Openwrt/msm8916-openwrt
1
0
Fork 0
forked from Openwrt/openwrt
Code Issues 1 Pull Requests Actions Activity
msm8916
msm8916-openwrt/package/boot/uboot-kirkwood/patches/007-nsa310-uboot-generic.patch
Adrian Schmutzler 482e65a16d uboot-kirkwood: refresh patches 
This is only cosmetic, but the next one adding a patch here would
have to do it anyway, and thus will get a smaller diff for review
now.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-06 19:06:29 +02:00

663 lines
19 KiB
Diff
Raw Permalink Blame History

arm: kirkwood: add ZyXEL NSA310 device
This patch add ZyXEL NSA310 1-Bay Media Server
The ZyXEL NSA310 device is a Kirkwood based NAS:
- SoC: Marvell 88F6702 1200Mhz
- SDRAM memory: 256MB DDR2 400Mhz
- Gigabit ethernet: PHY Realtek
- Flash memory: 128MB
- 1 Power button
- 1 Power LED (blue)
- 5 Status LED (green/red)
- 1 Copy/Sync button
- 1 Reset button
- 2 SATA II port (1 internal and 1 external eSata)
- 2 USB 2.0 ports (1 front and 1 back)
- Smart fan
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
NOTE: this patch is ready for upstream, LEDE-specific parts are in
another patch
--- a/arch/arm/mach-kirkwood/Kconfig
+++ b/arch/arm/mach-kirkwood/Kconfig
@@ -53,6 +53,9 @@ config TARGET_GOFLEXHOME
config TARGET_NAS220
bool "BlackArmor NAS220"
+config TARGET_NSA310
+ bool "Zyxel NSA310 Board"
+
config TARGET_NSA310S
bool "Zyxel NSA310S"
@@ -86,6 +89,7 @@ source "board/raidsonic/ib62x0/Kconfig"
source "board/Seagate/dockstar/Kconfig"
source "board/Seagate/goflexhome/Kconfig"
source "board/Seagate/nas220/Kconfig"
+source "board/zyxel/nsa310/Kconfig"
source "board/zyxel/nsa310s/Kconfig"
source "board/alliedtelesis/SBx81LIFKW/Kconfig"
source "board/alliedtelesis/SBx81LIFXCAT/Kconfig"
--- /dev/null
+++ b/board/zyxel/nsa310/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_NSA310
+
+config SYS_BOARD
+ default "nsa310"
+
+config SYS_VENDOR
+ default "zyxel"
+
+config SYS_CONFIG_NAME
+ default "nsa310"
+
+endif
--- /dev/null
+++ b/board/zyxel/nsa310/MAINTAINERS
@@ -0,0 +1,6 @@
+NSA310 BOARD
+M: Alberto Bursi <alberto.bursi@outlook.it>
+S: Maintained
+F: board/zyxel/nsa310/
+F: include/configs/nsa310.h
+F: configs/nsa310_defconfig
--- /dev/null
+++ b/board/zyxel/nsa310/Makefile
@@ -0,0 +1,12 @@
+#
+# (C) Copyright 2015 bodhi <mibodhi@gmail.com>
+#
+# Based on
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := nsa310.o
--- /dev/null
+++ b/board/zyxel/nsa310/kwbimage.cfg
@@ -0,0 +1,166 @@
+#
+# Copyright (C) 2013 Rafal Kazmierowski
+#
+# Based on guruplug.c originally written by
+# Siddarth Gore <gores@marvell.com>
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM nand
+#BOOT_FROM uart
+NAND_ECC_MODE default
+NAND_PAGE_SIZE 0x0800
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+
+# Configure RGMII-0 interface pad voltage to 1.8V
+DATA 0xFFD100e0 0x1b1b1b9b
+
+#Dram initalization for SINGLE x16 CL=5 @ 400MHz
+DATA 0xFFD01400 0x43010c30 # DDR Configuration register
+# bit13-0: 0xc30 (3120 DDR2 clks refresh rate)
+# bit23-14: zero
+# bit24: 1= enable exit self refresh mode on DDR access
+# bit25: 1 required
+# bit29-26: zero
+# bit31-30: 01
+
+DATA 0xFFD01404 0x37543000 # DDR Controller Control Low
+# bit 4: 0=addr/cmd in smame cycle
+# bit 5: 0=clk is driven during self refresh, we don't care for APX
+# bit 6: 0=use recommended falling edge of clk for addr/cmd
+# bit14: 0=input buffer always powered up
+# bit18: 1=cpu lock transaction enabled
+# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
+# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
+# bit30-28: 3 required
+# bit31: 0=no additional STARTBURST delay
+
+DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
+# bit3-0: TRAS lsbs
+# bit7-4: TRCD
+# bit11- 8: TRP
+# bit15-12: TWR
+# bit19-16: TWTR
+# bit20: TRAS msb
+# bit23-21: 0x0
+# bit27-24: TRRD
+# bit31-28: TRTP
+
+DATA 0xFFD0140C 0x00000a33 # DDR Timing (High)
+# bit6-0: TRFC
+# bit8-7: TR2R
+# bit10-9: TR2W
+# bit12-11: TW2W
+# bit31-13: zero required
+
+DATA 0xFFD01410 0x0000000c # DDR Address Control
+# bit1-0: 01, Cs0width=x8
+# bit3-2: 10, Cs0size=1Gb
+# bit5-4: 01, Cs1width=x8
+# bit7-6: 10, Cs1size=1Gb
+# bit9-8: 00, Cs2width=nonexistent
+# bit11-10: 00, Cs2size =nonexistent
+# bit13-12: 00, Cs3width=nonexistent
+# bit15-14: 00, Cs3size =nonexistent
+# bit16: 0, Cs0AddrSel
+# bit17: 0, Cs1AddrSel
+# bit18: 0, Cs2AddrSel
+# bit19: 0, Cs3AddrSel
+# bit31-20: 0 required
+
+DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
+# bit0: 0, OpenPage enabled
+# bit31-1: 0 required
+
+DATA 0xFFD01418 0x00000000 # DDR Operation
+# bit3-0: 0x0, DDR cmd
+# bit31-4: 0 required
+
+DATA 0xFFD0141C 0x00000652 # DDR Mode
+# bit2-0: 2, BurstLen=2 required
+# bit3: 0, BurstType=0 required
+# bit6-4: 4, CL=5
+# bit7: 0, TestMode=0 normal
+# bit8: 0, DLL reset=0 normal
+# bit11-9: 6, auto-precharge write recovery ????????????
+# bit12: 0, PD must be zero
+# bit31-13: 0 required
+
+DATA 0xFFD01420 0x00000004 # DDR Extended Mode
+# bit0: 0, DDR DLL enabled
+# bit1: 0, DDR drive strenght normal
+# bit2: 0, DDR ODT control lsd (disabled)
+# bit5-3: 000, required
+# bit6: 1, DDR ODT control msb, (disabled)
+# bit9-7: 000, required
+# bit10: 0, differential DQS enabled
+# bit11: 0, required
+# bit12: 0, DDR output buffer enabled
+# bit31-13: 0 required
+
+DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
+# bit2-0: 111, required
+# bit3 : 1 , MBUS Burst Chop disabled
+# bit6-4: 111, required
+# bit7 : 0
+# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
+# bit9 : 0 , no half clock cycle addition to dataout
+# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
+# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
+# bit15-12: 1111 required
+# bit31-16: 0 required
+
+DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
+DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
+
+
+DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
+#DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
+# bit0: 1, Window enabled
+# bit1: 0, Write Protect disabled
+# bit3-2: 00, CS0 hit selected
+# bit23-4: ones, required
+# bit31-24: 0x0F, Size (i.e. 256MB)
+
+DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb
+DATA 0xFFD0150C 0x00000000 # CS[2]n Size, window disabled KAZ z 400db
+DATA 0xFFD01514 0x00000000 # CS[3]n Size, window disabled
+
+DATA 0xFFD0151C 0x00000000 # DDR ODT Control (Low)
+DATA 0xFFD01494 0x00120012 # DDR ODT Control (High) KAZ z nowy STATIC_SDRAM_ODT_CTRL_LOW
+# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
+# bit3-2: 01, ODT1 active NEVER!
+# bit31-4: zero, required
+
+DATA 0xFFD01498 0x00000000 # CPU ODT Control KAZ STATIC_SDRAM_ODT_CTRL_HI
+DATA 0xFFD0149C 0x0000E403 # DDR Initialization Control KAZ STATIC_SDRAM_DUNIT_ODT_CTRL
+DATA 0xFFD01480 0x00000001 # DDR Initialization Control
+#bit0=1, enable DDR init upon this register write
+
+# End of Header extension
+DATA 0x0 0x0
--- /dev/null
+++ b/board/zyxel/nsa310/nsa310.c
@@ -0,0 +1,190 @@
+/*
+ * Copyright (C) 2013 Rafal Kazmierowski
+ *
+ * Based on NSA320.c Peter Schildmann <linux@schildmann.info>
+ * originally written by
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/soc.h>
+#include <asm/arch/mpp.h>
+#include <asm/io.h>
+#include "nsa310.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+ /*
+ * default gpio configuration
+ * There are maximum 64 gpios controlled through 2 sets of registers
+ * the below configuration configures mainly initial LED status
+ */
+ mvebu_config_gpio(NSA310_VAL_LOW, NSA310_VAL_HIGH,
+ NSA310_OE_LOW, NSA310_OE_HIGH);
+
+ /* Multi-Purpose Pins Functionality configuration */
+ /* (all LEDs & power off active high) */
+ static const u32 kwmpp_config[] = {
+ MPP0_NF_IO2,
+ MPP1_NF_IO3,
+ MPP2_NF_IO4,
+ MPP3_NF_IO5,
+ MPP4_NF_IO6,
+ MPP5_NF_IO7,
+ MPP6_SYSRST_OUTn,
+ MPP7_GPO,
+ MPP8_TW_SDA, /* PCF8563 RTC chip */
+ MPP9_TW_SCK, /* connected to TWSI */
+ MPP10_UART0_TXD,
+ MPP11_UART0_RXD,
+ MPP12_GPO, /* SATA2 LED (green) */
+ MPP13_GPIO, /* SATA2 LED (red) */
+ MPP14_GPIO, /* MCU DATA pin (in) */
+ MPP15_GPIO, /* USB LED (green) */
+ MPP16_GPIO, /* MCU CLK pin (out) */
+ MPP17_GPIO, /* MCU ACT pin (out) */
+ MPP18_NF_IO0,
+ MPP19_NF_IO1,
+ MPP20_GPIO,
+ MPP21_GPIO, /* USB LED (red)-Power*/
+ MPP22_GPIO,
+ MPP23_GPIO,
+ MPP24_GPIO,
+ MPP25_GPIO,
+ MPP26_GPIO,
+ MPP27_GPIO,
+ MPP28_GPIO, /* SYS LED (green) */
+ MPP29_GPIO, /* SYS LED (red) */
+ MPP30_GPIO,
+ MPP31_GPIO,
+ MPP32_GPIO,
+ MPP33_GPIO,
+ MPP34_GPIO,
+ MPP35_GPIO,
+ MPP36_GPIO, /* Reset button */
+ MPP37_GPIO, /* Copy button */
+ MPP38_GPIO, /* VID B0 */
+ MPP39_GPIO, /* COPY LED (green) */
+ MPP40_GPIO, /* COPY LED (red) */
+ MPP41_GPIO, /* SATA1 LED (green) */
+ MPP42_GPIO, /* SATA1 LED (red) */
+ MPP43_GPIO, /* HTP pin */
+ MPP44_GPIO, /* Buzzer */
+ MPP45_GPIO, /* VID B1 */
+ MPP46_GPIO, /* Power button */
+ MPP47_GPIO, /* Power resume data */
+ MPP48_GPIO, /* Power off */
+ MPP49_GPIO, /* Power resume clock */
+ 0
+ };
+ kirkwood_mpp_conf(kwmpp_config,NULL);
+ return 0;
+}
+
+int board_init(void)
+{
+ /* address of boot parameters */
+ gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
+
+ return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+/* Configure and enable MV88E1318 PHY */
+void reset_phy(void)
+{
+ u16 reg;
+ u16 devadr;
+ char *name = "egiga0";
+
+ if (miiphy_set_current_dev(name))
+ return;
+
+ /* command to read PHY dev address */
+ if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
+ printf("Err..%s could not read PHY dev address\n",
+ __FUNCTION__);
+ return;
+ }
+
+ /* Set RGMII delay */
+ miiphy_write(name, devadr, MV88E1318_PGADR_REG, 2);
+ miiphy_read(name, devadr, MV88E1318_MAC_CTRL_REG, &reg);
+ reg |= (MV88E1318_RGMII_RXTM_CTRL | MV88E1318_RGMII_TXTM_CTRL);
+ miiphy_write(name, devadr, MV88E1318_MAC_CTRL_REG, reg);
+ miiphy_write(name, devadr, MV88E1318_PGADR_REG, 0);
+
+ /* reset the phy */
+ miiphy_reset(name, devadr);
+
+ printf("MV88E1318 PHY initialized on %s\n", name);
+}
+#endif /* CONFIG_RESET_PHY_R */
+
+#ifdef CONFIG_SHOW_BOOT_PROGRESS
+void show_boot_progress(int val)
+{
+ struct kwgpio_registers *gpio0 = (struct kwgpio_registers *)MVEBU_GPIO0_BASE;
+ u32 dout0 = readl(&gpio0->dout);
+ u32 blen0 = readl(&gpio0->blink_en);
+
+ struct kwgpio_registers *gpio1 = (struct kwgpio_registers *)MVEBU_GPIO1_BASE;
+ u32 dout1 = readl(&gpio1->dout);
+ u32 blen1 = readl(&gpio1->blink_en);
+
+ switch (val) {
+ case BOOTSTAGE_ID_DECOMP_IMAGE:
+ writel(blen0 & ~(SYS_GREEN_LED | SYS_RED_LED), &gpio0->blink_en);
+ writel((dout0 & ~SYS_GREEN_LED) | SYS_RED_LED, &gpio0->dout);
+ break;
+ case BOOTSTAGE_ID_RUN_OS:
+ writel(dout0 & ~SYS_RED_LED, &gpio0->dout);
+ writel(blen0 | SYS_GREEN_LED, &gpio0->blink_en);
+ break;
+ case BOOTSTAGE_ID_NET_START:
+ writel(dout1 & ~COPY_RED_LED, &gpio1->dout);
+ writel((blen1 & ~COPY_RED_LED) | COPY_GREEN_LED, &gpio1->blink_en);
+ break;
+ case BOOTSTAGE_ID_NET_LOADED:
+ writel(blen1 & ~(COPY_RED_LED | COPY_GREEN_LED), &gpio1->blink_en);
+ writel((dout1 & ~COPY_RED_LED) | COPY_GREEN_LED, &gpio1->dout);
+ break;
+ case -BOOTSTAGE_ID_NET_NETLOOP_OK:
+ case -BOOTSTAGE_ID_NET_LOADED:
+ writel(dout1 & ~COPY_GREEN_LED, &gpio1->dout);
+ writel((blen1 & ~COPY_GREEN_LED) | COPY_RED_LED, &gpio1->blink_en);
+ break;
+ default:
+ if (val < 0) {
+ /* error */
+ printf("Error occured, error code = %d\n", -val);
+ writel(dout0 & ~SYS_GREEN_LED, &gpio0->dout);
+ writel(blen0 | SYS_RED_LED, &gpio0->blink_en);
+ }
+ break;
+ }
+}
+#endif
--- /dev/null
+++ b/board/zyxel/nsa310/nsa310.h
@@ -0,0 +1,56 @@
+/*
+ * Copyright (C) 2013 Rafal Kazmierowski
+ *
+ * Based on Peter Schildmann <linux@schildmann.info>
+ * and guruplug.h originally written by
+ * Siddarth Gore <gores@marvell.com>
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __NSA310_H
+#define __NSA310_H
+
+/* GPIO's */
+#define SYS_GREEN_LED (1 << 28)
+#define SYS_RED_LED (1 << 29)
+#define SATA1_GREEN_LED (1ULL << 41)
+#define SATA1_RED_LED (1ULL << 42)
+#define SATA2_GREEN_LED (1 << 12)
+#define SATA2_RED_LED (1 << 13)
+#define USB_GREEN_LED (1 << 15)
+#define USB_RED_LED (1 << 21)
+#define COPY_GREEN_LED (1ULL << 39)
+#define COPY_RED_LED (1ULL << 40)
+
+#define NSA310_OE_LOW (0)
+#define NSA310_VAL_LOW (SYS_GREEN_LED)
+#define NSA310_OE_HIGH (((COPY_GREEN_LED | COPY_RED_LED | \
+ SATA1_GREEN_LED | SATA1_RED_LED)) >> 32UL)
+#define NSA310_VAL_HIGH (0)
+
+/* PHY related */
+#define MV88E1318_MAC_CTRL_REG 21
+#define MV88E1318_PGADR_REG 22
+#define MV88E1318_RGMII_TXTM_CTRL (1 << 4)
+#define MV88E1318_RGMII_RXTM_CTRL (1 << 5)
+
+#endif /* __NSA310_H */
--- /dev/null
+++ b/configs/nsa310_defconfig
@@ -0,0 +1,48 @@
+CONFIG_ARM=y
+CONFIG_SYS_DCACHE_OFF=y
+CONFIG_ARCH_CPU_INIT=y
+CONFIG_KIRKWOOD=y
+CONFIG_SYS_TEXT_BASE=0x600000
+CONFIG_TARGET_NSA310=y
+CONFIG_IDENT_STRING="\nZyXEL NSA310 1-Bay Power Media Server"
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_BOOTDELAY=3
+CONFIG_SYS_PROMPT="NSA310> "
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_MVGBE=y
+CONFIG_MII=y
+CONFIG_SYS_NS16550=y
+CONFIG_CMD_FDT=y
+CONFIG_OF_LIBFDT=y
+CONFIG_CMD_SETEXPR=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_DNS=y
+CONFIG_CMD_SNTP=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_DATE=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_JFFS2=y
+CONFIG_MTD=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:0x0c0000(uboot),0x80000(uboot_env),0x7ec0000(ubi)"
+CONFIG_CMD_MTDPARTS=y
+CONFIG_CMD_ENV=y
+CONFIG_CMD_NAND=y
+CONFIG_EFI_PARTITION=y
+CONFIG_ENV_IS_IN_NAND=y
+CONFIG_ENV_SIZE=0x20000
+CONFIG_ENV_OFFSET=0xC0000
+CONFIG_ENV_SECT_SIZE=0x20000
+CONFIG_ENV_ADDR=0xC0000
+CONFIG_CMD_UBI=y
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_STORAGE=y
+CONFIG_LZMA=y
+CONFIG_LZO=y
+CONFIG_SYS_LONGHELP=y
--- /dev/null
+++ b/include/configs/nsa310.h
@@ -0,0 +1,103 @@
+/* Copyright (C) 2015-2016 bodhi <mibodhi@gmail.com>
+ *
+ * Based on
+ * Copyright (C) 2012 Peter Schildmann <linux@schildmann.info>
+ *
+ * Based on guruplug.h originally written by
+ * Siddarth Gore <gores@marvell.com>
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_NSA310_H
+#define _CONFIG_NSA310_H
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_FEROCEON_88FR131 /* CPU Core subversion */
+#define CONFIG_KW88F6281 /* SOC Name */
+
+#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
+
+/*
+ * Misc Configuration Options
+ */
+#define CONFIG_SHOW_BOOT_PROGRESS 1 /* boot progess display (LED's) */
+
+/*
+ * Commands configuration
+ */
+#define CONFIG_PREBOOT
+
+/*
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
+ */
+#include "mv-common.h"
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_BOOTCOMMAND \
+ "ubi part ubi; " \
+ "ubi read 0x800000 kernel; " \
+ "bootm 0x800000"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "console=console=ttyS0,115200\0" \
+ "mtdids=nand0=orion_nand\0" \
+ "mtdparts="CONFIG_MTDPARTS_DEFAULT "\0" \
+ "bootargs_root=\0"
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_NETCONSOLE
+#define CONFIG_NET_MULTI
+#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
+#define CONFIG_PHY_BASE_ADR 0x1
+#define CONFIG_RESET_PHY_R
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * SATA Driver configuration
+ */
+#ifdef CONFIG_MVSATA_IDE
+#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
+#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET
+#endif /* CONFIG_MVSATA_IDE */
+
+/*
+ * File system
+ */
+#define CONFIG_JFFS2_NAND
+#define CONFIG_JFFS2_LZO
+
+/*
+ * Date Time
+ */
+#ifdef CONFIG_CMD_DATE
+#define CONFIG_RTC_MV
+#endif /* CONFIG_CMD_DATE */
+
+#endif /* _CONFIG_NSA310_H */
Reference in New Issue View Git Blame Copy Permalink