forked from Openwrt/openwrt
e3ddfcc70c
Initial conversion to new LED color/function format and drop label format where possible. The same label is composed at runtime. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
183 lines
3.2 KiB
Plaintext
183 lines
3.2 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "ar9344.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/leds/common.h>
|
|
#include <dt-bindings/mtd/partitions/uimage.h>
|
|
|
|
/ {
|
|
aliases {
|
|
led-boot = &power_green;
|
|
led-failsafe = &power_red;
|
|
led-running = &power_green;
|
|
led-upgrade = &power_red;
|
|
};
|
|
|
|
firmware-concat {
|
|
compatible = "mtd-concat";
|
|
devices = <&fwconcat0 &fwconcat1>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
reg = <0x0 0x1f00000>;
|
|
label = "firmware";
|
|
compatible = "openwrt,uimage", "denx,uimage";
|
|
};
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
linux,code = <KEY_RESTART>;
|
|
label = "Reset button";
|
|
gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
|
|
debounce-interval = <50>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&enable_gpio_11>,
|
|
<&enable_gpio_16>,
|
|
<&enable_gpio_4>,
|
|
<&clks_disable_pins>;
|
|
|
|
power_green: power-green {
|
|
function = LED_FUNCTION_POWER;
|
|
color = <LED_COLOR_ID_GREEN>;
|
|
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
|
default-state = "on";
|
|
};
|
|
};
|
|
|
|
reserved-memory {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges;
|
|
|
|
ruckus-himem@7ff0000 {
|
|
/* Ruckus Himem area used to control
|
|
* redundant boot image selection
|
|
*/
|
|
compatible = "nvmem-rmem";
|
|
reg = <0x7ff0000 0x10000>;
|
|
no-map;
|
|
};
|
|
};
|
|
};
|
|
|
|
&ref {
|
|
clock-frequency = <40000000>;
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x040000>;
|
|
read-only;
|
|
};
|
|
|
|
fwconcat0: partition@40000 {
|
|
label = "fwconcat0";
|
|
reg = <0x040000 0xf00000>;
|
|
};
|
|
|
|
partition@f40000 {
|
|
compatible = "u-boot,env";
|
|
label = "u-boot-env";
|
|
reg = <0xf40000 0x040000>;
|
|
};
|
|
|
|
board_data: partition@f80000 {
|
|
label = "board-data";
|
|
reg = <0xf80000 0x080000>;
|
|
read-only;
|
|
};
|
|
|
|
fwconcat1: partition@1000000 {
|
|
label = "fwconcat1";
|
|
reg = <0x1000000 0x1000000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy: ethernet-phy@6 {
|
|
compatible = "ethernet-phy-ieee802.3-c22";
|
|
reg = <6>;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
pll-data = <0x02000000 0x00000101 0x00001313>;
|
|
phy-mode = "rgmii-id";
|
|
phy-handle = <&phy>;
|
|
|
|
nvmem-cell-names = "mac-address";
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
rgmii-gmac0 = <1>;
|
|
rxdv-delay = <3>;
|
|
rxd-delay = <3>;
|
|
};
|
|
};
|
|
|
|
&pinmux {
|
|
clks_disable_pins: pinmux_clks_disable_pins {
|
|
pinctrl-single,bits = <0x40 0x0 0x20>;
|
|
};
|
|
|
|
enable_gpio_4: pinctrl_enable_gpio_4 {
|
|
pinctrl-single,bits = <0x4 0x0 0xff>;
|
|
};
|
|
|
|
enable_gpio_11: pinctrl_enable_gpio_11 {
|
|
pinctrl-single,bits = <0x8 0x0 0xff000000>;
|
|
};
|
|
|
|
enable_gpio_16: pinctrl_enable_gpio_16 {
|
|
pinctrl-single,bits = <0x10 0x0 0xff>;
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
nvmem-cells = <&macaddr_board_data_60>, <&cal_board_data_41000>;
|
|
nvmem-cell-names = "mac-address", "calibration";
|
|
};
|
|
|
|
&usb {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_phy {
|
|
status = "okay";
|
|
};
|