forked from Openwrt/openwrt
8c405cdccc
The patches were generated from the RPi repo with the following command: git format-patch v6.6.34..rpi-6.1.y Some patches needed rebasing and, as usual, the applied and reverted, wireless drivers, Github workflows, READMEs and defconfigs patches were removed. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
67 lines
2.2 KiB
Diff
67 lines
2.2 KiB
Diff
From 53c9d470fc7af24296f4c071d729bc413a00082e Mon Sep 17 00:00:00 2001
|
|
From: Markus Proeller <markus.proeller@pieye.org>
|
|
Date: Thu, 10 Oct 2019 19:12:08 +0200
|
|
Subject: [PATCH 0181/1085] dt-bindings: Add binding for the Infineon IRS1125
|
|
sensor
|
|
|
|
Adds a binding for the Infineon IRS1125 time-of-flight depth
|
|
sensor.
|
|
|
|
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
|
|
---
|
|
.../devicetree/bindings/media/i2c/irs1125.txt | 48 +++++++++++++++++++
|
|
1 file changed, 48 insertions(+)
|
|
create mode 100644 Documentation/devicetree/bindings/media/i2c/irs1125.txt
|
|
|
|
--- /dev/null
|
|
+++ b/Documentation/devicetree/bindings/media/i2c/irs1125.txt
|
|
@@ -0,0 +1,48 @@
|
|
+* Infineon irs1125 time of flight sensor
|
|
+
|
|
+The Infineon irs1125 is a time of flight digital image sensor with
|
|
+an active array size of 352H x 286V. It is programmable through I2C
|
|
+interface. The I2C address defaults to 0x3D, but can be reconfigured
|
|
+to address 0x3C or 0x41 via I2C commands. Image data is sent through
|
|
+MIPI CSI-2, which is configured as either 1 or 2 data lanes.
|
|
+
|
|
+Required Properties:
|
|
+- compatible: value should be "infineon,irs1125" for irs1125 sensor
|
|
+- reg: I2C bus address of the device
|
|
+- clocks: reference to the xclk input clock.
|
|
+- pwdn-gpios: reference to the GPIO connected to the reset pin.
|
|
+ This is an active low signal to the iirs1125.
|
|
+
|
|
+The irs1125 device node should contain one 'port' child node with
|
|
+an 'endpoint' subnode. For further reading on port node refer to
|
|
+Documentation/devicetree/bindings/media/video-interfaces.txt.
|
|
+
|
|
+Endpoint node required properties for CSI-2 connection are:
|
|
+- remote-endpoint: a phandle to the bus receiver's endpoint node.
|
|
+- clock-lanes: should be set to <0> (clock lane on hardware lane 0)
|
|
+- data-lanes: should be set to <1> or <1 2> (one or two lane CSI-2
|
|
+ supported)
|
|
+
|
|
+Example:
|
|
+ sensor@10 {
|
|
+ compatible = "infineon,irs1125";
|
|
+ reg = <0x3D>;
|
|
+ #address-cells = <1>;
|
|
+ #size-cells = <0>;
|
|
+ clocks = <&irs1125_clk>;
|
|
+ pwdn-gpios = <&gpio 5 0>;
|
|
+
|
|
+ irs1125_clk: camera-clk {
|
|
+ compatible = "fixed-clock";
|
|
+ #clock-cells = <0>;
|
|
+ clock-frequency = <26000000>;
|
|
+ };
|
|
+
|
|
+ port {
|
|
+ sensor_out: endpoint {
|
|
+ remote-endpoint = <&csiss_in>;
|
|
+ clock-lanes = <0>;
|
|
+ data-lanes = <1 2>;
|
|
+ };
|
|
+ };
|
|
+ };
|