a5d6a60fd0
This is an automatically generated commit. When doing `git bisect`, consider `git bisect --skip`. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
60 lines
2.4 KiB
Diff
60 lines
2.4 KiB
Diff
From 56466f505f58f44b69feb7eaed3b506842800456 Mon Sep 17 00:00:00 2001
|
|
From: Ionela Voinescu <ionela.voinescu@imgtec.com>
|
|
Date: Tue, 1 Mar 2016 17:49:45 +0000
|
|
Subject: spi: img-spfi: RX maximum burst size for DMA is 8
|
|
|
|
The depth of the FIFOs is 16 bytes. The DMA request line is tied
|
|
to the half full/empty (depending on the use of the TX or RX FIFO)
|
|
threshold. For the TX FIFO, if you set a burst size of 8 (equal to
|
|
half the depth) the first burst goes into FIFO without any issues,
|
|
but due the latency involved (the time the data leaves the DMA
|
|
engine to the time it arrives at the FIFO), the DMA might trigger
|
|
another burst of 8. But given that there is no space for 2 additonal
|
|
bursts of 8, this would result in a failure. Therefore, we have to
|
|
keep the burst size for TX to 4 to accomodate for an extra burst.
|
|
|
|
For the read (RX) scenario, the DMA request line goes high when
|
|
there is at least 8 entries in the FIFO (half full), and we can
|
|
program the burst size to be 8 because the risk of accidental burst
|
|
does not exist. The DMA engine will not trigger another read until
|
|
the read data for all the burst it has sent out has been received.
|
|
|
|
While here, move the burst size setting outside of the if/else branches
|
|
as they have the same value for both 8 and 32 bit data widths.
|
|
|
|
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
|
|
---
|
|
drivers/spi/spi-img-spfi.c | 6 ++----
|
|
1 file changed, 2 insertions(+), 4 deletions(-)
|
|
|
|
--- a/drivers/spi/spi-img-spfi.c
|
|
+++ b/drivers/spi/spi-img-spfi.c
|
|
@@ -338,12 +338,11 @@ static int img_spfi_start_dma(struct spi
|
|
if (xfer->len % 4 == 0) {
|
|
rxconf.src_addr = spfi->phys + SPFI_RX_32BIT_VALID_DATA;
|
|
rxconf.src_addr_width = 4;
|
|
- rxconf.src_maxburst = 4;
|
|
} else {
|
|
rxconf.src_addr = spfi->phys + SPFI_RX_8BIT_VALID_DATA;
|
|
rxconf.src_addr_width = 1;
|
|
- rxconf.src_maxburst = 4;
|
|
}
|
|
+ rxconf.src_maxburst = 8;
|
|
dmaengine_slave_config(spfi->rx_ch, &rxconf);
|
|
|
|
rxdesc = dmaengine_prep_slave_sg(spfi->rx_ch, xfer->rx_sg.sgl,
|
|
@@ -362,12 +361,11 @@ static int img_spfi_start_dma(struct spi
|
|
if (xfer->len % 4 == 0) {
|
|
txconf.dst_addr = spfi->phys + SPFI_TX_32BIT_VALID_DATA;
|
|
txconf.dst_addr_width = 4;
|
|
- txconf.dst_maxburst = 4;
|
|
} else {
|
|
txconf.dst_addr = spfi->phys + SPFI_TX_8BIT_VALID_DATA;
|
|
txconf.dst_addr_width = 1;
|
|
- txconf.dst_maxburst = 4;
|
|
}
|
|
+ txconf.dst_maxburst = 4;
|
|
dmaengine_slave_config(spfi->tx_ch, &txconf);
|
|
|
|
txdesc = dmaengine_prep_slave_sg(spfi->tx_ch, xfer->tx_sg.sgl,
|