|
+ * Notice that in multi-cpu config only one port should be set
|
|
+ * for igmp, unknown, multicast and broadcast packet
|
|
+ */
|
|
+ ret = qca8k_write(priv, QCA8K_REG_GLOBAL_FW_CTRL1,
|
|
+ FIELD_PREP(QCA8K_GLOBAL_FW_CTRL1_IGMP_DP_MASK, BIT(cpu_port)) |
|
|
+ FIELD_PREP(QCA8K_GLOBAL_FW_CTRL1_BC_DP_MASK, BIT(cpu_port)) |
|
|
+ FIELD_PREP(QCA8K_GLOBAL_FW_CTRL1_MC_DP_MASK, BIT(cpu_port)) |
|
|
+ FIELD_PREP(QCA8K_GLOBAL_FW_CTRL1_UC_DP_MASK, BIT(cpu_port)));
|
|
+ if (ret)
|
|
+ return ret;
|
|
+
|
|
+ /* Setup connection between CPU port & user ports
|
|
+ * Configure specific switch configuration for ports
|
|
+ */
|
|
+ for (i = 0; i < QCA8K_NUM_PORTS; i++) {
|
|
+ /* CPU port gets connected to all user ports of the switch */
|
|
+ if (dsa_is_cpu_port(ds, i)) {
|
|
+ ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i),
|
|
+ QCA8K_PORT_LOOKUP_MEMBER, dsa_user_ports(ds));
|
|
+ if (ret)
|
|
+ return ret;
|
|
+ }
|
|
+
|
|
+ /* Individual user ports get connected to CPU port only */
|
|
+ if (dsa_is_user_port(ds, i)) {
|
|
+ ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i),
|
|
+ QCA8K_PORT_LOOKUP_MEMBER,
|
|
+ BIT(cpu_port));
|
|
+ if (ret)
|
|
+ return ret;
|
|
+
|
|
+ /* Enable ARP Auto-learning by default */
|
|
+ ret = regmap_set_bits(priv->regmap, QCA8K_PORT_LOOKUP_CTRL(i),
|
|
+ QCA8K_PORT_LOOKUP_LEARN);
|
|
+ if (ret)
|
|
+ return ret;
|
|
+
|
|
+ /* For port based vlans to work we need to set the
|
|
+ * default egress vid
|
|
+ */
|
|
+ ret = qca8k_rmw(priv, QCA8K_EGRESS_VLAN(i),
|
|
+ QCA8K_EGREES_VLAN_PORT_MASK(i),
|
|
+ QCA8K_EGREES_VLAN_PORT(i, QCA8K_PORT_VID_DEF));
|
|
+ if (ret)
|
|
+ return ret;
|
|
+
|
|
+ ret = qca8k_write(priv, QCA8K_REG_PORT_VLAN_CTRL0(i),
|
|
+ QCA8K_PORT_VLAN_CVID(QCA8K_PORT_VID_DEF) |
|
|
+ QCA8K_PORT_VLAN_SVID(QCA8K_PORT_VID_DEF));
|
|
+ if (ret)
|
|
+ return ret;
|
|
+ }
|
|
+
|
|
+ /* The port 5 of the qca8337 have some problem in flood condition. The
|
|
+ * original legacy driver had some specific buffer and priority settings
|
|
+ * for the different port suggested by the QCA switch team. Add this
|
|
+ * missing settings to improve switch stability under load condition.
|
|
+ * This problem is limited to qca8337 and other qca8k switch are not affected.
|
|
+ */
|
|
+ if (priv->switch_id == QCA8K_ID_QCA8337) {
|
|
+ switch (i) {
|
|
+ /* The 2 CPU port and port 5 requires some different
|
|
+ * priority than any other ports.
|
|
+ */
|
|
+ case 0:
|
|
+ case 5:
|
|
+ case 6:
|
|
+ mask = QCA8K_PORT_HOL_CTRL0_EG_PRI0(0x3) |
|
|
+ QCA8K_PORT_HOL_CTRL0_EG_PRI1(0x4) |
|
|
+ QCA8K_PORT_HOL_CTRL0_EG_PRI2(0x4) |
|
|
+ QCA8K_PORT_HOL_CTRL0_EG_PRI3(0x4) |
|
|
+ QCA8K_PORT_HOL_CTRL0_EG_PRI4(0x6) |
|
|
+ QCA8K_PORT_HOL_CTRL0_EG_PRI5(0x8) |
|
|
+ QCA8K_PORT_HOL_CTRL0_EG_PORT(0x1e);
|
|
+ break;
|
|
+ default:
|
|
+ mask = QCA8K_PORT_HOL_CTRL0_EG_PRI0(0x3) |
|
|
+ QCA8K_PORT_HOL_CTRL0_EG_PRI1(0x4) |
|
|
+ QCA8K_PORT_HOL_CTRL0_EG_PRI2(0x6) |
|
|
+ QCA8K_PORT_HOL_CTRL0_EG_PRI3(0x8) |
|
|
+ QCA8K_PORT_HOL_CTRL0_EG_PORT(0x19);
|
|
+ }
|
|
+ qca8k_write(priv, QCA8K_REG_PORT_HOL_CTRL0(i), mask);
|
|
+
|
|
+ mask = QCA8K_PORT_HOL_CTRL1_ING(0x6) |
|
|
+ QCA8K_PORT_HOL_CTRL1_EG_PRI_BUF_EN |
|
|
+ QCA8K_PORT_HOL_CTRL1_EG_PORT_BUF_EN |
|
|
+ QCA8K_PORT_HOL_CTRL1_WRED_EN;
|
|
+ qca8k_rmw(priv, QCA8K_REG_PORT_HOL_CTRL1(i),
|
|
+ QCA8K_PORT_HOL_CTRL1_ING_BUF_MASK |
|
|
+ QCA8K_PORT_HOL_CTRL1_EG_PRI_BUF_EN |
|
|
+ QCA8K_PORT_HOL_CTRL1_EG_PORT_BUF_EN |
|
|
+ QCA8K_PORT_HOL_CTRL1_WRED_EN,
|
|
+ mask);
|
|
+ }
|
|
+ }
|
|
+
|
|
+ /* Special GLOBAL_FC_THRESH value are needed for ar8327 switch */
|
|
+ if (priv->switch_id == QCA8K_ID_QCA8327) {
|
|
+ mask = QCA8K_GLOBAL_FC_GOL_XON_THRES(288) |
|
|
+ QCA8K_GLOBAL_FC_GOL_XOFF_THRES(496);
|
|
+ qca8k_rmw(priv, QCA8K_REG_GLOBAL_FC_THRESH,
|
|
+ QCA8K_GLOBAL_FC_GOL_XON_THRES_MASK |
|
|
+ QCA8K_GLOBAL_FC_GOL_XOFF_THRES_MASK,
|
|
+ mask);
|
|
+ }
|
|
+
|
|
+ /* Setup our port MTUs to match power on defaults */
|
|
+ ret = qca8k_write(priv, QCA8K_MAX_FRAME_SIZE, ETH_FRAME_LEN + ETH_FCS_LEN);
|
|
+ if (ret)
|
|
+ dev_warn(priv->dev, "failed setting MTU settings");
|
|
+
|
|
+ /* Flush the FDB table */
|
|
+ qca8k_fdb_flush(priv);
|
|
+
|
|
+ /* We don't have interrupts for link changes, so we need to poll */
|
|
+ ds->pcs_poll = true;
|
|
+
|
|
+ /* Set min a max ageing value supported */
|
|
+ ds->ageing_time_min = 7000;
|
|
+ ds->ageing_time_max = 458745000;
|
|
+
|
|
+ /* Set max number of LAGs supported */
|
|
+ ds->num_lag_ids = QCA8K_NUM_LAGS;
|
|
+
|
|
+ return 0;
|
|
+}
|
|
+
|
|
+static void
|
|
+qca8k_mac_config_setup_internal_delay(struct qca8k_priv *priv, int cpu_port_index,
|
|
+ u32 reg)
|
|
+{
|
|
+ u32 delay, val = 0;
|
|
+ int ret;
|
|
+
|
|
+ /* Delay can be declared in 3 different way.
|
|
+ * Mode to rgmii and internal-delay standard binding defined
|
|
+ * rgmii-id or rgmii-tx/rx phy mode set.
|
|
+ * The parse logic set a delay different than 0 only when one
|
|
+ * of the 3 different way is used. In all other case delay is
|
|
+ * not enabled. With ID or TX/RXID delay is enabled and set
|
|
+ * to the default and recommended value.
|
|
+ */
|
|
+ if (priv->ports_config.rgmii_tx_delay[cpu_port_index]) {
|
|
+ delay = priv->ports_config.rgmii_tx_delay[cpu_port_index];
|
|
+
|
|
+ val |= QCA8K_PORT_PAD_RGMII_TX_DELAY(delay) |
|
|
+ QCA8K_PORT_PAD_RGMII_TX_DELAY_EN;
|
|
+ }
|
|
+
|
|
+ if (priv->ports_config.rgmii_rx_delay[cpu_port_index]) {
|
|
+ delay = priv->ports_config.rgmii_rx_delay[cpu_port_index];
|
|
+
|
|
+ val |= QCA8K_PORT_PAD_RGMII_RX_DELAY(delay) |
|
|
+ QCA8K_PORT_PAD_RGMII_RX_DELAY_EN;
|
|
+ }
|
|
+
|
|
+ /* Set RGMII delay based on the selected values */
|
|
+ ret = qca8k_rmw(priv, reg,
|
|
+ QCA8K_PORT_PAD_RGMII_TX_DELAY_MASK |
|
|
+ QCA8K_PORT_PAD_RGMII_RX_DELAY_MASK |
|
|
+ QCA8K_PORT_PAD_RGMII_TX_DELAY_EN |
|
|
+ QCA8K_PORT_PAD_RGMII_RX_DELAY_EN,
|
|
+ val);
|
|
+ if (ret)
|
|
+ dev_err(priv->dev, "Failed to set internal delay for CPU port%d",
|
|
+ cpu_port_index == QCA8K_CPU_PORT0 ? 0 : 6);
|
|
+}
|
|
+
|
|
+static void
|
|
+qca8k_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
|
|
+ const struct phylink_link_state *state)
|
|
+{
|
|
+ struct qca8k_priv *priv = ds->priv;
|
|
+ int cpu_port_index, ret;
|
|
+ u32 reg, val;
|
|
+
|
|
+ switch (port) {
|
|
+ case 0: /* 1st CPU port */
|
|
+ if (state->interface != PHY_INTERFACE_MODE_RGMII &&
|
|
+ state->interface != PHY_INTERFACE_MODE_RGMII_ID &&
|
|
+ state->interface != PHY_INTERFACE_MODE_RGMII_TXID &&
|
|
+ state->interface != PHY_INTERFACE_MODE_RGMII_RXID &&
|
|
+ state->interface != PHY_INTERFACE_MODE_SGMII)
|
|
+ return;
|
|
+
|
|
+ reg = QCA8K_REG_PORT0_PAD_CTRL;
|
|
+ cpu_port_index = QCA8K_CPU_PORT0;
|
|
+ break;
|
|
+ case 1:
|
|
+ case 2:
|
|
+ case 3:
|
|
+ case 4:
|
|
+ case 5:
|
|
+ /* Internal PHY, nothing to do */
|
|
+ return;
|
|
+ case 6: /* 2nd CPU port / external PHY */
|
|
+ if (state->interface != PHY_INTERFACE_MODE_RGMII &&
|
|
+ state->interface != PHY_INTERFACE_MODE_RGMII_ID &&
|
|
+ state->interface != PHY_INTERFACE_MODE_RGMII_TXID &&
|
|
+ state->interface != PHY_INTERFACE_MODE_RGMII_RXID &&
|
|
+ state->interface != PHY_INTERFACE_MODE_SGMII &&
|
|
+ state->interface != PHY_INTERFACE_MODE_1000BASEX)
|
|
+ return;
|
|
+
|
|
+ reg = QCA8K_REG_PORT6_PAD_CTRL;
|
|
+ cpu_port_index = QCA8K_CPU_PORT6;
|
|
+ break;
|
|
+ default:
|
|
+ dev_err(ds->dev, "%s: unsupported port: %i\n", __func__, port);
|
|
+ return;
|
|
+ }
|
|
+
|
|
+ if (port != 6 && phylink_autoneg_inband(mode)) {
|
|
+ dev_err(ds->dev, "%s: in-band negotiation unsupported\n",
|
|
+ __func__);
|
|
+ return;
|
|
+ }
|
|
+
|
|
+ switch (state->interface) {
|
|
+ case PHY_INTERFACE_MODE_RGMII:
|
|
+ case PHY_INTERFACE_MODE_RGMII_ID:
|
|
+ case PHY_INTERFACE_MODE_RGMII_TXID:
|
|
+ case PHY_INTERFACE_MODE_RGMII_RXID:
|
|
+ qca8k_write(priv, reg, QCA8K_PORT_PAD_RGMII_EN);
|
|
+
|
|
+ /* Configure rgmii delay */
|
|
+ qca8k_mac_config_setup_internal_delay(priv, cpu_port_index, reg);
|
|
+
|
|
+ /* QCA8337 requires to set rgmii rx delay for all ports.
|
|
+ * This is enabled through PORT5_PAD_CTRL for all ports,
|
|
+ * rather than individual port registers.
|
|
+ */
|
|
+ if (priv->switch_id == QCA8K_ID_QCA8337)
|
|
+ qca8k_write(priv, QCA8K_REG_PORT5_PAD_CTRL,
|
|
+ QCA8K_PORT_PAD_RGMII_RX_DELAY_EN);
|
|
+ break;
|
|
+ case PHY_INTERFACE_MODE_SGMII:
|
|
+ case PHY_INTERFACE_MODE_1000BASEX:
|
|
+ /* Enable SGMII on the port */
|
|
+ qca8k_write(priv, reg, QCA8K_PORT_PAD_SGMII_EN);
|
|
+
|
|
+ /* Enable/disable SerDes auto-negotiation as necessary */
|
|
+ ret = qca8k_read(priv, QCA8K_REG_PWS, &val);
|
|
+ if (ret)
|
|
+ return;
|
|
+ if (phylink_autoneg_inband(mode))
|
|
+ val &= ~QCA8K_PWS_SERDES_AEN_DIS;
|
|
+ else
|
|
+ val |= QCA8K_PWS_SERDES_AEN_DIS;
|
|
+ qca8k_write(priv, QCA8K_REG_PWS, val);
|
|
+
|
|
+ /* Configure the SGMII parameters */
|
|
+ ret = qca8k_read(priv, QCA8K_REG_SGMII_CTRL, &val);
|
|
+ if (ret)
|
|
+ return;
|
|
+
|
|
+ val |= QCA8K_SGMII_EN_SD;
|
|
+
|
|
+ if (priv->ports_config.sgmii_enable_pll)
|
|
+ val |= QCA8K_SGMII_EN_PLL | QCA8K_SGMII_EN_RX |
|
|
+ QCA8K_SGMII_EN_TX;
|
|
+
|
|
+ if (dsa_is_cpu_port(ds, port)) {
|
|
+ /* CPU port, we're talking to the CPU MAC, be a PHY */
|
|
+ val &= ~QCA8K_SGMII_MODE_CTRL_MASK;
|
|
+ val |= QCA8K_SGMII_MODE_CTRL_PHY;
|
|
+ } else if (state->interface == PHY_INTERFACE_MODE_SGMII) {
|
|
+ val &= ~QCA8K_SGMII_MODE_CTRL_MASK;
|
|
+ val |= QCA8K_SGMII_MODE_CTRL_MAC;
|
|
+ } else if (state->interface == PHY_INTERFACE_MODE_1000BASEX) {
|
|
+ val &= ~QCA8K_SGMII_MODE_CTRL_MASK;
|
|
+ val |= QCA8K_SGMII_MODE_CTRL_BASEX;
|
|
+ }
|
|
+
|
|
+ qca8k_write(priv, QCA8K_REG_SGMII_CTRL, val);
|
|
+
|
|
+ /* From original code is reported port instability as SGMII also
|
|
+ * require delay set. Apply advised values here or take them from DT.
|
|
+ */
|
|
+ if (state->interface == PHY_INTERFACE_MODE_SGMII)
|
|
+ qca8k_mac_config_setup_internal_delay(priv, cpu_port_index, reg);
|
|
+
|
|
+ /* For qca8327/qca8328/qca8334/qca8338 sgmii is unique and
|
|
+ * falling edge is set writing in the PORT0 PAD reg
|
|
+ */
|
|
+ if (priv->switch_id == QCA8K_ID_QCA8327 ||
|
|
+ priv->switch_id == QCA8K_ID_QCA8337)
|
|
+ reg = QCA8K_REG_PORT0_PAD_CTRL;
|
|
+
|
|
+ val = 0;
|
|
+
|
|
+ /* SGMII Clock phase configuration */
|
|
+ if (priv->ports_config.sgmii_rx_clk_falling_edge)
|
|
+ val |= QCA8K_PORT0_PAD_SGMII_RXCLK_FALLING_EDGE;
|
|
+
|
|
+ if (priv->ports_config.sgmii_tx_clk_falling_edge)
|
|
+ val |= QCA8K_PORT0_PAD_SGMII_TXCLK_FALLING_EDGE;
|
|
+
|
|
+ if (val)
|
|
+ ret = qca8k_rmw(priv, reg,
|
|
+ QCA8K_PORT0_PAD_SGMII_RXCLK_FALLING_EDGE |
|
|
+ QCA8K_PORT0_PAD_SGMII_TXCLK_FALLING_EDGE,
|
|
+ val);
|
|
+
|
|
+ break;
|
|
+ default:
|
|
+ dev_err(ds->dev, "xMII mode %s not supported for port %d\n",
|
|
+ phy_modes(state->interface), port);
|
|
+ return;
|
|
+ }
|
|
+}
|
|
+
|
|
+static void
|
|
+qca8k_phylink_validate(struct dsa_switch *ds, int port,
|
|
+ unsigned long *supported,
|
|
+ struct phylink_link_state *state)
|
|
+{
|
|
+ __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
|
|
+
|
|
+ switch (port) {
|
|
+ case 0: /* 1st CPU port */
|
|
+ if (state->interface != PHY_INTERFACE_MODE_NA &&
|
|
+ state->interface != PHY_INTERFACE_MODE_RGMII &&
|
|
+ state->interface != PHY_INTERFACE_MODE_RGMII_ID &&
|
|
+ state->interface != PHY_INTERFACE_MODE_RGMII_TXID &&
|
|
+ state->interface != PHY_INTERFACE_MODE_RGMII_RXID &&
|
|
+ state->interface != PHY_INTERFACE_MODE_SGMII)
|
|
+ goto unsupported;
|
|
+ break;
|
|
+ case 1:
|
|
+ case 2:
|
|
+ case 3:
|
|
+ case 4:
|
|
+ case 5:
|
|
+ /* Internal PHY */
|
|
+ if (state->interface != PHY_INTERFACE_MODE_NA &&
|
|
+ state->interface != PHY_INTERFACE_MODE_GMII &&
|
|
+ state->interface != PHY_INTERFACE_MODE_INTERNAL)
|
|
+ goto unsupported;
|
|
+ break;
|
|
+ case 6: /* 2nd CPU port / external PHY */
|
|
+ if (state->interface != PHY_INTERFACE_MODE_NA &&
|
|
+ state->interface != PHY_INTERFACE_MODE_RGMII &&
|
|
+ state->interface != PHY_INTERFACE_MODE_RGMII_ID &&
|
|
+ state->interface != PHY_INTERFACE_MODE_RGMII_TXID &&
|
|
+ state->interface != PHY_INTERFACE_MODE_RGMII_RXID &&
|
|
+ state->interface != PHY_INTERFACE_MODE_SGMII &&
|
|
+ state->interface != PHY_INTERFACE_MODE_1000BASEX)
|
|
+ goto unsupported;
|
|
+ break;
|
|
+ default:
|
|
+unsupported:
|
|
+ linkmode_zero(supported);
|
|
+ return;
|
|
+ }
|
|
+
|
|
+ phylink_set_port_modes(mask);
|
|
+ phylink_set(mask, Autoneg);
|
|
+
|
|
+ phylink_set(mask, 1000baseT_Full);
|
|
+ phylink_set(mask, 10baseT_Half);
|
|
+ phylink_set(mask, 10baseT_Full);
|
|
+ phylink_set(mask, 100baseT_Half);
|
|
+ phylink_set(mask, 100baseT_Full);
|
|
+
|
|
+ if (state->interface == PHY_INTERFACE_MODE_1000BASEX)
|
|
+ phylink_set(mask, 1000baseX_Full);
|
|
+
|
|
+ phylink_set(mask, Pause);
|
|
+ phylink_set(mask, Asym_Pause);
|
|
+
|
|
+ linkmode_and(supported, supported, mask);
|
|
+ linkmode_and(state->advertising, state->advertising, mask);
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_phylink_mac_link_state(struct dsa_switch *ds, int port,
|
|
+ struct phylink_link_state *state)
|
|
+{
|
|
+ struct qca8k_priv *priv = ds->priv;
|
|
+ u32 reg;
|
|
+ int ret;
|
|
+
|
|
+ ret = qca8k_read(priv, QCA8K_REG_PORT_STATUS(port), ®);
|
|
+ if (ret < 0)
|
|
+ return ret;
|
|
+
|
|
+ state->link = !!(reg & QCA8K_PORT_STATUS_LINK_UP);
|
|
+ state->an_complete = state->link;
|
|
+ state->an_enabled = !!(reg & QCA8K_PORT_STATUS_LINK_AUTO);
|
|
+ state->duplex = (reg & QCA8K_PORT_STATUS_DUPLEX) ? DUPLEX_FULL :
|
|
+ DUPLEX_HALF;
|
|
+
|
|
+ switch (reg & QCA8K_PORT_STATUS_SPEED) {
|
|
+ case QCA8K_PORT_STATUS_SPEED_10:
|
|
+ state->speed = SPEED_10;
|
|
+ break;
|
|
+ case QCA8K_PORT_STATUS_SPEED_100:
|
|
+ state->speed = SPEED_100;
|
|
+ break;
|
|
+ case QCA8K_PORT_STATUS_SPEED_1000:
|
|
+ state->speed = SPEED_1000;
|
|
+ break;
|
|
+ default:
|
|
+ state->speed = SPEED_UNKNOWN;
|
|
+ break;
|
|
+ }
|
|
+
|
|
+ state->pause = MLO_PAUSE_NONE;
|
|
+ if (reg & QCA8K_PORT_STATUS_RXFLOW)
|
|
+ state->pause |= MLO_PAUSE_RX;
|
|
+ if (reg & QCA8K_PORT_STATUS_TXFLOW)
|
|
+ state->pause |= MLO_PAUSE_TX;
|
|
+
|
|
+ return 1;
|
|
+}
|
|
+
|
|
+static void
|
|
+qca8k_phylink_mac_link_down(struct dsa_switch *ds, int port, unsigned int mode,
|
|
+ phy_interface_t interface)
|
|
+{
|
|
+ struct qca8k_priv *priv = ds->priv;
|
|
+
|
|
+ qca8k_port_set_status(priv, port, 0);
|
|
+}
|
|
+
|
|
+static void
|
|
+qca8k_phylink_mac_link_up(struct dsa_switch *ds, int port, unsigned int mode,
|
|
+ phy_interface_t interface, struct phy_device *phydev,
|
|
+ int speed, int duplex, bool tx_pause, bool rx_pause)
|
|
+{
|
|
+ struct qca8k_priv *priv = ds->priv;
|
|
+ u32 reg;
|
|
+
|
|
+ if (phylink_autoneg_inband(mode)) {
|
|
+ reg = QCA8K_PORT_STATUS_LINK_AUTO;
|
|
+ } else {
|
|
+ switch (speed) {
|
|
+ case SPEED_10:
|
|
+ reg = QCA8K_PORT_STATUS_SPEED_10;
|
|
+ break;
|
|
+ case SPEED_100:
|
|
+ reg = QCA8K_PORT_STATUS_SPEED_100;
|
|
+ break;
|
|
+ case SPEED_1000:
|
|
+ reg = QCA8K_PORT_STATUS_SPEED_1000;
|
|
+ break;
|
|
+ default:
|
|
+ reg = QCA8K_PORT_STATUS_LINK_AUTO;
|
|
+ break;
|
|
+ }
|
|
+
|
|
+ if (duplex == DUPLEX_FULL)
|
|
+ reg |= QCA8K_PORT_STATUS_DUPLEX;
|
|
+
|
|
+ if (rx_pause || dsa_is_cpu_port(ds, port))
|
|
+ reg |= QCA8K_PORT_STATUS_RXFLOW;
|
|
+
|
|
+ if (tx_pause || dsa_is_cpu_port(ds, port))
|
|
+ reg |= QCA8K_PORT_STATUS_TXFLOW;
|
|
+ }
|
|
+
|
|
+ reg |= QCA8K_PORT_STATUS_TXMAC | QCA8K_PORT_STATUS_RXMAC;
|
|
+
|
|
+ qca8k_write(priv, QCA8K_REG_PORT_STATUS(port), reg);
|
|
+}
|
|
+
|
|
+static void
|
|
+qca8k_get_strings(struct dsa_switch *ds, int port, u32 stringset, uint8_t *data)
|
|
+{
|
|
+ const struct qca8k_match_data *match_data;
|
|
+ struct qca8k_priv *priv = ds->priv;
|
|
+ int i;
|
|
+
|
|
+ if (stringset != ETH_SS_STATS)
|
|
+ return;
|
|
+
|
|
+ match_data = of_device_get_match_data(priv->dev);
|
|
+
|
|
+ for (i = 0; i < match_data->mib_count; i++)
|
|
+ strncpy(data + i * ETH_GSTRING_LEN, ar8327_mib[i].name,
|
|
+ ETH_GSTRING_LEN);
|
|
+}
|
|
+
|
|
+static void qca8k_mib_autocast_handler(struct dsa_switch *ds, struct sk_buff *skb)
|
|
+{
|
|
+ const struct qca8k_match_data *match_data;
|
|
+ struct qca8k_mib_eth_data *mib_eth_data;
|
|
+ struct qca8k_priv *priv = ds->priv;
|
|
+ const struct qca8k_mib_desc *mib;
|
|
+ struct mib_ethhdr *mib_ethhdr;
|
|
+ int i, mib_len, offset = 0;
|
|
+ u64 *data;
|
|
+ u8 port;
|
|
+
|
|
+ mib_ethhdr = (struct mib_ethhdr *)skb_mac_header(skb);
|
|
+ mib_eth_data = &priv->mib_eth_data;
|
|
+
|
|
+ /* The switch autocast every port. Ignore other packet and
|
|
+ * parse only the requested one.
|
|
+ */
|
|
+ port = FIELD_GET(QCA_HDR_RECV_SOURCE_PORT, ntohs(mib_ethhdr->hdr));
|
|
+ if (port != mib_eth_data->req_port)
|
|
+ goto exit;
|
|
+
|
|
+ match_data = device_get_match_data(priv->dev);
|
|
+ data = mib_eth_data->data;
|
|
+
|
|
+ for (i = 0; i < match_data->mib_count; i++) {
|
|
+ mib = &ar8327_mib[i];
|
|
+
|
|
+ /* First 3 mib are present in the skb head */
|
|
+ if (i < 3) {
|
|
+ data[i] = mib_ethhdr->data[i];
|
|
+ continue;
|
|
+ }
|
|
+
|
|
+ mib_len = sizeof(uint32_t);
|
|
+
|
|
+ /* Some mib are 64 bit wide */
|
|
+ if (mib->size == 2)
|
|
+ mib_len = sizeof(uint64_t);
|
|
+
|
|
+ /* Copy the mib value from packet to the */
|
|
+ memcpy(data + i, skb->data + offset, mib_len);
|
|
+
|
|
+ /* Set the offset for the next mib */
|
|
+ offset += mib_len;
|
|
+ }
|
|
+
|
|
+exit:
|
|
+ /* Complete on receiving all the mib packet */
|
|
+ if (refcount_dec_and_test(&mib_eth_data->port_parsed))
|
|
+ complete(&mib_eth_data->rw_done);
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_get_ethtool_stats_eth(struct dsa_switch *ds, int port, u64 *data)
|
|
+{
|
|
+ struct dsa_port *dp = dsa_to_port(ds, port);
|
|
+ struct qca8k_mib_eth_data *mib_eth_data;
|
|
+ struct qca8k_priv *priv = ds->priv;
|
|
+ int ret;
|
|
+
|
|
+ mib_eth_data = &priv->mib_eth_data;
|
|
+
|
|
+ mutex_lock(&mib_eth_data->mutex);
|
|
+
|
|
+ reinit_completion(&mib_eth_data->rw_done);
|
|
+
|
|
+ mib_eth_data->req_port = dp->index;
|
|
+ mib_eth_data->data = data;
|
|
+ refcount_set(&mib_eth_data->port_parsed, QCA8K_NUM_PORTS);
|
|
+
|
|
+ mutex_lock(&priv->reg_mutex);
|
|
+
|
|
+ /* Send mib autocast request */
|
|
+ ret = regmap_update_bits(priv->regmap, QCA8K_REG_MIB,
|
|
+ QCA8K_MIB_FUNC | QCA8K_MIB_BUSY,
|
|
+ FIELD_PREP(QCA8K_MIB_FUNC, QCA8K_MIB_CAST) |
|
|
+ QCA8K_MIB_BUSY);
|
|
+
|
|
+ mutex_unlock(&priv->reg_mutex);
|
|
+
|
|
+ if (ret)
|
|
+ goto exit;
|
|
+
|
|
+ ret = wait_for_completion_timeout(&mib_eth_data->rw_done, QCA8K_ETHERNET_TIMEOUT);
|
|
+
|
|
+exit:
|
|
+ mutex_unlock(&mib_eth_data->mutex);
|
|
+
|
|
+ return ret;
|
|
+}
|
|
+
|
|
+static void
|
|
+qca8k_get_ethtool_stats(struct dsa_switch *ds, int port,
|
|
+ uint64_t *data)
|
|
+{
|
|
+ struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
|
|
+ const struct qca8k_match_data *match_data;
|
|
+ const struct qca8k_mib_desc *mib;
|
|
+ u32 reg, i, val;
|
|
+ u32 hi = 0;
|
|
+ int ret;
|
|
+
|
|
+ if (priv->mgmt_master &&
|
|
+ qca8k_get_ethtool_stats_eth(ds, port, data) > 0)
|
|
+ return;
|
|
+
|
|
+ match_data = of_device_get_match_data(priv->dev);
|
|
+
|
|
+ for (i = 0; i < match_data->mib_count; i++) {
|
|
+ mib = &ar8327_mib[i];
|
|
+ reg = QCA8K_PORT_MIB_COUNTER(port) + mib->offset;
|
|
+
|
|
+ ret = qca8k_read(priv, reg, &val);
|
|
+ if (ret < 0)
|
|
+ continue;
|
|
+
|
|
+ if (mib->size == 2) {
|
|
+ ret = qca8k_read(priv, reg + 4, &hi);
|
|
+ if (ret < 0)
|
|
+ continue;
|
|
+ }
|
|
+
|
|
+ data[i] = val;
|
|
+ if (mib->size == 2)
|
|
+ data[i] |= (u64)hi << 32;
|
|
+ }
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_get_sset_count(struct dsa_switch *ds, int port, int sset)
|
|
+{
|
|
+ const struct qca8k_match_data *match_data;
|
|
+ struct qca8k_priv *priv = ds->priv;
|
|
+
|
|
+ if (sset != ETH_SS_STATS)
|
|
+ return 0;
|
|
+
|
|
+ match_data = of_device_get_match_data(priv->dev);
|
|
+
|
|
+ return match_data->mib_count;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_set_mac_eee(struct dsa_switch *ds, int port, struct ethtool_eee *eee)
|
|
+{
|
|
+ struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
|
|
+ u32 lpi_en = QCA8K_REG_EEE_CTRL_LPI_EN(port);
|
|
+ u32 reg;
|
|
+ int ret;
|
|
+
|
|
+ mutex_lock(&priv->reg_mutex);
|
|
+ ret = qca8k_read(priv, QCA8K_REG_EEE_CTRL, ®);
|
|
+ if (ret < 0)
|
|
+ goto exit;
|
|
+
|
|
+ if (eee->eee_enabled)
|
|
+ reg |= lpi_en;
|
|
+ else
|
|
+ reg &= ~lpi_en;
|
|
+ ret = qca8k_write(priv, QCA8K_REG_EEE_CTRL, reg);
|
|
+
|
|
+exit:
|
|
+ mutex_unlock(&priv->reg_mutex);
|
|
+ return ret;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_get_mac_eee(struct dsa_switch *ds, int port, struct ethtool_eee *e)
|
|
+{
|
|
+ /* Nothing to do on the port's MAC */
|
|
+ return 0;
|
|
+}
|
|
+
|
|
+static void
|
|
+qca8k_port_stp_state_set(struct dsa_switch *ds, int port, u8 state)
|
|
+{
|
|
+ struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
|
|
+ u32 stp_state;
|
|
+
|
|
+ switch (state) {
|
|
+ case BR_STATE_DISABLED:
|
|
+ stp_state = QCA8K_PORT_LOOKUP_STATE_DISABLED;
|
|
+ break;
|
|
+ case BR_STATE_BLOCKING:
|
|
+ stp_state = QCA8K_PORT_LOOKUP_STATE_BLOCKING;
|
|
+ break;
|
|
+ case BR_STATE_LISTENING:
|
|
+ stp_state = QCA8K_PORT_LOOKUP_STATE_LISTENING;
|
|
+ break;
|
|
+ case BR_STATE_LEARNING:
|
|
+ stp_state = QCA8K_PORT_LOOKUP_STATE_LEARNING;
|
|
+ break;
|
|
+ case BR_STATE_FORWARDING:
|
|
+ default:
|
|
+ stp_state = QCA8K_PORT_LOOKUP_STATE_FORWARD;
|
|
+ break;
|
|
+ }
|
|
+
|
|
+ qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port),
|
|
+ QCA8K_PORT_LOOKUP_STATE_MASK, stp_state);
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_port_bridge_join(struct dsa_switch *ds, int port, struct net_device *br)
|
|
+{
|
|
+ struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
|
|
+ int port_mask, cpu_port;
|
|
+ int i, ret;
|
|
+
|
|
+ cpu_port = dsa_to_port(ds, port)->cpu_dp->index;
|
|
+ port_mask = BIT(cpu_port);
|
|
+
|
|
+ for (i = 0; i < QCA8K_NUM_PORTS; i++) {
|
|
+ if (dsa_is_cpu_port(ds, i))
|
|
+ continue;
|
|
+ if (dsa_to_port(ds, i)->bridge_dev != br)
|
|
+ continue;
|
|
+ /* Add this port to the portvlan mask of the other ports
|
|
+ * in the bridge
|
|
+ */
|
|
+ ret = regmap_set_bits(priv->regmap,
|
|
+ QCA8K_PORT_LOOKUP_CTRL(i),
|
|
+ BIT(port));
|
|
+ if (ret)
|
|
+ return ret;
|
|
+ if (i != port)
|
|
+ port_mask |= BIT(i);
|
|
+ }
|
|
+
|
|
+ /* Add all other ports to this ports portvlan mask */
|
|
+ ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port),
|
|
+ QCA8K_PORT_LOOKUP_MEMBER, port_mask);
|
|
+
|
|
+ return ret;
|
|
+}
|
|
+
|
|
+static void
|
|
+qca8k_port_bridge_leave(struct dsa_switch *ds, int port, struct net_device *br)
|
|
+{
|
|
+ struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
|
|
+ int cpu_port, i;
|
|
+
|
|
+ cpu_port = dsa_to_port(ds, port)->cpu_dp->index;
|
|
+
|
|
+ for (i = 0; i < QCA8K_NUM_PORTS; i++) {
|
|
+ if (dsa_is_cpu_port(ds, i))
|
|
+ continue;
|
|
+ if (dsa_to_port(ds, i)->bridge_dev != br)
|
|
+ continue;
|
|
+ /* Remove this port to the portvlan mask of the other ports
|
|
+ * in the bridge
|
|
+ */
|
|
+ regmap_clear_bits(priv->regmap,
|
|
+ QCA8K_PORT_LOOKUP_CTRL(i),
|
|
+ BIT(port));
|
|
+ }
|
|
+
|
|
+ /* Set the cpu port to be the only one in the portvlan mask of
|
|
+ * this port
|
|
+ */
|
|
+ qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port),
|
|
+ QCA8K_PORT_LOOKUP_MEMBER, BIT(cpu_port));
|
|
+}
|
|
+
|
|
+static void
|
|
+qca8k_port_fast_age(struct dsa_switch *ds, int port)
|
|
+{
|
|
+ struct qca8k_priv *priv = ds->priv;
|
|
+
|
|
+ mutex_lock(&priv->reg_mutex);
|
|
+ qca8k_fdb_access(priv, QCA8K_FDB_FLUSH_PORT, port);
|
|
+ mutex_unlock(&priv->reg_mutex);
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_set_ageing_time(struct dsa_switch *ds, unsigned int msecs)
|
|
+{
|
|
+ struct qca8k_priv *priv = ds->priv;
|
|
+ unsigned int secs = msecs / 1000;
|
|
+ u32 val;
|
|
+
|
|
+ /* AGE_TIME reg is set in 7s step */
|
|
+ val = secs / 7;
|
|
+
|
|
+ /* Handle case with 0 as val to NOT disable
|
|
+ * learning
|
|
+ */
|
|
+ if (!val)
|
|
+ val = 1;
|
|
+
|
|
+ return regmap_update_bits(priv->regmap, QCA8K_REG_ATU_CTRL, QCA8K_ATU_AGE_TIME_MASK,
|
|
+ QCA8K_ATU_AGE_TIME(val));
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_port_enable(struct dsa_switch *ds, int port,
|
|
+ struct phy_device *phy)
|
|
+{
|
|
+ struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
|
|
+
|
|
+ qca8k_port_set_status(priv, port, 1);
|
|
+ priv->port_enabled_map |= BIT(port);
|
|
+
|
|
+ if (dsa_is_user_port(ds, port))
|
|
+ phy_support_asym_pause(phy);
|
|
+
|
|
+ return 0;
|
|
+}
|
|
+
|
|
+static void
|
|
+qca8k_port_disable(struct dsa_switch *ds, int port)
|
|
+{
|
|
+ struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
|
|
+
|
|
+ qca8k_port_set_status(priv, port, 0);
|
|
+ priv->port_enabled_map &= ~BIT(port);
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_port_change_mtu(struct dsa_switch *ds, int port, int new_mtu)
|
|
+{
|
|
+ struct qca8k_priv *priv = ds->priv;
|
|
+ int ret;
|
|
+
|
|
+ /* We have only have a general MTU setting.
|
|
+ * DSA always set the CPU port's MTU to the largest MTU of the slave
|
|
+ * ports.
|
|
+ * Setting MTU just for the CPU port is sufficient to correctly set a
|
|
+ * value for every port.
|
|
+ */
|
|
+ if (!dsa_is_cpu_port(ds, port))
|
|
+ return 0;
|
|
+
|
|
+ /* To change the MAX_FRAME_SIZE the cpu ports must be off or
|
|
+ * the switch panics.
|
|
+ * Turn off both cpu ports before applying the new value to prevent
|
|
+ * this.
|
|
+ */
|
|
+ if (priv->port_enabled_map & BIT(0))
|
|
+ qca8k_port_set_status(priv, 0, 0);
|
|
+
|
|
+ if (priv->port_enabled_map & BIT(6))
|
|
+ qca8k_port_set_status(priv, 6, 0);
|
|
+
|
|
+ /* Include L2 header / FCS length */
|
|
+ ret = qca8k_write(priv, QCA8K_MAX_FRAME_SIZE, new_mtu + ETH_HLEN + ETH_FCS_LEN);
|
|
+
|
|
+ if (priv->port_enabled_map & BIT(0))
|
|
+ qca8k_port_set_status(priv, 0, 1);
|
|
+
|
|
+ if (priv->port_enabled_map & BIT(6))
|
|
+ qca8k_port_set_status(priv, 6, 1);
|
|
+
|
|
+ return ret;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_port_max_mtu(struct dsa_switch *ds, int port)
|
|
+{
|
|
+ return QCA8K_MAX_MTU;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_port_fdb_insert(struct qca8k_priv *priv, const u8 *addr,
|
|
+ u16 port_mask, u16 vid)
|
|
+{
|
|
+ /* Set the vid to the port vlan id if no vid is set */
|
|
+ if (!vid)
|
|
+ vid = QCA8K_PORT_VID_DEF;
|
|
+
|
|
+ return qca8k_fdb_add(priv, addr, port_mask, vid,
|
|
+ QCA8K_ATU_STATUS_STATIC);
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_port_fdb_add(struct dsa_switch *ds, int port,
|
|
+ const unsigned char *addr, u16 vid)
|
|
+{
|
|
+ struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
|
|
+ u16 port_mask = BIT(port);
|
|
+
|
|
+ return qca8k_port_fdb_insert(priv, addr, port_mask, vid);
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_port_fdb_del(struct dsa_switch *ds, int port,
|
|
+ const unsigned char *addr, u16 vid)
|
|
+{
|
|
+ struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
|
|
+ u16 port_mask = BIT(port);
|
|
+
|
|
+ if (!vid)
|
|
+ vid = QCA8K_PORT_VID_DEF;
|
|
+
|
|
+ return qca8k_fdb_del(priv, addr, port_mask, vid);
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_port_fdb_dump(struct dsa_switch *ds, int port,
|
|
+ dsa_fdb_dump_cb_t *cb, void *data)
|
|
+{
|
|
+ struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
|
|
+ struct qca8k_fdb _fdb = { 0 };
|
|
+ int cnt = QCA8K_NUM_FDB_RECORDS;
|
|
+ bool is_static;
|
|
+ int ret = 0;
|
|
+
|
|
+ mutex_lock(&priv->reg_mutex);
|
|
+ while (cnt-- && !qca8k_fdb_next(priv, &_fdb, port)) {
|
|
+ if (!_fdb.aging)
|
|
+ break;
|
|
+ is_static = (_fdb.aging == QCA8K_ATU_STATUS_STATIC);
|
|
+ ret = cb(_fdb.mac, _fdb.vid, is_static, data);
|
|
+ if (ret)
|
|
+ break;
|
|
+ }
|
|
+ mutex_unlock(&priv->reg_mutex);
|
|
+
|
|
+ return 0;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_port_mdb_add(struct dsa_switch *ds, int port,
|
|
+ const struct switchdev_obj_port_mdb *mdb)
|
|
+{
|
|
+ struct qca8k_priv *priv = ds->priv;
|
|
+ const u8 *addr = mdb->addr;
|
|
+ u16 vid = mdb->vid;
|
|
+
|
|
+ return qca8k_fdb_search_and_insert(priv, BIT(port), addr, vid);
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_port_mdb_del(struct dsa_switch *ds, int port,
|
|
+ const struct switchdev_obj_port_mdb *mdb)
|
|
+{
|
|
+ struct qca8k_priv *priv = ds->priv;
|
|
+ const u8 *addr = mdb->addr;
|
|
+ u16 vid = mdb->vid;
|
|
+
|
|
+ return qca8k_fdb_search_and_del(priv, BIT(port), addr, vid);
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_port_mirror_add(struct dsa_switch *ds, int port,
|
|
+ struct dsa_mall_mirror_tc_entry *mirror,
|
|
+ bool ingress)
|
|
+{
|
|
+ struct qca8k_priv *priv = ds->priv;
|
|
+ int monitor_port, ret;
|
|
+ u32 reg, val;
|
|
+
|
|
+ /* Check for existent entry */
|
|
+ if ((ingress ? priv->mirror_rx : priv->mirror_tx) & BIT(port))
|
|
+ return -EEXIST;
|
|
+
|
|
+ ret = regmap_read(priv->regmap, QCA8K_REG_GLOBAL_FW_CTRL0, &val);
|
|
+ if (ret)
|
|
+ return ret;
|
|
+
|
|
+ /* QCA83xx can have only one port set to mirror mode.
|
|
+ * Check that the correct port is requested and return error otherwise.
|
|
+ * When no mirror port is set, the values is set to 0xF
|
|
+ */
|
|
+ monitor_port = FIELD_GET(QCA8K_GLOBAL_FW_CTRL0_MIRROR_PORT_NUM, val);
|
|
+ if (monitor_port != 0xF && monitor_port != mirror->to_local_port)
|
|
+ return -EEXIST;
|
|
+
|
|
+ /* Set the monitor port */
|
|
+ val = FIELD_PREP(QCA8K_GLOBAL_FW_CTRL0_MIRROR_PORT_NUM,
|
|
+ mirror->to_local_port);
|
|
+ ret = regmap_update_bits(priv->regmap, QCA8K_REG_GLOBAL_FW_CTRL0,
|
|
+ QCA8K_GLOBAL_FW_CTRL0_MIRROR_PORT_NUM, val);
|
|
+ if (ret)
|
|
+ return ret;
|
|
+
|
|
+ if (ingress) {
|
|
+ reg = QCA8K_PORT_LOOKUP_CTRL(port);
|
|
+ val = QCA8K_PORT_LOOKUP_ING_MIRROR_EN;
|
|
+ } else {
|
|
+ reg = QCA8K_REG_PORT_HOL_CTRL1(port);
|
|
+ val = QCA8K_PORT_HOL_CTRL1_EG_MIRROR_EN;
|
|
+ }
|
|
+
|
|
+ ret = regmap_update_bits(priv->regmap, reg, val, val);
|
|
+ if (ret)
|
|
+ return ret;
|
|
+
|
|
+ /* Track mirror port for tx and rx to decide when the
|
|
+ * mirror port has to be disabled.
|
|
+ */
|
|
+ if (ingress)
|
|
+ priv->mirror_rx |= BIT(port);
|
|
+ else
|
|
+ priv->mirror_tx |= BIT(port);
|
|
+
|
|
+ return 0;
|
|
+}
|
|
+
|
|
+static void
|
|
+qca8k_port_mirror_del(struct dsa_switch *ds, int port,
|
|
+ struct dsa_mall_mirror_tc_entry *mirror)
|
|
+{
|
|
+ struct qca8k_priv *priv = ds->priv;
|
|
+ u32 reg, val;
|
|
+ int ret;
|
|
+
|
|
+ if (mirror->ingress) {
|
|
+ reg = QCA8K_PORT_LOOKUP_CTRL(port);
|
|
+ val = QCA8K_PORT_LOOKUP_ING_MIRROR_EN;
|
|
+ } else {
|
|
+ reg = QCA8K_REG_PORT_HOL_CTRL1(port);
|
|
+ val = QCA8K_PORT_HOL_CTRL1_EG_MIRROR_EN;
|
|
+ }
|
|
+
|
|
+ ret = regmap_clear_bits(priv->regmap, reg, val);
|
|
+ if (ret)
|
|
+ goto err;
|
|
+
|
|
+ if (mirror->ingress)
|
|
+ priv->mirror_rx &= ~BIT(port);
|
|
+ else
|
|
+ priv->mirror_tx &= ~BIT(port);
|
|
+
|
|
+ /* No port set to send packet to mirror port. Disable mirror port */
|
|
+ if (!priv->mirror_rx && !priv->mirror_tx) {
|
|
+ val = FIELD_PREP(QCA8K_GLOBAL_FW_CTRL0_MIRROR_PORT_NUM, 0xF);
|
|
+ ret = regmap_update_bits(priv->regmap, QCA8K_REG_GLOBAL_FW_CTRL0,
|
|
+ QCA8K_GLOBAL_FW_CTRL0_MIRROR_PORT_NUM, val);
|
|
+ if (ret)
|
|
+ goto err;
|
|
+ }
|
|
+err:
|
|
+ dev_err(priv->dev, "Failed to del mirror port from %d", port);
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_port_vlan_filtering(struct dsa_switch *ds, int port, bool vlan_filtering,
|
|
+ struct netlink_ext_ack *extack)
|
|
+{
|
|
+ struct qca8k_priv *priv = ds->priv;
|
|
+ int ret;
|
|
+
|
|
+ if (vlan_filtering) {
|
|
+ ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port),
|
|
+ QCA8K_PORT_LOOKUP_VLAN_MODE_MASK,
|
|
+ QCA8K_PORT_LOOKUP_VLAN_MODE_SECURE);
|
|
+ } else {
|
|
+ ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port),
|
|
+ QCA8K_PORT_LOOKUP_VLAN_MODE_MASK,
|
|
+ QCA8K_PORT_LOOKUP_VLAN_MODE_NONE);
|
|
+ }
|
|
+
|
|
+ return ret;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_port_vlan_add(struct dsa_switch *ds, int port,
|
|
+ const struct switchdev_obj_port_vlan *vlan,
|
|
+ struct netlink_ext_ack *extack)
|
|
+{
|
|
+ bool untagged = vlan->flags & BRIDGE_VLAN_INFO_UNTAGGED;
|
|
+ bool pvid = vlan->flags & BRIDGE_VLAN_INFO_PVID;
|
|
+ struct qca8k_priv *priv = ds->priv;
|
|
+ int ret;
|
|
+
|
|
+ ret = qca8k_vlan_add(priv, port, vlan->vid, untagged);
|
|
+ if (ret) {
|
|
+ dev_err(priv->dev, "Failed to add VLAN to port %d (%d)", port, ret);
|
|
+ return ret;
|
|
+ }
|
|
+
|
|
+ if (pvid) {
|
|
+ ret = qca8k_rmw(priv, QCA8K_EGRESS_VLAN(port),
|
|
+ QCA8K_EGREES_VLAN_PORT_MASK(port),
|
|
+ QCA8K_EGREES_VLAN_PORT(port, vlan->vid));
|
|
+ if (ret)
|
|
+ return ret;
|
|
+
|
|
+ ret = qca8k_write(priv, QCA8K_REG_PORT_VLAN_CTRL0(port),
|
|
+ QCA8K_PORT_VLAN_CVID(vlan->vid) |
|
|
+ QCA8K_PORT_VLAN_SVID(vlan->vid));
|
|
+ }
|
|
+
|
|
+ return ret;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_port_vlan_del(struct dsa_switch *ds, int port,
|
|
+ const struct switchdev_obj_port_vlan *vlan)
|
|
+{
|
|
+ struct qca8k_priv *priv = ds->priv;
|
|
+ int ret;
|
|
+
|
|
+ ret = qca8k_vlan_del(priv, port, vlan->vid);
|
|
+ if (ret)
|
|
+ dev_err(priv->dev, "Failed to delete VLAN from port %d (%d)", port, ret);
|
|
+
|
|
+ return ret;
|
|
+}
|
|
+
|
|
+static u32 qca8k_get_phy_flags(struct dsa_switch *ds, int port)
|
|
+{
|
|
+ struct qca8k_priv *priv = ds->priv;
|
|
+
|
|
+ /* Communicate to the phy internal driver the switch revision.
|
|
+ * Based on the switch revision different values needs to be
|
|
+ * set to the dbg and mmd reg on the phy.
|
|
+ * The first 2 bit are used to communicate the switch revision
|
|
+ * to the phy driver.
|
|
+ */
|
|
+ if (port > 0 && port < 6)
|
|
+ return priv->switch_revision;
|
|
+
|
|
+ return 0;
|
|
+}
|
|
+
|
|
+static enum dsa_tag_protocol
|
|
+qca8k_get_tag_protocol(struct dsa_switch *ds, int port,
|
|
+ enum dsa_tag_protocol mp)
|
|
+{
|
|
+ return DSA_TAG_PROTO_QCA;
|
|
+}
|
|
+
|
|
+static bool
|
|
+qca8k_lag_can_offload(struct dsa_switch *ds,
|
|
+ struct net_device *lag,
|
|
+ struct netdev_lag_upper_info *info)
|
|
+{
|
|
+ struct dsa_port *dp;
|
|
+ int id, members = 0;
|
|
+
|
|
+ id = dsa_lag_id(ds->dst, lag);
|
|
+ if (id < 0 || id >= ds->num_lag_ids)
|
|
+ return false;
|
|
+
|
|
+ dsa_lag_foreach_port(dp, ds->dst, lag)
|
|
+ /* Includes the port joining the LAG */
|
|
+ members++;
|
|
+
|
|
+ if (members > QCA8K_NUM_PORTS_FOR_LAG)
|
|
+ return false;
|
|
+
|
|
+ if (info->tx_type != NETDEV_LAG_TX_TYPE_HASH)
|
|
+ return false;
|
|
+
|
|
+ if (info->hash_type != NETDEV_LAG_HASH_L2 &&
|
|
+ info->hash_type != NETDEV_LAG_HASH_L23)
|
|
+ return false;
|
|
+
|
|
+ return true;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_lag_setup_hash(struct dsa_switch *ds,
|
|
+ struct net_device *lag,
|
|
+ struct netdev_lag_upper_info *info)
|
|
+{
|
|
+ struct qca8k_priv *priv = ds->priv;
|
|
+ bool unique_lag = true;
|
|
+ u32 hash = 0;
|
|
+ int i, id;
|
|
+
|
|
+ id = dsa_lag_id(ds->dst, lag);
|
|
+
|
|
+ switch (info->hash_type) {
|
|
+ case NETDEV_LAG_HASH_L23:
|
|
+ hash |= QCA8K_TRUNK_HASH_SIP_EN;
|
|
+ hash |= QCA8K_TRUNK_HASH_DIP_EN;
|
|
+ fallthrough;
|
|
+ case NETDEV_LAG_HASH_L2:
|
|
+ hash |= QCA8K_TRUNK_HASH_SA_EN;
|
|
+ hash |= QCA8K_TRUNK_HASH_DA_EN;
|
|
+ break;
|
|
+ default: /* We should NEVER reach this */
|
|
+ return -EOPNOTSUPP;
|
|
+ }
|
|
+
|
|
+ /* Check if we are the unique configured LAG */
|
|
+ dsa_lags_foreach_id(i, ds->dst)
|
|
+ if (i != id && dsa_lag_dev(ds->dst, i)) {
|
|
+ unique_lag = false;
|
|
+ break;
|
|
+ }
|
|
+
|
|
+ /* Hash Mode is global. Make sure the same Hash Mode
|
|
+ * is set to all the 4 possible lag.
|
|
+ * If we are the unique LAG we can set whatever hash
|
|
+ * mode we want.
|
|
+ * To change hash mode it's needed to remove all LAG
|
|
+ * and change the mode with the latest.
|
|
+ */
|
|
+ if (unique_lag) {
|
|
+ priv->lag_hash_mode = hash;
|
|
+ } else if (priv->lag_hash_mode != hash) {
|
|
+ netdev_err(lag, "Error: Mismateched Hash Mode across different lag is not supported\n");
|
|
+ return -EOPNOTSUPP;
|
|
+ }
|
|
+
|
|
+ return regmap_update_bits(priv->regmap, QCA8K_TRUNK_HASH_EN_CTRL,
|
|
+ QCA8K_TRUNK_HASH_MASK, hash);
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_lag_refresh_portmap(struct dsa_switch *ds, int port,
|
|
+ struct net_device *lag, bool delete)
|
|
+{
|
|
+ struct qca8k_priv *priv = ds->priv;
|
|
+ int ret, id, i;
|
|
+ u32 val;
|
|
+
|
|
+ id = dsa_lag_id(ds->dst, lag);
|
|
+
|
|
+ /* Read current port member */
|
|
+ ret = regmap_read(priv->regmap, QCA8K_REG_GOL_TRUNK_CTRL0, &val);
|
|
+ if (ret)
|
|
+ return ret;
|
|
+
|
|
+ /* Shift val to the correct trunk */
|
|
+ val >>= QCA8K_REG_GOL_TRUNK_SHIFT(id);
|
|
+ val &= QCA8K_REG_GOL_TRUNK_MEMBER_MASK;
|
|
+ if (delete)
|
|
+ val &= ~BIT(port);
|
|
+ else
|
|
+ val |= BIT(port);
|
|
+
|
|
+ /* Update port member. With empty portmap disable trunk */
|
|
+ ret = regmap_update_bits(priv->regmap, QCA8K_REG_GOL_TRUNK_CTRL0,
|
|
+ QCA8K_REG_GOL_TRUNK_MEMBER(id) |
|
|
+ QCA8K_REG_GOL_TRUNK_EN(id),
|
|
+ !val << QCA8K_REG_GOL_TRUNK_SHIFT(id) |
|
|
+ val << QCA8K_REG_GOL_TRUNK_SHIFT(id));
|
|
+
|
|
+ /* Search empty member if adding or port on deleting */
|
|
+ for (i = 0; i < QCA8K_NUM_PORTS_FOR_LAG; i++) {
|
|
+ ret = regmap_read(priv->regmap, QCA8K_REG_GOL_TRUNK_CTRL(id), &val);
|
|
+ if (ret)
|
|
+ return ret;
|
|
+
|
|
+ val >>= QCA8K_REG_GOL_TRUNK_ID_MEM_ID_SHIFT(id, i);
|
|
+ val &= QCA8K_REG_GOL_TRUNK_ID_MEM_ID_MASK;
|
|
+
|
|
+ if (delete) {
|
|
+ /* If port flagged to be disabled assume this member is
|
|
+ * empty
|
|
+ */
|
|
+ if (val != QCA8K_REG_GOL_TRUNK_ID_MEM_ID_EN_MASK)
|
|
+ continue;
|
|
+
|
|
+ val &= QCA8K_REG_GOL_TRUNK_ID_MEM_ID_PORT_MASK;
|
|
+ if (val != port)
|
|
+ continue;
|
|
+ } else {
|
|
+ /* If port flagged to be enabled assume this member is
|
|
+ * already set
|
|
+ */
|
|
+ if (val == QCA8K_REG_GOL_TRUNK_ID_MEM_ID_EN_MASK)
|
|
+ continue;
|
|
+ }
|
|
+
|
|
+ /* We have found the member to add/remove */
|
|
+ break;
|
|
+ }
|
|
+
|
|
+ /* Set port in the correct port mask or disable port if in delete mode */
|
|
+ return regmap_update_bits(priv->regmap, QCA8K_REG_GOL_TRUNK_CTRL(id),
|
|
+ QCA8K_REG_GOL_TRUNK_ID_MEM_ID_EN(id, i) |
|
|
+ QCA8K_REG_GOL_TRUNK_ID_MEM_ID_PORT(id, i),
|
|
+ !delete << QCA8K_REG_GOL_TRUNK_ID_MEM_ID_SHIFT(id, i) |
|
|
+ port << QCA8K_REG_GOL_TRUNK_ID_MEM_ID_SHIFT(id, i));
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_port_lag_join(struct dsa_switch *ds, int port,
|
|
+ struct net_device *lag,
|
|
+ struct netdev_lag_upper_info *info)
|
|
+{
|
|
+ int ret;
|
|
+
|
|
+ if (!qca8k_lag_can_offload(ds, lag, info))
|
|
+ return -EOPNOTSUPP;
|
|
+
|
|
+ ret = qca8k_lag_setup_hash(ds, lag, info);
|
|
+ if (ret)
|
|
+ return ret;
|
|
+
|
|
+ return qca8k_lag_refresh_portmap(ds, port, lag, false);
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_port_lag_leave(struct dsa_switch *ds, int port,
|
|
+ struct net_device *lag)
|
|
+{
|
|
+ return qca8k_lag_refresh_portmap(ds, port, lag, true);
|
|
+}
|
|
+
|
|
+static void
|
|
+qca8k_master_change(struct dsa_switch *ds, const struct net_device *master,
|
|
+ bool operational)
|
|
+{
|
|
+ struct dsa_port *dp = master->dsa_ptr;
|
|
+ struct qca8k_priv *priv = ds->priv;
|
|
+
|
|
+ /* Ethernet MIB/MDIO is only supported for CPU port 0 */
|
|
+ if (dp->index != 0)
|
|
+ return;
|
|
+
|
|
+ mutex_lock(&priv->mgmt_eth_data.mutex);
|
|
+ mutex_lock(&priv->mib_eth_data.mutex);
|
|
+
|
|
+ priv->mgmt_master = operational ? (struct net_device *)master : NULL;
|
|
+
|
|
+ mutex_unlock(&priv->mib_eth_data.mutex);
|
|
+ mutex_unlock(&priv->mgmt_eth_data.mutex);
|
|
+}
|
|
+
|
|
+static int qca8k_connect_tag_protocol(struct dsa_switch *ds,
|
|
+ enum dsa_tag_protocol proto)
|
|
+{
|
|
+ struct qca_tagger_data *tagger_data;
|
|
+
|
|
+ switch (proto) {
|
|
+ case DSA_TAG_PROTO_QCA:
|
|
+ tagger_data = ds->tagger_data;
|
|
+
|
|
+ tagger_data->rw_reg_ack_handler = qca8k_rw_reg_ack_handler;
|
|
+ tagger_data->mib_autocast_handler = qca8k_mib_autocast_handler;
|
|
+
|
|
+ break;
|
|
+ default:
|
|
+ return -EOPNOTSUPP;
|
|
+ }
|
|
+
|
|
+ return 0;
|
|
+}
|
|
+
|
|
+static const struct dsa_switch_ops qca8k_switch_ops = {
|
|
+ .get_tag_protocol = qca8k_get_tag_protocol,
|
|
+ .setup = qca8k_setup,
|
|
+ .get_strings = qca8k_get_strings,
|
|
+ .get_ethtool_stats = qca8k_get_ethtool_stats,
|
|
+ .get_sset_count = qca8k_get_sset_count,
|
|
+ .set_ageing_time = qca8k_set_ageing_time,
|
|
+ .get_mac_eee = qca8k_get_mac_eee,
|
|
+ .set_mac_eee = qca8k_set_mac_eee,
|
|
+ .port_enable = qca8k_port_enable,
|
|
+ .port_disable = qca8k_port_disable,
|
|
+ .port_change_mtu = qca8k_port_change_mtu,
|
|
+ .port_max_mtu = qca8k_port_max_mtu,
|
|
+ .port_stp_state_set = qca8k_port_stp_state_set,
|
|
+ .port_bridge_join = qca8k_port_bridge_join,
|
|
+ .port_bridge_leave = qca8k_port_bridge_leave,
|
|
+ .port_fast_age = qca8k_port_fast_age,
|
|
+ .port_fdb_add = qca8k_port_fdb_add,
|
|
+ .port_fdb_del = qca8k_port_fdb_del,
|
|
+ .port_fdb_dump = qca8k_port_fdb_dump,
|
|
+ .port_mdb_add = qca8k_port_mdb_add,
|
|
+ .port_mdb_del = qca8k_port_mdb_del,
|
|
+ .port_mirror_add = qca8k_port_mirror_add,
|
|
+ .port_mirror_del = qca8k_port_mirror_del,
|
|
+ .port_vlan_filtering = qca8k_port_vlan_filtering,
|
|
+ .port_vlan_add = qca8k_port_vlan_add,
|
|
+ .port_vlan_del = qca8k_port_vlan_del,
|
|
+ .phylink_validate = qca8k_phylink_validate,
|
|
+ .phylink_mac_link_state = qca8k_phylink_mac_link_state,
|
|
+ .phylink_mac_config = qca8k_phylink_mac_config,
|
|
+ .phylink_mac_link_down = qca8k_phylink_mac_link_down,
|
|
+ .phylink_mac_link_up = qca8k_phylink_mac_link_up,
|
|
+ .get_phy_flags = qca8k_get_phy_flags,
|
|
+ .port_lag_join = qca8k_port_lag_join,
|
|
+ .port_lag_leave = qca8k_port_lag_leave,
|
|
+ .master_state_change = qca8k_master_change,
|
|
+ .connect_tag_protocol = qca8k_connect_tag_protocol,
|
|
+};
|
|
+
|
|
+static int qca8k_read_switch_id(struct qca8k_priv *priv)
|
|
+{
|
|
+ const struct qca8k_match_data *data;
|
|
+ u32 val;
|
|
+ u8 id;
|
|
+ int ret;
|
|
+
|
|
+ /* get the switches ID from the compatible */
|
|
+ data = of_device_get_match_data(priv->dev);
|
|
+ if (!data)
|
|
+ return -ENODEV;
|
|
+
|
|
+ ret = qca8k_read(priv, QCA8K_REG_MASK_CTRL, &val);
|
|
+ if (ret < 0)
|
|
+ return -ENODEV;
|
|
+
|
|
+ id = QCA8K_MASK_CTRL_DEVICE_ID(val);
|
|
+ if (id != data->id) {
|
|
+ dev_err(priv->dev, "Switch id detected %x but expected %x", id, data->id);
|
|
+ return -ENODEV;
|
|
+ }
|
|
+
|
|
+ priv->switch_id = id;
|
|
+
|
|
+ /* Save revision to communicate to the internal PHY driver */
|
|
+ priv->switch_revision = QCA8K_MASK_CTRL_REV_ID(val);
|
|
+
|
|
+ return 0;
|
|
+}
|
|
+
|
|
+static int
|
|
+qca8k_sw_probe(struct mdio_device *mdiodev)
|
|
+{
|
|
+ struct qca8k_priv *priv;
|
|
+ int ret;
|
|
+
|
|
+ /* allocate the private data struct so that we can probe the switches
|
|
+ * ID register
|
|
+ */
|
|
+ priv = devm_kzalloc(&mdiodev->dev, sizeof(*priv), GFP_KERNEL);
|
|
+ if (!priv)
|
|
+ return -ENOMEM;
|
|
+
|
|
+ priv->bus = mdiodev->bus;
|
|
+ priv->dev = &mdiodev->dev;
|
|
+
|
|
+ priv->reset_gpio = devm_gpiod_get_optional(priv->dev, "reset",
|
|
+ GPIOD_ASIS);
|
|
+ if (IS_ERR(priv->reset_gpio))
|
|
+ return PTR_ERR(priv->reset_gpio);
|
|
+
|
|
+ if (priv->reset_gpio) {
|
|
+ gpiod_set_value_cansleep(priv->reset_gpio, 1);
|
|
+ /* The active low duration must be greater than 10 ms
|
|
+ * and checkpatch.pl wants 20 ms.
|
|
+ */
|
|
+ msleep(20);
|
|
+ gpiod_set_value_cansleep(priv->reset_gpio, 0);
|
|
+ }
|
|
+
|
|
+ /* Start by setting up the register mapping */
|
|
+ priv->regmap = devm_regmap_init(&mdiodev->dev, NULL, priv,
|
|
+ &qca8k_regmap_config);
|
|
+ if (IS_ERR(priv->regmap)) {
|
|
+ dev_err(priv->dev, "regmap initialization failed");
|
|
+ return PTR_ERR(priv->regmap);
|
|
+ }
|
|
+
|
|
+ priv->mdio_cache.page = 0xffff;
|
|
+ priv->mdio_cache.lo = 0xffff;
|
|
+ priv->mdio_cache.hi = 0xffff;
|
|
+
|
|
+ /* Check the detected switch id */
|
|
+ ret = qca8k_read_switch_id(priv);
|
|
+ if (ret)
|
|
+ return ret;
|
|
+
|
|
+ priv->ds = devm_kzalloc(&mdiodev->dev, sizeof(*priv->ds), GFP_KERNEL);
|
|
+ if (!priv->ds)
|
|
+ return -ENOMEM;
|
|
+
|
|
+ mutex_init(&priv->mgmt_eth_data.mutex);
|
|
+ init_completion(&priv->mgmt_eth_data.rw_done);
|
|
+
|
|
+ mutex_init(&priv->mib_eth_data.mutex);
|
|
+ init_completion(&priv->mib_eth_data.rw_done);
|
|
+
|
|
+ priv->ds->dev = &mdiodev->dev;
|
|
+ priv->ds->num_ports = QCA8K_NUM_PORTS;
|
|
+ priv->ds->priv = priv;
|
|
+ priv->ds->ops = &qca8k_switch_ops;
|
|
+ mutex_init(&priv->reg_mutex);
|
|
+ dev_set_drvdata(&mdiodev->dev, priv);
|
|
+
|
|
+ return dsa_register_switch(priv->ds);
|
|
+}
|
|
+
|
|
+static void
|
|
+qca8k_sw_remove(struct mdio_device *mdiodev)
|
|
+{
|
|
+ struct qca8k_priv *priv = dev_get_drvdata(&mdiodev->dev);
|
|
+ int i;
|
|
+
|
|
+ if (!priv)
|
|
+ return;
|
|
+
|
|
+ for (i = 0; i < QCA8K_NUM_PORTS; i++)
|
|
+ qca8k_port_set_status(priv, i, 0);
|
|
+
|
|
+ dsa_unregister_switch(priv->ds);
|
|
+
|
|
+ dev_set_drvdata(&mdiodev->dev, NULL);
|
|
+}
|
|
+
|
|
+static void qca8k_sw_shutdown(struct mdio_device *mdiodev)
|
|
+{
|
|
+ struct qca8k_priv *priv = dev_get_drvdata(&mdiodev->dev);
|
|
+
|
|
+ if (!priv)
|
|
+ return;
|
|
+
|
|
+ dsa_switch_shutdown(priv->ds);
|
|
+
|
|
+ dev_set_drvdata(&mdiodev->dev, NULL);
|
|
+}
|
|
+
|
|
+#ifdef CONFIG_PM_SLEEP
|
|
+static void
|
|
+qca8k_set_pm(struct qca8k_priv *priv, int enable)
|
|
+{
|
|
+ int port;
|
|
+
|
|
+ for (port = 0; port < QCA8K_NUM_PORTS; port++) {
|
|
+ /* Do not enable on resume if the port was
|
|
+ * disabled before.
|
|
+ */
|
|
+ if (!(priv->port_enabled_map & BIT(port)))
|
|
+ continue;
|
|
+
|
|
+ qca8k_port_set_status(priv, port, enable);
|
|
+ }
|
|
+}
|
|
+
|
|
+static int qca8k_suspend(struct device *dev)
|
|
+{
|
|
+ struct qca8k_priv *priv = dev_get_drvdata(dev);
|
|
+
|
|
+ qca8k_set_pm(priv, 0);
|
|
+
|
|
+ return dsa_switch_suspend(priv->ds);
|
|
+}
|
|
+
|
|
+static int qca8k_resume(struct device *dev)
|
|
+{
|
|
+ struct qca8k_priv *priv = dev_get_drvdata(dev);
|
|
+
|
|
+ qca8k_set_pm(priv, 1);
|
|
+
|
|
+ return dsa_switch_resume(priv->ds);
|
|
+}
|
|
+#endif /* CONFIG_PM_SLEEP */
|
|
+
|
|
+static SIMPLE_DEV_PM_OPS(qca8k_pm_ops,
|
|
+ qca8k_suspend, qca8k_resume);
|
|
+
|
|
+static const struct qca8k_match_data qca8327 = {
|
|
+ .id = QCA8K_ID_QCA8327,
|
|
+ .reduced_package = true,
|
|
+ .mib_count = QCA8K_QCA832X_MIB_COUNT,
|
|
+};
|
|
+
|
|
+static const struct qca8k_match_data qca8328 = {
|
|
+ .id = QCA8K_ID_QCA8327,
|
|
+ .mib_count = QCA8K_QCA832X_MIB_COUNT,
|
|
+};
|
|
+
|
|
+static const struct qca8k_match_data qca833x = {
|
|
+ .id = QCA8K_ID_QCA8337,
|
|
+ .mib_count = QCA8K_QCA833X_MIB_COUNT,
|
|
+};
|
|
+
|
|
+static const struct of_device_id qca8k_of_match[] = {
|
|
+ { .compatible = "qca,qca8327", .data = &qca8327 },
|
|
+ { .compatible = "qca,qca8328", .data = &qca8328 },
|
|
+ { .compatible = "qca,qca8334", .data = &qca833x },
|
|
+ { .compatible = "qca,qca8337", .data = &qca833x },
|
|
+ { /* sentinel */ },
|
|
+};
|
|
+
|
|
+static struct mdio_driver qca8kmdio_driver = {
|
|
+ .probe = qca8k_sw_probe,
|
|
+ .remove = qca8k_sw_remove,
|
|
+ .shutdown = qca8k_sw_shutdown,
|
|
+ .mdiodrv.driver = {
|
|
+ .name = "qca8k",
|
|
+ .of_match_table = qca8k_of_match,
|
|
+ .pm = &qca8k_pm_ops,
|
|
+ },
|
|
+};
|
|
+
|
|
+mdio_module_driver(qca8kmdio_driver);
|
|
+
|
|
+MODULE_AUTHOR("Mathieu Olivari, John Crispin <john@phrozen.org>");
|
|
+MODULE_DESCRIPTION("Driver for QCA8K ethernet switch family");
|
|
+MODULE_LICENSE("GPL v2");
|
|
+MODULE_ALIAS("platform:qca8k");
|
|
--- /dev/null
|
|
+++ b/drivers/net/dsa/qca/qca8k.h
|
|
@@ -0,0 +1,411 @@
|
|
+/* SPDX-License-Identifier: GPL-2.0-only */
|
|
+/*
|
|
+ * Copyright (C) 2009 Felix Fietkau <nbd@nbd.name>
|
|
+ * Copyright (C) 2011-2012 Gabor Juhos <juhosg@openwrt.org>
|
|
+ * Copyright (c) 2015, The Linux Foundation. All rights reserved.
|
|
+ */
|
|
+
|
|
+#ifndef __QCA8K_H
|
|
+#define __QCA8K_H
|
|
+
|
|
+#include <linux/delay.h>
|
|
+#include <linux/regmap.h>
|
|
+#include <linux/gpio.h>
|
|
+#include <linux/dsa/tag_qca.h>
|
|
+
|
|
+#define QCA8K_ETHERNET_MDIO_PRIORITY 7
|
|
+#define QCA8K_ETHERNET_PHY_PRIORITY 6
|
|
+#define QCA8K_ETHERNET_TIMEOUT 100
|
|
+
|
|
+#define QCA8K_NUM_PORTS 7
|
|
+#define QCA8K_NUM_CPU_PORTS 2
|
|
+#define QCA8K_MAX_MTU 9000
|
|
+#define QCA8K_NUM_LAGS 4
|
|
+#define QCA8K_NUM_PORTS_FOR_LAG 4
|
|
+
|
|
+#define PHY_ID_QCA8327 0x004dd034
|
|
+#define QCA8K_ID_QCA8327 0x12
|
|
+#define PHY_ID_QCA8337 0x004dd036
|
|
+#define QCA8K_ID_QCA8337 0x13
|
|
+
|
|
+#define QCA8K_QCA832X_MIB_COUNT 39
|
|
+#define QCA8K_QCA833X_MIB_COUNT 41
|
|
+
|
|
+#define QCA8K_BUSY_WAIT_TIMEOUT 2000
|
|
+
|
|
+#define QCA8K_NUM_FDB_RECORDS 2048
|
|
+
|
|
+#define QCA8K_PORT_VID_DEF 1
|
|
+
|
|
+/* Global control registers */
|
|
+#define QCA8K_REG_MASK_CTRL 0x000
|
|
+#define QCA8K_MASK_CTRL_REV_ID_MASK GENMASK(7, 0)
|
|
+#define QCA8K_MASK_CTRL_REV_ID(x) FIELD_GET(QCA8K_MASK_CTRL_REV_ID_MASK, x)
|
|
+#define QCA8K_MASK_CTRL_DEVICE_ID_MASK GENMASK(15, 8)
|
|
+#define QCA8K_MASK_CTRL_DEVICE_ID(x) FIELD_GET(QCA8K_MASK_CTRL_DEVICE_ID_MASK, x)
|
|
+#define QCA8K_REG_PORT0_PAD_CTRL 0x004
|
|
+#define QCA8K_PORT0_PAD_MAC06_EXCHANGE_EN BIT(31)
|
|
+#define QCA8K_PORT0_PAD_SGMII_RXCLK_FALLING_EDGE BIT(19)
|
|
+#define QCA8K_PORT0_PAD_SGMII_TXCLK_FALLING_EDGE BIT(18)
|
|
+#define QCA8K_REG_PORT5_PAD_CTRL 0x008
|
|
+#define QCA8K_REG_PORT6_PAD_CTRL 0x00c
|
|
+#define QCA8K_PORT_PAD_RGMII_EN BIT(26)
|
|
+#define QCA8K_PORT_PAD_RGMII_TX_DELAY_MASK GENMASK(23, 22)
|
|
+#define QCA8K_PORT_PAD_RGMII_TX_DELAY(x) FIELD_PREP(QCA8K_PORT_PAD_RGMII_TX_DELAY_MASK, x)
|
|
+#define QCA8K_PORT_PAD_RGMII_RX_DELAY_MASK GENMASK(21, 20)
|
|
+#define QCA8K_PORT_PAD_RGMII_RX_DELAY(x) FIELD_PREP(QCA8K_PORT_PAD_RGMII_RX_DELAY_MASK, x)
|
|
+#define QCA8K_PORT_PAD_RGMII_TX_DELAY_EN BIT(25)
|
|
+#define QCA8K_PORT_PAD_RGMII_RX_DELAY_EN BIT(24)
|
|
+#define QCA8K_PORT_PAD_SGMII_EN BIT(7)
|
|
+#define QCA8K_REG_PWS 0x010
|
|
+#define QCA8K_PWS_POWER_ON_SEL BIT(31)
|
|
+/* This reg is only valid for QCA832x and toggle the package
|
|
+ * type from 176 pin (by default) to 148 pin used on QCA8327
|
|
+ */
|
|
+#define QCA8327_PWS_PACKAGE148_EN BIT(30)
|
|
+#define QCA8K_PWS_LED_OPEN_EN_CSR BIT(24)
|
|
+#define QCA8K_PWS_SERDES_AEN_DIS BIT(7)
|
|
+#define QCA8K_REG_MODULE_EN 0x030
|
|
+#define QCA8K_MODULE_EN_MIB BIT(0)
|
|
+#define QCA8K_REG_MIB 0x034
|
|
+#define QCA8K_MIB_FUNC GENMASK(26, 24)
|
|
+#define QCA8K_MIB_CPU_KEEP BIT(20)
|
|
+#define QCA8K_MIB_BUSY BIT(17)
|
|
+#define QCA8K_MDIO_MASTER_CTRL 0x3c
|
|
+#define QCA8K_MDIO_MASTER_BUSY BIT(31)
|
|
+#define QCA8K_MDIO_MASTER_EN BIT(30)
|
|
+#define QCA8K_MDIO_MASTER_READ BIT(27)
|
|
+#define QCA8K_MDIO_MASTER_WRITE 0
|
|
+#define QCA8K_MDIO_MASTER_SUP_PRE BIT(26)
|
|
+#define QCA8K_MDIO_MASTER_PHY_ADDR_MASK GENMASK(25, 21)
|
|
+#define QCA8K_MDIO_MASTER_PHY_ADDR(x) FIELD_PREP(QCA8K_MDIO_MASTER_PHY_ADDR_MASK, x)
|
|
+#define QCA8K_MDIO_MASTER_REG_ADDR_MASK GENMASK(20, 16)
|
|
+#define QCA8K_MDIO_MASTER_REG_ADDR(x) FIELD_PREP(QCA8K_MDIO_MASTER_REG_ADDR_MASK, x)
|
|
+#define QCA8K_MDIO_MASTER_DATA_MASK GENMASK(15, 0)
|
|
+#define QCA8K_MDIO_MASTER_DATA(x) FIELD_PREP(QCA8K_MDIO_MASTER_DATA_MASK, x)
|
|
+#define QCA8K_MDIO_MASTER_MAX_PORTS 5
|
|
+#define QCA8K_MDIO_MASTER_MAX_REG 32
|
|
+#define QCA8K_GOL_MAC_ADDR0 0x60
|
|
+#define QCA8K_GOL_MAC_ADDR1 0x64
|
|
+#define QCA8K_MAX_FRAME_SIZE 0x78
|
|
+#define QCA8K_REG_PORT_STATUS(_i) (0x07c + (_i) * 4)
|
|
+#define QCA8K_PORT_STATUS_SPEED GENMASK(1, 0)
|
|
+#define QCA8K_PORT_STATUS_SPEED_10 0
|
|
+#define QCA8K_PORT_STATUS_SPEED_100 0x1
|
|
+#define QCA8K_PORT_STATUS_SPEED_1000 0x2
|
|
+#define QCA8K_PORT_STATUS_TXMAC BIT(2)
|
|
+#define QCA8K_PORT_STATUS_RXMAC BIT(3)
|
|
+#define QCA8K_PORT_STATUS_TXFLOW BIT(4)
|
|
+#define QCA8K_PORT_STATUS_RXFLOW BIT(5)
|
|
+#define QCA8K_PORT_STATUS_DUPLEX BIT(6)
|
|
+#define QCA8K_PORT_STATUS_LINK_UP BIT(8)
|
|
+#define QCA8K_PORT_STATUS_LINK_AUTO BIT(9)
|
|
+#define QCA8K_PORT_STATUS_LINK_PAUSE BIT(10)
|
|
+#define QCA8K_PORT_STATUS_FLOW_AUTO BIT(12)
|
|
+#define QCA8K_REG_PORT_HDR_CTRL(_i) (0x9c + (_i * 4))
|
|
+#define QCA8K_PORT_HDR_CTRL_RX_MASK GENMASK(3, 2)
|
|
+#define QCA8K_PORT_HDR_CTRL_TX_MASK GENMASK(1, 0)
|
|
+#define QCA8K_PORT_HDR_CTRL_ALL 2
|
|
+#define QCA8K_PORT_HDR_CTRL_MGMT 1
|
|
+#define QCA8K_PORT_HDR_CTRL_NONE 0
|
|
+#define QCA8K_REG_SGMII_CTRL 0x0e0
|
|
+#define QCA8K_SGMII_EN_PLL BIT(1)
|
|
+#define QCA8K_SGMII_EN_RX BIT(2)
|
|
+#define QCA8K_SGMII_EN_TX BIT(3)
|
|
+#define QCA8K_SGMII_EN_SD BIT(4)
|
|
+#define QCA8K_SGMII_CLK125M_DELAY BIT(7)
|
|
+#define QCA8K_SGMII_MODE_CTRL_MASK GENMASK(23, 22)
|
|
+#define QCA8K_SGMII_MODE_CTRL(x) FIELD_PREP(QCA8K_SGMII_MODE_CTRL_MASK, x)
|
|
+#define QCA8K_SGMII_MODE_CTRL_BASEX QCA8K_SGMII_MODE_CTRL(0x0)
|
|
+#define QCA8K_SGMII_MODE_CTRL_PHY QCA8K_SGMII_MODE_CTRL(0x1)
|
|
+#define QCA8K_SGMII_MODE_CTRL_MAC QCA8K_SGMII_MODE_CTRL(0x2)
|
|
+
|
|
+/* MAC_PWR_SEL registers */
|
|
+#define QCA8K_REG_MAC_PWR_SEL 0x0e4
|
|
+#define QCA8K_MAC_PWR_RGMII1_1_8V BIT(18)
|
|
+#define QCA8K_MAC_PWR_RGMII0_1_8V BIT(19)
|
|
+
|
|
+/* EEE control registers */
|
|
+#define QCA8K_REG_EEE_CTRL 0x100
|
|
+#define QCA8K_REG_EEE_CTRL_LPI_EN(_i) ((_i + 1) * 2)
|
|
+
|
|
+/* TRUNK_HASH_EN registers */
|
|
+#define QCA8K_TRUNK_HASH_EN_CTRL 0x270
|
|
+#define QCA8K_TRUNK_HASH_SIP_EN BIT(3)
|
|
+#define QCA8K_TRUNK_HASH_DIP_EN BIT(2)
|
|
+#define QCA8K_TRUNK_HASH_SA_EN BIT(1)
|
|
+#define QCA8K_TRUNK_HASH_DA_EN BIT(0)
|
|
+#define QCA8K_TRUNK_HASH_MASK GENMASK(3, 0)
|
|
+
|
|
+/* ACL registers */
|
|
+#define QCA8K_REG_PORT_VLAN_CTRL0(_i) (0x420 + (_i * 8))
|
|
+#define QCA8K_PORT_VLAN_CVID_MASK GENMASK(27, 16)
|
|
+#define QCA8K_PORT_VLAN_CVID(x) FIELD_PREP(QCA8K_PORT_VLAN_CVID_MASK, x)
|
|
+#define QCA8K_PORT_VLAN_SVID_MASK GENMASK(11, 0)
|
|
+#define QCA8K_PORT_VLAN_SVID(x) FIELD_PREP(QCA8K_PORT_VLAN_SVID_MASK, x)
|
|
+#define QCA8K_REG_PORT_VLAN_CTRL1(_i) (0x424 + (_i * 8))
|
|
+#define QCA8K_REG_IPV4_PRI_BASE_ADDR 0x470
|
|
+#define QCA8K_REG_IPV4_PRI_ADDR_MASK 0x474
|
|
+
|
|
+/* Lookup registers */
|
|
+#define QCA8K_REG_ATU_DATA0 0x600
|
|
+#define QCA8K_ATU_ADDR2_MASK GENMASK(31, 24)
|
|
+#define QCA8K_ATU_ADDR3_MASK GENMASK(23, 16)
|
|
+#define QCA8K_ATU_ADDR4_MASK GENMASK(15, 8)
|
|
+#define QCA8K_ATU_ADDR5_MASK GENMASK(7, 0)
|
|
+#define QCA8K_REG_ATU_DATA1 0x604
|
|
+#define QCA8K_ATU_PORT_MASK GENMASK(22, 16)
|
|
+#define QCA8K_ATU_ADDR0_MASK GENMASK(15, 8)
|
|
+#define QCA8K_ATU_ADDR1_MASK GENMASK(7, 0)
|
|
+#define QCA8K_REG_ATU_DATA2 0x608
|
|
+#define QCA8K_ATU_VID_MASK GENMASK(19, 8)
|
|
+#define QCA8K_ATU_STATUS_MASK GENMASK(3, 0)
|
|
+#define QCA8K_ATU_STATUS_STATIC 0xf
|
|
+#define QCA8K_REG_ATU_FUNC 0x60c
|
|
+#define QCA8K_ATU_FUNC_BUSY BIT(31)
|
|
+#define QCA8K_ATU_FUNC_PORT_EN BIT(14)
|
|
+#define QCA8K_ATU_FUNC_MULTI_EN BIT(13)
|
|
+#define QCA8K_ATU_FUNC_FULL BIT(12)
|
|
+#define QCA8K_ATU_FUNC_PORT_MASK GENMASK(11, 8)
|
|
+#define QCA8K_REG_VTU_FUNC0 0x610
|
|
+#define QCA8K_VTU_FUNC0_VALID BIT(20)
|
|
+#define QCA8K_VTU_FUNC0_IVL_EN BIT(19)
|
|
+/* QCA8K_VTU_FUNC0_EG_MODE_MASK GENMASK(17, 4)
|
|
+ * It does contain VLAN_MODE for each port [5:4] for port0,
|
|
+ * [7:6] for port1 ... [17:16] for port6. Use virtual port
|
|
+ * define to handle this.
|
|
+ */
|
|
+#define QCA8K_VTU_FUNC0_EG_MODE_PORT_SHIFT(_i) (4 + (_i) * 2)
|
|
+#define QCA8K_VTU_FUNC0_EG_MODE_MASK GENMASK(1, 0)
|
|
+#define QCA8K_VTU_FUNC0_EG_MODE_PORT_MASK(_i) (GENMASK(1, 0) << QCA8K_VTU_FUNC0_EG_MODE_PORT_SHIFT(_i))
|
|
+#define QCA8K_VTU_FUNC0_EG_MODE_UNMOD FIELD_PREP(QCA8K_VTU_FUNC0_EG_MODE_MASK, 0x0)
|
|
+#define QCA8K_VTU_FUNC0_EG_MODE_PORT_UNMOD(_i) (QCA8K_VTU_FUNC0_EG_MODE_UNMOD << QCA8K_VTU_FUNC0_EG_MODE_PORT_SHIFT(_i))
|
|
+#define QCA8K_VTU_FUNC0_EG_MODE_UNTAG FIELD_PREP(QCA8K_VTU_FUNC0_EG_MODE_MASK, 0x1)
|
|
+#define QCA8K_VTU_FUNC0_EG_MODE_PORT_UNTAG(_i) (QCA8K_VTU_FUNC0_EG_MODE_UNTAG << QCA8K_VTU_FUNC0_EG_MODE_PORT_SHIFT(_i))
|
|
+#define QCA8K_VTU_FUNC0_EG_MODE_TAG FIELD_PREP(QCA8K_VTU_FUNC0_EG_MODE_MASK, 0x2)
|
|
+#define QCA8K_VTU_FUNC0_EG_MODE_PORT_TAG(_i) (QCA8K_VTU_FUNC0_EG_MODE_TAG << QCA8K_VTU_FUNC0_EG_MODE_PORT_SHIFT(_i))
|
|
+#define QCA8K_VTU_FUNC0_EG_MODE_NOT FIELD_PREP(QCA8K_VTU_FUNC0_EG_MODE_MASK, 0x3)
|
|
+#define QCA8K_VTU_FUNC0_EG_MODE_PORT_NOT(_i) (QCA8K_VTU_FUNC0_EG_MODE_NOT << QCA8K_VTU_FUNC0_EG_MODE_PORT_SHIFT(_i))
|
|
+#define QCA8K_REG_VTU_FUNC1 0x614
|
|
+#define QCA8K_VTU_FUNC1_BUSY BIT(31)
|
|
+#define QCA8K_VTU_FUNC1_VID_MASK GENMASK(27, 16)
|
|
+#define QCA8K_VTU_FUNC1_FULL BIT(4)
|
|
+#define QCA8K_REG_ATU_CTRL 0x618
|
|
+#define QCA8K_ATU_AGE_TIME_MASK GENMASK(15, 0)
|
|
+#define QCA8K_ATU_AGE_TIME(x) FIELD_PREP(QCA8K_ATU_AGE_TIME_MASK, (x))
|
|
+#define QCA8K_REG_GLOBAL_FW_CTRL0 0x620
|
|
+#define QCA8K_GLOBAL_FW_CTRL0_CPU_PORT_EN BIT(10)
|
|
+#define QCA8K_GLOBAL_FW_CTRL0_MIRROR_PORT_NUM GENMASK(7, 4)
|
|
+#define QCA8K_REG_GLOBAL_FW_CTRL1 0x624
|
|
+#define QCA8K_GLOBAL_FW_CTRL1_IGMP_DP_MASK GENMASK(30, 24)
|
|
+#define QCA8K_GLOBAL_FW_CTRL1_BC_DP_MASK GENMASK(22, 16)
|
|
+#define QCA8K_GLOBAL_FW_CTRL1_MC_DP_MASK GENMASK(14, 8)
|
|
+#define QCA8K_GLOBAL_FW_CTRL1_UC_DP_MASK GENMASK(6, 0)
|
|
+#define QCA8K_PORT_LOOKUP_CTRL(_i) (0x660 + (_i) * 0xc)
|
|
+#define QCA8K_PORT_LOOKUP_MEMBER GENMASK(6, 0)
|
|
+#define QCA8K_PORT_LOOKUP_VLAN_MODE_MASK GENMASK(9, 8)
|
|
+#define QCA8K_PORT_LOOKUP_VLAN_MODE(x) FIELD_PREP(QCA8K_PORT_LOOKUP_VLAN_MODE_MASK, x)
|
|
+#define QCA8K_PORT_LOOKUP_VLAN_MODE_NONE QCA8K_PORT_LOOKUP_VLAN_MODE(0x0)
|
|
+#define QCA8K_PORT_LOOKUP_VLAN_MODE_FALLBACK QCA8K_PORT_LOOKUP_VLAN_MODE(0x1)
|
|
+#define QCA8K_PORT_LOOKUP_VLAN_MODE_CHECK QCA8K_PORT_LOOKUP_VLAN_MODE(0x2)
|
|
+#define QCA8K_PORT_LOOKUP_VLAN_MODE_SECURE QCA8K_PORT_LOOKUP_VLAN_MODE(0x3)
|
|
+#define QCA8K_PORT_LOOKUP_STATE_MASK GENMASK(18, 16)
|
|
+#define QCA8K_PORT_LOOKUP_STATE(x) FIELD_PREP(QCA8K_PORT_LOOKUP_STATE_MASK, x)
|
|
+#define QCA8K_PORT_LOOKUP_STATE_DISABLED QCA8K_PORT_LOOKUP_STATE(0x0)
|
|
+#define QCA8K_PORT_LOOKUP_STATE_BLOCKING QCA8K_PORT_LOOKUP_STATE(0x1)
|
|
+#define QCA8K_PORT_LOOKUP_STATE_LISTENING QCA8K_PORT_LOOKUP_STATE(0x2)
|
|
+#define QCA8K_PORT_LOOKUP_STATE_LEARNING QCA8K_PORT_LOOKUP_STATE(0x3)
|
|
+#define QCA8K_PORT_LOOKUP_STATE_FORWARD QCA8K_PORT_LOOKUP_STATE(0x4)
|
|
+#define QCA8K_PORT_LOOKUP_LEARN BIT(20)
|
|
+#define QCA8K_PORT_LOOKUP_ING_MIRROR_EN BIT(25)
|
|
+
|
|
+#define QCA8K_REG_GOL_TRUNK_CTRL0 0x700
|
|
+/* 4 max trunk first
|
|
+ * first 6 bit for member bitmap
|
|
+ * 7th bit is to enable trunk port
|
|
+ */
|
|
+#define QCA8K_REG_GOL_TRUNK_SHIFT(_i) ((_i) * 8)
|
|
+#define QCA8K_REG_GOL_TRUNK_EN_MASK BIT(7)
|
|
+#define QCA8K_REG_GOL_TRUNK_EN(_i) (QCA8K_REG_GOL_TRUNK_EN_MASK << QCA8K_REG_GOL_TRUNK_SHIFT(_i))
|
|
+#define QCA8K_REG_GOL_TRUNK_MEMBER_MASK GENMASK(6, 0)
|
|
+#define QCA8K_REG_GOL_TRUNK_MEMBER(_i) (QCA8K_REG_GOL_TRUNK_MEMBER_MASK << QCA8K_REG_GOL_TRUNK_SHIFT(_i))
|
|
+/* 0x704 for TRUNK 0-1 --- 0x708 for TRUNK 2-3 */
|
|
+#define QCA8K_REG_GOL_TRUNK_CTRL(_i) (0x704 + (((_i) / 2) * 4))
|
|
+#define QCA8K_REG_GOL_TRUNK_ID_MEM_ID_MASK GENMASK(3, 0)
|
|
+#define QCA8K_REG_GOL_TRUNK_ID_MEM_ID_EN_MASK BIT(3)
|
|
+#define QCA8K_REG_GOL_TRUNK_ID_MEM_ID_PORT_MASK GENMASK(2, 0)
|
|
+#define QCA8K_REG_GOL_TRUNK_ID_SHIFT(_i) (((_i) / 2) * 16)
|
|
+#define QCA8K_REG_GOL_MEM_ID_SHIFT(_i) ((_i) * 4)
|
|
+/* Complex shift: FIRST shift for port THEN shift for trunk */
|
|
+#define QCA8K_REG_GOL_TRUNK_ID_MEM_ID_SHIFT(_i, _j) (QCA8K_REG_GOL_MEM_ID_SHIFT(_j) + QCA8K_REG_GOL_TRUNK_ID_SHIFT(_i))
|
|
+#define QCA8K_REG_GOL_TRUNK_ID_MEM_ID_EN(_i, _j) (QCA8K_REG_GOL_TRUNK_ID_MEM_ID_EN_MASK << QCA8K_REG_GOL_TRUNK_ID_MEM_ID_SHIFT(_i, _j))
|
|
+#define QCA8K_REG_GOL_TRUNK_ID_MEM_ID_PORT(_i, _j) (QCA8K_REG_GOL_TRUNK_ID_MEM_ID_PORT_MASK << QCA8K_REG_GOL_TRUNK_ID_MEM_ID_SHIFT(_i, _j))
|
|
+
|
|
+#define QCA8K_REG_GLOBAL_FC_THRESH 0x800
|
|
+#define QCA8K_GLOBAL_FC_GOL_XON_THRES_MASK GENMASK(24, 16)
|
|
+#define QCA8K_GLOBAL_FC_GOL_XON_THRES(x) FIELD_PREP(QCA8K_GLOBAL_FC_GOL_XON_THRES_MASK, x)
|
|
+#define QCA8K_GLOBAL_FC_GOL_XOFF_THRES_MASK GENMASK(8, 0)
|
|
+#define QCA8K_GLOBAL_FC_GOL_XOFF_THRES(x) FIELD_PREP(QCA8K_GLOBAL_FC_GOL_XOFF_THRES_MASK, x)
|
|
+
|
|
+#define QCA8K_REG_PORT_HOL_CTRL0(_i) (0x970 + (_i) * 0x8)
|
|
+#define QCA8K_PORT_HOL_CTRL0_EG_PRI0_BUF_MASK GENMASK(3, 0)
|
|
+#define QCA8K_PORT_HOL_CTRL0_EG_PRI0(x) FIELD_PREP(QCA8K_PORT_HOL_CTRL0_EG_PRI0_BUF_MASK, x)
|
|
+#define QCA8K_PORT_HOL_CTRL0_EG_PRI1_BUF_MASK GENMASK(7, 4)
|
|
+#define QCA8K_PORT_HOL_CTRL0_EG_PRI1(x) FIELD_PREP(QCA8K_PORT_HOL_CTRL0_EG_PRI1_BUF_MASK, x)
|
|
+#define QCA8K_PORT_HOL_CTRL0_EG_PRI2_BUF_MASK GENMASK(11, 8)
|
|
+#define QCA8K_PORT_HOL_CTRL0_EG_PRI2(x) FIELD_PREP(QCA8K_PORT_HOL_CTRL0_EG_PRI2_BUF_MASK, x)
|
|
+#define QCA8K_PORT_HOL_CTRL0_EG_PRI3_BUF_MASK GENMASK(15, 12)
|
|
+#define QCA8K_PORT_HOL_CTRL0_EG_PRI3(x) FIELD_PREP(QCA8K_PORT_HOL_CTRL0_EG_PRI3_BUF_MASK, x)
|
|
+#define QCA8K_PORT_HOL_CTRL0_EG_PRI4_BUF_MASK GENMASK(19, 16)
|
|
+#define QCA8K_PORT_HOL_CTRL0_EG_PRI4(x) FIELD_PREP(QCA8K_PORT_HOL_CTRL0_EG_PRI4_BUF_MASK, x)
|
|
+#define QCA8K_PORT_HOL_CTRL0_EG_PRI5_BUF_MASK GENMASK(23, 20)
|
|
+#define QCA8K_PORT_HOL_CTRL0_EG_PRI5(x) FIELD_PREP(QCA8K_PORT_HOL_CTRL0_EG_PRI5_BUF_MASK, x)
|
|
+#define QCA8K_PORT_HOL_CTRL0_EG_PORT_BUF_MASK GENMASK(29, 24)
|
|
+#define QCA8K_PORT_HOL_CTRL0_EG_PORT(x) FIELD_PREP(QCA8K_PORT_HOL_CTRL0_EG_PORT_BUF_MASK, x)
|
|
+
|
|
+#define QCA8K_REG_PORT_HOL_CTRL1(_i) (0x974 + (_i) * 0x8)
|
|
+#define QCA8K_PORT_HOL_CTRL1_ING_BUF_MASK GENMASK(3, 0)
|
|
+#define QCA8K_PORT_HOL_CTRL1_ING(x) FIELD_PREP(QCA8K_PORT_HOL_CTRL1_ING_BUF_MASK, x)
|
|
+#define QCA8K_PORT_HOL_CTRL1_EG_PRI_BUF_EN BIT(6)
|
|
+#define QCA8K_PORT_HOL_CTRL1_EG_PORT_BUF_EN BIT(7)
|
|
+#define QCA8K_PORT_HOL_CTRL1_WRED_EN BIT(8)
|
|
+#define QCA8K_PORT_HOL_CTRL1_EG_MIRROR_EN BIT(16)
|
|
+
|
|
+/* Pkt edit registers */
|
|
+#define QCA8K_EGREES_VLAN_PORT_SHIFT(_i) (16 * ((_i) % 2))
|
|
+#define QCA8K_EGREES_VLAN_PORT_MASK(_i) (GENMASK(11, 0) << QCA8K_EGREES_VLAN_PORT_SHIFT(_i))
|
|
+#define QCA8K_EGREES_VLAN_PORT(_i, x) ((x) << QCA8K_EGREES_VLAN_PORT_SHIFT(_i))
|
|
+#define QCA8K_EGRESS_VLAN(x) (0x0c70 + (4 * (x / 2)))
|
|
+
|
|
+/* L3 registers */
|
|
+#define QCA8K_HROUTER_CONTROL 0xe00
|
|
+#define QCA8K_HROUTER_CONTROL_GLB_LOCKTIME_M GENMASK(17, 16)
|
|
+#define QCA8K_HROUTER_CONTROL_GLB_LOCKTIME_S 16
|
|
+#define QCA8K_HROUTER_CONTROL_ARP_AGE_MODE 1
|
|
+#define QCA8K_HROUTER_PBASED_CONTROL1 0xe08
|
|
+#define QCA8K_HROUTER_PBASED_CONTROL2 0xe0c
|
|
+#define QCA8K_HNAT_CONTROL 0xe38
|
|
+
|
|
+/* MIB registers */
|
|
+#define QCA8K_PORT_MIB_COUNTER(_i) (0x1000 + (_i) * 0x100)
|
|
+
|
|
+/* QCA specific MII registers */
|
|
+#define MII_ATH_MMD_ADDR 0x0d
|
|
+#define MII_ATH_MMD_DATA 0x0e
|
|
+
|
|
+enum {
|
|
+ QCA8K_PORT_SPEED_10M = 0,
|
|
+ QCA8K_PORT_SPEED_100M = 1,
|
|
+ QCA8K_PORT_SPEED_1000M = 2,
|
|
+ QCA8K_PORT_SPEED_ERR = 3,
|
|
+};
|
|
+
|
|
+enum qca8k_fdb_cmd {
|
|
+ QCA8K_FDB_FLUSH = 1,
|
|
+ QCA8K_FDB_LOAD = 2,
|
|
+ QCA8K_FDB_PURGE = 3,
|
|
+ QCA8K_FDB_FLUSH_PORT = 5,
|
|
+ QCA8K_FDB_NEXT = 6,
|
|
+ QCA8K_FDB_SEARCH = 7,
|
|
+};
|
|
+
|
|
+enum qca8k_vlan_cmd {
|
|
+ QCA8K_VLAN_FLUSH = 1,
|
|
+ QCA8K_VLAN_LOAD = 2,
|
|
+ QCA8K_VLAN_PURGE = 3,
|
|
+ QCA8K_VLAN_REMOVE_PORT = 4,
|
|
+ QCA8K_VLAN_NEXT = 5,
|
|
+ QCA8K_VLAN_READ = 6,
|
|
+};
|
|
+
|
|
+enum qca8k_mid_cmd {
|
|
+ QCA8K_MIB_FLUSH = 1,
|
|
+ QCA8K_MIB_FLUSH_PORT = 2,
|
|
+ QCA8K_MIB_CAST = 3,
|
|
+};
|
|
+
|
|
+struct qca8k_match_data {
|
|
+ u8 id;
|
|
+ bool reduced_package;
|
|
+ u8 mib_count;
|
|
+};
|
|
+
|
|
+enum {
|
|
+ QCA8K_CPU_PORT0,
|
|
+ QCA8K_CPU_PORT6,
|
|
+};
|
|
+
|
|
+struct qca8k_mgmt_eth_data {
|
|
+ struct completion rw_done;
|
|
+ struct mutex mutex; /* Enforce one mdio read/write at time */
|
|
+ bool ack;
|
|
+ u32 seq;
|
|
+ u32 data[4];
|
|
+};
|
|
+
|
|
+struct qca8k_mib_eth_data {
|
|
+ struct completion rw_done;
|
|
+ struct mutex mutex; /* Process one command at time */
|
|
+ refcount_t port_parsed; /* Counter to track parsed port */
|
|
+ u8 req_port;
|
|
+ u64 *data; /* pointer to ethtool data */
|
|
+};
|
|
+
|
|
+struct qca8k_ports_config {
|
|
+ bool sgmii_rx_clk_falling_edge;
|
|
+ bool sgmii_tx_clk_falling_edge;
|
|
+ bool sgmii_enable_pll;
|
|
+ u8 rgmii_rx_delay[QCA8K_NUM_CPU_PORTS]; /* 0: CPU port0, 1: CPU port6 */
|
|
+ u8 rgmii_tx_delay[QCA8K_NUM_CPU_PORTS]; /* 0: CPU port0, 1: CPU port6 */
|
|
+};
|
|
+
|
|
+struct qca8k_mdio_cache {
|
|
+/* The 32bit switch registers are accessed indirectly. To achieve this we need
|
|
+ * to set the page of the register. Track the last page that was set to reduce
|
|
+ * mdio writes
|
|
+ */
|
|
+ u16 page;
|
|
+/* lo and hi can also be cached and from Documentation we can skip one
|
|
+ * extra mdio write if lo or hi is didn't change.
|
|
+ */
|
|
+ u16 lo;
|
|
+ u16 hi;
|
|
+};
|
|
+
|
|
+struct qca8k_priv {
|
|
+ u8 switch_id;
|
|
+ u8 switch_revision;
|
|
+ u8 mirror_rx;
|
|
+ u8 mirror_tx;
|
|
+ u8 lag_hash_mode;
|
|
+ /* Each bit correspond to a port. This switch can support a max of 7 port.
|
|
+ * Bit 1: port enabled. Bit 0: port disabled.
|
|
+ */
|
|
+ u8 port_enabled_map;
|
|
+ struct qca8k_ports_config ports_config;
|
|
+ struct regmap *regmap;
|
|
+ struct mii_bus *bus;
|
|
+ struct dsa_switch *ds;
|
|
+ struct mutex reg_mutex;
|
|
+ struct device *dev;
|
|
+ struct gpio_desc *reset_gpio;
|
|
+ struct net_device *mgmt_master; /* Track if mdio/mib Ethernet is available */
|
|
+ struct qca8k_mgmt_eth_data mgmt_eth_data;
|
|
+ struct qca8k_mib_eth_data mib_eth_data;
|
|
+ struct qca8k_mdio_cache mdio_cache;
|
|
+};
|
|
+
|
|
+struct qca8k_mib_desc {
|
|
+ unsigned int size;
|
|
+ unsigned int offset;
|
|
+ const char *name;
|
|
+};
|
|
+
|
|
+struct qca8k_fdb {
|
|
+ u16 vid;
|
|
+ u8 port_mask;
|
|
+ u8 aging;
|
|
+ u8 mac[6];
|
|
+};
|
|
+
|
|
+#endif /* __QCA8K_H */
|
|
--- a/drivers/net/dsa/qca8k.c
|
|
+++ /dev/null
|
|
@@ -1,3243 +0,0 @@
|
|
-// SPDX-License-Identifier: GPL-2.0
|
|
-/*
|
|
- * Copyright (C) 2009 Felix Fietkau <nbd@nbd.name>
|
|
- * Copyright (C) 2011-2012 Gabor Juhos <juhosg@openwrt.org>
|
|
- * Copyright (c) 2015, 2019, The Linux Foundation. All rights reserved.
|
|
- * Copyright (c) 2016 John Crispin <john@phrozen.org>
|
|
- */
|
|
-
|
|
-#include <linux/module.h>
|
|
-#include <linux/phy.h>
|
|
-#include <linux/netdevice.h>
|
|
-#include <linux/bitfield.h>
|
|
-#include <linux/regmap.h>
|
|
-#include <net/dsa.h>
|
|
-#include <linux/of_net.h>
|
|
-#include <linux/of_mdio.h>
|
|
-#include <linux/of_platform.h>
|
|
-#include <linux/if_bridge.h>
|
|
-#include <linux/mdio.h>
|
|
-#include <linux/phylink.h>
|
|
-#include <linux/gpio/consumer.h>
|
|
-#include <linux/etherdevice.h>
|
|
-#include <linux/dsa/tag_qca.h>
|
|
-
|
|
-#include "qca8k.h"
|
|
-
|
|
-#define MIB_DESC(_s, _o, _n) \
|
|
- { \
|
|
- .size = (_s), \
|
|
- .offset = (_o), \
|
|
- .name = (_n), \
|
|
- }
|
|
-
|
|
-static const struct qca8k_mib_desc ar8327_mib[] = {
|
|
- MIB_DESC(1, 0x00, "RxBroad"),
|
|
- MIB_DESC(1, 0x04, "RxPause"),
|
|
- MIB_DESC(1, 0x08, "RxMulti"),
|
|
- MIB_DESC(1, 0x0c, "RxFcsErr"),
|
|
- MIB_DESC(1, 0x10, "RxAlignErr"),
|
|
- MIB_DESC(1, 0x14, "RxRunt"),
|
|
- MIB_DESC(1, 0x18, "RxFragment"),
|
|
- MIB_DESC(1, 0x1c, "Rx64Byte"),
|
|
- MIB_DESC(1, 0x20, "Rx128Byte"),
|
|
- MIB_DESC(1, 0x24, "Rx256Byte"),
|
|
- MIB_DESC(1, 0x28, "Rx512Byte"),
|
|
- MIB_DESC(1, 0x2c, "Rx1024Byte"),
|
|
- MIB_DESC(1, 0x30, "Rx1518Byte"),
|
|
- MIB_DESC(1, 0x34, "RxMaxByte"),
|
|
- MIB_DESC(1, 0x38, "RxTooLong"),
|
|
- MIB_DESC(2, 0x3c, "RxGoodByte"),
|
|
- MIB_DESC(2, 0x44, "RxBadByte"),
|
|
- MIB_DESC(1, 0x4c, "RxOverFlow"),
|
|
- MIB_DESC(1, 0x50, "Filtered"),
|
|
- MIB_DESC(1, 0x54, "TxBroad"),
|
|
- MIB_DESC(1, 0x58, "TxPause"),
|
|
- MIB_DESC(1, 0x5c, "TxMulti"),
|
|
- MIB_DESC(1, 0x60, "TxUnderRun"),
|
|
- MIB_DESC(1, 0x64, "Tx64Byte"),
|
|
- MIB_DESC(1, 0x68, "Tx128Byte"),
|
|
- MIB_DESC(1, 0x6c, "Tx256Byte"),
|
|
- MIB_DESC(1, 0x70, "Tx512Byte"),
|
|
- MIB_DESC(1, 0x74, "Tx1024Byte"),
|
|
- MIB_DESC(1, 0x78, "Tx1518Byte"),
|
|
- MIB_DESC(1, 0x7c, "TxMaxByte"),
|
|
- MIB_DESC(1, 0x80, "TxOverSize"),
|
|
- MIB_DESC(2, 0x84, "TxByte"),
|
|
- MIB_DESC(1, 0x8c, "TxCollision"),
|
|
- MIB_DESC(1, 0x90, "TxAbortCol"),
|
|
- MIB_DESC(1, 0x94, "TxMultiCol"),
|
|
- MIB_DESC(1, 0x98, "TxSingleCol"),
|
|
- MIB_DESC(1, 0x9c, "TxExcDefer"),
|
|
- MIB_DESC(1, 0xa0, "TxDefer"),
|
|
- MIB_DESC(1, 0xa4, "TxLateCol"),
|
|
- MIB_DESC(1, 0xa8, "RXUnicast"),
|
|
- MIB_DESC(1, 0xac, "TXUnicast"),
|
|
-};
|
|
-
|
|
-static void
|
|
-qca8k_split_addr(u32 regaddr, u16 *r1, u16 *r2, u16 *page)
|
|
-{
|
|
- regaddr >>= 1;
|
|
- *r1 = regaddr & 0x1e;
|
|
-
|
|
- regaddr >>= 5;
|
|
- *r2 = regaddr & 0x7;
|
|
-
|
|
- regaddr >>= 3;
|
|
- *page = regaddr & 0x3ff;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_set_lo(struct qca8k_priv *priv, int phy_id, u32 regnum, u16 lo)
|
|
-{
|
|
- u16 *cached_lo = &priv->mdio_cache.lo;
|
|
- struct mii_bus *bus = priv->bus;
|
|
- int ret;
|
|
-
|
|
- if (lo == *cached_lo)
|
|
- return 0;
|
|
-
|
|
- ret = bus->write(bus, phy_id, regnum, lo);
|
|
- if (ret < 0)
|
|
- dev_err_ratelimited(&bus->dev,
|
|
- "failed to write qca8k 32bit lo register\n");
|
|
-
|
|
- *cached_lo = lo;
|
|
- return 0;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_set_hi(struct qca8k_priv *priv, int phy_id, u32 regnum, u16 hi)
|
|
-{
|
|
- u16 *cached_hi = &priv->mdio_cache.hi;
|
|
- struct mii_bus *bus = priv->bus;
|
|
- int ret;
|
|
-
|
|
- if (hi == *cached_hi)
|
|
- return 0;
|
|
-
|
|
- ret = bus->write(bus, phy_id, regnum, hi);
|
|
- if (ret < 0)
|
|
- dev_err_ratelimited(&bus->dev,
|
|
- "failed to write qca8k 32bit hi register\n");
|
|
-
|
|
- *cached_hi = hi;
|
|
- return 0;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_mii_read32(struct mii_bus *bus, int phy_id, u32 regnum, u32 *val)
|
|
-{
|
|
- int ret;
|
|
-
|
|
- ret = bus->read(bus, phy_id, regnum);
|
|
- if (ret >= 0) {
|
|
- *val = ret;
|
|
- ret = bus->read(bus, phy_id, regnum + 1);
|
|
- *val |= ret << 16;
|
|
- }
|
|
-
|
|
- if (ret < 0) {
|
|
- dev_err_ratelimited(&bus->dev,
|
|
- "failed to read qca8k 32bit register\n");
|
|
- *val = 0;
|
|
- return ret;
|
|
- }
|
|
-
|
|
- return 0;
|
|
-}
|
|
-
|
|
-static void
|
|
-qca8k_mii_write32(struct qca8k_priv *priv, int phy_id, u32 regnum, u32 val)
|
|
-{
|
|
- u16 lo, hi;
|
|
- int ret;
|
|
-
|
|
- lo = val & 0xffff;
|
|
- hi = (u16)(val >> 16);
|
|
-
|
|
- ret = qca8k_set_lo(priv, phy_id, regnum, lo);
|
|
- if (ret >= 0)
|
|
- ret = qca8k_set_hi(priv, phy_id, regnum + 1, hi);
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_set_page(struct qca8k_priv *priv, u16 page)
|
|
-{
|
|
- u16 *cached_page = &priv->mdio_cache.page;
|
|
- struct mii_bus *bus = priv->bus;
|
|
- int ret;
|
|
-
|
|
- if (page == *cached_page)
|
|
- return 0;
|
|
-
|
|
- ret = bus->write(bus, 0x18, 0, page);
|
|
- if (ret < 0) {
|
|
- dev_err_ratelimited(&bus->dev,
|
|
- "failed to set qca8k page\n");
|
|
- return ret;
|
|
- }
|
|
-
|
|
- *cached_page = page;
|
|
- usleep_range(1000, 2000);
|
|
- return 0;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_read(struct qca8k_priv *priv, u32 reg, u32 *val)
|
|
-{
|
|
- return regmap_read(priv->regmap, reg, val);
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_write(struct qca8k_priv *priv, u32 reg, u32 val)
|
|
-{
|
|
- return regmap_write(priv->regmap, reg, val);
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_rmw(struct qca8k_priv *priv, u32 reg, u32 mask, u32 write_val)
|
|
-{
|
|
- return regmap_update_bits(priv->regmap, reg, mask, write_val);
|
|
-}
|
|
-
|
|
-static void qca8k_rw_reg_ack_handler(struct dsa_switch *ds, struct sk_buff *skb)
|
|
-{
|
|
- struct qca8k_mgmt_eth_data *mgmt_eth_data;
|
|
- struct qca8k_priv *priv = ds->priv;
|
|
- struct qca_mgmt_ethhdr *mgmt_ethhdr;
|
|
- u8 len, cmd;
|
|
-
|
|
- mgmt_ethhdr = (struct qca_mgmt_ethhdr *)skb_mac_header(skb);
|
|
- mgmt_eth_data = &priv->mgmt_eth_data;
|
|
-
|
|
- cmd = FIELD_GET(QCA_HDR_MGMT_CMD, mgmt_ethhdr->command);
|
|
- len = FIELD_GET(QCA_HDR_MGMT_LENGTH, mgmt_ethhdr->command);
|
|
-
|
|
- /* Make sure the seq match the requested packet */
|
|
- if (mgmt_ethhdr->seq == mgmt_eth_data->seq)
|
|
- mgmt_eth_data->ack = true;
|
|
-
|
|
- if (cmd == MDIO_READ) {
|
|
- mgmt_eth_data->data[0] = mgmt_ethhdr->mdio_data;
|
|
-
|
|
- /* Get the rest of the 12 byte of data.
|
|
- * The read/write function will extract the requested data.
|
|
- */
|
|
- if (len > QCA_HDR_MGMT_DATA1_LEN)
|
|
- memcpy(mgmt_eth_data->data + 1, skb->data,
|
|
- QCA_HDR_MGMT_DATA2_LEN);
|
|
- }
|
|
-
|
|
- complete(&mgmt_eth_data->rw_done);
|
|
-}
|
|
-
|
|
-static struct sk_buff *qca8k_alloc_mdio_header(enum mdio_cmd cmd, u32 reg, u32 *val,
|
|
- int priority, unsigned int len)
|
|
-{
|
|
- struct qca_mgmt_ethhdr *mgmt_ethhdr;
|
|
- unsigned int real_len;
|
|
- struct sk_buff *skb;
|
|
- u32 *data2;
|
|
- u16 hdr;
|
|
-
|
|
- skb = dev_alloc_skb(QCA_HDR_MGMT_PKT_LEN);
|
|
- if (!skb)
|
|
- return NULL;
|
|
-
|
|
- /* Max value for len reg is 15 (0xf) but the switch actually return 16 byte
|
|
- * Actually for some reason the steps are:
|
|
- * 0: nothing
|
|
- * 1-4: first 4 byte
|
|
- * 5-6: first 12 byte
|
|
- * 7-15: all 16 byte
|
|
- */
|
|
- if (len == 16)
|
|
- real_len = 15;
|
|
- else
|
|
- real_len = len;
|
|
-
|
|
- skb_reset_mac_header(skb);
|
|
- skb_set_network_header(skb, skb->len);
|
|
-
|
|
- mgmt_ethhdr = skb_push(skb, QCA_HDR_MGMT_HEADER_LEN + QCA_HDR_LEN);
|
|
-
|
|
- hdr = FIELD_PREP(QCA_HDR_XMIT_VERSION, QCA_HDR_VERSION);
|
|
- hdr |= FIELD_PREP(QCA_HDR_XMIT_PRIORITY, priority);
|
|
- hdr |= QCA_HDR_XMIT_FROM_CPU;
|
|
- hdr |= FIELD_PREP(QCA_HDR_XMIT_DP_BIT, BIT(0));
|
|
- hdr |= FIELD_PREP(QCA_HDR_XMIT_CONTROL, QCA_HDR_XMIT_TYPE_RW_REG);
|
|
-
|
|
- mgmt_ethhdr->command = FIELD_PREP(QCA_HDR_MGMT_ADDR, reg);
|
|
- mgmt_ethhdr->command |= FIELD_PREP(QCA_HDR_MGMT_LENGTH, real_len);
|
|
- mgmt_ethhdr->command |= FIELD_PREP(QCA_HDR_MGMT_CMD, cmd);
|
|
- mgmt_ethhdr->command |= FIELD_PREP(QCA_HDR_MGMT_CHECK_CODE,
|
|
- QCA_HDR_MGMT_CHECK_CODE_VAL);
|
|
-
|
|
- if (cmd == MDIO_WRITE)
|
|
- mgmt_ethhdr->mdio_data = *val;
|
|
-
|
|
- mgmt_ethhdr->hdr = htons(hdr);
|
|
-
|
|
- data2 = skb_put_zero(skb, QCA_HDR_MGMT_DATA2_LEN + QCA_HDR_MGMT_PADDING_LEN);
|
|
- if (cmd == MDIO_WRITE && len > QCA_HDR_MGMT_DATA1_LEN)
|
|
- memcpy(data2, val + 1, len - QCA_HDR_MGMT_DATA1_LEN);
|
|
-
|
|
- return skb;
|
|
-}
|
|
-
|
|
-static void qca8k_mdio_header_fill_seq_num(struct sk_buff *skb, u32 seq_num)
|
|
-{
|
|
- struct qca_mgmt_ethhdr *mgmt_ethhdr;
|
|
-
|
|
- mgmt_ethhdr = (struct qca_mgmt_ethhdr *)skb->data;
|
|
- mgmt_ethhdr->seq = FIELD_PREP(QCA_HDR_MGMT_SEQ_NUM, seq_num);
|
|
-}
|
|
-
|
|
-static int qca8k_read_eth(struct qca8k_priv *priv, u32 reg, u32 *val, int len)
|
|
-{
|
|
- struct qca8k_mgmt_eth_data *mgmt_eth_data = &priv->mgmt_eth_data;
|
|
- struct sk_buff *skb;
|
|
- bool ack;
|
|
- int ret;
|
|
-
|
|
- skb = qca8k_alloc_mdio_header(MDIO_READ, reg, NULL,
|
|
- QCA8K_ETHERNET_MDIO_PRIORITY, len);
|
|
- if (!skb)
|
|
- return -ENOMEM;
|
|
-
|
|
- mutex_lock(&mgmt_eth_data->mutex);
|
|
-
|
|
- /* Check mgmt_master if is operational */
|
|
- if (!priv->mgmt_master) {
|
|
- kfree_skb(skb);
|
|
- mutex_unlock(&mgmt_eth_data->mutex);
|
|
- return -EINVAL;
|
|
- }
|
|
-
|
|
- skb->dev = priv->mgmt_master;
|
|
-
|
|
- reinit_completion(&mgmt_eth_data->rw_done);
|
|
-
|
|
- /* Increment seq_num and set it in the mdio pkt */
|
|
- mgmt_eth_data->seq++;
|
|
- qca8k_mdio_header_fill_seq_num(skb, mgmt_eth_data->seq);
|
|
- mgmt_eth_data->ack = false;
|
|
-
|
|
- dev_queue_xmit(skb);
|
|
-
|
|
- ret = wait_for_completion_timeout(&mgmt_eth_data->rw_done,
|
|
- msecs_to_jiffies(QCA8K_ETHERNET_TIMEOUT));
|
|
-
|
|
- *val = mgmt_eth_data->data[0];
|
|
- if (len > QCA_HDR_MGMT_DATA1_LEN)
|
|
- memcpy(val + 1, mgmt_eth_data->data + 1, len - QCA_HDR_MGMT_DATA1_LEN);
|
|
-
|
|
- ack = mgmt_eth_data->ack;
|
|
-
|
|
- mutex_unlock(&mgmt_eth_data->mutex);
|
|
-
|
|
- if (ret <= 0)
|
|
- return -ETIMEDOUT;
|
|
-
|
|
- if (!ack)
|
|
- return -EINVAL;
|
|
-
|
|
- return 0;
|
|
-}
|
|
-
|
|
-static int qca8k_write_eth(struct qca8k_priv *priv, u32 reg, u32 *val, int len)
|
|
-{
|
|
- struct qca8k_mgmt_eth_data *mgmt_eth_data = &priv->mgmt_eth_data;
|
|
- struct sk_buff *skb;
|
|
- bool ack;
|
|
- int ret;
|
|
-
|
|
- skb = qca8k_alloc_mdio_header(MDIO_WRITE, reg, val,
|
|
- QCA8K_ETHERNET_MDIO_PRIORITY, len);
|
|
- if (!skb)
|
|
- return -ENOMEM;
|
|
-
|
|
- mutex_lock(&mgmt_eth_data->mutex);
|
|
-
|
|
- /* Check mgmt_master if is operational */
|
|
- if (!priv->mgmt_master) {
|
|
- kfree_skb(skb);
|
|
- mutex_unlock(&mgmt_eth_data->mutex);
|
|
- return -EINVAL;
|
|
- }
|
|
-
|
|
- skb->dev = priv->mgmt_master;
|
|
-
|
|
- reinit_completion(&mgmt_eth_data->rw_done);
|
|
-
|
|
- /* Increment seq_num and set it in the mdio pkt */
|
|
- mgmt_eth_data->seq++;
|
|
- qca8k_mdio_header_fill_seq_num(skb, mgmt_eth_data->seq);
|
|
- mgmt_eth_data->ack = false;
|
|
-
|
|
- dev_queue_xmit(skb);
|
|
-
|
|
- ret = wait_for_completion_timeout(&mgmt_eth_data->rw_done,
|
|
- msecs_to_jiffies(QCA8K_ETHERNET_TIMEOUT));
|
|
-
|
|
- ack = mgmt_eth_data->ack;
|
|
-
|
|
- mutex_unlock(&mgmt_eth_data->mutex);
|
|
-
|
|
- if (ret <= 0)
|
|
- return -ETIMEDOUT;
|
|
-
|
|
- if (!ack)
|
|
- return -EINVAL;
|
|
-
|
|
- return 0;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_regmap_update_bits_eth(struct qca8k_priv *priv, u32 reg, u32 mask, u32 write_val)
|
|
-{
|
|
- u32 val = 0;
|
|
- int ret;
|
|
-
|
|
- ret = qca8k_read_eth(priv, reg, &val, sizeof(val));
|
|
- if (ret)
|
|
- return ret;
|
|
-
|
|
- val &= ~mask;
|
|
- val |= write_val;
|
|
-
|
|
- return qca8k_write_eth(priv, reg, &val, sizeof(val));
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_bulk_read(struct qca8k_priv *priv, u32 reg, u32 *val, int len)
|
|
-{
|
|
- int i, count = len / sizeof(u32), ret;
|
|
-
|
|
- if (priv->mgmt_master && !qca8k_read_eth(priv, reg, val, len))
|
|
- return 0;
|
|
-
|
|
- for (i = 0; i < count; i++) {
|
|
- ret = regmap_read(priv->regmap, reg + (i * 4), val + i);
|
|
- if (ret < 0)
|
|
- return ret;
|
|
- }
|
|
-
|
|
- return 0;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_bulk_write(struct qca8k_priv *priv, u32 reg, u32 *val, int len)
|
|
-{
|
|
- int i, count = len / sizeof(u32), ret;
|
|
- u32 tmp;
|
|
-
|
|
- if (priv->mgmt_master && !qca8k_write_eth(priv, reg, val, len))
|
|
- return 0;
|
|
-
|
|
- for (i = 0; i < count; i++) {
|
|
- tmp = val[i];
|
|
-
|
|
- ret = regmap_write(priv->regmap, reg + (i * 4), tmp);
|
|
- if (ret < 0)
|
|
- return ret;
|
|
- }
|
|
-
|
|
- return 0;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_regmap_read(void *ctx, uint32_t reg, uint32_t *val)
|
|
-{
|
|
- struct qca8k_priv *priv = (struct qca8k_priv *)ctx;
|
|
- struct mii_bus *bus = priv->bus;
|
|
- u16 r1, r2, page;
|
|
- int ret;
|
|
-
|
|
- if (!qca8k_read_eth(priv, reg, val, sizeof(*val)))
|
|
- return 0;
|
|
-
|
|
- qca8k_split_addr(reg, &r1, &r2, &page);
|
|
-
|
|
- mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
|
|
-
|
|
- ret = qca8k_set_page(priv, page);
|
|
- if (ret < 0)
|
|
- goto exit;
|
|
-
|
|
- ret = qca8k_mii_read32(bus, 0x10 | r2, r1, val);
|
|
-
|
|
-exit:
|
|
- mutex_unlock(&bus->mdio_lock);
|
|
- return ret;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_regmap_write(void *ctx, uint32_t reg, uint32_t val)
|
|
-{
|
|
- struct qca8k_priv *priv = (struct qca8k_priv *)ctx;
|
|
- struct mii_bus *bus = priv->bus;
|
|
- u16 r1, r2, page;
|
|
- int ret;
|
|
-
|
|
- if (!qca8k_write_eth(priv, reg, &val, sizeof(val)))
|
|
- return 0;
|
|
-
|
|
- qca8k_split_addr(reg, &r1, &r2, &page);
|
|
-
|
|
- mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
|
|
-
|
|
- ret = qca8k_set_page(priv, page);
|
|
- if (ret < 0)
|
|
- goto exit;
|
|
-
|
|
- qca8k_mii_write32(priv, 0x10 | r2, r1, val);
|
|
-
|
|
-exit:
|
|
- mutex_unlock(&bus->mdio_lock);
|
|
- return ret;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_regmap_update_bits(void *ctx, uint32_t reg, uint32_t mask, uint32_t write_val)
|
|
-{
|
|
- struct qca8k_priv *priv = (struct qca8k_priv *)ctx;
|
|
- struct mii_bus *bus = priv->bus;
|
|
- u16 r1, r2, page;
|
|
- u32 val;
|
|
- int ret;
|
|
-
|
|
- if (!qca8k_regmap_update_bits_eth(priv, reg, mask, write_val))
|
|
- return 0;
|
|
-
|
|
- qca8k_split_addr(reg, &r1, &r2, &page);
|
|
-
|
|
- mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
|
|
-
|
|
- ret = qca8k_set_page(priv, page);
|
|
- if (ret < 0)
|
|
- goto exit;
|
|
-
|
|
- ret = qca8k_mii_read32(bus, 0x10 | r2, r1, &val);
|
|
- if (ret < 0)
|
|
- goto exit;
|
|
-
|
|
- val &= ~mask;
|
|
- val |= write_val;
|
|
- qca8k_mii_write32(priv, 0x10 | r2, r1, val);
|
|
-
|
|
-exit:
|
|
- mutex_unlock(&bus->mdio_lock);
|
|
-
|
|
- return ret;
|
|
-}
|
|
-
|
|
-static const struct regmap_range qca8k_readable_ranges[] = {
|
|
- regmap_reg_range(0x0000, 0x00e4), /* Global control */
|
|
- regmap_reg_range(0x0100, 0x0168), /* EEE control */
|
|
- regmap_reg_range(0x0200, 0x0270), /* Parser control */
|
|
- regmap_reg_range(0x0400, 0x0454), /* ACL */
|
|
- regmap_reg_range(0x0600, 0x0718), /* Lookup */
|
|
- regmap_reg_range(0x0800, 0x0b70), /* QM */
|
|
- regmap_reg_range(0x0c00, 0x0c80), /* PKT */
|
|
- regmap_reg_range(0x0e00, 0x0e98), /* L3 */
|
|
- regmap_reg_range(0x1000, 0x10ac), /* MIB - Port0 */
|
|
- regmap_reg_range(0x1100, 0x11ac), /* MIB - Port1 */
|
|
- regmap_reg_range(0x1200, 0x12ac), /* MIB - Port2 */
|
|
- regmap_reg_range(0x1300, 0x13ac), /* MIB - Port3 */
|
|
- regmap_reg_range(0x1400, 0x14ac), /* MIB - Port4 */
|
|
- regmap_reg_range(0x1500, 0x15ac), /* MIB - Port5 */
|
|
- regmap_reg_range(0x1600, 0x16ac), /* MIB - Port6 */
|
|
-
|
|
-};
|
|
-
|
|
-static const struct regmap_access_table qca8k_readable_table = {
|
|
- .yes_ranges = qca8k_readable_ranges,
|
|
- .n_yes_ranges = ARRAY_SIZE(qca8k_readable_ranges),
|
|
-};
|
|
-
|
|
-static struct regmap_config qca8k_regmap_config = {
|
|
- .reg_bits = 16,
|
|
- .val_bits = 32,
|
|
- .reg_stride = 4,
|
|
- .max_register = 0x16ac, /* end MIB - Port6 range */
|
|
- .reg_read = qca8k_regmap_read,
|
|
- .reg_write = qca8k_regmap_write,
|
|
- .reg_update_bits = qca8k_regmap_update_bits,
|
|
- .rd_table = &qca8k_readable_table,
|
|
- .disable_locking = true, /* Locking is handled by qca8k read/write */
|
|
- .cache_type = REGCACHE_NONE, /* Explicitly disable CACHE */
|
|
-};
|
|
-
|
|
-static int
|
|
-qca8k_busy_wait(struct qca8k_priv *priv, u32 reg, u32 mask)
|
|
-{
|
|
- u32 val;
|
|
-
|
|
- return regmap_read_poll_timeout(priv->regmap, reg, val, !(val & mask), 0,
|
|
- QCA8K_BUSY_WAIT_TIMEOUT * USEC_PER_MSEC);
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_fdb_read(struct qca8k_priv *priv, struct qca8k_fdb *fdb)
|
|
-{
|
|
- u32 reg[3];
|
|
- int ret;
|
|
-
|
|
- /* load the ARL table into an array */
|
|
- ret = qca8k_bulk_read(priv, QCA8K_REG_ATU_DATA0, reg, sizeof(reg));
|
|
- if (ret)
|
|
- return ret;
|
|
-
|
|
- /* vid - 83:72 */
|
|
- fdb->vid = FIELD_GET(QCA8K_ATU_VID_MASK, reg[2]);
|
|
- /* aging - 67:64 */
|
|
- fdb->aging = FIELD_GET(QCA8K_ATU_STATUS_MASK, reg[2]);
|
|
- /* portmask - 54:48 */
|
|
- fdb->port_mask = FIELD_GET(QCA8K_ATU_PORT_MASK, reg[1]);
|
|
- /* mac - 47:0 */
|
|
- fdb->mac[0] = FIELD_GET(QCA8K_ATU_ADDR0_MASK, reg[1]);
|
|
- fdb->mac[1] = FIELD_GET(QCA8K_ATU_ADDR1_MASK, reg[1]);
|
|
- fdb->mac[2] = FIELD_GET(QCA8K_ATU_ADDR2_MASK, reg[0]);
|
|
- fdb->mac[3] = FIELD_GET(QCA8K_ATU_ADDR3_MASK, reg[0]);
|
|
- fdb->mac[4] = FIELD_GET(QCA8K_ATU_ADDR4_MASK, reg[0]);
|
|
- fdb->mac[5] = FIELD_GET(QCA8K_ATU_ADDR5_MASK, reg[0]);
|
|
-
|
|
- return 0;
|
|
-}
|
|
-
|
|
-static void
|
|
-qca8k_fdb_write(struct qca8k_priv *priv, u16 vid, u8 port_mask, const u8 *mac,
|
|
- u8 aging)
|
|
-{
|
|
- u32 reg[3] = { 0 };
|
|
-
|
|
- /* vid - 83:72 */
|
|
- reg[2] = FIELD_PREP(QCA8K_ATU_VID_MASK, vid);
|
|
- /* aging - 67:64 */
|
|
- reg[2] |= FIELD_PREP(QCA8K_ATU_STATUS_MASK, aging);
|
|
- /* portmask - 54:48 */
|
|
- reg[1] = FIELD_PREP(QCA8K_ATU_PORT_MASK, port_mask);
|
|
- /* mac - 47:0 */
|
|
- reg[1] |= FIELD_PREP(QCA8K_ATU_ADDR0_MASK, mac[0]);
|
|
- reg[1] |= FIELD_PREP(QCA8K_ATU_ADDR1_MASK, mac[1]);
|
|
- reg[0] |= FIELD_PREP(QCA8K_ATU_ADDR2_MASK, mac[2]);
|
|
- reg[0] |= FIELD_PREP(QCA8K_ATU_ADDR3_MASK, mac[3]);
|
|
- reg[0] |= FIELD_PREP(QCA8K_ATU_ADDR4_MASK, mac[4]);
|
|
- reg[0] |= FIELD_PREP(QCA8K_ATU_ADDR5_MASK, mac[5]);
|
|
-
|
|
- /* load the array into the ARL table */
|
|
- qca8k_bulk_write(priv, QCA8K_REG_ATU_DATA0, reg, sizeof(reg));
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_fdb_access(struct qca8k_priv *priv, enum qca8k_fdb_cmd cmd, int port)
|
|
-{
|
|
- u32 reg;
|
|
- int ret;
|
|
-
|
|
- /* Set the command and FDB index */
|
|
- reg = QCA8K_ATU_FUNC_BUSY;
|
|
- reg |= cmd;
|
|
- if (port >= 0) {
|
|
- reg |= QCA8K_ATU_FUNC_PORT_EN;
|
|
- reg |= FIELD_PREP(QCA8K_ATU_FUNC_PORT_MASK, port);
|
|
- }
|
|
-
|
|
- /* Write the function register triggering the table access */
|
|
- ret = qca8k_write(priv, QCA8K_REG_ATU_FUNC, reg);
|
|
- if (ret)
|
|
- return ret;
|
|
-
|
|
- /* wait for completion */
|
|
- ret = qca8k_busy_wait(priv, QCA8K_REG_ATU_FUNC, QCA8K_ATU_FUNC_BUSY);
|
|
- if (ret)
|
|
- return ret;
|
|
-
|
|
- /* Check for table full violation when adding an entry */
|
|
- if (cmd == QCA8K_FDB_LOAD) {
|
|
- ret = qca8k_read(priv, QCA8K_REG_ATU_FUNC, ®);
|
|
- if (ret < 0)
|
|
- return ret;
|
|
- if (reg & QCA8K_ATU_FUNC_FULL)
|
|
- return -1;
|
|
- }
|
|
-
|
|
- return 0;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_fdb_next(struct qca8k_priv *priv, struct qca8k_fdb *fdb, int port)
|
|
-{
|
|
- int ret;
|
|
-
|
|
- qca8k_fdb_write(priv, fdb->vid, fdb->port_mask, fdb->mac, fdb->aging);
|
|
- ret = qca8k_fdb_access(priv, QCA8K_FDB_NEXT, port);
|
|
- if (ret < 0)
|
|
- return ret;
|
|
-
|
|
- return qca8k_fdb_read(priv, fdb);
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_fdb_add(struct qca8k_priv *priv, const u8 *mac, u16 port_mask,
|
|
- u16 vid, u8 aging)
|
|
-{
|
|
- int ret;
|
|
-
|
|
- mutex_lock(&priv->reg_mutex);
|
|
- qca8k_fdb_write(priv, vid, port_mask, mac, aging);
|
|
- ret = qca8k_fdb_access(priv, QCA8K_FDB_LOAD, -1);
|
|
- mutex_unlock(&priv->reg_mutex);
|
|
-
|
|
- return ret;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_fdb_del(struct qca8k_priv *priv, const u8 *mac, u16 port_mask, u16 vid)
|
|
-{
|
|
- int ret;
|
|
-
|
|
- mutex_lock(&priv->reg_mutex);
|
|
- qca8k_fdb_write(priv, vid, port_mask, mac, 0);
|
|
- ret = qca8k_fdb_access(priv, QCA8K_FDB_PURGE, -1);
|
|
- mutex_unlock(&priv->reg_mutex);
|
|
-
|
|
- return ret;
|
|
-}
|
|
-
|
|
-static void
|
|
-qca8k_fdb_flush(struct qca8k_priv *priv)
|
|
-{
|
|
- mutex_lock(&priv->reg_mutex);
|
|
- qca8k_fdb_access(priv, QCA8K_FDB_FLUSH, -1);
|
|
- mutex_unlock(&priv->reg_mutex);
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_fdb_search_and_insert(struct qca8k_priv *priv, u8 port_mask,
|
|
- const u8 *mac, u16 vid)
|
|
-{
|
|
- struct qca8k_fdb fdb = { 0 };
|
|
- int ret;
|
|
-
|
|
- mutex_lock(&priv->reg_mutex);
|
|
-
|
|
- qca8k_fdb_write(priv, vid, 0, mac, 0);
|
|
- ret = qca8k_fdb_access(priv, QCA8K_FDB_SEARCH, -1);
|
|
- if (ret < 0)
|
|
- goto exit;
|
|
-
|
|
- ret = qca8k_fdb_read(priv, &fdb);
|
|
- if (ret < 0)
|
|
- goto exit;
|
|
-
|
|
- /* Rule exist. Delete first */
|
|
- if (!fdb.aging) {
|
|
- ret = qca8k_fdb_access(priv, QCA8K_FDB_PURGE, -1);
|
|
- if (ret)
|
|
- goto exit;
|
|
- }
|
|
-
|
|
- /* Add port to fdb portmask */
|
|
- fdb.port_mask |= port_mask;
|
|
-
|
|
- qca8k_fdb_write(priv, vid, fdb.port_mask, mac, fdb.aging);
|
|
- ret = qca8k_fdb_access(priv, QCA8K_FDB_LOAD, -1);
|
|
-
|
|
-exit:
|
|
- mutex_unlock(&priv->reg_mutex);
|
|
- return ret;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_fdb_search_and_del(struct qca8k_priv *priv, u8 port_mask,
|
|
- const u8 *mac, u16 vid)
|
|
-{
|
|
- struct qca8k_fdb fdb = { 0 };
|
|
- int ret;
|
|
-
|
|
- mutex_lock(&priv->reg_mutex);
|
|
-
|
|
- qca8k_fdb_write(priv, vid, 0, mac, 0);
|
|
- ret = qca8k_fdb_access(priv, QCA8K_FDB_SEARCH, -1);
|
|
- if (ret < 0)
|
|
- goto exit;
|
|
-
|
|
- /* Rule doesn't exist. Why delete? */
|
|
- if (!fdb.aging) {
|
|
- ret = -EINVAL;
|
|
- goto exit;
|
|
- }
|
|
-
|
|
- ret = qca8k_fdb_access(priv, QCA8K_FDB_PURGE, -1);
|
|
- if (ret)
|
|
- goto exit;
|
|
-
|
|
- /* Only port in the rule is this port. Don't re insert */
|
|
- if (fdb.port_mask == port_mask)
|
|
- goto exit;
|
|
-
|
|
- /* Remove port from port mask */
|
|
- fdb.port_mask &= ~port_mask;
|
|
-
|
|
- qca8k_fdb_write(priv, vid, fdb.port_mask, mac, fdb.aging);
|
|
- ret = qca8k_fdb_access(priv, QCA8K_FDB_LOAD, -1);
|
|
-
|
|
-exit:
|
|
- mutex_unlock(&priv->reg_mutex);
|
|
- return ret;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_vlan_access(struct qca8k_priv *priv, enum qca8k_vlan_cmd cmd, u16 vid)
|
|
-{
|
|
- u32 reg;
|
|
- int ret;
|
|
-
|
|
- /* Set the command and VLAN index */
|
|
- reg = QCA8K_VTU_FUNC1_BUSY;
|
|
- reg |= cmd;
|
|
- reg |= FIELD_PREP(QCA8K_VTU_FUNC1_VID_MASK, vid);
|
|
-
|
|
- /* Write the function register triggering the table access */
|
|
- ret = qca8k_write(priv, QCA8K_REG_VTU_FUNC1, reg);
|
|
- if (ret)
|
|
- return ret;
|
|
-
|
|
- /* wait for completion */
|
|
- ret = qca8k_busy_wait(priv, QCA8K_REG_VTU_FUNC1, QCA8K_VTU_FUNC1_BUSY);
|
|
- if (ret)
|
|
- return ret;
|
|
-
|
|
- /* Check for table full violation when adding an entry */
|
|
- if (cmd == QCA8K_VLAN_LOAD) {
|
|
- ret = qca8k_read(priv, QCA8K_REG_VTU_FUNC1, ®);
|
|
- if (ret < 0)
|
|
- return ret;
|
|
- if (reg & QCA8K_VTU_FUNC1_FULL)
|
|
- return -ENOMEM;
|
|
- }
|
|
-
|
|
- return 0;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_vlan_add(struct qca8k_priv *priv, u8 port, u16 vid, bool untagged)
|
|
-{
|
|
- u32 reg;
|
|
- int ret;
|
|
-
|
|
- /*
|
|
- We do the right thing with VLAN 0 and treat it as untagged while
|
|
- preserving the tag on egress.
|
|
- */
|
|
- if (vid == 0)
|
|
- return 0;
|
|
-
|
|
- mutex_lock(&priv->reg_mutex);
|
|
- ret = qca8k_vlan_access(priv, QCA8K_VLAN_READ, vid);
|
|
- if (ret < 0)
|
|
- goto out;
|
|
-
|
|
- ret = qca8k_read(priv, QCA8K_REG_VTU_FUNC0, ®);
|
|
- if (ret < 0)
|
|
- goto out;
|
|
- reg |= QCA8K_VTU_FUNC0_VALID | QCA8K_VTU_FUNC0_IVL_EN;
|
|
- reg &= ~QCA8K_VTU_FUNC0_EG_MODE_PORT_MASK(port);
|
|
- if (untagged)
|
|
- reg |= QCA8K_VTU_FUNC0_EG_MODE_PORT_UNTAG(port);
|
|
- else
|
|
- reg |= QCA8K_VTU_FUNC0_EG_MODE_PORT_TAG(port);
|
|
-
|
|
- ret = qca8k_write(priv, QCA8K_REG_VTU_FUNC0, reg);
|
|
- if (ret)
|
|
- goto out;
|
|
- ret = qca8k_vlan_access(priv, QCA8K_VLAN_LOAD, vid);
|
|
-
|
|
-out:
|
|
- mutex_unlock(&priv->reg_mutex);
|
|
-
|
|
- return ret;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_vlan_del(struct qca8k_priv *priv, u8 port, u16 vid)
|
|
-{
|
|
- u32 reg, mask;
|
|
- int ret, i;
|
|
- bool del;
|
|
-
|
|
- mutex_lock(&priv->reg_mutex);
|
|
- ret = qca8k_vlan_access(priv, QCA8K_VLAN_READ, vid);
|
|
- if (ret < 0)
|
|
- goto out;
|
|
-
|
|
- ret = qca8k_read(priv, QCA8K_REG_VTU_FUNC0, ®);
|
|
- if (ret < 0)
|
|
- goto out;
|
|
- reg &= ~QCA8K_VTU_FUNC0_EG_MODE_PORT_MASK(port);
|
|
- reg |= QCA8K_VTU_FUNC0_EG_MODE_PORT_NOT(port);
|
|
-
|
|
- /* Check if we're the last member to be removed */
|
|
- del = true;
|
|
- for (i = 0; i < QCA8K_NUM_PORTS; i++) {
|
|
- mask = QCA8K_VTU_FUNC0_EG_MODE_PORT_NOT(i);
|
|
-
|
|
- if ((reg & mask) != mask) {
|
|
- del = false;
|
|
- break;
|
|
- }
|
|
- }
|
|
-
|
|
- if (del) {
|
|
- ret = qca8k_vlan_access(priv, QCA8K_VLAN_PURGE, vid);
|
|
- } else {
|
|
- ret = qca8k_write(priv, QCA8K_REG_VTU_FUNC0, reg);
|
|
- if (ret)
|
|
- goto out;
|
|
- ret = qca8k_vlan_access(priv, QCA8K_VLAN_LOAD, vid);
|
|
- }
|
|
-
|
|
-out:
|
|
- mutex_unlock(&priv->reg_mutex);
|
|
-
|
|
- return ret;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_mib_init(struct qca8k_priv *priv)
|
|
-{
|
|
- int ret;
|
|
-
|
|
- mutex_lock(&priv->reg_mutex);
|
|
- ret = regmap_update_bits(priv->regmap, QCA8K_REG_MIB,
|
|
- QCA8K_MIB_FUNC | QCA8K_MIB_BUSY,
|
|
- FIELD_PREP(QCA8K_MIB_FUNC, QCA8K_MIB_FLUSH) |
|
|
- QCA8K_MIB_BUSY);
|
|
- if (ret)
|
|
- goto exit;
|
|
-
|
|
- ret = qca8k_busy_wait(priv, QCA8K_REG_MIB, QCA8K_MIB_BUSY);
|
|
- if (ret)
|
|
- goto exit;
|
|
-
|
|
- ret = regmap_set_bits(priv->regmap, QCA8K_REG_MIB, QCA8K_MIB_CPU_KEEP);
|
|
- if (ret)
|
|
- goto exit;
|
|
-
|
|
- ret = qca8k_write(priv, QCA8K_REG_MODULE_EN, QCA8K_MODULE_EN_MIB);
|
|
-
|
|
-exit:
|
|
- mutex_unlock(&priv->reg_mutex);
|
|
- return ret;
|
|
-}
|
|
-
|
|
-static void
|
|
-qca8k_port_set_status(struct qca8k_priv *priv, int port, int enable)
|
|
-{
|
|
- u32 mask = QCA8K_PORT_STATUS_TXMAC | QCA8K_PORT_STATUS_RXMAC;
|
|
-
|
|
- /* Port 0 and 6 have no internal PHY */
|
|
- if (port > 0 && port < 6)
|
|
- mask |= QCA8K_PORT_STATUS_LINK_AUTO;
|
|
-
|
|
- if (enable)
|
|
- regmap_set_bits(priv->regmap, QCA8K_REG_PORT_STATUS(port), mask);
|
|
- else
|
|
- regmap_clear_bits(priv->regmap, QCA8K_REG_PORT_STATUS(port), mask);
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_phy_eth_busy_wait(struct qca8k_mgmt_eth_data *mgmt_eth_data,
|
|
- struct sk_buff *read_skb, u32 *val)
|
|
-{
|
|
- struct sk_buff *skb = skb_copy(read_skb, GFP_KERNEL);
|
|
- bool ack;
|
|
- int ret;
|
|
-
|
|
- reinit_completion(&mgmt_eth_data->rw_done);
|
|
-
|
|
- /* Increment seq_num and set it in the copy pkt */
|
|
- mgmt_eth_data->seq++;
|
|
- qca8k_mdio_header_fill_seq_num(skb, mgmt_eth_data->seq);
|
|
- mgmt_eth_data->ack = false;
|
|
-
|
|
- dev_queue_xmit(skb);
|
|
-
|
|
- ret = wait_for_completion_timeout(&mgmt_eth_data->rw_done,
|
|
- QCA8K_ETHERNET_TIMEOUT);
|
|
-
|
|
- ack = mgmt_eth_data->ack;
|
|
-
|
|
- if (ret <= 0)
|
|
- return -ETIMEDOUT;
|
|
-
|
|
- if (!ack)
|
|
- return -EINVAL;
|
|
-
|
|
- *val = mgmt_eth_data->data[0];
|
|
-
|
|
- return 0;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_phy_eth_command(struct qca8k_priv *priv, bool read, int phy,
|
|
- int regnum, u16 data)
|
|
-{
|
|
- struct sk_buff *write_skb, *clear_skb, *read_skb;
|
|
- struct qca8k_mgmt_eth_data *mgmt_eth_data;
|
|
- u32 write_val, clear_val = 0, val;
|
|
- struct net_device *mgmt_master;
|
|
- int ret, ret1;
|
|
- bool ack;
|
|
-
|
|
- if (regnum >= QCA8K_MDIO_MASTER_MAX_REG)
|
|
- return -EINVAL;
|
|
-
|
|
- mgmt_eth_data = &priv->mgmt_eth_data;
|
|
-
|
|
- write_val = QCA8K_MDIO_MASTER_BUSY | QCA8K_MDIO_MASTER_EN |
|
|
- QCA8K_MDIO_MASTER_PHY_ADDR(phy) |
|
|
- QCA8K_MDIO_MASTER_REG_ADDR(regnum);
|
|
-
|
|
- if (read) {
|
|
- write_val |= QCA8K_MDIO_MASTER_READ;
|
|
- } else {
|
|
- write_val |= QCA8K_MDIO_MASTER_WRITE;
|
|
- write_val |= QCA8K_MDIO_MASTER_DATA(data);
|
|
- }
|
|
-
|
|
- /* Prealloc all the needed skb before the lock */
|
|
- write_skb = qca8k_alloc_mdio_header(MDIO_WRITE, QCA8K_MDIO_MASTER_CTRL, &write_val,
|
|
- QCA8K_ETHERNET_PHY_PRIORITY, sizeof(write_val));
|
|
- if (!write_skb)
|
|
- return -ENOMEM;
|
|
-
|
|
- clear_skb = qca8k_alloc_mdio_header(MDIO_WRITE, QCA8K_MDIO_MASTER_CTRL, &clear_val,
|
|
- QCA8K_ETHERNET_PHY_PRIORITY, sizeof(clear_val));
|
|
- if (!clear_skb) {
|
|
- ret = -ENOMEM;
|
|
- goto err_clear_skb;
|
|
- }
|
|
-
|
|
- read_skb = qca8k_alloc_mdio_header(MDIO_READ, QCA8K_MDIO_MASTER_CTRL, &clear_val,
|
|
- QCA8K_ETHERNET_PHY_PRIORITY, sizeof(clear_val));
|
|
- if (!read_skb) {
|
|
- ret = -ENOMEM;
|
|
- goto err_read_skb;
|
|
- }
|
|
-
|
|
- /* Actually start the request:
|
|
- * 1. Send mdio master packet
|
|
- * 2. Busy Wait for mdio master command
|
|
- * 3. Get the data if we are reading
|
|
- * 4. Reset the mdio master (even with error)
|
|
- */
|
|
- mutex_lock(&mgmt_eth_data->mutex);
|
|
-
|
|
- /* Check if mgmt_master is operational */
|
|
- mgmt_master = priv->mgmt_master;
|
|
- if (!mgmt_master) {
|
|
- mutex_unlock(&mgmt_eth_data->mutex);
|
|
- ret = -EINVAL;
|
|
- goto err_mgmt_master;
|
|
- }
|
|
-
|
|
- read_skb->dev = mgmt_master;
|
|
- clear_skb->dev = mgmt_master;
|
|
- write_skb->dev = mgmt_master;
|
|
-
|
|
- reinit_completion(&mgmt_eth_data->rw_done);
|
|
-
|
|
- /* Increment seq_num and set it in the write pkt */
|
|
- mgmt_eth_data->seq++;
|
|
- qca8k_mdio_header_fill_seq_num(write_skb, mgmt_eth_data->seq);
|
|
- mgmt_eth_data->ack = false;
|
|
-
|
|
- dev_queue_xmit(write_skb);
|
|
-
|
|
- ret = wait_for_completion_timeout(&mgmt_eth_data->rw_done,
|
|
- QCA8K_ETHERNET_TIMEOUT);
|
|
-
|
|
- ack = mgmt_eth_data->ack;
|
|
-
|
|
- if (ret <= 0) {
|
|
- ret = -ETIMEDOUT;
|
|
- kfree_skb(read_skb);
|
|
- goto exit;
|
|
- }
|
|
-
|
|
- if (!ack) {
|
|
- ret = -EINVAL;
|
|
- kfree_skb(read_skb);
|
|
- goto exit;
|
|
- }
|
|
-
|
|
- ret = read_poll_timeout(qca8k_phy_eth_busy_wait, ret1,
|
|
- !(val & QCA8K_MDIO_MASTER_BUSY), 0,
|
|
- QCA8K_BUSY_WAIT_TIMEOUT * USEC_PER_MSEC, false,
|
|
- mgmt_eth_data, read_skb, &val);
|
|
-
|
|
- if (ret < 0 && ret1 < 0) {
|
|
- ret = ret1;
|
|
- goto exit;
|
|
- }
|
|
-
|
|
- if (read) {
|
|
- reinit_completion(&mgmt_eth_data->rw_done);
|
|
-
|
|
- /* Increment seq_num and set it in the read pkt */
|
|
- mgmt_eth_data->seq++;
|
|
- qca8k_mdio_header_fill_seq_num(read_skb, mgmt_eth_data->seq);
|
|
- mgmt_eth_data->ack = false;
|
|
-
|
|
- dev_queue_xmit(read_skb);
|
|
-
|
|
- ret = wait_for_completion_timeout(&mgmt_eth_data->rw_done,
|
|
- QCA8K_ETHERNET_TIMEOUT);
|
|
-
|
|
- ack = mgmt_eth_data->ack;
|
|
-
|
|
- if (ret <= 0) {
|
|
- ret = -ETIMEDOUT;
|
|
- goto exit;
|
|
- }
|
|
-
|
|
- if (!ack) {
|
|
- ret = -EINVAL;
|
|
- goto exit;
|
|
- }
|
|
-
|
|
- ret = mgmt_eth_data->data[0] & QCA8K_MDIO_MASTER_DATA_MASK;
|
|
- } else {
|
|
- kfree_skb(read_skb);
|
|
- }
|
|
-exit:
|
|
- reinit_completion(&mgmt_eth_data->rw_done);
|
|
-
|
|
- /* Increment seq_num and set it in the clear pkt */
|
|
- mgmt_eth_data->seq++;
|
|
- qca8k_mdio_header_fill_seq_num(clear_skb, mgmt_eth_data->seq);
|
|
- mgmt_eth_data->ack = false;
|
|
-
|
|
- dev_queue_xmit(clear_skb);
|
|
-
|
|
- wait_for_completion_timeout(&mgmt_eth_data->rw_done,
|
|
- QCA8K_ETHERNET_TIMEOUT);
|
|
-
|
|
- mutex_unlock(&mgmt_eth_data->mutex);
|
|
-
|
|
- return ret;
|
|
-
|
|
- /* Error handling before lock */
|
|
-err_mgmt_master:
|
|
- kfree_skb(read_skb);
|
|
-err_read_skb:
|
|
- kfree_skb(clear_skb);
|
|
-err_clear_skb:
|
|
- kfree_skb(write_skb);
|
|
-
|
|
- return ret;
|
|
-}
|
|
-
|
|
-static u32
|
|
-qca8k_port_to_phy(int port)
|
|
-{
|
|
- /* From Andrew Lunn:
|
|
- * Port 0 has no internal phy.
|
|
- * Port 1 has an internal PHY at MDIO address 0.
|
|
- * Port 2 has an internal PHY at MDIO address 1.
|
|
- * ...
|
|
- * Port 5 has an internal PHY at MDIO address 4.
|
|
- * Port 6 has no internal PHY.
|
|
- */
|
|
-
|
|
- return port - 1;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_mdio_busy_wait(struct mii_bus *bus, u32 reg, u32 mask)
|
|
-{
|
|
- u16 r1, r2, page;
|
|
- u32 val;
|
|
- int ret, ret1;
|
|
-
|
|
- qca8k_split_addr(reg, &r1, &r2, &page);
|
|
-
|
|
- ret = read_poll_timeout(qca8k_mii_read32, ret1, !(val & mask), 0,
|
|
- QCA8K_BUSY_WAIT_TIMEOUT * USEC_PER_MSEC, false,
|
|
- bus, 0x10 | r2, r1, &val);
|
|
-
|
|
- /* Check if qca8k_read has failed for a different reason
|
|
- * before returnting -ETIMEDOUT
|
|
- */
|
|
- if (ret < 0 && ret1 < 0)
|
|
- return ret1;
|
|
-
|
|
- return ret;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_mdio_write(struct qca8k_priv *priv, int phy, int regnum, u16 data)
|
|
-{
|
|
- struct mii_bus *bus = priv->bus;
|
|
- u16 r1, r2, page;
|
|
- u32 val;
|
|
- int ret;
|
|
-
|
|
- if (regnum >= QCA8K_MDIO_MASTER_MAX_REG)
|
|
- return -EINVAL;
|
|
-
|
|
- val = QCA8K_MDIO_MASTER_BUSY | QCA8K_MDIO_MASTER_EN |
|
|
- QCA8K_MDIO_MASTER_WRITE | QCA8K_MDIO_MASTER_PHY_ADDR(phy) |
|
|
- QCA8K_MDIO_MASTER_REG_ADDR(regnum) |
|
|
- QCA8K_MDIO_MASTER_DATA(data);
|
|
-
|
|
- qca8k_split_addr(QCA8K_MDIO_MASTER_CTRL, &r1, &r2, &page);
|
|
-
|
|
- mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
|
|
-
|
|
- ret = qca8k_set_page(priv, page);
|
|
- if (ret)
|
|
- goto exit;
|
|
-
|
|
- qca8k_mii_write32(priv, 0x10 | r2, r1, val);
|
|
-
|
|
- ret = qca8k_mdio_busy_wait(bus, QCA8K_MDIO_MASTER_CTRL,
|
|
- QCA8K_MDIO_MASTER_BUSY);
|
|
-
|
|
-exit:
|
|
- /* even if the busy_wait timeouts try to clear the MASTER_EN */
|
|
- qca8k_mii_write32(priv, 0x10 | r2, r1, 0);
|
|
-
|
|
- mutex_unlock(&bus->mdio_lock);
|
|
-
|
|
- return ret;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_mdio_read(struct qca8k_priv *priv, int phy, int regnum)
|
|
-{
|
|
- struct mii_bus *bus = priv->bus;
|
|
- u16 r1, r2, page;
|
|
- u32 val;
|
|
- int ret;
|
|
-
|
|
- if (regnum >= QCA8K_MDIO_MASTER_MAX_REG)
|
|
- return -EINVAL;
|
|
-
|
|
- val = QCA8K_MDIO_MASTER_BUSY | QCA8K_MDIO_MASTER_EN |
|
|
- QCA8K_MDIO_MASTER_READ | QCA8K_MDIO_MASTER_PHY_ADDR(phy) |
|
|
- QCA8K_MDIO_MASTER_REG_ADDR(regnum);
|
|
-
|
|
- qca8k_split_addr(QCA8K_MDIO_MASTER_CTRL, &r1, &r2, &page);
|
|
-
|
|
- mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
|
|
-
|
|
- ret = qca8k_set_page(priv, page);
|
|
- if (ret)
|
|
- goto exit;
|
|
-
|
|
- qca8k_mii_write32(priv, 0x10 | r2, r1, val);
|
|
-
|
|
- ret = qca8k_mdio_busy_wait(bus, QCA8K_MDIO_MASTER_CTRL,
|
|
- QCA8K_MDIO_MASTER_BUSY);
|
|
- if (ret)
|
|
- goto exit;
|
|
-
|
|
- ret = qca8k_mii_read32(bus, 0x10 | r2, r1, &val);
|
|
-
|
|
-exit:
|
|
- /* even if the busy_wait timeouts try to clear the MASTER_EN */
|
|
- qca8k_mii_write32(priv, 0x10 | r2, r1, 0);
|
|
-
|
|
- mutex_unlock(&bus->mdio_lock);
|
|
-
|
|
- if (ret >= 0)
|
|
- ret = val & QCA8K_MDIO_MASTER_DATA_MASK;
|
|
-
|
|
- return ret;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_internal_mdio_write(struct mii_bus *slave_bus, int phy, int regnum, u16 data)
|
|
-{
|
|
- struct qca8k_priv *priv = slave_bus->priv;
|
|
- int ret;
|
|
-
|
|
- /* Use mdio Ethernet when available, fallback to legacy one on error */
|
|
- ret = qca8k_phy_eth_command(priv, false, phy, regnum, data);
|
|
- if (!ret)
|
|
- return 0;
|
|
-
|
|
- return qca8k_mdio_write(priv, phy, regnum, data);
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_internal_mdio_read(struct mii_bus *slave_bus, int phy, int regnum)
|
|
-{
|
|
- struct qca8k_priv *priv = slave_bus->priv;
|
|
- int ret;
|
|
-
|
|
- /* Use mdio Ethernet when available, fallback to legacy one on error */
|
|
- ret = qca8k_phy_eth_command(priv, true, phy, regnum, 0);
|
|
- if (ret >= 0)
|
|
- return ret;
|
|
-
|
|
- ret = qca8k_mdio_read(priv, phy, regnum);
|
|
-
|
|
- if (ret < 0)
|
|
- return 0xffff;
|
|
-
|
|
- return ret;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_legacy_mdio_write(struct mii_bus *slave_bus, int port, int regnum, u16 data)
|
|
-{
|
|
- port = qca8k_port_to_phy(port) % PHY_MAX_ADDR;
|
|
-
|
|
- return qca8k_internal_mdio_write(slave_bus, port, regnum, data);
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_legacy_mdio_read(struct mii_bus *slave_bus, int port, int regnum)
|
|
-{
|
|
- port = qca8k_port_to_phy(port) % PHY_MAX_ADDR;
|
|
-
|
|
- return qca8k_internal_mdio_read(slave_bus, port, regnum);
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_mdio_register(struct qca8k_priv *priv)
|
|
-{
|
|
- struct dsa_switch *ds = priv->ds;
|
|
- struct device_node *mdio;
|
|
- struct mii_bus *bus;
|
|
-
|
|
- bus = devm_mdiobus_alloc(ds->dev);
|
|
- if (!bus)
|
|
- return -ENOMEM;
|
|
-
|
|
- bus->priv = (void *)priv;
|
|
- snprintf(bus->id, MII_BUS_ID_SIZE, "qca8k-%d.%d",
|
|
- ds->dst->index, ds->index);
|
|
- bus->parent = ds->dev;
|
|
- bus->phy_mask = ~ds->phys_mii_mask;
|
|
- ds->slave_mii_bus = bus;
|
|
-
|
|
- /* Check if the devicetree declare the port:phy mapping */
|
|
- mdio = of_get_child_by_name(priv->dev->of_node, "mdio");
|
|
- if (of_device_is_available(mdio)) {
|
|
- bus->name = "qca8k slave mii";
|
|
- bus->read = qca8k_internal_mdio_read;
|
|
- bus->write = qca8k_internal_mdio_write;
|
|
- return devm_of_mdiobus_register(priv->dev, bus, mdio);
|
|
- }
|
|
-
|
|
- /* If a mapping can't be found the legacy mapping is used,
|
|
- * using the qca8k_port_to_phy function
|
|
- */
|
|
- bus->name = "qca8k-legacy slave mii";
|
|
- bus->read = qca8k_legacy_mdio_read;
|
|
- bus->write = qca8k_legacy_mdio_write;
|
|
- return devm_mdiobus_register(priv->dev, bus);
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_setup_mdio_bus(struct qca8k_priv *priv)
|
|
-{
|
|
- u32 internal_mdio_mask = 0, external_mdio_mask = 0, reg;
|
|
- struct device_node *ports, *port;
|
|
- phy_interface_t mode;
|
|
- int err;
|
|
-
|
|
- ports = of_get_child_by_name(priv->dev->of_node, "ports");
|
|
- if (!ports)
|
|
- ports = of_get_child_by_name(priv->dev->of_node, "ethernet-ports");
|
|
-
|
|
- if (!ports)
|
|
- return -EINVAL;
|
|
-
|
|
- for_each_available_child_of_node(ports, port) {
|
|
- err = of_property_read_u32(port, "reg", ®);
|
|
- if (err) {
|
|
- of_node_put(port);
|
|
- of_node_put(ports);
|
|
- return err;
|
|
- }
|
|
-
|
|
- if (!dsa_is_user_port(priv->ds, reg))
|
|
- continue;
|
|
-
|
|
- of_get_phy_mode(port, &mode);
|
|
-
|
|
- if (of_property_read_bool(port, "phy-handle") &&
|
|
- mode != PHY_INTERFACE_MODE_INTERNAL)
|
|
- external_mdio_mask |= BIT(reg);
|
|
- else
|
|
- internal_mdio_mask |= BIT(reg);
|
|
- }
|
|
-
|
|
- of_node_put(ports);
|
|
- if (!external_mdio_mask && !internal_mdio_mask) {
|
|
- dev_err(priv->dev, "no PHYs are defined.\n");
|
|
- return -EINVAL;
|
|
- }
|
|
-
|
|
- /* The QCA8K_MDIO_MASTER_EN Bit, which grants access to PHYs through
|
|
- * the MDIO_MASTER register also _disconnects_ the external MDC
|
|
- * passthrough to the internal PHYs. It's not possible to use both
|
|
- * configurations at the same time!
|
|
- *
|
|
- * Because this came up during the review process:
|
|
- * If the external mdio-bus driver is capable magically disabling
|
|
- * the QCA8K_MDIO_MASTER_EN and mutex/spin-locking out the qca8k's
|
|
- * accessors for the time being, it would be possible to pull this
|
|
- * off.
|
|
- */
|
|
- if (!!external_mdio_mask && !!internal_mdio_mask) {
|
|
- dev_err(priv->dev, "either internal or external mdio bus configuration is supported.\n");
|
|
- return -EINVAL;
|
|
- }
|
|
-
|
|
- if (external_mdio_mask) {
|
|
- /* Make sure to disable the internal mdio bus in cases
|
|
- * a dt-overlay and driver reload changed the configuration
|
|
- */
|
|
-
|
|
- return regmap_clear_bits(priv->regmap, QCA8K_MDIO_MASTER_CTRL,
|
|
- QCA8K_MDIO_MASTER_EN);
|
|
- }
|
|
-
|
|
- return qca8k_mdio_register(priv);
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_setup_mac_pwr_sel(struct qca8k_priv *priv)
|
|
-{
|
|
- u32 mask = 0;
|
|
- int ret = 0;
|
|
-
|
|
- /* SoC specific settings for ipq8064.
|
|
- * If more device require this consider adding
|
|
- * a dedicated binding.
|
|
- */
|
|
- if (of_machine_is_compatible("qcom,ipq8064"))
|
|
- mask |= QCA8K_MAC_PWR_RGMII0_1_8V;
|
|
-
|
|
- /* SoC specific settings for ipq8065 */
|
|
- if (of_machine_is_compatible("qcom,ipq8065"))
|
|
- mask |= QCA8K_MAC_PWR_RGMII1_1_8V;
|
|
-
|
|
- if (mask) {
|
|
- ret = qca8k_rmw(priv, QCA8K_REG_MAC_PWR_SEL,
|
|
- QCA8K_MAC_PWR_RGMII0_1_8V |
|
|
- QCA8K_MAC_PWR_RGMII1_1_8V,
|
|
- mask);
|
|
- }
|
|
-
|
|
- return ret;
|
|
-}
|
|
-
|
|
-static int qca8k_find_cpu_port(struct dsa_switch *ds)
|
|
-{
|
|
- struct qca8k_priv *priv = ds->priv;
|
|
-
|
|
- /* Find the connected cpu port. Valid port are 0 or 6 */
|
|
- if (dsa_is_cpu_port(ds, 0))
|
|
- return 0;
|
|
-
|
|
- dev_dbg(priv->dev, "port 0 is not the CPU port. Checking port 6");
|
|
-
|
|
- if (dsa_is_cpu_port(ds, 6))
|
|
- return 6;
|
|
-
|
|
- return -EINVAL;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_setup_of_pws_reg(struct qca8k_priv *priv)
|
|
-{
|
|
- struct device_node *node = priv->dev->of_node;
|
|
- const struct qca8k_match_data *data;
|
|
- u32 val = 0;
|
|
- int ret;
|
|
-
|
|
- /* QCA8327 require to set to the correct mode.
|
|
- * His bigger brother QCA8328 have the 172 pin layout.
|
|
- * Should be applied by default but we set this just to make sure.
|
|
- */
|
|
- if (priv->switch_id == QCA8K_ID_QCA8327) {
|
|
- data = of_device_get_match_data(priv->dev);
|
|
-
|
|
- /* Set the correct package of 148 pin for QCA8327 */
|
|
- if (data->reduced_package)
|
|
- val |= QCA8327_PWS_PACKAGE148_EN;
|
|
-
|
|
- ret = qca8k_rmw(priv, QCA8K_REG_PWS, QCA8327_PWS_PACKAGE148_EN,
|
|
- val);
|
|
- if (ret)
|
|
- return ret;
|
|
- }
|
|
-
|
|
- if (of_property_read_bool(node, "qca,ignore-power-on-sel"))
|
|
- val |= QCA8K_PWS_POWER_ON_SEL;
|
|
-
|
|
- if (of_property_read_bool(node, "qca,led-open-drain")) {
|
|
- if (!(val & QCA8K_PWS_POWER_ON_SEL)) {
|
|
- dev_err(priv->dev, "qca,led-open-drain require qca,ignore-power-on-sel to be set.");
|
|
- return -EINVAL;
|
|
- }
|
|
-
|
|
- val |= QCA8K_PWS_LED_OPEN_EN_CSR;
|
|
- }
|
|
-
|
|
- return qca8k_rmw(priv, QCA8K_REG_PWS,
|
|
- QCA8K_PWS_LED_OPEN_EN_CSR | QCA8K_PWS_POWER_ON_SEL,
|
|
- val);
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_parse_port_config(struct qca8k_priv *priv)
|
|
-{
|
|
- int port, cpu_port_index = -1, ret;
|
|
- struct device_node *port_dn;
|
|
- phy_interface_t mode;
|
|
- struct dsa_port *dp;
|
|
- u32 delay;
|
|
-
|
|
- /* We have 2 CPU port. Check them */
|
|
- for (port = 0; port < QCA8K_NUM_PORTS; port++) {
|
|
- /* Skip every other port */
|
|
- if (port != 0 && port != 6)
|
|
- continue;
|
|
-
|
|
- dp = dsa_to_port(priv->ds, port);
|
|
- port_dn = dp->dn;
|
|
- cpu_port_index++;
|
|
-
|
|
- if (!of_device_is_available(port_dn))
|
|
- continue;
|
|
-
|
|
- ret = of_get_phy_mode(port_dn, &mode);
|
|
- if (ret)
|
|
- continue;
|
|
-
|
|
- switch (mode) {
|
|
- case PHY_INTERFACE_MODE_RGMII:
|
|
- case PHY_INTERFACE_MODE_RGMII_ID:
|
|
- case PHY_INTERFACE_MODE_RGMII_TXID:
|
|
- case PHY_INTERFACE_MODE_RGMII_RXID:
|
|
- case PHY_INTERFACE_MODE_SGMII:
|
|
- delay = 0;
|
|
-
|
|
- if (!of_property_read_u32(port_dn, "tx-internal-delay-ps", &delay))
|
|
- /* Switch regs accept value in ns, convert ps to ns */
|
|
- delay = delay / 1000;
|
|
- else if (mode == PHY_INTERFACE_MODE_RGMII_ID ||
|
|
- mode == PHY_INTERFACE_MODE_RGMII_TXID)
|
|
- delay = 1;
|
|
-
|
|
- if (!FIELD_FIT(QCA8K_PORT_PAD_RGMII_TX_DELAY_MASK, delay)) {
|
|
- dev_err(priv->dev, "rgmii tx delay is limited to a max value of 3ns, setting to the max value");
|
|
- delay = 3;
|
|
- }
|
|
-
|
|
- priv->ports_config.rgmii_tx_delay[cpu_port_index] = delay;
|
|
-
|
|
- delay = 0;
|
|
-
|
|
- if (!of_property_read_u32(port_dn, "rx-internal-delay-ps", &delay))
|
|
- /* Switch regs accept value in ns, convert ps to ns */
|
|
- delay = delay / 1000;
|
|
- else if (mode == PHY_INTERFACE_MODE_RGMII_ID ||
|
|
- mode == PHY_INTERFACE_MODE_RGMII_RXID)
|
|
- delay = 2;
|
|
-
|
|
- if (!FIELD_FIT(QCA8K_PORT_PAD_RGMII_RX_DELAY_MASK, delay)) {
|
|
- dev_err(priv->dev, "rgmii rx delay is limited to a max value of 3ns, setting to the max value");
|
|
- delay = 3;
|
|
- }
|
|
-
|
|
- priv->ports_config.rgmii_rx_delay[cpu_port_index] = delay;
|
|
-
|
|
- /* Skip sgmii parsing for rgmii* mode */
|
|
- if (mode == PHY_INTERFACE_MODE_RGMII ||
|
|
- mode == PHY_INTERFACE_MODE_RGMII_ID ||
|
|
- mode == PHY_INTERFACE_MODE_RGMII_TXID ||
|
|
- mode == PHY_INTERFACE_MODE_RGMII_RXID)
|
|
- break;
|
|
-
|
|
- if (of_property_read_bool(port_dn, "qca,sgmii-txclk-falling-edge"))
|
|
- priv->ports_config.sgmii_tx_clk_falling_edge = true;
|
|
-
|
|
- if (of_property_read_bool(port_dn, "qca,sgmii-rxclk-falling-edge"))
|
|
- priv->ports_config.sgmii_rx_clk_falling_edge = true;
|
|
-
|
|
- if (of_property_read_bool(port_dn, "qca,sgmii-enable-pll")) {
|
|
- priv->ports_config.sgmii_enable_pll = true;
|
|
-
|
|
- if (priv->switch_id == QCA8K_ID_QCA8327) {
|
|
- dev_err(priv->dev, "SGMII PLL should NOT be enabled for qca8327. Aborting enabling");
|
|
- priv->ports_config.sgmii_enable_pll = false;
|
|
- }
|
|
-
|
|
- if (priv->switch_revision < 2)
|
|
- dev_warn(priv->dev, "SGMII PLL should NOT be enabled for qca8337 with revision 2 or more.");
|
|
- }
|
|
-
|
|
- break;
|
|
- default:
|
|
- continue;
|
|
- }
|
|
- }
|
|
-
|
|
- return 0;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_setup(struct dsa_switch *ds)
|
|
-{
|
|
- struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
|
|
- int cpu_port, ret, i;
|
|
- u32 mask;
|
|
-
|
|
- cpu_port = qca8k_find_cpu_port(ds);
|
|
- if (cpu_port < 0) {
|
|
- dev_err(priv->dev, "No cpu port configured in both cpu port0 and port6");
|
|
- return cpu_port;
|
|
- }
|
|
-
|
|
- /* Parse CPU port config to be later used in phy_link mac_config */
|
|
- ret = qca8k_parse_port_config(priv);
|
|
- if (ret)
|
|
- return ret;
|
|
-
|
|
- ret = qca8k_setup_mdio_bus(priv);
|
|
- if (ret)
|
|
- return ret;
|
|
-
|
|
- ret = qca8k_setup_of_pws_reg(priv);
|
|
- if (ret)
|
|
- return ret;
|
|
-
|
|
- ret = qca8k_setup_mac_pwr_sel(priv);
|
|
- if (ret)
|
|
- return ret;
|
|
-
|
|
- /* Make sure MAC06 is disabled */
|
|
- ret = regmap_clear_bits(priv->regmap, QCA8K_REG_PORT0_PAD_CTRL,
|
|
- QCA8K_PORT0_PAD_MAC06_EXCHANGE_EN);
|
|
- if (ret) {
|
|
- dev_err(priv->dev, "failed disabling MAC06 exchange");
|
|
- return ret;
|
|
- }
|
|
-
|
|
- /* Enable CPU Port */
|
|
- ret = regmap_set_bits(priv->regmap, QCA8K_REG_GLOBAL_FW_CTRL0,
|
|
- QCA8K_GLOBAL_FW_CTRL0_CPU_PORT_EN);
|
|
- if (ret) {
|
|
- dev_err(priv->dev, "failed enabling CPU port");
|
|
- return ret;
|
|
- }
|
|
-
|
|
- /* Enable MIB counters */
|
|
- ret = qca8k_mib_init(priv);
|
|
- if (ret)
|
|
- dev_warn(priv->dev, "mib init failed");
|
|
-
|
|
- /* Initial setup of all ports */
|
|
- for (i = 0; i < QCA8K_NUM_PORTS; i++) {
|
|
- /* Disable forwarding by default on all ports */
|
|
- ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i),
|
|
- QCA8K_PORT_LOOKUP_MEMBER, 0);
|
|
- if (ret)
|
|
- return ret;
|
|
-
|
|
- /* Enable QCA header mode on all cpu ports */
|
|
- if (dsa_is_cpu_port(ds, i)) {
|
|
- ret = qca8k_write(priv, QCA8K_REG_PORT_HDR_CTRL(i),
|
|
- FIELD_PREP(QCA8K_PORT_HDR_CTRL_TX_MASK, QCA8K_PORT_HDR_CTRL_ALL) |
|
|
- FIELD_PREP(QCA8K_PORT_HDR_CTRL_RX_MASK, QCA8K_PORT_HDR_CTRL_ALL));
|
|
- if (ret) {
|
|
- dev_err(priv->dev, "failed enabling QCA header mode");
|
|
- return ret;
|
|
- }
|
|
- }
|
|
-
|
|
- /* Disable MAC by default on all user ports */
|
|
- if (dsa_is_user_port(ds, i))
|
|
- qca8k_port_set_status(priv, i, 0);
|
|
- }
|
|
-
|
|
- /* Forward all unknown frames to CPU port for Linux processing
|
|
- * Notice that in multi-cpu config only one port should be set
|
|
- * for igmp, unknown, multicast and broadcast packet
|
|
- */
|
|
- ret = qca8k_write(priv, QCA8K_REG_GLOBAL_FW_CTRL1,
|
|
- FIELD_PREP(QCA8K_GLOBAL_FW_CTRL1_IGMP_DP_MASK, BIT(cpu_port)) |
|
|
- FIELD_PREP(QCA8K_GLOBAL_FW_CTRL1_BC_DP_MASK, BIT(cpu_port)) |
|
|
- FIELD_PREP(QCA8K_GLOBAL_FW_CTRL1_MC_DP_MASK, BIT(cpu_port)) |
|
|
- FIELD_PREP(QCA8K_GLOBAL_FW_CTRL1_UC_DP_MASK, BIT(cpu_port)));
|
|
- if (ret)
|
|
- return ret;
|
|
-
|
|
- /* Setup connection between CPU port & user ports
|
|
- * Configure specific switch configuration for ports
|
|
- */
|
|
- for (i = 0; i < QCA8K_NUM_PORTS; i++) {
|
|
- /* CPU port gets connected to all user ports of the switch */
|
|
- if (dsa_is_cpu_port(ds, i)) {
|
|
- ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i),
|
|
- QCA8K_PORT_LOOKUP_MEMBER, dsa_user_ports(ds));
|
|
- if (ret)
|
|
- return ret;
|
|
- }
|
|
-
|
|
- /* Individual user ports get connected to CPU port only */
|
|
- if (dsa_is_user_port(ds, i)) {
|
|
- ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i),
|
|
- QCA8K_PORT_LOOKUP_MEMBER,
|
|
- BIT(cpu_port));
|
|
- if (ret)
|
|
- return ret;
|
|
-
|
|
- /* Enable ARP Auto-learning by default */
|
|
- ret = regmap_set_bits(priv->regmap, QCA8K_PORT_LOOKUP_CTRL(i),
|
|
- QCA8K_PORT_LOOKUP_LEARN);
|
|
- if (ret)
|
|
- return ret;
|
|
-
|
|
- /* For port based vlans to work we need to set the
|
|
- * default egress vid
|
|
- */
|
|
- ret = qca8k_rmw(priv, QCA8K_EGRESS_VLAN(i),
|
|
- QCA8K_EGREES_VLAN_PORT_MASK(i),
|
|
- QCA8K_EGREES_VLAN_PORT(i, QCA8K_PORT_VID_DEF));
|
|
- if (ret)
|
|
- return ret;
|
|
-
|
|
- ret = qca8k_write(priv, QCA8K_REG_PORT_VLAN_CTRL0(i),
|
|
- QCA8K_PORT_VLAN_CVID(QCA8K_PORT_VID_DEF) |
|
|
- QCA8K_PORT_VLAN_SVID(QCA8K_PORT_VID_DEF));
|
|
- if (ret)
|
|
- return ret;
|
|
- }
|
|
-
|
|
- /* The port 5 of the qca8337 have some problem in flood condition. The
|
|
- * original legacy driver had some specific buffer and priority settings
|
|
- * for the different port suggested by the QCA switch team. Add this
|
|
- * missing settings to improve switch stability under load condition.
|
|
- * This problem is limited to qca8337 and other qca8k switch are not affected.
|
|
- */
|
|
- if (priv->switch_id == QCA8K_ID_QCA8337) {
|
|
- switch (i) {
|
|
- /* The 2 CPU port and port 5 requires some different
|
|
- * priority than any other ports.
|
|
- */
|
|
- case 0:
|
|
- case 5:
|
|
- case 6:
|
|
- mask = QCA8K_PORT_HOL_CTRL0_EG_PRI0(0x3) |
|
|
- QCA8K_PORT_HOL_CTRL0_EG_PRI1(0x4) |
|
|
- QCA8K_PORT_HOL_CTRL0_EG_PRI2(0x4) |
|
|
- QCA8K_PORT_HOL_CTRL0_EG_PRI3(0x4) |
|
|
- QCA8K_PORT_HOL_CTRL0_EG_PRI4(0x6) |
|
|
- QCA8K_PORT_HOL_CTRL0_EG_PRI5(0x8) |
|
|
- QCA8K_PORT_HOL_CTRL0_EG_PORT(0x1e);
|
|
- break;
|
|
- default:
|
|
- mask = QCA8K_PORT_HOL_CTRL0_EG_PRI0(0x3) |
|
|
- QCA8K_PORT_HOL_CTRL0_EG_PRI1(0x4) |
|
|
- QCA8K_PORT_HOL_CTRL0_EG_PRI2(0x6) |
|
|
- QCA8K_PORT_HOL_CTRL0_EG_PRI3(0x8) |
|
|
- QCA8K_PORT_HOL_CTRL0_EG_PORT(0x19);
|
|
- }
|
|
- qca8k_write(priv, QCA8K_REG_PORT_HOL_CTRL0(i), mask);
|
|
-
|
|
- mask = QCA8K_PORT_HOL_CTRL1_ING(0x6) |
|
|
- QCA8K_PORT_HOL_CTRL1_EG_PRI_BUF_EN |
|
|
- QCA8K_PORT_HOL_CTRL1_EG_PORT_BUF_EN |
|
|
- QCA8K_PORT_HOL_CTRL1_WRED_EN;
|
|
- qca8k_rmw(priv, QCA8K_REG_PORT_HOL_CTRL1(i),
|
|
- QCA8K_PORT_HOL_CTRL1_ING_BUF_MASK |
|
|
- QCA8K_PORT_HOL_CTRL1_EG_PRI_BUF_EN |
|
|
- QCA8K_PORT_HOL_CTRL1_EG_PORT_BUF_EN |
|
|
- QCA8K_PORT_HOL_CTRL1_WRED_EN,
|
|
- mask);
|
|
- }
|
|
- }
|
|
-
|
|
- /* Special GLOBAL_FC_THRESH value are needed for ar8327 switch */
|
|
- if (priv->switch_id == QCA8K_ID_QCA8327) {
|
|
- mask = QCA8K_GLOBAL_FC_GOL_XON_THRES(288) |
|
|
- QCA8K_GLOBAL_FC_GOL_XOFF_THRES(496);
|
|
- qca8k_rmw(priv, QCA8K_REG_GLOBAL_FC_THRESH,
|
|
- QCA8K_GLOBAL_FC_GOL_XON_THRES_MASK |
|
|
- QCA8K_GLOBAL_FC_GOL_XOFF_THRES_MASK,
|
|
- mask);
|
|
- }
|
|
-
|
|
- /* Setup our port MTUs to match power on defaults */
|
|
- ret = qca8k_write(priv, QCA8K_MAX_FRAME_SIZE, ETH_FRAME_LEN + ETH_FCS_LEN);
|
|
- if (ret)
|
|
- dev_warn(priv->dev, "failed setting MTU settings");
|
|
-
|
|
- /* Flush the FDB table */
|
|
- qca8k_fdb_flush(priv);
|
|
-
|
|
- /* We don't have interrupts for link changes, so we need to poll */
|
|
- ds->pcs_poll = true;
|
|
-
|
|
- /* Set min a max ageing value supported */
|
|
- ds->ageing_time_min = 7000;
|
|
- ds->ageing_time_max = 458745000;
|
|
-
|
|
- /* Set max number of LAGs supported */
|
|
- ds->num_lag_ids = QCA8K_NUM_LAGS;
|
|
-
|
|
- return 0;
|
|
-}
|
|
-
|
|
-static void
|
|
-qca8k_mac_config_setup_internal_delay(struct qca8k_priv *priv, int cpu_port_index,
|
|
- u32 reg)
|
|
-{
|
|
- u32 delay, val = 0;
|
|
- int ret;
|
|
-
|
|
- /* Delay can be declared in 3 different way.
|
|
- * Mode to rgmii and internal-delay standard binding defined
|
|
- * rgmii-id or rgmii-tx/rx phy mode set.
|
|
- * The parse logic set a delay different than 0 only when one
|
|
- * of the 3 different way is used. In all other case delay is
|
|
- * not enabled. With ID or TX/RXID delay is enabled and set
|
|
- * to the default and recommended value.
|
|
- */
|
|
- if (priv->ports_config.rgmii_tx_delay[cpu_port_index]) {
|
|
- delay = priv->ports_config.rgmii_tx_delay[cpu_port_index];
|
|
-
|
|
- val |= QCA8K_PORT_PAD_RGMII_TX_DELAY(delay) |
|
|
- QCA8K_PORT_PAD_RGMII_TX_DELAY_EN;
|
|
- }
|
|
-
|
|
- if (priv->ports_config.rgmii_rx_delay[cpu_port_index]) {
|
|
- delay = priv->ports_config.rgmii_rx_delay[cpu_port_index];
|
|
-
|
|
- val |= QCA8K_PORT_PAD_RGMII_RX_DELAY(delay) |
|
|
- QCA8K_PORT_PAD_RGMII_RX_DELAY_EN;
|
|
- }
|
|
-
|
|
- /* Set RGMII delay based on the selected values */
|
|
- ret = qca8k_rmw(priv, reg,
|
|
- QCA8K_PORT_PAD_RGMII_TX_DELAY_MASK |
|
|
- QCA8K_PORT_PAD_RGMII_RX_DELAY_MASK |
|
|
- QCA8K_PORT_PAD_RGMII_TX_DELAY_EN |
|
|
- QCA8K_PORT_PAD_RGMII_RX_DELAY_EN,
|
|
- val);
|
|
- if (ret)
|
|
- dev_err(priv->dev, "Failed to set internal delay for CPU port%d",
|
|
- cpu_port_index == QCA8K_CPU_PORT0 ? 0 : 6);
|
|
-}
|
|
-
|
|
-static void
|
|
-qca8k_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
|
|
- const struct phylink_link_state *state)
|
|
-{
|
|
- struct qca8k_priv *priv = ds->priv;
|
|
- int cpu_port_index, ret;
|
|
- u32 reg, val;
|
|
-
|
|
- switch (port) {
|
|
- case 0: /* 1st CPU port */
|
|
- if (state->interface != PHY_INTERFACE_MODE_RGMII &&
|
|
- state->interface != PHY_INTERFACE_MODE_RGMII_ID &&
|
|
- state->interface != PHY_INTERFACE_MODE_RGMII_TXID &&
|
|
- state->interface != PHY_INTERFACE_MODE_RGMII_RXID &&
|
|
- state->interface != PHY_INTERFACE_MODE_SGMII)
|
|
- return;
|
|
-
|
|
- reg = QCA8K_REG_PORT0_PAD_CTRL;
|
|
- cpu_port_index = QCA8K_CPU_PORT0;
|
|
- break;
|
|
- case 1:
|
|
- case 2:
|
|
- case 3:
|
|
- case 4:
|
|
- case 5:
|
|
- /* Internal PHY, nothing to do */
|
|
- return;
|
|
- case 6: /* 2nd CPU port / external PHY */
|
|
- if (state->interface != PHY_INTERFACE_MODE_RGMII &&
|
|
- state->interface != PHY_INTERFACE_MODE_RGMII_ID &&
|
|
- state->interface != PHY_INTERFACE_MODE_RGMII_TXID &&
|
|
- state->interface != PHY_INTERFACE_MODE_RGMII_RXID &&
|
|
- state->interface != PHY_INTERFACE_MODE_SGMII &&
|
|
- state->interface != PHY_INTERFACE_MODE_1000BASEX)
|
|
- return;
|
|
-
|
|
- reg = QCA8K_REG_PORT6_PAD_CTRL;
|
|
- cpu_port_index = QCA8K_CPU_PORT6;
|
|
- break;
|
|
- default:
|
|
- dev_err(ds->dev, "%s: unsupported port: %i\n", __func__, port);
|
|
- return;
|
|
- }
|
|
-
|
|
- if (port != 6 && phylink_autoneg_inband(mode)) {
|
|
- dev_err(ds->dev, "%s: in-band negotiation unsupported\n",
|
|
- __func__);
|
|
- return;
|
|
- }
|
|
-
|
|
- switch (state->interface) {
|
|
- case PHY_INTERFACE_MODE_RGMII:
|
|
- case PHY_INTERFACE_MODE_RGMII_ID:
|
|
- case PHY_INTERFACE_MODE_RGMII_TXID:
|
|
- case PHY_INTERFACE_MODE_RGMII_RXID:
|
|
- qca8k_write(priv, reg, QCA8K_PORT_PAD_RGMII_EN);
|
|
-
|
|
- /* Configure rgmii delay */
|
|
- qca8k_mac_config_setup_internal_delay(priv, cpu_port_index, reg);
|
|
-
|
|
- /* QCA8337 requires to set rgmii rx delay for all ports.
|
|
- * This is enabled through PORT5_PAD_CTRL for all ports,
|
|
- * rather than individual port registers.
|
|
- */
|
|
- if (priv->switch_id == QCA8K_ID_QCA8337)
|
|
- qca8k_write(priv, QCA8K_REG_PORT5_PAD_CTRL,
|
|
- QCA8K_PORT_PAD_RGMII_RX_DELAY_EN);
|
|
- break;
|
|
- case PHY_INTERFACE_MODE_SGMII:
|
|
- case PHY_INTERFACE_MODE_1000BASEX:
|
|
- /* Enable SGMII on the port */
|
|
- qca8k_write(priv, reg, QCA8K_PORT_PAD_SGMII_EN);
|
|
-
|
|
- /* Enable/disable SerDes auto-negotiation as necessary */
|
|
- ret = qca8k_read(priv, QCA8K_REG_PWS, &val);
|
|
- if (ret)
|
|
- return;
|
|
- if (phylink_autoneg_inband(mode))
|
|
- val &= ~QCA8K_PWS_SERDES_AEN_DIS;
|
|
- else
|
|
- val |= QCA8K_PWS_SERDES_AEN_DIS;
|
|
- qca8k_write(priv, QCA8K_REG_PWS, val);
|
|
-
|
|
- /* Configure the SGMII parameters */
|
|
- ret = qca8k_read(priv, QCA8K_REG_SGMII_CTRL, &val);
|
|
- if (ret)
|
|
- return;
|
|
-
|
|
- val |= QCA8K_SGMII_EN_SD;
|
|
-
|
|
- if (priv->ports_config.sgmii_enable_pll)
|
|
- val |= QCA8K_SGMII_EN_PLL | QCA8K_SGMII_EN_RX |
|
|
- QCA8K_SGMII_EN_TX;
|
|
-
|
|
- if (dsa_is_cpu_port(ds, port)) {
|
|
- /* CPU port, we're talking to the CPU MAC, be a PHY */
|
|
- val &= ~QCA8K_SGMII_MODE_CTRL_MASK;
|
|
- val |= QCA8K_SGMII_MODE_CTRL_PHY;
|
|
- } else if (state->interface == PHY_INTERFACE_MODE_SGMII) {
|
|
- val &= ~QCA8K_SGMII_MODE_CTRL_MASK;
|
|
- val |= QCA8K_SGMII_MODE_CTRL_MAC;
|
|
- } else if (state->interface == PHY_INTERFACE_MODE_1000BASEX) {
|
|
- val &= ~QCA8K_SGMII_MODE_CTRL_MASK;
|
|
- val |= QCA8K_SGMII_MODE_CTRL_BASEX;
|
|
- }
|
|
-
|
|
- qca8k_write(priv, QCA8K_REG_SGMII_CTRL, val);
|
|
-
|
|
- /* From original code is reported port instability as SGMII also
|
|
- * require delay set. Apply advised values here or take them from DT.
|
|
- */
|
|
- if (state->interface == PHY_INTERFACE_MODE_SGMII)
|
|
- qca8k_mac_config_setup_internal_delay(priv, cpu_port_index, reg);
|
|
-
|
|
- /* For qca8327/qca8328/qca8334/qca8338 sgmii is unique and
|
|
- * falling edge is set writing in the PORT0 PAD reg
|
|
- */
|
|
- if (priv->switch_id == QCA8K_ID_QCA8327 ||
|
|
- priv->switch_id == QCA8K_ID_QCA8337)
|
|
- reg = QCA8K_REG_PORT0_PAD_CTRL;
|
|
-
|
|
- val = 0;
|
|
-
|
|
- /* SGMII Clock phase configuration */
|
|
- if (priv->ports_config.sgmii_rx_clk_falling_edge)
|
|
- val |= QCA8K_PORT0_PAD_SGMII_RXCLK_FALLING_EDGE;
|
|
-
|
|
- if (priv->ports_config.sgmii_tx_clk_falling_edge)
|
|
- val |= QCA8K_PORT0_PAD_SGMII_TXCLK_FALLING_EDGE;
|
|
-
|
|
- if (val)
|
|
- ret = qca8k_rmw(priv, reg,
|
|
- QCA8K_PORT0_PAD_SGMII_RXCLK_FALLING_EDGE |
|
|
- QCA8K_PORT0_PAD_SGMII_TXCLK_FALLING_EDGE,
|
|
- val);
|
|
-
|
|
- break;
|
|
- default:
|
|
- dev_err(ds->dev, "xMII mode %s not supported for port %d\n",
|
|
- phy_modes(state->interface), port);
|
|
- return;
|
|
- }
|
|
-}
|
|
-
|
|
-static void
|
|
-qca8k_phylink_validate(struct dsa_switch *ds, int port,
|
|
- unsigned long *supported,
|
|
- struct phylink_link_state *state)
|
|
-{
|
|
- __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
|
|
-
|
|
- switch (port) {
|
|
- case 0: /* 1st CPU port */
|
|
- if (state->interface != PHY_INTERFACE_MODE_NA &&
|
|
- state->interface != PHY_INTERFACE_MODE_RGMII &&
|
|
- state->interface != PHY_INTERFACE_MODE_RGMII_ID &&
|
|
- state->interface != PHY_INTERFACE_MODE_RGMII_TXID &&
|
|
- state->interface != PHY_INTERFACE_MODE_RGMII_RXID &&
|
|
- state->interface != PHY_INTERFACE_MODE_SGMII)
|
|
- goto unsupported;
|
|
- break;
|
|
- case 1:
|
|
- case 2:
|
|
- case 3:
|
|
- case 4:
|
|
- case 5:
|
|
- /* Internal PHY */
|
|
- if (state->interface != PHY_INTERFACE_MODE_NA &&
|
|
- state->interface != PHY_INTERFACE_MODE_GMII &&
|
|
- state->interface != PHY_INTERFACE_MODE_INTERNAL)
|
|
- goto unsupported;
|
|
- break;
|
|
- case 6: /* 2nd CPU port / external PHY */
|
|
- if (state->interface != PHY_INTERFACE_MODE_NA &&
|
|
- state->interface != PHY_INTERFACE_MODE_RGMII &&
|
|
- state->interface != PHY_INTERFACE_MODE_RGMII_ID &&
|
|
- state->interface != PHY_INTERFACE_MODE_RGMII_TXID &&
|
|
- state->interface != PHY_INTERFACE_MODE_RGMII_RXID &&
|
|
- state->interface != PHY_INTERFACE_MODE_SGMII &&
|
|
- state->interface != PHY_INTERFACE_MODE_1000BASEX)
|
|
- goto unsupported;
|
|
- break;
|
|
- default:
|
|
-unsupported:
|
|
- linkmode_zero(supported);
|
|
- return;
|
|
- }
|
|
-
|
|
- phylink_set_port_modes(mask);
|
|
- phylink_set(mask, Autoneg);
|
|
-
|
|
- phylink_set(mask, 1000baseT_Full);
|
|
- phylink_set(mask, 10baseT_Half);
|
|
- phylink_set(mask, 10baseT_Full);
|
|
- phylink_set(mask, 100baseT_Half);
|
|
- phylink_set(mask, 100baseT_Full);
|
|
-
|
|
- if (state->interface == PHY_INTERFACE_MODE_1000BASEX)
|
|
- phylink_set(mask, 1000baseX_Full);
|
|
-
|
|
- phylink_set(mask, Pause);
|
|
- phylink_set(mask, Asym_Pause);
|
|
-
|
|
- linkmode_and(supported, supported, mask);
|
|
- linkmode_and(state->advertising, state->advertising, mask);
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_phylink_mac_link_state(struct dsa_switch *ds, int port,
|
|
- struct phylink_link_state *state)
|
|
-{
|
|
- struct qca8k_priv *priv = ds->priv;
|
|
- u32 reg;
|
|
- int ret;
|
|
-
|
|
- ret = qca8k_read(priv, QCA8K_REG_PORT_STATUS(port), ®);
|
|
- if (ret < 0)
|
|
- return ret;
|
|
-
|
|
- state->link = !!(reg & QCA8K_PORT_STATUS_LINK_UP);
|
|
- state->an_complete = state->link;
|
|
- state->an_enabled = !!(reg & QCA8K_PORT_STATUS_LINK_AUTO);
|
|
- state->duplex = (reg & QCA8K_PORT_STATUS_DUPLEX) ? DUPLEX_FULL :
|
|
- DUPLEX_HALF;
|
|
-
|
|
- switch (reg & QCA8K_PORT_STATUS_SPEED) {
|
|
- case QCA8K_PORT_STATUS_SPEED_10:
|
|
- state->speed = SPEED_10;
|
|
- break;
|
|
- case QCA8K_PORT_STATUS_SPEED_100:
|
|
- state->speed = SPEED_100;
|
|
- break;
|
|
- case QCA8K_PORT_STATUS_SPEED_1000:
|
|
- state->speed = SPEED_1000;
|
|
- break;
|
|
- default:
|
|
- state->speed = SPEED_UNKNOWN;
|
|
- break;
|
|
- }
|
|
-
|
|
- state->pause = MLO_PAUSE_NONE;
|
|
- if (reg & QCA8K_PORT_STATUS_RXFLOW)
|
|
- state->pause |= MLO_PAUSE_RX;
|
|
- if (reg & QCA8K_PORT_STATUS_TXFLOW)
|
|
- state->pause |= MLO_PAUSE_TX;
|
|
-
|
|
- return 1;
|
|
-}
|
|
-
|
|
-static void
|
|
-qca8k_phylink_mac_link_down(struct dsa_switch *ds, int port, unsigned int mode,
|
|
- phy_interface_t interface)
|
|
-{
|
|
- struct qca8k_priv *priv = ds->priv;
|
|
-
|
|
- qca8k_port_set_status(priv, port, 0);
|
|
-}
|
|
-
|
|
-static void
|
|
-qca8k_phylink_mac_link_up(struct dsa_switch *ds, int port, unsigned int mode,
|
|
- phy_interface_t interface, struct phy_device *phydev,
|
|
- int speed, int duplex, bool tx_pause, bool rx_pause)
|
|
-{
|
|
- struct qca8k_priv *priv = ds->priv;
|
|
- u32 reg;
|
|
-
|
|
- if (phylink_autoneg_inband(mode)) {
|
|
- reg = QCA8K_PORT_STATUS_LINK_AUTO;
|
|
- } else {
|
|
- switch (speed) {
|
|
- case SPEED_10:
|
|
- reg = QCA8K_PORT_STATUS_SPEED_10;
|
|
- break;
|
|
- case SPEED_100:
|
|
- reg = QCA8K_PORT_STATUS_SPEED_100;
|
|
- break;
|
|
- case SPEED_1000:
|
|
- reg = QCA8K_PORT_STATUS_SPEED_1000;
|
|
- break;
|
|
- default:
|
|
- reg = QCA8K_PORT_STATUS_LINK_AUTO;
|
|
- break;
|
|
- }
|
|
-
|
|
- if (duplex == DUPLEX_FULL)
|
|
- reg |= QCA8K_PORT_STATUS_DUPLEX;
|
|
-
|
|
- if (rx_pause || dsa_is_cpu_port(ds, port))
|
|
- reg |= QCA8K_PORT_STATUS_RXFLOW;
|
|
-
|
|
- if (tx_pause || dsa_is_cpu_port(ds, port))
|
|
- reg |= QCA8K_PORT_STATUS_TXFLOW;
|
|
- }
|
|
-
|
|
- reg |= QCA8K_PORT_STATUS_TXMAC | QCA8K_PORT_STATUS_RXMAC;
|
|
-
|
|
- qca8k_write(priv, QCA8K_REG_PORT_STATUS(port), reg);
|
|
-}
|
|
-
|
|
-static void
|
|
-qca8k_get_strings(struct dsa_switch *ds, int port, u32 stringset, uint8_t *data)
|
|
-{
|
|
- const struct qca8k_match_data *match_data;
|
|
- struct qca8k_priv *priv = ds->priv;
|
|
- int i;
|
|
-
|
|
- if (stringset != ETH_SS_STATS)
|
|
- return;
|
|
-
|
|
- match_data = of_device_get_match_data(priv->dev);
|
|
-
|
|
- for (i = 0; i < match_data->mib_count; i++)
|
|
- strncpy(data + i * ETH_GSTRING_LEN, ar8327_mib[i].name,
|
|
- ETH_GSTRING_LEN);
|
|
-}
|
|
-
|
|
-static void qca8k_mib_autocast_handler(struct dsa_switch *ds, struct sk_buff *skb)
|
|
-{
|
|
- const struct qca8k_match_data *match_data;
|
|
- struct qca8k_mib_eth_data *mib_eth_data;
|
|
- struct qca8k_priv *priv = ds->priv;
|
|
- const struct qca8k_mib_desc *mib;
|
|
- struct mib_ethhdr *mib_ethhdr;
|
|
- int i, mib_len, offset = 0;
|
|
- u64 *data;
|
|
- u8 port;
|
|
-
|
|
- mib_ethhdr = (struct mib_ethhdr *)skb_mac_header(skb);
|
|
- mib_eth_data = &priv->mib_eth_data;
|
|
-
|
|
- /* The switch autocast every port. Ignore other packet and
|
|
- * parse only the requested one.
|
|
- */
|
|
- port = FIELD_GET(QCA_HDR_RECV_SOURCE_PORT, ntohs(mib_ethhdr->hdr));
|
|
- if (port != mib_eth_data->req_port)
|
|
- goto exit;
|
|
-
|
|
- match_data = device_get_match_data(priv->dev);
|
|
- data = mib_eth_data->data;
|
|
-
|
|
- for (i = 0; i < match_data->mib_count; i++) {
|
|
- mib = &ar8327_mib[i];
|
|
-
|
|
- /* First 3 mib are present in the skb head */
|
|
- if (i < 3) {
|
|
- data[i] = mib_ethhdr->data[i];
|
|
- continue;
|
|
- }
|
|
-
|
|
- mib_len = sizeof(uint32_t);
|
|
-
|
|
- /* Some mib are 64 bit wide */
|
|
- if (mib->size == 2)
|
|
- mib_len = sizeof(uint64_t);
|
|
-
|
|
- /* Copy the mib value from packet to the */
|
|
- memcpy(data + i, skb->data + offset, mib_len);
|
|
-
|
|
- /* Set the offset for the next mib */
|
|
- offset += mib_len;
|
|
- }
|
|
-
|
|
-exit:
|
|
- /* Complete on receiving all the mib packet */
|
|
- if (refcount_dec_and_test(&mib_eth_data->port_parsed))
|
|
- complete(&mib_eth_data->rw_done);
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_get_ethtool_stats_eth(struct dsa_switch *ds, int port, u64 *data)
|
|
-{
|
|
- struct dsa_port *dp = dsa_to_port(ds, port);
|
|
- struct qca8k_mib_eth_data *mib_eth_data;
|
|
- struct qca8k_priv *priv = ds->priv;
|
|
- int ret;
|
|
-
|
|
- mib_eth_data = &priv->mib_eth_data;
|
|
-
|
|
- mutex_lock(&mib_eth_data->mutex);
|
|
-
|
|
- reinit_completion(&mib_eth_data->rw_done);
|
|
-
|
|
- mib_eth_data->req_port = dp->index;
|
|
- mib_eth_data->data = data;
|
|
- refcount_set(&mib_eth_data->port_parsed, QCA8K_NUM_PORTS);
|
|
-
|
|
- mutex_lock(&priv->reg_mutex);
|
|
-
|
|
- /* Send mib autocast request */
|
|
- ret = regmap_update_bits(priv->regmap, QCA8K_REG_MIB,
|
|
- QCA8K_MIB_FUNC | QCA8K_MIB_BUSY,
|
|
- FIELD_PREP(QCA8K_MIB_FUNC, QCA8K_MIB_CAST) |
|
|
- QCA8K_MIB_BUSY);
|
|
-
|
|
- mutex_unlock(&priv->reg_mutex);
|
|
-
|
|
- if (ret)
|
|
- goto exit;
|
|
-
|
|
- ret = wait_for_completion_timeout(&mib_eth_data->rw_done, QCA8K_ETHERNET_TIMEOUT);
|
|
-
|
|
-exit:
|
|
- mutex_unlock(&mib_eth_data->mutex);
|
|
-
|
|
- return ret;
|
|
-}
|
|
-
|
|
-static void
|
|
-qca8k_get_ethtool_stats(struct dsa_switch *ds, int port,
|
|
- uint64_t *data)
|
|
-{
|
|
- struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
|
|
- const struct qca8k_match_data *match_data;
|
|
- const struct qca8k_mib_desc *mib;
|
|
- u32 reg, i, val;
|
|
- u32 hi = 0;
|
|
- int ret;
|
|
-
|
|
- if (priv->mgmt_master &&
|
|
- qca8k_get_ethtool_stats_eth(ds, port, data) > 0)
|
|
- return;
|
|
-
|
|
- match_data = of_device_get_match_data(priv->dev);
|
|
-
|
|
- for (i = 0; i < match_data->mib_count; i++) {
|
|
- mib = &ar8327_mib[i];
|
|
- reg = QCA8K_PORT_MIB_COUNTER(port) + mib->offset;
|
|
-
|
|
- ret = qca8k_read(priv, reg, &val);
|
|
- if (ret < 0)
|
|
- continue;
|
|
-
|
|
- if (mib->size == 2) {
|
|
- ret = qca8k_read(priv, reg + 4, &hi);
|
|
- if (ret < 0)
|
|
- continue;
|
|
- }
|
|
-
|
|
- data[i] = val;
|
|
- if (mib->size == 2)
|
|
- data[i] |= (u64)hi << 32;
|
|
- }
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_get_sset_count(struct dsa_switch *ds, int port, int sset)
|
|
-{
|
|
- const struct qca8k_match_data *match_data;
|
|
- struct qca8k_priv *priv = ds->priv;
|
|
-
|
|
- if (sset != ETH_SS_STATS)
|
|
- return 0;
|
|
-
|
|
- match_data = of_device_get_match_data(priv->dev);
|
|
-
|
|
- return match_data->mib_count;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_set_mac_eee(struct dsa_switch *ds, int port, struct ethtool_eee *eee)
|
|
-{
|
|
- struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
|
|
- u32 lpi_en = QCA8K_REG_EEE_CTRL_LPI_EN(port);
|
|
- u32 reg;
|
|
- int ret;
|
|
-
|
|
- mutex_lock(&priv->reg_mutex);
|
|
- ret = qca8k_read(priv, QCA8K_REG_EEE_CTRL, ®);
|
|
- if (ret < 0)
|
|
- goto exit;
|
|
-
|
|
- if (eee->eee_enabled)
|
|
- reg |= lpi_en;
|
|
- else
|
|
- reg &= ~lpi_en;
|
|
- ret = qca8k_write(priv, QCA8K_REG_EEE_CTRL, reg);
|
|
-
|
|
-exit:
|
|
- mutex_unlock(&priv->reg_mutex);
|
|
- return ret;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_get_mac_eee(struct dsa_switch *ds, int port, struct ethtool_eee *e)
|
|
-{
|
|
- /* Nothing to do on the port's MAC */
|
|
- return 0;
|
|
-}
|
|
-
|
|
-static void
|
|
-qca8k_port_stp_state_set(struct dsa_switch *ds, int port, u8 state)
|
|
-{
|
|
- struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
|
|
- u32 stp_state;
|
|
-
|
|
- switch (state) {
|
|
- case BR_STATE_DISABLED:
|
|
- stp_state = QCA8K_PORT_LOOKUP_STATE_DISABLED;
|
|
- break;
|
|
- case BR_STATE_BLOCKING:
|
|
- stp_state = QCA8K_PORT_LOOKUP_STATE_BLOCKING;
|
|
- break;
|
|
- case BR_STATE_LISTENING:
|
|
- stp_state = QCA8K_PORT_LOOKUP_STATE_LISTENING;
|
|
- break;
|
|
- case BR_STATE_LEARNING:
|
|
- stp_state = QCA8K_PORT_LOOKUP_STATE_LEARNING;
|
|
- break;
|
|
- case BR_STATE_FORWARDING:
|
|
- default:
|
|
- stp_state = QCA8K_PORT_LOOKUP_STATE_FORWARD;
|
|
- break;
|
|
- }
|
|
-
|
|
- qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port),
|
|
- QCA8K_PORT_LOOKUP_STATE_MASK, stp_state);
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_port_bridge_join(struct dsa_switch *ds, int port, struct net_device *br)
|
|
-{
|
|
- struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
|
|
- int port_mask, cpu_port;
|
|
- int i, ret;
|
|
-
|
|
- cpu_port = dsa_to_port(ds, port)->cpu_dp->index;
|
|
- port_mask = BIT(cpu_port);
|
|
-
|
|
- for (i = 0; i < QCA8K_NUM_PORTS; i++) {
|
|
- if (dsa_is_cpu_port(ds, i))
|
|
- continue;
|
|
- if (dsa_to_port(ds, i)->bridge_dev != br)
|
|
- continue;
|
|
- /* Add this port to the portvlan mask of the other ports
|
|
- * in the bridge
|
|
- */
|
|
- ret = regmap_set_bits(priv->regmap,
|
|
- QCA8K_PORT_LOOKUP_CTRL(i),
|
|
- BIT(port));
|
|
- if (ret)
|
|
- return ret;
|
|
- if (i != port)
|
|
- port_mask |= BIT(i);
|
|
- }
|
|
-
|
|
- /* Add all other ports to this ports portvlan mask */
|
|
- ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port),
|
|
- QCA8K_PORT_LOOKUP_MEMBER, port_mask);
|
|
-
|
|
- return ret;
|
|
-}
|
|
-
|
|
-static void
|
|
-qca8k_port_bridge_leave(struct dsa_switch *ds, int port, struct net_device *br)
|
|
-{
|
|
- struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
|
|
- int cpu_port, i;
|
|
-
|
|
- cpu_port = dsa_to_port(ds, port)->cpu_dp->index;
|
|
-
|
|
- for (i = 0; i < QCA8K_NUM_PORTS; i++) {
|
|
- if (dsa_is_cpu_port(ds, i))
|
|
- continue;
|
|
- if (dsa_to_port(ds, i)->bridge_dev != br)
|
|
- continue;
|
|
- /* Remove this port to the portvlan mask of the other ports
|
|
- * in the bridge
|
|
- */
|
|
- regmap_clear_bits(priv->regmap,
|
|
- QCA8K_PORT_LOOKUP_CTRL(i),
|
|
- BIT(port));
|
|
- }
|
|
-
|
|
- /* Set the cpu port to be the only one in the portvlan mask of
|
|
- * this port
|
|
- */
|
|
- qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port),
|
|
- QCA8K_PORT_LOOKUP_MEMBER, BIT(cpu_port));
|
|
-}
|
|
-
|
|
-static void
|
|
-qca8k_port_fast_age(struct dsa_switch *ds, int port)
|
|
-{
|
|
- struct qca8k_priv *priv = ds->priv;
|
|
-
|
|
- mutex_lock(&priv->reg_mutex);
|
|
- qca8k_fdb_access(priv, QCA8K_FDB_FLUSH_PORT, port);
|
|
- mutex_unlock(&priv->reg_mutex);
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_set_ageing_time(struct dsa_switch *ds, unsigned int msecs)
|
|
-{
|
|
- struct qca8k_priv *priv = ds->priv;
|
|
- unsigned int secs = msecs / 1000;
|
|
- u32 val;
|
|
-
|
|
- /* AGE_TIME reg is set in 7s step */
|
|
- val = secs / 7;
|
|
-
|
|
- /* Handle case with 0 as val to NOT disable
|
|
- * learning
|
|
- */
|
|
- if (!val)
|
|
- val = 1;
|
|
-
|
|
- return regmap_update_bits(priv->regmap, QCA8K_REG_ATU_CTRL, QCA8K_ATU_AGE_TIME_MASK,
|
|
- QCA8K_ATU_AGE_TIME(val));
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_port_enable(struct dsa_switch *ds, int port,
|
|
- struct phy_device *phy)
|
|
-{
|
|
- struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
|
|
-
|
|
- qca8k_port_set_status(priv, port, 1);
|
|
- priv->port_enabled_map |= BIT(port);
|
|
-
|
|
- if (dsa_is_user_port(ds, port))
|
|
- phy_support_asym_pause(phy);
|
|
-
|
|
- return 0;
|
|
-}
|
|
-
|
|
-static void
|
|
-qca8k_port_disable(struct dsa_switch *ds, int port)
|
|
-{
|
|
- struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
|
|
-
|
|
- qca8k_port_set_status(priv, port, 0);
|
|
- priv->port_enabled_map &= ~BIT(port);
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_port_change_mtu(struct dsa_switch *ds, int port, int new_mtu)
|
|
-{
|
|
- struct qca8k_priv *priv = ds->priv;
|
|
- int ret;
|
|
-
|
|
- /* We have only have a general MTU setting.
|
|
- * DSA always set the CPU port's MTU to the largest MTU of the slave
|
|
- * ports.
|
|
- * Setting MTU just for the CPU port is sufficient to correctly set a
|
|
- * value for every port.
|
|
- */
|
|
- if (!dsa_is_cpu_port(ds, port))
|
|
- return 0;
|
|
-
|
|
- /* To change the MAX_FRAME_SIZE the cpu ports must be off or
|
|
- * the switch panics.
|
|
- * Turn off both cpu ports before applying the new value to prevent
|
|
- * this.
|
|
- */
|
|
- if (priv->port_enabled_map & BIT(0))
|
|
- qca8k_port_set_status(priv, 0, 0);
|
|
-
|
|
- if (priv->port_enabled_map & BIT(6))
|
|
- qca8k_port_set_status(priv, 6, 0);
|
|
-
|
|
- /* Include L2 header / FCS length */
|
|
- ret = qca8k_write(priv, QCA8K_MAX_FRAME_SIZE, new_mtu + ETH_HLEN + ETH_FCS_LEN);
|
|
-
|
|
- if (priv->port_enabled_map & BIT(0))
|
|
- qca8k_port_set_status(priv, 0, 1);
|
|
-
|
|
- if (priv->port_enabled_map & BIT(6))
|
|
- qca8k_port_set_status(priv, 6, 1);
|
|
-
|
|
- return ret;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_port_max_mtu(struct dsa_switch *ds, int port)
|
|
-{
|
|
- return QCA8K_MAX_MTU;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_port_fdb_insert(struct qca8k_priv *priv, const u8 *addr,
|
|
- u16 port_mask, u16 vid)
|
|
-{
|
|
- /* Set the vid to the port vlan id if no vid is set */
|
|
- if (!vid)
|
|
- vid = QCA8K_PORT_VID_DEF;
|
|
-
|
|
- return qca8k_fdb_add(priv, addr, port_mask, vid,
|
|
- QCA8K_ATU_STATUS_STATIC);
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_port_fdb_add(struct dsa_switch *ds, int port,
|
|
- const unsigned char *addr, u16 vid)
|
|
-{
|
|
- struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
|
|
- u16 port_mask = BIT(port);
|
|
-
|
|
- return qca8k_port_fdb_insert(priv, addr, port_mask, vid);
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_port_fdb_del(struct dsa_switch *ds, int port,
|
|
- const unsigned char *addr, u16 vid)
|
|
-{
|
|
- struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
|
|
- u16 port_mask = BIT(port);
|
|
-
|
|
- if (!vid)
|
|
- vid = QCA8K_PORT_VID_DEF;
|
|
-
|
|
- return qca8k_fdb_del(priv, addr, port_mask, vid);
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_port_fdb_dump(struct dsa_switch *ds, int port,
|
|
- dsa_fdb_dump_cb_t *cb, void *data)
|
|
-{
|
|
- struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
|
|
- struct qca8k_fdb _fdb = { 0 };
|
|
- int cnt = QCA8K_NUM_FDB_RECORDS;
|
|
- bool is_static;
|
|
- int ret = 0;
|
|
-
|
|
- mutex_lock(&priv->reg_mutex);
|
|
- while (cnt-- && !qca8k_fdb_next(priv, &_fdb, port)) {
|
|
- if (!_fdb.aging)
|
|
- break;
|
|
- is_static = (_fdb.aging == QCA8K_ATU_STATUS_STATIC);
|
|
- ret = cb(_fdb.mac, _fdb.vid, is_static, data);
|
|
- if (ret)
|
|
- break;
|
|
- }
|
|
- mutex_unlock(&priv->reg_mutex);
|
|
-
|
|
- return 0;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_port_mdb_add(struct dsa_switch *ds, int port,
|
|
- const struct switchdev_obj_port_mdb *mdb)
|
|
-{
|
|
- struct qca8k_priv *priv = ds->priv;
|
|
- const u8 *addr = mdb->addr;
|
|
- u16 vid = mdb->vid;
|
|
-
|
|
- return qca8k_fdb_search_and_insert(priv, BIT(port), addr, vid);
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_port_mdb_del(struct dsa_switch *ds, int port,
|
|
- const struct switchdev_obj_port_mdb *mdb)
|
|
-{
|
|
- struct qca8k_priv *priv = ds->priv;
|
|
- const u8 *addr = mdb->addr;
|
|
- u16 vid = mdb->vid;
|
|
-
|
|
- return qca8k_fdb_search_and_del(priv, BIT(port), addr, vid);
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_port_mirror_add(struct dsa_switch *ds, int port,
|
|
- struct dsa_mall_mirror_tc_entry *mirror,
|
|
- bool ingress)
|
|
-{
|
|
- struct qca8k_priv *priv = ds->priv;
|
|
- int monitor_port, ret;
|
|
- u32 reg, val;
|
|
-
|
|
- /* Check for existent entry */
|
|
- if ((ingress ? priv->mirror_rx : priv->mirror_tx) & BIT(port))
|
|
- return -EEXIST;
|
|
-
|
|
- ret = regmap_read(priv->regmap, QCA8K_REG_GLOBAL_FW_CTRL0, &val);
|
|
- if (ret)
|
|
- return ret;
|
|
-
|
|
- /* QCA83xx can have only one port set to mirror mode.
|
|
- * Check that the correct port is requested and return error otherwise.
|
|
- * When no mirror port is set, the values is set to 0xF
|
|
- */
|
|
- monitor_port = FIELD_GET(QCA8K_GLOBAL_FW_CTRL0_MIRROR_PORT_NUM, val);
|
|
- if (monitor_port != 0xF && monitor_port != mirror->to_local_port)
|
|
- return -EEXIST;
|
|
-
|
|
- /* Set the monitor port */
|
|
- val = FIELD_PREP(QCA8K_GLOBAL_FW_CTRL0_MIRROR_PORT_NUM,
|
|
- mirror->to_local_port);
|
|
- ret = regmap_update_bits(priv->regmap, QCA8K_REG_GLOBAL_FW_CTRL0,
|
|
- QCA8K_GLOBAL_FW_CTRL0_MIRROR_PORT_NUM, val);
|
|
- if (ret)
|
|
- return ret;
|
|
-
|
|
- if (ingress) {
|
|
- reg = QCA8K_PORT_LOOKUP_CTRL(port);
|
|
- val = QCA8K_PORT_LOOKUP_ING_MIRROR_EN;
|
|
- } else {
|
|
- reg = QCA8K_REG_PORT_HOL_CTRL1(port);
|
|
- val = QCA8K_PORT_HOL_CTRL1_EG_MIRROR_EN;
|
|
- }
|
|
-
|
|
- ret = regmap_update_bits(priv->regmap, reg, val, val);
|
|
- if (ret)
|
|
- return ret;
|
|
-
|
|
- /* Track mirror port for tx and rx to decide when the
|
|
- * mirror port has to be disabled.
|
|
- */
|
|
- if (ingress)
|
|
- priv->mirror_rx |= BIT(port);
|
|
- else
|
|
- priv->mirror_tx |= BIT(port);
|
|
-
|
|
- return 0;
|
|
-}
|
|
-
|
|
-static void
|
|
-qca8k_port_mirror_del(struct dsa_switch *ds, int port,
|
|
- struct dsa_mall_mirror_tc_entry *mirror)
|
|
-{
|
|
- struct qca8k_priv *priv = ds->priv;
|
|
- u32 reg, val;
|
|
- int ret;
|
|
-
|
|
- if (mirror->ingress) {
|
|
- reg = QCA8K_PORT_LOOKUP_CTRL(port);
|
|
- val = QCA8K_PORT_LOOKUP_ING_MIRROR_EN;
|
|
- } else {
|
|
- reg = QCA8K_REG_PORT_HOL_CTRL1(port);
|
|
- val = QCA8K_PORT_HOL_CTRL1_EG_MIRROR_EN;
|
|
- }
|
|
-
|
|
- ret = regmap_clear_bits(priv->regmap, reg, val);
|
|
- if (ret)
|
|
- goto err;
|
|
-
|
|
- if (mirror->ingress)
|
|
- priv->mirror_rx &= ~BIT(port);
|
|
- else
|
|
- priv->mirror_tx &= ~BIT(port);
|
|
-
|
|
- /* No port set to send packet to mirror port. Disable mirror port */
|
|
- if (!priv->mirror_rx && !priv->mirror_tx) {
|
|
- val = FIELD_PREP(QCA8K_GLOBAL_FW_CTRL0_MIRROR_PORT_NUM, 0xF);
|
|
- ret = regmap_update_bits(priv->regmap, QCA8K_REG_GLOBAL_FW_CTRL0,
|
|
- QCA8K_GLOBAL_FW_CTRL0_MIRROR_PORT_NUM, val);
|
|
- if (ret)
|
|
- goto err;
|
|
- }
|
|
-err:
|
|
- dev_err(priv->dev, "Failed to del mirror port from %d", port);
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_port_vlan_filtering(struct dsa_switch *ds, int port, bool vlan_filtering,
|
|
- struct netlink_ext_ack *extack)
|
|
-{
|
|
- struct qca8k_priv *priv = ds->priv;
|
|
- int ret;
|
|
-
|
|
- if (vlan_filtering) {
|
|
- ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port),
|
|
- QCA8K_PORT_LOOKUP_VLAN_MODE_MASK,
|
|
- QCA8K_PORT_LOOKUP_VLAN_MODE_SECURE);
|
|
- } else {
|
|
- ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port),
|
|
- QCA8K_PORT_LOOKUP_VLAN_MODE_MASK,
|
|
- QCA8K_PORT_LOOKUP_VLAN_MODE_NONE);
|
|
- }
|
|
-
|
|
- return ret;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_port_vlan_add(struct dsa_switch *ds, int port,
|
|
- const struct switchdev_obj_port_vlan *vlan,
|
|
- struct netlink_ext_ack *extack)
|
|
-{
|
|
- bool untagged = vlan->flags & BRIDGE_VLAN_INFO_UNTAGGED;
|
|
- bool pvid = vlan->flags & BRIDGE_VLAN_INFO_PVID;
|
|
- struct qca8k_priv *priv = ds->priv;
|
|
- int ret;
|
|
-
|
|
- ret = qca8k_vlan_add(priv, port, vlan->vid, untagged);
|
|
- if (ret) {
|
|
- dev_err(priv->dev, "Failed to add VLAN to port %d (%d)", port, ret);
|
|
- return ret;
|
|
- }
|
|
-
|
|
- if (pvid) {
|
|
- ret = qca8k_rmw(priv, QCA8K_EGRESS_VLAN(port),
|
|
- QCA8K_EGREES_VLAN_PORT_MASK(port),
|
|
- QCA8K_EGREES_VLAN_PORT(port, vlan->vid));
|
|
- if (ret)
|
|
- return ret;
|
|
-
|
|
- ret = qca8k_write(priv, QCA8K_REG_PORT_VLAN_CTRL0(port),
|
|
- QCA8K_PORT_VLAN_CVID(vlan->vid) |
|
|
- QCA8K_PORT_VLAN_SVID(vlan->vid));
|
|
- }
|
|
-
|
|
- return ret;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_port_vlan_del(struct dsa_switch *ds, int port,
|
|
- const struct switchdev_obj_port_vlan *vlan)
|
|
-{
|
|
- struct qca8k_priv *priv = ds->priv;
|
|
- int ret;
|
|
-
|
|
- ret = qca8k_vlan_del(priv, port, vlan->vid);
|
|
- if (ret)
|
|
- dev_err(priv->dev, "Failed to delete VLAN from port %d (%d)", port, ret);
|
|
-
|
|
- return ret;
|
|
-}
|
|
-
|
|
-static u32 qca8k_get_phy_flags(struct dsa_switch *ds, int port)
|
|
-{
|
|
- struct qca8k_priv *priv = ds->priv;
|
|
-
|
|
- /* Communicate to the phy internal driver the switch revision.
|
|
- * Based on the switch revision different values needs to be
|
|
- * set to the dbg and mmd reg on the phy.
|
|
- * The first 2 bit are used to communicate the switch revision
|
|
- * to the phy driver.
|
|
- */
|
|
- if (port > 0 && port < 6)
|
|
- return priv->switch_revision;
|
|
-
|
|
- return 0;
|
|
-}
|
|
-
|
|
-static enum dsa_tag_protocol
|
|
-qca8k_get_tag_protocol(struct dsa_switch *ds, int port,
|
|
- enum dsa_tag_protocol mp)
|
|
-{
|
|
- return DSA_TAG_PROTO_QCA;
|
|
-}
|
|
-
|
|
-static bool
|
|
-qca8k_lag_can_offload(struct dsa_switch *ds,
|
|
- struct net_device *lag,
|
|
- struct netdev_lag_upper_info *info)
|
|
-{
|
|
- struct dsa_port *dp;
|
|
- int id, members = 0;
|
|
-
|
|
- id = dsa_lag_id(ds->dst, lag);
|
|
- if (id < 0 || id >= ds->num_lag_ids)
|
|
- return false;
|
|
-
|
|
- dsa_lag_foreach_port(dp, ds->dst, lag)
|
|
- /* Includes the port joining the LAG */
|
|
- members++;
|
|
-
|
|
- if (members > QCA8K_NUM_PORTS_FOR_LAG)
|
|
- return false;
|
|
-
|
|
- if (info->tx_type != NETDEV_LAG_TX_TYPE_HASH)
|
|
- return false;
|
|
-
|
|
- if (info->hash_type != NETDEV_LAG_HASH_L2 &&
|
|
- info->hash_type != NETDEV_LAG_HASH_L23)
|
|
- return false;
|
|
-
|
|
- return true;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_lag_setup_hash(struct dsa_switch *ds,
|
|
- struct net_device *lag,
|
|
- struct netdev_lag_upper_info *info)
|
|
-{
|
|
- struct qca8k_priv *priv = ds->priv;
|
|
- bool unique_lag = true;
|
|
- u32 hash = 0;
|
|
- int i, id;
|
|
-
|
|
- id = dsa_lag_id(ds->dst, lag);
|
|
-
|
|
- switch (info->hash_type) {
|
|
- case NETDEV_LAG_HASH_L23:
|
|
- hash |= QCA8K_TRUNK_HASH_SIP_EN;
|
|
- hash |= QCA8K_TRUNK_HASH_DIP_EN;
|
|
- fallthrough;
|
|
- case NETDEV_LAG_HASH_L2:
|
|
- hash |= QCA8K_TRUNK_HASH_SA_EN;
|
|
- hash |= QCA8K_TRUNK_HASH_DA_EN;
|
|
- break;
|
|
- default: /* We should NEVER reach this */
|
|
- return -EOPNOTSUPP;
|
|
- }
|
|
-
|
|
- /* Check if we are the unique configured LAG */
|
|
- dsa_lags_foreach_id(i, ds->dst)
|
|
- if (i != id && dsa_lag_dev(ds->dst, i)) {
|
|
- unique_lag = false;
|
|
- break;
|
|
- }
|
|
-
|
|
- /* Hash Mode is global. Make sure the same Hash Mode
|
|
- * is set to all the 4 possible lag.
|
|
- * If we are the unique LAG we can set whatever hash
|
|
- * mode we want.
|
|
- * To change hash mode it's needed to remove all LAG
|
|
- * and change the mode with the latest.
|
|
- */
|
|
- if (unique_lag) {
|
|
- priv->lag_hash_mode = hash;
|
|
- } else if (priv->lag_hash_mode != hash) {
|
|
- netdev_err(lag, "Error: Mismateched Hash Mode across different lag is not supported\n");
|
|
- return -EOPNOTSUPP;
|
|
- }
|
|
-
|
|
- return regmap_update_bits(priv->regmap, QCA8K_TRUNK_HASH_EN_CTRL,
|
|
- QCA8K_TRUNK_HASH_MASK, hash);
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_lag_refresh_portmap(struct dsa_switch *ds, int port,
|
|
- struct net_device *lag, bool delete)
|
|
-{
|
|
- struct qca8k_priv *priv = ds->priv;
|
|
- int ret, id, i;
|
|
- u32 val;
|
|
-
|
|
- id = dsa_lag_id(ds->dst, lag);
|
|
-
|
|
- /* Read current port member */
|
|
- ret = regmap_read(priv->regmap, QCA8K_REG_GOL_TRUNK_CTRL0, &val);
|
|
- if (ret)
|
|
- return ret;
|
|
-
|
|
- /* Shift val to the correct trunk */
|
|
- val >>= QCA8K_REG_GOL_TRUNK_SHIFT(id);
|
|
- val &= QCA8K_REG_GOL_TRUNK_MEMBER_MASK;
|
|
- if (delete)
|
|
- val &= ~BIT(port);
|
|
- else
|
|
- val |= BIT(port);
|
|
-
|
|
- /* Update port member. With empty portmap disable trunk */
|
|
- ret = regmap_update_bits(priv->regmap, QCA8K_REG_GOL_TRUNK_CTRL0,
|
|
- QCA8K_REG_GOL_TRUNK_MEMBER(id) |
|
|
- QCA8K_REG_GOL_TRUNK_EN(id),
|
|
- !val << QCA8K_REG_GOL_TRUNK_SHIFT(id) |
|
|
- val << QCA8K_REG_GOL_TRUNK_SHIFT(id));
|
|
-
|
|
- /* Search empty member if adding or port on deleting */
|
|
- for (i = 0; i < QCA8K_NUM_PORTS_FOR_LAG; i++) {
|
|
- ret = regmap_read(priv->regmap, QCA8K_REG_GOL_TRUNK_CTRL(id), &val);
|
|
- if (ret)
|
|
- return ret;
|
|
-
|
|
- val >>= QCA8K_REG_GOL_TRUNK_ID_MEM_ID_SHIFT(id, i);
|
|
- val &= QCA8K_REG_GOL_TRUNK_ID_MEM_ID_MASK;
|
|
-
|
|
- if (delete) {
|
|
- /* If port flagged to be disabled assume this member is
|
|
- * empty
|
|
- */
|
|
- if (val != QCA8K_REG_GOL_TRUNK_ID_MEM_ID_EN_MASK)
|
|
- continue;
|
|
-
|
|
- val &= QCA8K_REG_GOL_TRUNK_ID_MEM_ID_PORT_MASK;
|
|
- if (val != port)
|
|
- continue;
|
|
- } else {
|
|
- /* If port flagged to be enabled assume this member is
|
|
- * already set
|
|
- */
|
|
- if (val == QCA8K_REG_GOL_TRUNK_ID_MEM_ID_EN_MASK)
|
|
- continue;
|
|
- }
|
|
-
|
|
- /* We have found the member to add/remove */
|
|
- break;
|
|
- }
|
|
-
|
|
- /* Set port in the correct port mask or disable port if in delete mode */
|
|
- return regmap_update_bits(priv->regmap, QCA8K_REG_GOL_TRUNK_CTRL(id),
|
|
- QCA8K_REG_GOL_TRUNK_ID_MEM_ID_EN(id, i) |
|
|
- QCA8K_REG_GOL_TRUNK_ID_MEM_ID_PORT(id, i),
|
|
- !delete << QCA8K_REG_GOL_TRUNK_ID_MEM_ID_SHIFT(id, i) |
|
|
- port << QCA8K_REG_GOL_TRUNK_ID_MEM_ID_SHIFT(id, i));
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_port_lag_join(struct dsa_switch *ds, int port,
|
|
- struct net_device *lag,
|
|
- struct netdev_lag_upper_info *info)
|
|
-{
|
|
- int ret;
|
|
-
|
|
- if (!qca8k_lag_can_offload(ds, lag, info))
|
|
- return -EOPNOTSUPP;
|
|
-
|
|
- ret = qca8k_lag_setup_hash(ds, lag, info);
|
|
- if (ret)
|
|
- return ret;
|
|
-
|
|
- return qca8k_lag_refresh_portmap(ds, port, lag, false);
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_port_lag_leave(struct dsa_switch *ds, int port,
|
|
- struct net_device *lag)
|
|
-{
|
|
- return qca8k_lag_refresh_portmap(ds, port, lag, true);
|
|
-}
|
|
-
|
|
-static void
|
|
-qca8k_master_change(struct dsa_switch *ds, const struct net_device *master,
|
|
- bool operational)
|
|
-{
|
|
- struct dsa_port *dp = master->dsa_ptr;
|
|
- struct qca8k_priv *priv = ds->priv;
|
|
-
|
|
- /* Ethernet MIB/MDIO is only supported for CPU port 0 */
|
|
- if (dp->index != 0)
|
|
- return;
|
|
-
|
|
- mutex_lock(&priv->mgmt_eth_data.mutex);
|
|
- mutex_lock(&priv->mib_eth_data.mutex);
|
|
-
|
|
- priv->mgmt_master = operational ? (struct net_device *)master : NULL;
|
|
-
|
|
- mutex_unlock(&priv->mib_eth_data.mutex);
|
|
- mutex_unlock(&priv->mgmt_eth_data.mutex);
|
|
-}
|
|
-
|
|
-static int qca8k_connect_tag_protocol(struct dsa_switch *ds,
|
|
- enum dsa_tag_protocol proto)
|
|
-{
|
|
- struct qca_tagger_data *tagger_data;
|
|
-
|
|
- switch (proto) {
|
|
- case DSA_TAG_PROTO_QCA:
|
|
- tagger_data = ds->tagger_data;
|
|
-
|
|
- tagger_data->rw_reg_ack_handler = qca8k_rw_reg_ack_handler;
|
|
- tagger_data->mib_autocast_handler = qca8k_mib_autocast_handler;
|
|
-
|
|
- break;
|
|
- default:
|
|
- return -EOPNOTSUPP;
|
|
- }
|
|
-
|
|
- return 0;
|
|
-}
|
|
-
|
|
-static const struct dsa_switch_ops qca8k_switch_ops = {
|
|
- .get_tag_protocol = qca8k_get_tag_protocol,
|
|
- .setup = qca8k_setup,
|
|
- .get_strings = qca8k_get_strings,
|
|
- .get_ethtool_stats = qca8k_get_ethtool_stats,
|
|
- .get_sset_count = qca8k_get_sset_count,
|
|
- .set_ageing_time = qca8k_set_ageing_time,
|
|
- .get_mac_eee = qca8k_get_mac_eee,
|
|
- .set_mac_eee = qca8k_set_mac_eee,
|
|
- .port_enable = qca8k_port_enable,
|
|
- .port_disable = qca8k_port_disable,
|
|
- .port_change_mtu = qca8k_port_change_mtu,
|
|
- .port_max_mtu = qca8k_port_max_mtu,
|
|
- .port_stp_state_set = qca8k_port_stp_state_set,
|
|
- .port_bridge_join = qca8k_port_bridge_join,
|
|
- .port_bridge_leave = qca8k_port_bridge_leave,
|
|
- .port_fast_age = qca8k_port_fast_age,
|
|
- .port_fdb_add = qca8k_port_fdb_add,
|
|
- .port_fdb_del = qca8k_port_fdb_del,
|
|
- .port_fdb_dump = qca8k_port_fdb_dump,
|
|
- .port_mdb_add = qca8k_port_mdb_add,
|
|
- .port_mdb_del = qca8k_port_mdb_del,
|
|
- .port_mirror_add = qca8k_port_mirror_add,
|
|
- .port_mirror_del = qca8k_port_mirror_del,
|
|
- .port_vlan_filtering = qca8k_port_vlan_filtering,
|
|
- .port_vlan_add = qca8k_port_vlan_add,
|
|
- .port_vlan_del = qca8k_port_vlan_del,
|
|
- .phylink_validate = qca8k_phylink_validate,
|
|
- .phylink_mac_link_state = qca8k_phylink_mac_link_state,
|
|
- .phylink_mac_config = qca8k_phylink_mac_config,
|
|
- .phylink_mac_link_down = qca8k_phylink_mac_link_down,
|
|
- .phylink_mac_link_up = qca8k_phylink_mac_link_up,
|
|
- .get_phy_flags = qca8k_get_phy_flags,
|
|
- .port_lag_join = qca8k_port_lag_join,
|
|
- .port_lag_leave = qca8k_port_lag_leave,
|
|
- .master_state_change = qca8k_master_change,
|
|
- .connect_tag_protocol = qca8k_connect_tag_protocol,
|
|
-};
|
|
-
|
|
-static int qca8k_read_switch_id(struct qca8k_priv *priv)
|
|
-{
|
|
- const struct qca8k_match_data *data;
|
|
- u32 val;
|
|
- u8 id;
|
|
- int ret;
|
|
-
|
|
- /* get the switches ID from the compatible */
|
|
- data = of_device_get_match_data(priv->dev);
|
|
- if (!data)
|
|
- return -ENODEV;
|
|
-
|
|
- ret = qca8k_read(priv, QCA8K_REG_MASK_CTRL, &val);
|
|
- if (ret < 0)
|
|
- return -ENODEV;
|
|
-
|
|
- id = QCA8K_MASK_CTRL_DEVICE_ID(val);
|
|
- if (id != data->id) {
|
|
- dev_err(priv->dev, "Switch id detected %x but expected %x", id, data->id);
|
|
- return -ENODEV;
|
|
- }
|
|
-
|
|
- priv->switch_id = id;
|
|
-
|
|
- /* Save revision to communicate to the internal PHY driver */
|
|
- priv->switch_revision = QCA8K_MASK_CTRL_REV_ID(val);
|
|
-
|
|
- return 0;
|
|
-}
|
|
-
|
|
-static int
|
|
-qca8k_sw_probe(struct mdio_device *mdiodev)
|
|
-{
|
|
- struct qca8k_priv *priv;
|
|
- int ret;
|
|
-
|
|
- /* allocate the private data struct so that we can probe the switches
|
|
- * ID register
|
|
- */
|
|
- priv = devm_kzalloc(&mdiodev->dev, sizeof(*priv), GFP_KERNEL);
|
|
- if (!priv)
|
|
- return -ENOMEM;
|
|
-
|
|
- priv->bus = mdiodev->bus;
|
|
- priv->dev = &mdiodev->dev;
|
|
-
|
|
- priv->reset_gpio = devm_gpiod_get_optional(priv->dev, "reset",
|
|
- GPIOD_ASIS);
|
|
- if (IS_ERR(priv->reset_gpio))
|
|
- return PTR_ERR(priv->reset_gpio);
|
|
-
|
|
- if (priv->reset_gpio) {
|
|
- gpiod_set_value_cansleep(priv->reset_gpio, 1);
|
|
- /* The active low duration must be greater than 10 ms
|
|
- * and checkpatch.pl wants 20 ms.
|
|
- */
|
|
- msleep(20);
|
|
- gpiod_set_value_cansleep(priv->reset_gpio, 0);
|
|
- }
|
|
-
|
|
- /* Start by setting up the register mapping */
|
|
- priv->regmap = devm_regmap_init(&mdiodev->dev, NULL, priv,
|
|
- &qca8k_regmap_config);
|
|
- if (IS_ERR(priv->regmap)) {
|
|
- dev_err(priv->dev, "regmap initialization failed");
|
|
- return PTR_ERR(priv->regmap);
|
|
- }
|
|
-
|
|
- priv->mdio_cache.page = 0xffff;
|
|
- priv->mdio_cache.lo = 0xffff;
|
|
- priv->mdio_cache.hi = 0xffff;
|
|
-
|
|
- /* Check the detected switch id */
|
|
- ret = qca8k_read_switch_id(priv);
|
|
- if (ret)
|
|
- return ret;
|
|
-
|
|
- priv->ds = devm_kzalloc(&mdiodev->dev, sizeof(*priv->ds), GFP_KERNEL);
|
|
- if (!priv->ds)
|
|
- return -ENOMEM;
|
|
-
|
|
- mutex_init(&priv->mgmt_eth_data.mutex);
|
|
- init_completion(&priv->mgmt_eth_data.rw_done);
|
|
-
|
|
- mutex_init(&priv->mib_eth_data.mutex);
|
|
- init_completion(&priv->mib_eth_data.rw_done);
|
|
-
|
|
- priv->ds->dev = &mdiodev->dev;
|
|
- priv->ds->num_ports = QCA8K_NUM_PORTS;
|
|
- priv->ds->priv = priv;
|
|
- priv->ds->ops = &qca8k_switch_ops;
|
|
- mutex_init(&priv->reg_mutex);
|
|
- dev_set_drvdata(&mdiodev->dev, priv);
|
|
-
|
|
- return dsa_register_switch(priv->ds);
|
|
-}
|
|
-
|
|
-static void
|
|
-qca8k_sw_remove(struct mdio_device *mdiodev)
|
|
-{
|
|
- struct qca8k_priv *priv = dev_get_drvdata(&mdiodev->dev);
|
|
- int i;
|
|
-
|
|
- if (!priv)
|
|
- return;
|
|
-
|
|
- for (i = 0; i < QCA8K_NUM_PORTS; i++)
|
|
- qca8k_port_set_status(priv, i, 0);
|
|
-
|
|
- dsa_unregister_switch(priv->ds);
|
|
-
|
|
- dev_set_drvdata(&mdiodev->dev, NULL);
|
|
-}
|
|
-
|
|
-static void qca8k_sw_shutdown(struct mdio_device *mdiodev)
|
|
-{
|
|
- struct qca8k_priv *priv = dev_get_drvdata(&mdiodev->dev);
|
|
-
|
|
- if (!priv)
|
|
- return;
|
|
-
|
|
- dsa_switch_shutdown(priv->ds);
|
|
-
|
|
- dev_set_drvdata(&mdiodev->dev, NULL);
|
|
-}
|
|
-
|
|
-#ifdef CONFIG_PM_SLEEP
|
|
-static void
|
|
-qca8k_set_pm(struct qca8k_priv *priv, int enable)
|
|
-{
|
|
- int port;
|
|
-
|
|
- for (port = 0; port < QCA8K_NUM_PORTS; port++) {
|
|
- /* Do not enable on resume if the port was
|
|
- * disabled before.
|
|
- */
|
|
- if (!(priv->port_enabled_map & BIT(port)))
|
|
- continue;
|
|
-
|
|
- qca8k_port_set_status(priv, port, enable);
|
|
- }
|
|
-}
|
|
-
|
|
-static int qca8k_suspend(struct device *dev)
|
|
-{
|
|
- struct qca8k_priv *priv = dev_get_drvdata(dev);
|
|
-
|
|
- qca8k_set_pm(priv, 0);
|
|
-
|
|
- return dsa_switch_suspend(priv->ds);
|
|
-}
|
|
-
|
|
-static int qca8k_resume(struct device *dev)
|
|
-{
|
|
- struct qca8k_priv *priv = dev_get_drvdata(dev);
|
|
-
|
|
- qca8k_set_pm(priv, 1);
|
|
-
|
|
- return dsa_switch_resume(priv->ds);
|
|
-}
|
|
-#endif /* CONFIG_PM_SLEEP */
|
|
-
|
|
-static SIMPLE_DEV_PM_OPS(qca8k_pm_ops,
|
|
- qca8k_suspend, qca8k_resume);
|
|
-
|
|
-static const struct qca8k_match_data qca8327 = {
|
|
- .id = QCA8K_ID_QCA8327,
|
|
- .reduced_package = true,
|
|
- .mib_count = QCA8K_QCA832X_MIB_COUNT,
|
|
-};
|
|
-
|
|
-static const struct qca8k_match_data qca8328 = {
|
|
- .id = QCA8K_ID_QCA8327,
|
|
- .mib_count = QCA8K_QCA832X_MIB_COUNT,
|
|
-};
|
|
-
|
|
-static const struct qca8k_match_data qca833x = {
|
|
- .id = QCA8K_ID_QCA8337,
|
|
- .mib_count = QCA8K_QCA833X_MIB_COUNT,
|
|
-};
|
|
-
|
|
-static const struct of_device_id qca8k_of_match[] = {
|
|
- { .compatible = "qca,qca8327", .data = &qca8327 },
|
|
- { .compatible = "qca,qca8328", .data = &qca8328 },
|
|
- { .compatible = "qca,qca8334", .data = &qca833x },
|
|
- { .compatible = "qca,qca8337", .data = &qca833x },
|
|
- { /* sentinel */ },
|
|
-};
|
|
-
|
|
-static struct mdio_driver qca8kmdio_driver = {
|
|
- .probe = qca8k_sw_probe,
|
|
- .remove = qca8k_sw_remove,
|
|
- .shutdown = qca8k_sw_shutdown,
|
|
- .mdiodrv.driver = {
|
|
- .name = "qca8k",
|
|
- .of_match_table = qca8k_of_match,
|
|
- .pm = &qca8k_pm_ops,
|
|
- },
|
|
-};
|
|
-
|
|
-mdio_module_driver(qca8kmdio_driver);
|
|
-
|
|
-MODULE_AUTHOR("Mathieu Olivari, John Crispin <john@phrozen.org>");
|
|
-MODULE_DESCRIPTION("Driver for QCA8K ethernet switch family");
|
|
-MODULE_LICENSE("GPL v2");
|
|
-MODULE_ALIAS("platform:qca8k");
|
|
--- a/drivers/net/dsa/qca8k.h
|
|
+++ /dev/null
|
|
@@ -1,411 +0,0 @@
|
|
-/* SPDX-License-Identifier: GPL-2.0-only */
|
|
-/*
|
|
- * Copyright (C) 2009 Felix Fietkau <nbd@nbd.name>
|
|
- * Copyright (C) 2011-2012 Gabor Juhos <juhosg@openwrt.org>
|
|
- * Copyright (c) 2015, The Linux Foundation. All rights reserved.
|
|
- */
|
|
-
|
|
-#ifndef __QCA8K_H
|
|
-#define __QCA8K_H
|
|
-
|
|
-#include <linux/delay.h>
|
|
-#include <linux/regmap.h>
|
|
-#include <linux/gpio.h>
|
|
-#include <linux/dsa/tag_qca.h>
|
|
-
|
|
-#define QCA8K_ETHERNET_MDIO_PRIORITY 7
|
|
-#define QCA8K_ETHERNET_PHY_PRIORITY 6
|
|
-#define QCA8K_ETHERNET_TIMEOUT 100
|
|
-
|
|
-#define QCA8K_NUM_PORTS 7
|
|
-#define QCA8K_NUM_CPU_PORTS 2
|
|
-#define QCA8K_MAX_MTU 9000
|
|
-#define QCA8K_NUM_LAGS 4
|
|
-#define QCA8K_NUM_PORTS_FOR_LAG 4
|
|
-
|
|
-#define PHY_ID_QCA8327 0x004dd034
|
|
-#define QCA8K_ID_QCA8327 0x12
|
|
-#define PHY_ID_QCA8337 0x004dd036
|
|
-#define QCA8K_ID_QCA8337 0x13
|
|
-
|
|
-#define QCA8K_QCA832X_MIB_COUNT 39
|
|
-#define QCA8K_QCA833X_MIB_COUNT 41
|
|
-
|
|
-#define QCA8K_BUSY_WAIT_TIMEOUT 2000
|
|
-
|
|
-#define QCA8K_NUM_FDB_RECORDS 2048
|
|
-
|
|
-#define QCA8K_PORT_VID_DEF 1
|
|
-
|
|
-/* Global control registers */
|
|
-#define QCA8K_REG_MASK_CTRL 0x000
|
|
-#define QCA8K_MASK_CTRL_REV_ID_MASK GENMASK(7, 0)
|
|
-#define QCA8K_MASK_CTRL_REV_ID(x) FIELD_GET(QCA8K_MASK_CTRL_REV_ID_MASK, x)
|
|
-#define QCA8K_MASK_CTRL_DEVICE_ID_MASK GENMASK(15, 8)
|
|
-#define QCA8K_MASK_CTRL_DEVICE_ID(x) FIELD_GET(QCA8K_MASK_CTRL_DEVICE_ID_MASK, x)
|
|
-#define QCA8K_REG_PORT0_PAD_CTRL 0x004
|
|
-#define QCA8K_PORT0_PAD_MAC06_EXCHANGE_EN BIT(31)
|
|
-#define QCA8K_PORT0_PAD_SGMII_RXCLK_FALLING_EDGE BIT(19)
|
|
-#define QCA8K_PORT0_PAD_SGMII_TXCLK_FALLING_EDGE BIT(18)
|
|
-#define QCA8K_REG_PORT5_PAD_CTRL 0x008
|
|
-#define QCA8K_REG_PORT6_PAD_CTRL 0x00c
|
|
-#define QCA8K_PORT_PAD_RGMII_EN BIT(26)
|
|
-#define QCA8K_PORT_PAD_RGMII_TX_DELAY_MASK GENMASK(23, 22)
|
|
-#define QCA8K_PORT_PAD_RGMII_TX_DELAY(x) FIELD_PREP(QCA8K_PORT_PAD_RGMII_TX_DELAY_MASK, x)
|
|
-#define QCA8K_PORT_PAD_RGMII_RX_DELAY_MASK GENMASK(21, 20)
|
|
-#define QCA8K_PORT_PAD_RGMII_RX_DELAY(x) FIELD_PREP(QCA8K_PORT_PAD_RGMII_RX_DELAY_MASK, x)
|
|
-#define QCA8K_PORT_PAD_RGMII_TX_DELAY_EN BIT(25)
|
|
-#define QCA8K_PORT_PAD_RGMII_RX_DELAY_EN BIT(24)
|
|
-#define QCA8K_PORT_PAD_SGMII_EN BIT(7)
|
|
-#define QCA8K_REG_PWS 0x010
|
|
-#define QCA8K_PWS_POWER_ON_SEL BIT(31)
|
|
-/* This reg is only valid for QCA832x and toggle the package
|
|
- * type from 176 pin (by default) to 148 pin used on QCA8327
|
|
- */
|
|
-#define QCA8327_PWS_PACKAGE148_EN BIT(30)
|
|
-#define QCA8K_PWS_LED_OPEN_EN_CSR BIT(24)
|
|
-#define QCA8K_PWS_SERDES_AEN_DIS BIT(7)
|
|
-#define QCA8K_REG_MODULE_EN 0x030
|
|
-#define QCA8K_MODULE_EN_MIB BIT(0)
|
|
-#define QCA8K_REG_MIB 0x034
|
|
-#define QCA8K_MIB_FUNC GENMASK(26, 24)
|
|
-#define QCA8K_MIB_CPU_KEEP BIT(20)
|
|
-#define QCA8K_MIB_BUSY BIT(17)
|
|
-#define QCA8K_MDIO_MASTER_CTRL 0x3c
|
|
-#define QCA8K_MDIO_MASTER_BUSY BIT(31)
|
|
-#define QCA8K_MDIO_MASTER_EN BIT(30)
|
|
-#define QCA8K_MDIO_MASTER_READ BIT(27)
|
|
-#define QCA8K_MDIO_MASTER_WRITE 0
|
|
-#define QCA8K_MDIO_MASTER_SUP_PRE BIT(26)
|
|
-#define QCA8K_MDIO_MASTER_PHY_ADDR_MASK GENMASK(25, 21)
|
|
-#define QCA8K_MDIO_MASTER_PHY_ADDR(x) FIELD_PREP(QCA8K_MDIO_MASTER_PHY_ADDR_MASK, x)
|
|
-#define QCA8K_MDIO_MASTER_REG_ADDR_MASK GENMASK(20, 16)
|
|
-#define QCA8K_MDIO_MASTER_REG_ADDR(x) FIELD_PREP(QCA8K_MDIO_MASTER_REG_ADDR_MASK, x)
|
|
-#define QCA8K_MDIO_MASTER_DATA_MASK GENMASK(15, 0)
|
|
-#define QCA8K_MDIO_MASTER_DATA(x) FIELD_PREP(QCA8K_MDIO_MASTER_DATA_MASK, x)
|
|
-#define QCA8K_MDIO_MASTER_MAX_PORTS 5
|
|
-#define QCA8K_MDIO_MASTER_MAX_REG 32
|
|
-#define QCA8K_GOL_MAC_ADDR0 0x60
|
|
-#define QCA8K_GOL_MAC_ADDR1 0x64
|
|
-#define QCA8K_MAX_FRAME_SIZE 0x78
|
|
-#define QCA8K_REG_PORT_STATUS(_i) (0x07c + (_i) * 4)
|
|
-#define QCA8K_PORT_STATUS_SPEED GENMASK(1, 0)
|
|
-#define QCA8K_PORT_STATUS_SPEED_10 0
|
|
-#define QCA8K_PORT_STATUS_SPEED_100 0x1
|
|
-#define QCA8K_PORT_STATUS_SPEED_1000 0x2
|
|
-#define QCA8K_PORT_STATUS_TXMAC BIT(2)
|
|
-#define QCA8K_PORT_STATUS_RXMAC BIT(3)
|
|
-#define QCA8K_PORT_STATUS_TXFLOW BIT(4)
|
|
-#define QCA8K_PORT_STATUS_RXFLOW BIT(5)
|
|
-#define QCA8K_PORT_STATUS_DUPLEX BIT(6)
|
|
-#define QCA8K_PORT_STATUS_LINK_UP BIT(8)
|
|
-#define QCA8K_PORT_STATUS_LINK_AUTO BIT(9)
|
|
-#define QCA8K_PORT_STATUS_LINK_PAUSE BIT(10)
|
|
-#define QCA8K_PORT_STATUS_FLOW_AUTO BIT(12)
|
|
-#define QCA8K_REG_PORT_HDR_CTRL(_i) (0x9c + (_i * 4))
|
|
-#define QCA8K_PORT_HDR_CTRL_RX_MASK GENMASK(3, 2)
|
|
-#define QCA8K_PORT_HDR_CTRL_TX_MASK GENMASK(1, 0)
|
|
-#define QCA8K_PORT_HDR_CTRL_ALL 2
|
|
-#define QCA8K_PORT_HDR_CTRL_MGMT 1
|
|
-#define QCA8K_PORT_HDR_CTRL_NONE 0
|
|
-#define QCA8K_REG_SGMII_CTRL 0x0e0
|
|
-#define QCA8K_SGMII_EN_PLL BIT(1)
|
|
-#define QCA8K_SGMII_EN_RX BIT(2)
|
|
-#define QCA8K_SGMII_EN_TX BIT(3)
|
|
-#define QCA8K_SGMII_EN_SD BIT(4)
|
|
-#define QCA8K_SGMII_CLK125M_DELAY BIT(7)
|
|
-#define QCA8K_SGMII_MODE_CTRL_MASK GENMASK(23, 22)
|
|
-#define QCA8K_SGMII_MODE_CTRL(x) FIELD_PREP(QCA8K_SGMII_MODE_CTRL_MASK, x)
|
|
-#define QCA8K_SGMII_MODE_CTRL_BASEX QCA8K_SGMII_MODE_CTRL(0x0)
|
|
-#define QCA8K_SGMII_MODE_CTRL_PHY QCA8K_SGMII_MODE_CTRL(0x1)
|
|
-#define QCA8K_SGMII_MODE_CTRL_MAC QCA8K_SGMII_MODE_CTRL(0x2)
|
|
-
|
|
-/* MAC_PWR_SEL registers */
|
|
-#define QCA8K_REG_MAC_PWR_SEL 0x0e4
|
|
-#define QCA8K_MAC_PWR_RGMII1_1_8V BIT(18)
|
|
-#define QCA8K_MAC_PWR_RGMII0_1_8V BIT(19)
|
|
-
|
|
-/* EEE control registers */
|
|
-#define QCA8K_REG_EEE_CTRL 0x100
|
|
-#define QCA8K_REG_EEE_CTRL_LPI_EN(_i) ((_i + 1) * 2)
|
|
-
|
|
-/* TRUNK_HASH_EN registers */
|
|
-#define QCA8K_TRUNK_HASH_EN_CTRL 0x270
|
|
-#define QCA8K_TRUNK_HASH_SIP_EN BIT(3)
|
|
-#define QCA8K_TRUNK_HASH_DIP_EN BIT(2)
|
|
-#define QCA8K_TRUNK_HASH_SA_EN BIT(1)
|
|
-#define QCA8K_TRUNK_HASH_DA_EN BIT(0)
|
|
-#define QCA8K_TRUNK_HASH_MASK GENMASK(3, 0)
|
|
-
|
|
-/* ACL registers */
|
|
-#define QCA8K_REG_PORT_VLAN_CTRL0(_i) (0x420 + (_i * 8))
|
|
-#define QCA8K_PORT_VLAN_CVID_MASK GENMASK(27, 16)
|
|
-#define QCA8K_PORT_VLAN_CVID(x) FIELD_PREP(QCA8K_PORT_VLAN_CVID_MASK, x)
|
|
-#define QCA8K_PORT_VLAN_SVID_MASK GENMASK(11, 0)
|
|
-#define QCA8K_PORT_VLAN_SVID(x) FIELD_PREP(QCA8K_PORT_VLAN_SVID_MASK, x)
|
|
-#define QCA8K_REG_PORT_VLAN_CTRL1(_i) (0x424 + (_i * 8))
|
|
-#define QCA8K_REG_IPV4_PRI_BASE_ADDR 0x470
|
|
-#define QCA8K_REG_IPV4_PRI_ADDR_MASK 0x474
|
|
-
|
|
-/* Lookup registers */
|
|
-#define QCA8K_REG_ATU_DATA0 0x600
|
|
-#define QCA8K_ATU_ADDR2_MASK GENMASK(31, 24)
|
|
-#define QCA8K_ATU_ADDR3_MASK GENMASK(23, 16)
|
|
-#define QCA8K_ATU_ADDR4_MASK GENMASK(15, 8)
|
|
-#define QCA8K_ATU_ADDR5_MASK GENMASK(7, 0)
|
|
-#define QCA8K_REG_ATU_DATA1 0x604
|
|
-#define QCA8K_ATU_PORT_MASK GENMASK(22, 16)
|
|
-#define QCA8K_ATU_ADDR0_MASK GENMASK(15, 8)
|
|
-#define QCA8K_ATU_ADDR1_MASK GENMASK(7, 0)
|
|
-#define QCA8K_REG_ATU_DATA2 0x608
|
|
-#define QCA8K_ATU_VID_MASK GENMASK(19, 8)
|
|
-#define QCA8K_ATU_STATUS_MASK GENMASK(3, 0)
|
|
-#define QCA8K_ATU_STATUS_STATIC 0xf
|
|
-#define QCA8K_REG_ATU_FUNC 0x60c
|
|
-#define QCA8K_ATU_FUNC_BUSY BIT(31)
|
|
-#define QCA8K_ATU_FUNC_PORT_EN BIT(14)
|
|
-#define QCA8K_ATU_FUNC_MULTI_EN BIT(13)
|
|
-#define QCA8K_ATU_FUNC_FULL BIT(12)
|
|
-#define QCA8K_ATU_FUNC_PORT_MASK GENMASK(11, 8)
|
|
-#define QCA8K_REG_VTU_FUNC0 0x610
|
|
-#define QCA8K_VTU_FUNC0_VALID BIT(20)
|
|
-#define QCA8K_VTU_FUNC0_IVL_EN BIT(19)
|
|
-/* QCA8K_VTU_FUNC0_EG_MODE_MASK GENMASK(17, 4)
|
|
- * It does contain VLAN_MODE for each port [5:4] for port0,
|
|
- * [7:6] for port1 ... [17:16] for port6. Use virtual port
|
|
- * define to handle this.
|
|
- */
|
|
-#define QCA8K_VTU_FUNC0_EG_MODE_PORT_SHIFT(_i) (4 + (_i) * 2)
|
|
-#define QCA8K_VTU_FUNC0_EG_MODE_MASK GENMASK(1, 0)
|
|
-#define QCA8K_VTU_FUNC0_EG_MODE_PORT_MASK(_i) (GENMASK(1, 0) << QCA8K_VTU_FUNC0_EG_MODE_PORT_SHIFT(_i))
|
|
-#define QCA8K_VTU_FUNC0_EG_MODE_UNMOD FIELD_PREP(QCA8K_VTU_FUNC0_EG_MODE_MASK, 0x0)
|
|
-#define QCA8K_VTU_FUNC0_EG_MODE_PORT_UNMOD(_i) (QCA8K_VTU_FUNC0_EG_MODE_UNMOD << QCA8K_VTU_FUNC0_EG_MODE_PORT_SHIFT(_i))
|
|
-#define QCA8K_VTU_FUNC0_EG_MODE_UNTAG FIELD_PREP(QCA8K_VTU_FUNC0_EG_MODE_MASK, 0x1)
|
|
-#define QCA8K_VTU_FUNC0_EG_MODE_PORT_UNTAG(_i) (QCA8K_VTU_FUNC0_EG_MODE_UNTAG << QCA8K_VTU_FUNC0_EG_MODE_PORT_SHIFT(_i))
|
|
-#define QCA8K_VTU_FUNC0_EG_MODE_TAG FIELD_PREP(QCA8K_VTU_FUNC0_EG_MODE_MASK, 0x2)
|
|
-#define QCA8K_VTU_FUNC0_EG_MODE_PORT_TAG(_i) (QCA8K_VTU_FUNC0_EG_MODE_TAG << QCA8K_VTU_FUNC0_EG_MODE_PORT_SHIFT(_i))
|
|
-#define QCA8K_VTU_FUNC0_EG_MODE_NOT FIELD_PREP(QCA8K_VTU_FUNC0_EG_MODE_MASK, 0x3)
|
|
-#define QCA8K_VTU_FUNC0_EG_MODE_PORT_NOT(_i) (QCA8K_VTU_FUNC0_EG_MODE_NOT << QCA8K_VTU_FUNC0_EG_MODE_PORT_SHIFT(_i))
|
|
-#define QCA8K_REG_VTU_FUNC1 0x614
|
|
-#define QCA8K_VTU_FUNC1_BUSY BIT(31)
|
|
-#define QCA8K_VTU_FUNC1_VID_MASK GENMASK(27, 16)
|
|
-#define QCA8K_VTU_FUNC1_FULL BIT(4)
|
|
-#define QCA8K_REG_ATU_CTRL 0x618
|
|
-#define QCA8K_ATU_AGE_TIME_MASK GENMASK(15, 0)
|
|
-#define QCA8K_ATU_AGE_TIME(x) FIELD_PREP(QCA8K_ATU_AGE_TIME_MASK, (x))
|
|
-#define QCA8K_REG_GLOBAL_FW_CTRL0 0x620
|
|
-#define QCA8K_GLOBAL_FW_CTRL0_CPU_PORT_EN BIT(10)
|
|
-#define QCA8K_GLOBAL_FW_CTRL0_MIRROR_PORT_NUM GENMASK(7, 4)
|
|
-#define QCA8K_REG_GLOBAL_FW_CTRL1 0x624
|
|
-#define QCA8K_GLOBAL_FW_CTRL1_IGMP_DP_MASK GENMASK(30, 24)
|
|
-#define QCA8K_GLOBAL_FW_CTRL1_BC_DP_MASK GENMASK(22, 16)
|
|
-#define QCA8K_GLOBAL_FW_CTRL1_MC_DP_MASK GENMASK(14, 8)
|
|
-#define QCA8K_GLOBAL_FW_CTRL1_UC_DP_MASK GENMASK(6, 0)
|
|
-#define QCA8K_PORT_LOOKUP_CTRL(_i) (0x660 + (_i) * 0xc)
|
|
-#define QCA8K_PORT_LOOKUP_MEMBER GENMASK(6, 0)
|
|
-#define QCA8K_PORT_LOOKUP_VLAN_MODE_MASK GENMASK(9, 8)
|
|
-#define QCA8K_PORT_LOOKUP_VLAN_MODE(x) FIELD_PREP(QCA8K_PORT_LOOKUP_VLAN_MODE_MASK, x)
|
|
-#define QCA8K_PORT_LOOKUP_VLAN_MODE_NONE QCA8K_PORT_LOOKUP_VLAN_MODE(0x0)
|
|
-#define QCA8K_PORT_LOOKUP_VLAN_MODE_FALLBACK QCA8K_PORT_LOOKUP_VLAN_MODE(0x1)
|
|
-#define QCA8K_PORT_LOOKUP_VLAN_MODE_CHECK QCA8K_PORT_LOOKUP_VLAN_MODE(0x2)
|
|
-#define QCA8K_PORT_LOOKUP_VLAN_MODE_SECURE QCA8K_PORT_LOOKUP_VLAN_MODE(0x3)
|
|
-#define QCA8K_PORT_LOOKUP_STATE_MASK GENMASK(18, 16)
|
|
-#define QCA8K_PORT_LOOKUP_STATE(x) FIELD_PREP(QCA8K_PORT_LOOKUP_STATE_MASK, x)
|
|
-#define QCA8K_PORT_LOOKUP_STATE_DISABLED QCA8K_PORT_LOOKUP_STATE(0x0)
|
|
-#define QCA8K_PORT_LOOKUP_STATE_BLOCKING QCA8K_PORT_LOOKUP_STATE(0x1)
|
|
-#define QCA8K_PORT_LOOKUP_STATE_LISTENING QCA8K_PORT_LOOKUP_STATE(0x2)
|
|
-#define QCA8K_PORT_LOOKUP_STATE_LEARNING QCA8K_PORT_LOOKUP_STATE(0x3)
|
|
-#define QCA8K_PORT_LOOKUP_STATE_FORWARD QCA8K_PORT_LOOKUP_STATE(0x4)
|
|
-#define QCA8K_PORT_LOOKUP_LEARN BIT(20)
|
|
-#define QCA8K_PORT_LOOKUP_ING_MIRROR_EN BIT(25)
|
|
-
|
|
-#define QCA8K_REG_GOL_TRUNK_CTRL0 0x700
|
|
-/* 4 max trunk first
|
|
- * first 6 bit for member bitmap
|
|
- * 7th bit is to enable trunk port
|
|
- */
|
|
-#define QCA8K_REG_GOL_TRUNK_SHIFT(_i) ((_i) * 8)
|
|
-#define QCA8K_REG_GOL_TRUNK_EN_MASK BIT(7)
|
|
-#define QCA8K_REG_GOL_TRUNK_EN(_i) (QCA8K_REG_GOL_TRUNK_EN_MASK << QCA8K_REG_GOL_TRUNK_SHIFT(_i))
|
|
-#define QCA8K_REG_GOL_TRUNK_MEMBER_MASK GENMASK(6, 0)
|
|
-#define QCA8K_REG_GOL_TRUNK_MEMBER(_i) (QCA8K_REG_GOL_TRUNK_MEMBER_MASK << QCA8K_REG_GOL_TRUNK_SHIFT(_i))
|
|
-/* 0x704 for TRUNK 0-1 --- 0x708 for TRUNK 2-3 */
|
|
-#define QCA8K_REG_GOL_TRUNK_CTRL(_i) (0x704 + (((_i) / 2) * 4))
|
|
-#define QCA8K_REG_GOL_TRUNK_ID_MEM_ID_MASK GENMASK(3, 0)
|
|
-#define QCA8K_REG_GOL_TRUNK_ID_MEM_ID_EN_MASK BIT(3)
|
|
-#define QCA8K_REG_GOL_TRUNK_ID_MEM_ID_PORT_MASK GENMASK(2, 0)
|
|
-#define QCA8K_REG_GOL_TRUNK_ID_SHIFT(_i) (((_i) / 2) * 16)
|
|
-#define QCA8K_REG_GOL_MEM_ID_SHIFT(_i) ((_i) * 4)
|
|
-/* Complex shift: FIRST shift for port THEN shift for trunk */
|
|
-#define QCA8K_REG_GOL_TRUNK_ID_MEM_ID_SHIFT(_i, _j) (QCA8K_REG_GOL_MEM_ID_SHIFT(_j) + QCA8K_REG_GOL_TRUNK_ID_SHIFT(_i))
|
|
-#define QCA8K_REG_GOL_TRUNK_ID_MEM_ID_EN(_i, _j) (QCA8K_REG_GOL_TRUNK_ID_MEM_ID_EN_MASK << QCA8K_REG_GOL_TRUNK_ID_MEM_ID_SHIFT(_i, _j))
|
|
-#define QCA8K_REG_GOL_TRUNK_ID_MEM_ID_PORT(_i, _j) (QCA8K_REG_GOL_TRUNK_ID_MEM_ID_PORT_MASK << QCA8K_REG_GOL_TRUNK_ID_MEM_ID_SHIFT(_i, _j))
|
|
-
|
|
-#define QCA8K_REG_GLOBAL_FC_THRESH 0x800
|
|
-#define QCA8K_GLOBAL_FC_GOL_XON_THRES_MASK GENMASK(24, 16)
|
|
-#define QCA8K_GLOBAL_FC_GOL_XON_THRES(x) FIELD_PREP(QCA8K_GLOBAL_FC_GOL_XON_THRES_MASK, x)
|
|
-#define QCA8K_GLOBAL_FC_GOL_XOFF_THRES_MASK GENMASK(8, 0)
|
|
-#define QCA8K_GLOBAL_FC_GOL_XOFF_THRES(x) FIELD_PREP(QCA8K_GLOBAL_FC_GOL_XOFF_THRES_MASK, x)
|
|
-
|
|
-#define QCA8K_REG_PORT_HOL_CTRL0(_i) (0x970 + (_i) * 0x8)
|
|
-#define QCA8K_PORT_HOL_CTRL0_EG_PRI0_BUF_MASK GENMASK(3, 0)
|
|
-#define QCA8K_PORT_HOL_CTRL0_EG_PRI0(x) FIELD_PREP(QCA8K_PORT_HOL_CTRL0_EG_PRI0_BUF_MASK, x)
|
|
-#define QCA8K_PORT_HOL_CTRL0_EG_PRI1_BUF_MASK GENMASK(7, 4)
|
|
-#define QCA8K_PORT_HOL_CTRL0_EG_PRI1(x) FIELD_PREP(QCA8K_PORT_HOL_CTRL0_EG_PRI1_BUF_MASK, x)
|
|
-#define QCA8K_PORT_HOL_CTRL0_EG_PRI2_BUF_MASK GENMASK(11, 8)
|
|
-#define QCA8K_PORT_HOL_CTRL0_EG_PRI2(x) FIELD_PREP(QCA8K_PORT_HOL_CTRL0_EG_PRI2_BUF_MASK, x)
|
|
-#define QCA8K_PORT_HOL_CTRL0_EG_PRI3_BUF_MASK GENMASK(15, 12)
|
|
-#define QCA8K_PORT_HOL_CTRL0_EG_PRI3(x) FIELD_PREP(QCA8K_PORT_HOL_CTRL0_EG_PRI3_BUF_MASK, x)
|
|
-#define QCA8K_PORT_HOL_CTRL0_EG_PRI4_BUF_MASK GENMASK(19, 16)
|
|
-#define QCA8K_PORT_HOL_CTRL0_EG_PRI4(x) FIELD_PREP(QCA8K_PORT_HOL_CTRL0_EG_PRI4_BUF_MASK, x)
|
|
-#define QCA8K_PORT_HOL_CTRL0_EG_PRI5_BUF_MASK GENMASK(23, 20)
|
|
-#define QCA8K_PORT_HOL_CTRL0_EG_PRI5(x) FIELD_PREP(QCA8K_PORT_HOL_CTRL0_EG_PRI5_BUF_MASK, x)
|
|
-#define QCA8K_PORT_HOL_CTRL0_EG_PORT_BUF_MASK GENMASK(29, 24)
|
|
-#define QCA8K_PORT_HOL_CTRL0_EG_PORT(x) FIELD_PREP(QCA8K_PORT_HOL_CTRL0_EG_PORT_BUF_MASK, x)
|
|
-
|
|
-#define QCA8K_REG_PORT_HOL_CTRL1(_i) (0x974 + (_i) * 0x8)
|
|
-#define QCA8K_PORT_HOL_CTRL1_ING_BUF_MASK GENMASK(3, 0)
|
|
-#define QCA8K_PORT_HOL_CTRL1_ING(x) FIELD_PREP(QCA8K_PORT_HOL_CTRL1_ING_BUF_MASK, x)
|
|
-#define QCA8K_PORT_HOL_CTRL1_EG_PRI_BUF_EN BIT(6)
|
|
-#define QCA8K_PORT_HOL_CTRL1_EG_PORT_BUF_EN BIT(7)
|
|
-#define QCA8K_PORT_HOL_CTRL1_WRED_EN BIT(8)
|
|
-#define QCA8K_PORT_HOL_CTRL1_EG_MIRROR_EN BIT(16)
|
|
-
|
|
-/* Pkt edit registers */
|
|
-#define QCA8K_EGREES_VLAN_PORT_SHIFT(_i) (16 * ((_i) % 2))
|
|
-#define QCA8K_EGREES_VLAN_PORT_MASK(_i) (GENMASK(11, 0) << QCA8K_EGREES_VLAN_PORT_SHIFT(_i))
|
|
-#define QCA8K_EGREES_VLAN_PORT(_i, x) ((x) << QCA8K_EGREES_VLAN_PORT_SHIFT(_i))
|
|
-#define QCA8K_EGRESS_VLAN(x) (0x0c70 + (4 * (x / 2)))
|
|
-
|
|
-/* L3 registers */
|
|
-#define QCA8K_HROUTER_CONTROL 0xe00
|
|
-#define QCA8K_HROUTER_CONTROL_GLB_LOCKTIME_M GENMASK(17, 16)
|
|
-#define QCA8K_HROUTER_CONTROL_GLB_LOCKTIME_S 16
|
|
-#define QCA8K_HROUTER_CONTROL_ARP_AGE_MODE 1
|
|
-#define QCA8K_HROUTER_PBASED_CONTROL1 0xe08
|
|
-#define QCA8K_HROUTER_PBASED_CONTROL2 0xe0c
|
|
-#define QCA8K_HNAT_CONTROL 0xe38
|
|
-
|
|
-/* MIB registers */
|
|
-#define QCA8K_PORT_MIB_COUNTER(_i) (0x1000 + (_i) * 0x100)
|
|
-
|
|
-/* QCA specific MII registers */
|
|
-#define MII_ATH_MMD_ADDR 0x0d
|
|
-#define MII_ATH_MMD_DATA 0x0e
|
|
-
|
|
-enum {
|
|
- QCA8K_PORT_SPEED_10M = 0,
|
|
- QCA8K_PORT_SPEED_100M = 1,
|
|
- QCA8K_PORT_SPEED_1000M = 2,
|
|
- QCA8K_PORT_SPEED_ERR = 3,
|
|
-};
|
|
-
|
|
-enum qca8k_fdb_cmd {
|
|
- QCA8K_FDB_FLUSH = 1,
|
|
- QCA8K_FDB_LOAD = 2,
|
|
- QCA8K_FDB_PURGE = 3,
|
|
- QCA8K_FDB_FLUSH_PORT = 5,
|
|
- QCA8K_FDB_NEXT = 6,
|
|
- QCA8K_FDB_SEARCH = 7,
|
|
-};
|
|
-
|
|
-enum qca8k_vlan_cmd {
|
|
- QCA8K_VLAN_FLUSH = 1,
|
|
- QCA8K_VLAN_LOAD = 2,
|
|
- QCA8K_VLAN_PURGE = 3,
|
|
- QCA8K_VLAN_REMOVE_PORT = 4,
|
|
- QCA8K_VLAN_NEXT = 5,
|
|
- QCA8K_VLAN_READ = 6,
|
|
-};
|
|
-
|
|
-enum qca8k_mid_cmd {
|
|
- QCA8K_MIB_FLUSH = 1,
|
|
- QCA8K_MIB_FLUSH_PORT = 2,
|
|
- QCA8K_MIB_CAST = 3,
|
|
-};
|
|
-
|
|
-struct qca8k_match_data {
|
|
- u8 id;
|
|
- bool reduced_package;
|
|
- u8 mib_count;
|
|
-};
|
|
-
|
|
-enum {
|
|
- QCA8K_CPU_PORT0,
|
|
- QCA8K_CPU_PORT6,
|
|
-};
|
|
-
|
|
-struct qca8k_mgmt_eth_data {
|
|
- struct completion rw_done;
|
|
- struct mutex mutex; /* Enforce one mdio read/write at time */
|
|
- bool ack;
|
|
- u32 seq;
|
|
- u32 data[4];
|
|
-};
|
|
-
|
|
-struct qca8k_mib_eth_data {
|
|
- struct completion rw_done;
|
|
- struct mutex mutex; /* Process one command at time */
|
|
- refcount_t port_parsed; /* Counter to track parsed port */
|
|
- u8 req_port;
|
|
- u64 *data; /* pointer to ethtool data */
|
|
-};
|
|
-
|
|
-struct qca8k_ports_config {
|
|
- bool sgmii_rx_clk_falling_edge;
|
|
- bool sgmii_tx_clk_falling_edge;
|
|
- bool sgmii_enable_pll;
|
|
- u8 rgmii_rx_delay[QCA8K_NUM_CPU_PORTS]; /* 0: CPU port0, 1: CPU port6 */
|
|
- u8 rgmii_tx_delay[QCA8K_NUM_CPU_PORTS]; /* 0: CPU port0, 1: CPU port6 */
|
|
-};
|
|
-
|
|
-struct qca8k_mdio_cache {
|
|
-/* The 32bit switch registers are accessed indirectly. To achieve this we need
|
|
- * to set the page of the register. Track the last page that was set to reduce
|
|
- * mdio writes
|
|
- */
|
|
- u16 page;
|
|
-/* lo and hi can also be cached and from Documentation we can skip one
|
|
- * extra mdio write if lo or hi is didn't change.
|
|
- */
|
|
- u16 lo;
|
|
- u16 hi;
|
|
-};
|
|
-
|
|
-struct qca8k_priv {
|
|
- u8 switch_id;
|
|
- u8 switch_revision;
|
|
- u8 mirror_rx;
|
|
- u8 mirror_tx;
|
|
- u8 lag_hash_mode;
|
|
- /* Each bit correspond to a port. This switch can support a max of 7 port.
|
|
- * Bit 1: port enabled. Bit 0: port disabled.
|
|
- */
|
|
- u8 port_enabled_map;
|
|
- struct qca8k_ports_config ports_config;
|
|
- struct regmap *regmap;
|
|
- struct mii_bus *bus;
|
|
- struct dsa_switch *ds;
|
|
- struct mutex reg_mutex;
|
|
- struct device *dev;
|
|
- struct gpio_desc *reset_gpio;
|
|
- struct net_device *mgmt_master; /* Track if mdio/mib Ethernet is available */
|
|
- struct qca8k_mgmt_eth_data mgmt_eth_data;
|
|
- struct qca8k_mib_eth_data mib_eth_data;
|
|
- struct qca8k_mdio_cache mdio_cache;
|
|
-};
|
|
-
|
|
-struct qca8k_mib_desc {
|
|
- unsigned int size;
|
|
- unsigned int offset;
|
|
- const char *name;
|
|
-};
|
|
-
|
|
-struct qca8k_fdb {
|
|
- u16 vid;
|
|
- u8 port_mask;
|
|
- u8 aging;
|
|
- u8 mac[6];
|
|
-};
|
|
-
|
|
-#endif /* __QCA8K_H */
|