forked from Openwrt/openwrt
c5b7ec8cee
Hardware:
SoC: Qualcomm Atheros QCA956X ver 1 rev 0
CPU clock: 775.000 MHz
Memory: 128 MB DDR2
Flash: 32 MB SPI NOR mx25l25635e
Switch: Atheros AR8327 rev. 4
Ethernet: 5x 10/100/1000 Mbps (1 WAN + 4 LAN)
Buttons: 1x Reset
Serial: TX, RX, GND, VCC
Baudrate: 115200
Wifi: Qualcomm Atheros qca988x 802.11ac/n - 3x3
Qualcomm Atheros AR9561 802.11b/g/n - 3x3
Not working:
Leds: 1x via a SPI controller
Display: ST7789V or ILI9341V
controlled by stm32f205.
Note:
DSA changes are ready, but we have an issue with
ports not working after 20-30 minutes. So for now
we use swconfig.
Installation: serial connection only
There is a J11 four pin connector. You need to connect TX, RX and GND.
You can find very good information about the device here
https://github.com/alexanderhenne/AFi-R?tab=readme-ov-file#finding-j11
Upgrading via serial port:
1. Download the kernel initramfs image. Copy the image to a TFTP server
2. Connect to console on the AP, and connect the LAN1 port to your PC LAN
3. Stop autoboot to get to U-boot shell
Interrupt the autoboot process by pressing any key when prompted
4. Transfer the kernel image with TFTP
Set your ip address on your TFTP server to 192.168.1.254
# tftpboot 0x81000000 amplifi-router-hd-initramfs-kernel.bin
5. Load the image
# bootm 0x81000000
6. SCP sysupgrade image from your PC to the Amplifi HD
(If you use a newer mac use scp -O)
# scp openwrt-ath79-generic-ubnt_amplifi-router-hd-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Write sysupgrade to the firmware partition
# mtd write /tmp/openwrt-ath79-generic-ubnt_amplifi-router-hd-squashfs-sysupgrade.bin firmware
8. Reboot your device
# reboot
Credit to alexanderhenne for all the information.
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
333 lines
9.1 KiB
Makefile
333 lines
9.1 KiB
Makefile
include ./common-ubnt.mk
|
|
|
|
define Device/ubnt_aircube-ac
|
|
$(Device/ubnt-acb)
|
|
SOC := ar9342
|
|
DEVICE_MODEL := airCube AC
|
|
UBNT_CHIP := ar9342
|
|
DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct
|
|
endef
|
|
TARGET_DEVICES += ubnt_aircube-ac
|
|
|
|
define Device/ubnt_aircube-isp
|
|
$(Device/ubnt-acb)
|
|
SOC := qca9533
|
|
DEVICE_MODEL := airCube ISP
|
|
UBNT_CHIP := qca9533
|
|
SUPPORTED_DEVICES += ubnt,acb-isp
|
|
endef
|
|
TARGET_DEVICES += ubnt_aircube-isp
|
|
|
|
define Device/ubnt_amplifi-router-hd
|
|
IMAGE_SIZE := 11264k
|
|
UBNT_BOARD := AFi-R-HD
|
|
UBNT_TYPE := AFi-R
|
|
UBNT_VERSION := 3.6.3
|
|
SOC := qca9563
|
|
DEVICE_MODEL := AmpliFi Router HD
|
|
UBNT_CHIP := qca956x
|
|
DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct kmod-usb2
|
|
endef
|
|
TARGET_DEVICES += ubnt_amplifi-router-hd
|
|
|
|
define Device/ubnt_bullet-ac
|
|
$(Device/ubnt-2wa)
|
|
DEVICE_MODEL := Bullet AC
|
|
DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct rssileds
|
|
endef
|
|
TARGET_DEVICES += ubnt_bullet-ac
|
|
|
|
define Device/ubnt_bullet-m-xw
|
|
$(Device/ubnt-xw)
|
|
DEVICE_MODEL := Bullet M
|
|
DEVICE_ALT0_VENDOR := Ubiquiti
|
|
DEVICE_ALT0_MODEL := Rocket M
|
|
DEVICE_ALT0_VARIANT := XW
|
|
DEVICE_PACKAGES += rssileds
|
|
SUPPORTED_DEVICES += bullet-m-xw
|
|
endef
|
|
TARGET_DEVICES += ubnt_bullet-m-xw
|
|
|
|
define Device/ubnt_edgeswitch-5xp
|
|
$(Device/ubnt-sw)
|
|
DEVICE_MODEL := EdgeSwitch 5XP
|
|
endef
|
|
TARGET_DEVICES += ubnt_edgeswitch-5xp
|
|
|
|
define Device/ubnt_edgeswitch-8xp
|
|
$(Device/ubnt-sw)
|
|
DEVICE_MODEL := EdgeSwitch 8XP
|
|
DEVICE_PACKAGES += kmod-switch-bcm53xx-mdio
|
|
DEFAULT := n
|
|
endef
|
|
TARGET_DEVICES += ubnt_edgeswitch-8xp
|
|
|
|
define Device/ubnt_lap-120
|
|
$(Device/ubnt-wa)
|
|
DEVICE_MODEL := LiteAP ac (LAP-120)
|
|
DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct
|
|
endef
|
|
TARGET_DEVICES += ubnt_lap-120
|
|
|
|
define Device/ubnt_litebeam-ac-gen2
|
|
$(Device/ubnt-wa)
|
|
DEVICE_MODEL := LiteBeam AC
|
|
DEVICE_VARIANT := Gen2
|
|
DEVICE_PACKAGES := kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct
|
|
endef
|
|
TARGET_DEVICES += ubnt_litebeam-ac-gen2
|
|
|
|
define Device/ubnt_litebeam-m5-xw
|
|
$(Device/ubnt-xw)
|
|
DEVICE_MODEL := LiteBeam M5
|
|
SUPPORTED_DEVICES += lbe-m5
|
|
DEVICE_PACKAGES := -kmod-usb2
|
|
endef
|
|
TARGET_DEVICES += ubnt_litebeam-m5-xw
|
|
|
|
define Device/ubnt_nanobeam-ac
|
|
$(Device/ubnt-wa)
|
|
DEVICE_MODEL := NanoBeam AC
|
|
DEVICE_VARIANT := Gen1
|
|
DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct rssileds
|
|
endef
|
|
TARGET_DEVICES += ubnt_nanobeam-ac
|
|
|
|
define Device/ubnt_nanobeam-ac-gen2
|
|
$(Device/ubnt-wa)
|
|
DEVICE_MODEL := NanoBeam AC
|
|
DEVICE_VARIANT := Gen2
|
|
DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct rssileds
|
|
endef
|
|
TARGET_DEVICES += ubnt_nanobeam-ac-gen2
|
|
|
|
define Device/ubnt_nanobeam-ac-xc
|
|
$(Device/ubnt-xc)
|
|
SOC := qca9558
|
|
DEVICE_MODEL := NanoBeam AC
|
|
DEVICE_VARIANT := Gen1 (XC)
|
|
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct rssileds
|
|
endef
|
|
TARGET_DEVICES += ubnt_nanobeam-ac-xc
|
|
|
|
define Device/ubnt_nanostation-ac
|
|
$(Device/ubnt-wa)
|
|
DEVICE_MODEL := Nanostation AC
|
|
DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct rssileds
|
|
endef
|
|
TARGET_DEVICES += ubnt_nanostation-ac
|
|
|
|
define Device/ubnt_nanostation-ac-loco
|
|
$(Device/ubnt-wa)
|
|
DEVICE_MODEL := Nanostation AC loco
|
|
DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct
|
|
endef
|
|
TARGET_DEVICES += ubnt_nanostation-ac-loco
|
|
|
|
define Device/ubnt_nanostation-loco-m-xw
|
|
$(Device/ubnt-xw)
|
|
DEVICE_MODEL := Nanostation Loco M
|
|
DEVICE_PACKAGES += rssileds -kmod-usb2
|
|
DEVICE_ALT0_VENDOR := Ubiquiti
|
|
DEVICE_ALT0_MODEL := AirGrid M5 HP
|
|
DEVICE_ALT0_VARIANT := XW
|
|
DEVICE_ALT1_VENDOR := Ubiquiti
|
|
DEVICE_ALT1_MODEL := PowerBeam M5 300
|
|
DEVICE_ALT1_VARIANT := XW
|
|
DEVICE_ALT2_VENDOR := Ubiquiti
|
|
DEVICE_ALT2_MODEL := NanoBeam M5
|
|
DEVICE_ALT2_VARIANT := XW
|
|
SUPPORTED_DEVICES += loco-m-xw nanostation-m-xw ubnt,nanobeam-m5-xw
|
|
endef
|
|
TARGET_DEVICES += ubnt_nanostation-loco-m-xw
|
|
|
|
define Device/ubnt_nanostation-m-xw
|
|
$(Device/ubnt-xw)
|
|
DEVICE_MODEL := Nanostation M
|
|
DEVICE_PACKAGES += rssileds
|
|
SUPPORTED_DEVICES += nanostation-m-xw
|
|
endef
|
|
TARGET_DEVICES += ubnt_nanostation-m-xw
|
|
|
|
define Device/ubnt_powerbeam-5ac-500
|
|
$(Device/ubnt-xc)
|
|
SOC := qca9558
|
|
DEVICE_MODEL := PowerBeam 5AC
|
|
DEVICE_VARIANT := 500
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
endef
|
|
TARGET_DEVICES += ubnt_powerbeam-5ac-500
|
|
|
|
define Device/ubnt_powerbeam-5ac-gen2
|
|
$(Device/ubnt-wa)
|
|
DEVICE_MODEL := PowerBeam 5AC
|
|
DEVICE_VARIANT := Gen2
|
|
DEVICE_PACKAGES := kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct rssileds
|
|
endef
|
|
TARGET_DEVICES += ubnt_powerbeam-5ac-gen2
|
|
|
|
define Device/ubnt_powerbeam-m2-xw
|
|
$(Device/ubnt-xw)
|
|
DEVICE_MODEL := PowerBeam M2
|
|
DEVICE_PACKAGES += rssileds
|
|
SUPPORTED_DEVICES += loco-m-xw
|
|
endef
|
|
TARGET_DEVICES += ubnt_powerbeam-m2-xw
|
|
|
|
define Device/ubnt_powerbeam-m5-xw
|
|
$(Device/ubnt-xw)
|
|
DEVICE_MODEL := PowerBeam M5
|
|
DEVICE_PACKAGES += rssileds
|
|
SUPPORTED_DEVICES += loco-m-xw
|
|
endef
|
|
TARGET_DEVICES += ubnt_powerbeam-m5-xw
|
|
|
|
define Device/ubnt_powerbridge-m
|
|
$(Device/ubnt-xm)
|
|
SOC := ar7241
|
|
DEVICE_MODEL := PowerBridge M
|
|
DEVICE_PACKAGES += rssileds
|
|
SUPPORTED_DEVICES += bullet-m
|
|
endef
|
|
TARGET_DEVICES += ubnt_powerbridge-m
|
|
|
|
define Device/ubnt_rocket-5ac-lite
|
|
$(Device/ubnt-xc)
|
|
SOC := qca9558
|
|
DEVICE_MODEL := Rocket 5AC
|
|
DEVICE_VARIANT := Lite
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
endef
|
|
TARGET_DEVICES += ubnt_rocket-5ac-lite
|
|
|
|
define Device/ubnt_rocket-m
|
|
$(Device/ubnt-xm)
|
|
SOC := ar7241
|
|
DEVICE_MODEL := Rocket M
|
|
DEVICE_PACKAGES += rssileds
|
|
SUPPORTED_DEVICES += rocket-m
|
|
endef
|
|
TARGET_DEVICES += ubnt_rocket-m
|
|
|
|
define Device/ubnt_routerstation_common
|
|
DEVICE_PACKAGES := -kmod-ath9k -wpad-basic-mbedtls -uboot-envtools kmod-usb-ohci \
|
|
kmod-usb2 fconfig
|
|
DEVICE_VENDOR := Ubiquiti
|
|
SOC := ar7161
|
|
LOADER_TYPE := bin
|
|
LOADER_FLASH_OFFS := 0x50000
|
|
COMPILE := loader-$(1).bin
|
|
COMPILE/loader-$(1).bin := loader-okli-compile | lzma | pad-to 128k
|
|
IMAGE_SIZE := 16000k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | uImage lzma -M 0x4f4b4c49 | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | pad-to $$$$(BLOCKSIZE) | \
|
|
mkubntimage $$$$(KDIR)/loader-$(1).bin | check-size
|
|
IMAGE/sysupgrade.bin := append-kernel | uImage lzma -M 0x4f4b4c49 | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | pad-to $$$$(BLOCKSIZE) | check-size | \
|
|
sysupgrade-tar kernel=$$$$(KDIR)/loader-$(1).bin rootfs=$$$$@ | append-metadata
|
|
KERNEL := kernel-bin | append-dtb | lzma
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb
|
|
DEVICE_COMPAT_VERSION := 2.0
|
|
DEVICE_COMPAT_MESSAGE := Partition design has changed compared to older versions (19.07 and 21.02) \
|
|
due to kernel drivers restrictions. Upgrade via sysupgrade mechanism is one way operation. \
|
|
Downgrading OpenWrt version will involve usage of TFTP recovery or bootloader command line interface.
|
|
endef
|
|
|
|
define Device/ubnt_routerstation
|
|
$(Device/ubnt_routerstation_common)
|
|
DEVICE_MODEL := RouterStation
|
|
UBNT_BOARD := RS
|
|
UBNT_TYPE := RSx
|
|
UBNT_CHIP := ar7100
|
|
DEVICE_PACKAGES += -swconfig
|
|
endef
|
|
TARGET_DEVICES += ubnt_routerstation
|
|
|
|
define Device/ubnt_routerstation-pro
|
|
$(Device/ubnt_routerstation_common)
|
|
DEVICE_MODEL := RouterStation Pro
|
|
UBNT_BOARD := RSPRO
|
|
UBNT_TYPE := RSPRO
|
|
UBNT_CHIP := ar7100pro
|
|
endef
|
|
TARGET_DEVICES += ubnt_routerstation-pro
|
|
|
|
define Device/ubnt_uk-ultra
|
|
$(Device/ubnt_unifiac)
|
|
DEVICE_MODEL := UniFi Swiss Army Knife Ultra
|
|
DEVICE_PACKAGES += rssileds -swconfig
|
|
endef
|
|
TARGET_DEVICES += ubnt_uk-ultra
|
|
|
|
define Device/ubnt_unifi-ap
|
|
$(Device/ubnt-bz)
|
|
DEVICE_MODEL := UniFi AP
|
|
SUPPORTED_DEVICES += unifi ubnt,unifi
|
|
endef
|
|
TARGET_DEVICES += ubnt_unifi-ap
|
|
|
|
define Device/ubnt_unifi-ap-lr
|
|
$(Device/ubnt-bz)
|
|
DEVICE_MODEL := UniFi AP
|
|
DEVICE_VARIANT := LR
|
|
SUPPORTED_DEVICES += unifi ubnt,unifi ubnt,unifi-ap
|
|
endef
|
|
TARGET_DEVICES += ubnt_unifi-ap-lr
|
|
|
|
define Device/ubnt_unifiac-lite
|
|
$(Device/ubnt_unifiac)
|
|
DEVICE_MODEL := UniFi AC Lite
|
|
DEVICE_PACKAGES += -swconfig
|
|
SUPPORTED_DEVICES += unifiac-lite
|
|
endef
|
|
TARGET_DEVICES += ubnt_unifiac-lite
|
|
|
|
define Device/ubnt_unifiac-lr
|
|
$(Device/ubnt_unifiac)
|
|
DEVICE_MODEL := UniFi AC LR
|
|
DEVICE_PACKAGES += -swconfig
|
|
SUPPORTED_DEVICES += unifiac-lite ubnt,unifiac-lite
|
|
endef
|
|
TARGET_DEVICES += ubnt_unifiac-lr
|
|
|
|
define Device/ubnt_unifiac-mesh
|
|
$(Device/ubnt_unifiac)
|
|
DEVICE_MODEL := UniFi AC Mesh
|
|
DEVICE_PACKAGES += -swconfig
|
|
SUPPORTED_DEVICES += unifiac-lite
|
|
endef
|
|
TARGET_DEVICES += ubnt_unifiac-mesh
|
|
|
|
define Device/ubnt_unifiac-mesh-pro
|
|
$(Device/ubnt_unifiac)
|
|
DEVICE_MODEL := UniFi AC Mesh Pro
|
|
SUPPORTED_DEVICES += unifiac-pro
|
|
endef
|
|
TARGET_DEVICES += ubnt_unifiac-mesh-pro
|
|
|
|
define Device/ubnt_unifiac-pro
|
|
$(Device/ubnt_unifiac)
|
|
DEVICE_MODEL := UniFi AC Pro
|
|
DEVICE_PACKAGES += kmod-usb2
|
|
SUPPORTED_DEVICES += unifiac-pro
|
|
endef
|
|
TARGET_DEVICES += ubnt_unifiac-pro
|
|
|
|
define Device/ubnt_unifi-ap-outdoor-plus
|
|
$(Device/ubnt-bz)
|
|
$(Device/ubnt-unifi-jffs2)
|
|
DEVICE_MODEL := UniFi AP Outdoor+
|
|
SUPPORTED_DEVICES += unifi-outdoor-plus
|
|
endef
|
|
TARGET_DEVICES += ubnt_unifi-ap-outdoor-plus
|
|
|
|
define Device/ubnt_unifi-ap-pro
|
|
$(Device/ubnt-unifi-jffs2)
|
|
SOC := ar9344
|
|
DEVICE_MODEL := UniFi AP Pro
|
|
UBNT_CHIP := ar934x
|
|
SUPPORTED_DEVICES += uap-pro
|
|
endef
|
|
TARGET_DEVICES += ubnt_unifi-ap-pro
|