Openwrt/msm8916-openwrt
1
0
Fork 0
forked from Openwrt/openwrt
Code Issues 1 Pull Requests Actions Activity
msm8916
msm8916-openwrt/package/boot/uboot-kirkwood/patches/008-nsa325-uboot-generic.patch
Pawel Dembicki 6cafea5c5e uboot-kirkwood: update to 2020.04 
Update U-Boot to current 2020.04 release for kirkwood platform.

Catch up with upstream and move some configuration options from
the header files to the corresponding defconfig files.

Compile tested: all devices
Run tested: nsa310, pogoplugv4

Tested-by: Cezary Jackiewicz <cezary@eko.one.pl> [nsa310]
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-04-20 16:37:56 +02:00

650 lines
19 KiB
Diff
Raw Permalink Blame History

--- a/arch/arm/mach-kirkwood/Kconfig
+++ b/arch/arm/mach-kirkwood/Kconfig
@@ -68,6 +68,9 @@ config TARGET_SBx81LIFXCAT
config TARGET_DB_88F6281_BP
bool "Marvell DB-88F6281-BP"
+config TARGET_NSA325
+ bool "Zyxel NSA325 board"
+
endchoice
config SYS_SOC
@@ -91,6 +94,7 @@ source "board/Seagate/goflexhome/Kconfig
source "board/Seagate/nas220/Kconfig"
source "board/zyxel/nsa310/Kconfig"
source "board/zyxel/nsa310s/Kconfig"
+source "board/zyxel/nsa325/Kconfig"
source "board/alliedtelesis/SBx81LIFKW/Kconfig"
source "board/alliedtelesis/SBx81LIFXCAT/Kconfig"
source "board/Marvell/db-88f6281-bp/Kconfig"
--- /dev/null
+++ b/board/zyxel/nsa325/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_NSA325
+
+config SYS_BOARD
+ default "nsa325"
+
+config SYS_VENDOR
+ default "zyxel"
+
+config SYS_CONFIG_NAME
+ default "nsa325"
+
+endif
--- /dev/null
+++ b/board/zyxel/nsa325/MAINTAINERS
@@ -0,0 +1,6 @@
+NSA325 BOARD
+M: Alberto Bursi <alberto.bursi@outlook.it>
+S: Maintained
+F: board/zyxel/nsa325/
+F: include/configs/nsa325.h
+F: configs/nsa325_defconfig
--- /dev/null
+++ b/board/zyxel/nsa325/Makefile
@@ -0,0 +1,13 @@
+#
+# (C) Copyright 2015 bodhi <mibodhi@gmail.com>
+#
+# Based on
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := nsa325.o
+
--- /dev/null
+++ b/board/zyxel/nsa325/kwbimage.cfg
@@ -0,0 +1,78 @@
+# Copyright (C) 2015 bodhi <mibodhi@gmail.com>
+#
+# Extracted from Zyxel GPL source for u-boot-1.1.4_NSA325v2
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+#BOOT_FROM uart
+BOOT_FROM nand
+NAND_ECC_MODE default
+NAND_PAGE_SIZE 0x0800
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+
+# Configure RGMII-0 interface pad voltage to 1.8V
+DATA 0xFFD100e0 0x1b1b1b9b
+
+#Dram initalization
+DATA 0xFFD01400 0x4301503E # DDR Configuration register
+DATA 0xFFD01404 0xB9843000 # DDR Controller Control Low
+DATA 0xFFD01408 0x33137777 # DDR Timing (Low)
+DATA 0xFFD0140C 0x16000C55 # DDR Timing (High)
+DATA 0xFFD01410 0x04000000 # DDR Address Control
+DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
+DATA 0xFFD01418 0x00000000 # DDR Operation
+DATA 0xFFD0141C 0x00000672 # DDR Mode
+DATA 0xFFD01420 0x00000004 # DDR Extended Mode
+DATA 0xFFD01424 0x0000F14F # DDR Controller Control High
+DATA 0xFFD01428 0x000D6720 # DDR3 ODT Read Timing
+DATA 0xFFD0147C 0x0000B571 # DDR2 ODT Write Timing
+DATA 0xFFD01504 0x1FFFFFF1 # CS[0]n Size
+DATA 0xFFD01508 0x20000000 # CS[1]n Base address to 512Mb
+DATA 0xFFD0150C 0x1FFFFFF4 # CS[1]n Size 512Mb Window enabled for CS1
+DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
+DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
+DATA 0xFFD01494 0x00120000 # DDR ODT Control (Low)
+DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
+DATA 0xFFD0149C 0x0000E803 # CPU ODT Control
+
+DATA 0xFFD015D0 0x00000630
+DATA 0xFFD015D4 0x00000046
+DATA 0xFFD015D8 0x00000008
+DATA 0xFFD015DC 0x00000000
+DATA 0xFFD015E0 0x00000023
+DATA 0xFFD015E4 0x00203C18
+DATA 0xFFD01620 0x00384800
+DATA 0xFFD01480 0x00000001
+DATA 0xFFD20134 0x66666666
+DATA 0xFFD20138 0x00066666
+
+#Disable nsa325 hardware watchdog to allow successful kwbooting
+DATA 0xFFD10100 0x00004000 # set GPIO 14 to high to disable the watchdog
+DATA 0xFFD10104 0xFFFFBFFF # set GPIO 14 to output (to block any other input to it)
+
+# End of Header extension
+DATA 0x0 0x0
+
--- /dev/null
+++ b/board/zyxel/nsa325/nsa325.c
@@ -0,0 +1,265 @@
+/*
+ * Copyright (C) 2015 bodhi <mibodhi@gmail.com>
+ *
+ * Based on
+ * Copyright (C) 2014 Jason Plum <jplum@archlinuxarm.org>
+ *
+ * Based on nsa320.c originall written by
+ * Copyright (C) 2012 Peter Schildmann <linux@schildmann.info>
+ *
+ * Based on guruplug.c originally written by
+ * Siddarth Gore <gores@marvell.com>
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/arch/soc.h>
+#include <asm/arch/mpp.h>
+#include <asm/arch/cpu.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include "nsa325.h"
+#include <asm/arch/gpio.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+ /*
+ * default gpio configuration
+ * There are maximum 64 gpios controlled through 2 sets of registers
+ * the below configuration configures mainly initial LED status
+ */
+ mvebu_config_gpio(NSA325_VAL_LOW, NSA325_VAL_HIGH,
+ NSA325_OE_LOW, NSA325_OE_HIGH);
+
+ /* Multi-Purpose Pins Functionality configuration */
+ /* (all LEDs & power off active high) */
+ u32 kwmpp_config[] = {
+ MPP0_NF_IO2,
+ MPP1_NF_IO3,
+ MPP2_NF_IO4,
+ MPP3_NF_IO5,
+ MPP4_NF_IO6,
+ MPP5_NF_IO7,
+ MPP6_SYSRST_OUTn,
+ MPP7_GPO,
+ MPP8_TW_SDA, /* PCF8563 RTC chip */
+ MPP9_TW_SCK, /* connected to TWSI */
+ MPP10_UART0_TXD,
+ MPP11_UART0_RXD,
+ MPP12_GPO, /* HDD2 LED (green) */
+ MPP13_GPIO, /* HDD2 LED (red) */
+ MPP14_GPIO, /* MCU DATA pin (in) */
+ MPP15_GPIO, /* USB LED (green) */
+ MPP16_GPIO, /* MCU CLK pin (out) */
+ MPP17_GPIO, /* MCU ACT pin (out) */
+ MPP18_NF_IO0,
+ MPP19_NF_IO1,
+ MPP20_GPIO,
+ MPP21_GPIO, /* USB power */
+ MPP22_GPIO,
+ MPP23_GPIO,
+ MPP24_GPIO,
+ MPP25_GPIO,
+ MPP26_GPIO,
+ MPP27_GPIO,
+ MPP28_GPIO, /* SYS LED (green) */
+ MPP29_GPIO, /* SYS LED (orange) */
+ MPP30_GPIO,
+ MPP31_GPIO,
+ MPP32_GPIO,
+ MPP33_GPIO,
+ MPP34_GPIO,
+ MPP35_GPIO,
+ MPP36_GPIO, /* reset button */
+ MPP37_GPIO, /* copy button */
+ MPP38_GPIO, /* VID B0 */
+ MPP39_GPIO, /* COPY LED (green) */
+ MPP40_GPIO, /* COPY LED (red) */
+ MPP41_GPIO, /* HDD1 LED (green) */
+ MPP42_GPIO, /* HDD1 LED (red) */
+ MPP43_GPIO, /* HTP pin */
+ MPP44_GPIO, /* buzzer */
+ MPP45_GPIO, /* VID B1 */
+ MPP46_GPIO, /* power button */
+ MPP47_GPIO, /* HDD2 power */
+ MPP48_GPIO, /* power off */
+ 0
+ };
+ kirkwood_mpp_conf(kwmpp_config, NULL);
+ return 0;
+}
+
+int board_init(void)
+{
+
+ /* address of boot parameters */
+ gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
+
+ /* This disables the hardware watchdog in the mcu on this board. */
+ kw_gpio_set_valid(14, 1);
+ kw_gpio_direction_output(14, 0);
+ kw_gpio_set_value(14, 1);
+
+ return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+/* Configure and enable MV88E1318 PHY */
+void reset_phy(void)
+{
+ u16 reg;
+ u16 devadr;
+ char *name = "egiga0";
+
+ if (miiphy_set_current_dev(name))
+ return;
+
+ /* command to read PHY dev address */
+ if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
+ printf("Err..%s could not read PHY dev address\n",
+ __FUNCTION__);
+ return;
+ }
+
+ /* Set RGMII delay */
+ miiphy_write(name, devadr, MV88E1318_PGADR_REG, MV88E1318_MAC_CTRL_PG);
+ miiphy_read(name, devadr, MV88E1318_MAC_CTRL_REG, &reg);
+ reg |= (MV88E1318_RGMII_RXTM_CTRL | MV88E1318_RGMII_TXTM_CTRL);
+ miiphy_write(name, devadr, MV88E1318_MAC_CTRL_REG, reg);
+ miiphy_write(name, devadr, MV88E1318_PGADR_REG, 0);
+
+ /* reset the phy */
+ miiphy_reset(name, devadr);
+
+ /* The ZyXEL NSA325 uses the 88E1310S Alaska (interface identical to 88E1318) */
+ /* and has an MCU attached to the LED[2] via tristate interrupt */
+ reg = 0;
+
+ /* switch to LED register page */
+ miiphy_write(name, devadr, MV88E1318_PGADR_REG, MV88E1318_LED_PG);
+ /* read out LED polarity register */
+ miiphy_read(name, devadr, MV88E1318_LED_POL_REG, &reg);
+ /* clear 4, set 5 - LED2 low, tri-state */
+ reg &= ~(MV88E1318_LED2_4);
+ reg |= (MV88E1318_LED2_5);
+ /* write back LED polarity register */
+ miiphy_write(name, devadr, MV88E1318_LED_POL_REG, reg);
+ /* jump back to page 0, per the PHY chip documenation. */
+ miiphy_write(name, devadr, MV88E1318_PGADR_REG, 0);
+
+ /* Set the phy back to auto-negotiation mode. Onboard mcu sets it as 10Mbits/s on poweroff for WoL function */
+ miiphy_write(name, devadr, 0x4, 0x1e1);
+ miiphy_write(name, devadr, 0x9, 0x300);
+ /* Downshift */
+ miiphy_write(name, devadr, 0x10, 0x3860);
+ miiphy_write(name, devadr, 0x0, 0x9140);
+
+ printf("MV88E1318 PHY initialized on %s\n", name);
+
+}
+#endif /* CONFIG_RESET_PHY_R */
+
+#ifdef CONFIG_SHOW_BOOT_PROGRESS
+void show_boot_progress(int val)
+{
+ struct kwgpio_registers *gpio0 = (struct kwgpio_registers *)MVEBU_GPIO0_BASE;
+ u32 dout0 = readl(&gpio0->dout);
+ u32 blen0 = readl(&gpio0->blink_en);
+
+ struct kwgpio_registers *gpio1 = (struct kwgpio_registers *)MVEBU_GPIO1_BASE;
+ u32 dout1 = readl(&gpio1->dout);
+ u32 blen1 = readl(&gpio1->blink_en);
+
+ switch (val) {
+ case BOOTSTAGE_ID_DECOMP_IMAGE:
+ writel(blen0 & ~(SYS_GREEN_LED | SYS_ORANGE_LED), &gpio0->blink_en);
+ writel((dout0 & ~SYS_GREEN_LED) | SYS_ORANGE_LED, &gpio0->dout);
+ break;
+ case BOOTSTAGE_ID_RUN_OS:
+ writel(dout0 & ~SYS_ORANGE_LED, &gpio0->dout);
+ writel(blen0 | SYS_GREEN_LED, &gpio0->blink_en);
+ break;
+ case BOOTSTAGE_ID_NET_START:
+ writel(dout1 & ~COPY_RED_LED, &gpio1->dout);
+ writel((blen1 & ~COPY_RED_LED) | COPY_GREEN_LED, &gpio1->blink_en);
+ break;
+ case BOOTSTAGE_ID_NET_LOADED:
+ writel(blen1 & ~(COPY_RED_LED | COPY_GREEN_LED), &gpio1->blink_en);
+ writel((dout1 & ~COPY_RED_LED) | COPY_GREEN_LED, &gpio1->dout);
+ break;
+ case -BOOTSTAGE_ID_NET_NETLOOP_OK:
+ case -BOOTSTAGE_ID_NET_LOADED:
+ writel(dout1 & ~COPY_GREEN_LED, &gpio1->dout);
+ writel((blen1 & ~COPY_GREEN_LED) | COPY_RED_LED, &gpio1->blink_en);
+ break;
+ default:
+ if (val < 0) {
+ /* error */
+ printf("Error occured, error code = %d\n", -val);
+ writel(dout0 & ~SYS_GREEN_LED, &gpio0->dout);
+ writel(blen0 | SYS_ORANGE_LED, &gpio0->blink_en);
+ }
+ break;
+ }
+}
+#endif
+
+#if defined(CONFIG_KIRKWOOD_GPIO)
+/* Return GPIO button status */
+/*
+un-pressed:
+ gpio-36 (Reset Button ) in hi (act lo) - IRQ edge (clear )
+ gpio-37 (Copy Button ) in hi (act lo) - IRQ edge (clear )
+ gpio-46 (Power Button ) in lo (act hi) - IRQ edge (clear )
+pressed
+ gpio-36 (Reset Button ) in lo (act hi) - IRQ edge (clear )
+ gpio-37 (Copy Button ) in lo (act hi) - IRQ edge (clear )
+ gpio-46 (Power Button ) in hi (act lo) - IRQ edge (clear )
+*/
+
+static int
+do_read_button(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ if (strcmp(argv[1], "power") == 0) {
+ kw_gpio_set_valid(BTN_POWER, GPIO_INPUT_OK);
+ kw_gpio_direction_input(BTN_POWER);
+ return !kw_gpio_get_value(BTN_POWER);
+ }
+ else if (strcmp(argv[1], "reset") == 0)
+ return kw_gpio_get_value(BTN_RESET);
+ else if (strcmp(argv[1], "copy") == 0)
+ return kw_gpio_get_value(BTN_COPY);
+ else
+ return -1;
+}
+
+
+U_BOOT_CMD(button, 2, 0, do_read_button,
+ "Return GPIO button status 0=off 1=on",
+ "- button power|reset|copy: test buttons states\n"
+);
+
+#endif
+
--- /dev/null
+++ b/board/zyxel/nsa325/nsa325.h
@@ -0,0 +1,77 @@
+/*
+ * Copyright (C) 2014 Jason Plum <jplum@archlinuxarm.org>
+ *
+ * Based on nsa320.h originall written by
+ * Copyright (C) 2012 Peter Schildmann <linux@schildmann.info>
+ *
+ * Based on guruplug.h originally written by
+ * Siddarth Gore <gores@marvell.com>
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __NSA325_H
+#define __NSA325_H
+
+/* low GPIO's */
+#define HDD2_GREEN_LED (1 << 12)
+#define HDD2_RED_LED (1 << 13)
+#define USB_GREEN_LED (1 << 15)
+#define USB_POWER (1 << 21)
+#define SYS_GREEN_LED (1 << 28)
+#define SYS_ORANGE_LED (1 << 29)
+
+#define PIN_USB_GREEN_LED 15
+#define PIN_USB_POWER 21
+
+#define NSA325_OE_LOW (~(HDD2_GREEN_LED | HDD2_RED_LED | \
+ USB_GREEN_LED | USB_POWER | \
+ SYS_GREEN_LED | SYS_ORANGE_LED))
+#define NSA325_VAL_LOW (SYS_GREEN_LED | USB_POWER)
+
+/* high GPIO's */
+#define COPY_GREEN_LED (1 << 7)
+#define COPY_RED_LED (1 << 8)
+#define HDD1_GREEN_LED (1 << 9)
+#define HDD1_RED_LED (1 << 10)
+#define HDD2_POWER (1 << 15)
+#define WATCHDOG_SIGNAL (1 << 14)
+
+#define NSA325_OE_HIGH (~(COPY_GREEN_LED | COPY_RED_LED | \
+ HDD1_GREEN_LED | HDD1_RED_LED | HDD2_POWER | WATCHDOG_SIGNAL ))
+#define NSA325_VAL_HIGH (WATCHDOG_SIGNAL | HDD2_POWER)
+
+/* PHY related */
+#define MV88E1318_PGADR_REG 22
+#define MV88E1318_MAC_CTRL_PG 2
+#define MV88E1318_MAC_CTRL_REG 21
+#define MV88E1318_RGMII_TXTM_CTRL (1 << 4)
+#define MV88E1318_RGMII_RXTM_CTRL (1 << 5)
+#define MV88E1318_LED_PG 3
+#define MV88E1318_LED_POL_REG 17
+#define MV88E1318_LED2_4 (1 << 4)
+#define MV88E1318_LED2_5 (1 << 5)
+
+#define BTN_POWER 46
+#define BTN_RESET 36
+#define BTN_COPY 37
+
+#endif /* __NSA325_H */
--- /dev/null
+++ b/configs/nsa325_defconfig
@@ -0,0 +1,48 @@
+CONFIG_ARM=y
+CONFIG_SYS_DCACHE_OFF=y
+CONFIG_ARCH_CPU_INIT=y
+CONFIG_KIRKWOOD=y
+CONFIG_SYS_TEXT_BASE=0x600000
+CONFIG_TARGET_NSA325=y
+CONFIG_IDENT_STRING="\nZyXEL NSA325 2-Bay Power Media Server"
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_BOOTDELAY=3
+CONFIG_SYS_PROMPT="NSA325> "
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_MVGBE=y
+CONFIG_MII=y
+CONFIG_SYS_NS16550=y
+CONFIG_CMD_FDT=y
+CONFIG_OF_LIBFDT=y
+CONFIG_CMD_SETEXPR=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_DNS=y
+CONFIG_CMD_SNTP=y
+CONFIG_CMD_USB=y
+CONFIG_USB=y
+CONFIG_CMD_DATE=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_JFFS2=y
+CONFIG_MTD=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:0x0c0000(uboot),0x80000(uboot_env),0x7ec0000(ubi)"
+CONFIG_CMD_MTDPARTS=y
+CONFIG_CMD_ENV=y
+CONFIG_CMD_NAND=y
+CONFIG_EFI_PARTITION=y
+CONFIG_ENV_IS_IN_NAND=y
+CONFIG_ENV_SIZE=0x20000
+CONFIG_ENV_OFFSET=0xC0000
+CONFIG_ENV_SECT_SIZE=0x20000
+CONFIG_ENV_ADDR=0xC0000
+CONFIG_CMD_UBI=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_STORAGE=y
+CONFIG_LZMA=y
+CONFIG_LZO=y
+CONFIG_SYS_LONGHELP=y
--- /dev/null
+++ b/include/configs/nsa325.h
@@ -0,0 +1,106 @@
+/*
+ * (C) Copyright 2016 bodhi <mibodhi@gmail.com>
+ *
+ * Based on
+ * Copyright (C) 2014 Jason Plum <jplum@archlinuxarm.org>
+ * Based on
+ * Copyright (C) 2012 Peter Schildmann <linux@schildmann.info>
+ *
+ * Based on guruplug.h originally written by
+ * Siddarth Gore <gores@marvell.com>
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_NSA325_H
+#define _CONFIG_NSA325_H
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
+#define CONFIG_KW88F6281 1 /* SOC Name */
+
+#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
+
+/*
+ * Misc Configuration Options
+ */
+#define CONFIG_SHOW_BOOT_PROGRESS 1 /* boot progess display (LED's) */
+
+/*
+ * Commands configuration
+ */
+#define CONFIG_PREBOOT
+
+/*
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
+ */
+#include "mv-common.h"
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_BOOTCOMMAND \
+ "ubi part ubi; " \
+ "ubi read 0x800000 kernel; " \
+ "bootm 0x800000"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "console=console=ttyS0,115200\0" \
+ "mtdids=nand0=orion_nand\0" \
+ "mtdparts="CONFIG_MTDPARTS_DEFAULT "\0" \
+ "bootargs_root=\0"
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
+#define CONFIG_PHY_BASE_ADR 0x1
+#define CONFIG_NETCONSOLE
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * SATA Driver configuration
+ */
+#ifdef CONFIG_MVSATA_IDE
+#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
+#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET
+#endif /* CONFIG_MVSATA_IDE */
+
+/*
+ * File system
+ */
+#define CONFIG_JFFS2_NAND
+#define CONFIG_JFFS2_LZO
+
+/*
+ * Date Time
+ */
+#ifdef CONFIG_CMD_DATE
+#define CONFIG_RTC_MV
+#endif /* CONFIG_CMD_DATE */
+
+#define CONFIG_KIRKWOOD_GPIO /* Enable GPIO Support */
+
+#endif /* _CONFIG_NSA325_H */
Reference in New Issue View Git Blame Copy Permalink