Openwrt-EcoNet/openwrt
1
0
Fork 0
Code Issues Pull Requests Actions Activity
main
openwrt/package/boot/uboot-d1/patches/0071-sunxi-Move-most-board-options-to-the-board-Kconfig.patch
Zoltan HERPAI d41d9befb9 uboot-d1: add bootloader for upcoming d1 target 
Add u-boot bootloader based on 2023.01 to support D1-based boards, currently:

 - Dongshan Nezha STU
 - LicheePi RV Dock
 - MangoPi MQ-Pro
 - Nezha D1

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2024-02-29 16:50:20 +01:00

198 lines
7.0 KiB
Diff
Raw Permalink Blame History

From 6a1b660a83b262237b6bebed26e44db923a86a6b Mon Sep 17 00:00:00 2001
From: Zoltan HERPAI <wigyori@uid0.hu>
Date: Tue, 6 Jun 2023 18:09:19 +0000
Subject: [PATCH 71/90] sunxi: Move most board options to the board Kconfig
This excludes options that are inherently ARM-specific or are specific
to legacy non-DM drivers.
Some help text is cleaned up along the way.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
---
arch/arm/mach-sunxi/Kconfig | 71 ------------------------------------
board/sunxi/Kconfig | 72 +++++++++++++++++++++++++++++++++++++
2 files changed, 72 insertions(+), 71 deletions(-)
--- a/arch/arm/mach-sunxi/Kconfig
+++ b/arch/arm/mach-sunxi/Kconfig
@@ -548,16 +548,6 @@ config DRAM_ODT_CORRECTION
then the correction is negative. Usually the value for this is 0.
endif
-config UART0_PORT_F
- bool "UART0 on MicroSD breakout board"
- ---help---
- Repurpose the SD card slot for getting access to the UART0 serial
- console. Primarily useful only for low level u-boot debugging on
- tablets, where normal UART0 is difficult to access and requires
- device disassembly and/or soldering. As the SD card can't be used
- at the same time, the system can be only booted in the FEL mode.
- Only enable this if you really know what you are doing.
-
config OLD_SUNXI_KERNEL_COMPAT
bool "Enable workarounds for booting old kernels"
---help---
@@ -571,20 +561,6 @@ config MACPWR
Set the pin used to power the MAC. This takes a string in the format
understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
-config MMC1_PINS_PH
- bool "Pins for mmc1 are on Port H"
- depends on MACH_SUN4I || MACH_SUN7I || MACH_SUN8I_R40
- ---help---
- Select this option for boards where mmc1 uses the Port H pinmux.
-
-config MMC_SUNXI_SLOT_EXTRA
- int "mmc extra slot number"
- default -1
- ---help---
- sunxi builds always enable mmc0, some boards also have a second sdcard
- slot or emmc on mmc1 - mmc3. Setting this to 1, 2 or 3 will enable
- support for this.
-
config I2C0_ENABLE
bool "Enable I2C/TWI controller 0"
default y if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUN8I_R40
@@ -612,16 +588,6 @@ config R_I2C_ENABLE
Set this to y to enable the I2C controller which is part of the PRCM.
endif
-config AXP_DISABLE_BOOT_ON_POWERON
- bool "Disable device boot on power plug-in"
- depends on AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
- default n
- ---help---
- Say Y here to prevent the device from booting up because of a plug-in
- event. When set, the device will boot into the SPL briefly to
- determine why it was powered on, and if it was determined because of
- a plug-in event instead of a button press event it will shut back off.
-
config VIDEO_SUNXI
bool "Enable graphical uboot console on HDMI, LCD or VGA"
depends on !MACH_SUN8I_A83T
@@ -850,41 +816,4 @@ config SPL_SPI_SUNXI
sunxi SPI Flash. It uses the same method as the boot ROM, so does
not need any extra configuration.
-config PINE64_DT_SELECTION
- bool "Enable Pine64 device tree selection code"
- depends on MACH_SUN50I
- help
- The original Pine A64 and Pine A64+ are similar but different
- boards and can be differed by the DRAM size. Pine A64 has
- 512MiB DRAM, and Pine A64+ has 1GiB or 2GiB. By selecting this
- option, the device tree selection code specific to Pine64 which
- utilizes the DRAM size will be enabled.
-
-config PINEPHONE_DT_SELECTION
- bool "Enable PinePhone device tree selection code"
- depends on MACH_SUN50I
- help
- Enable this option to automatically select the device tree for the
- correct PinePhone hardware revision during boot.
-
-config BLUETOOTH_DT_DEVICE_FIXUP
- string "Fixup the Bluetooth controller address"
- default ""
- help
- This option specifies the DT compatible name of the Bluetooth
- controller for which to set the "local-bd-address" property.
- Set this option if your device ships with the Bluetooth controller
- default address.
- The used address is "bdaddr" if set, and "ethaddr" with the LSB
- flipped elsewise.
-
endif
-
-config CHIP_DIP_SCAN
- bool "Enable DIPs detection for CHIP board"
- select SUPPORT_EXTENSION_SCAN
- select W1
- select W1_GPIO
- select W1_EEPROM
- select W1_EEPROM_DS24XXX
- select CMD_EXTENSION
--- a/board/sunxi/Kconfig
+++ b/board/sunxi/Kconfig
@@ -171,6 +171,78 @@ config SPL_IMAGE_TYPE
default "sunxi_egon" if SPL_IMAGE_TYPE_SUNXI_EGON
default "sunxi_toc0" if SPL_IMAGE_TYPE_SUNXI_TOC0
+config MMC_SUNXI_SLOT_EXTRA
+ int "MMC extra slot number"
+ default -1
+ help
+ sunxi builds always enable mmc0. Some boards also have a
+ second SD card slot or eMMC on mmc1 - mmc3. Setting this to 1,
+ 2 or 3 will enable support for this.
+
+config MMC1_PINS_PH
+ bool "MMC1 pins are on Port H"
+ depends on MACH_SUN4I || MACH_SUN7I || MACH_SUN8I_R40
+ help
+ Select this option on boards where mmc1 uses the Port H pinmux.
+
+config UART0_PORT_F
+ bool "UART0 pins are on Port F (MicroSD breakout board)"
+ help
+ Repurpose the SD card slot for getting access to the UART0
+ serial console. Primarily useful only for low level u-boot
+ debugging on tablets, where normal UART0 is difficult to
+ access and requires device disassembly and/or soldering. As
+ the SD card can't be used at the same time, the system can be
+ only booted in FEL mode. Only enable this if you really know
+ what you are doing.
+
+config AXP_DISABLE_BOOT_ON_POWERON
+ bool "Disable device boot on power plug-in"
+ depends on AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
+ help
+ Say Y here to prevent the device from booting up because of a
+ plug-in event. When set, the device will boot into the SPL
+ briefly to determine why it was powered on, and if the board
+ was powered on because of a plug-in event instead of a button
+ press event, it will shut back off.
+
+config CHIP_DIP_SCAN
+ bool "Enable DIPs detection for CHIP board"
+ select SUPPORT_EXTENSION_SCAN
+ select W1
+ select W1_GPIO
+ select W1_EEPROM
+ select W1_EEPROM_DS24XXX
+ select CMD_EXTENSION
+
+config PINE64_DT_SELECTION
+ bool "Enable Pine64 device tree selection code"
+ depends on MACH_SUN50I
+ help
+ The original Pine A64 and Pine A64+ are similar but different
+ boards and can be differed by the DRAM size. Pine A64 has
+ 512MiB DRAM, and Pine A64+ has 1GiB or 2GiB. By selecting this
+ option, the device tree selection code specific to Pine64 which
+ utilizes the DRAM size will be enabled.
+
+config PINEPHONE_DT_SELECTION
+ bool "Enable PinePhone device tree selection code"
+ depends on MACH_SUN50I
+ help
+ Enable this option to automatically select the device tree for the
+ correct PinePhone hardware revision during boot.
+
+config BLUETOOTH_DT_DEVICE_FIXUP
+ string "Fixup the Bluetooth controller address"
+ default ""
+ help
+ This option specifies the DT compatible name of the Bluetooth
+ controller for which to set the "local-bd-address" property.
+ Set this option if your device ships with the Bluetooth controller
+ default address.
+ The used address is "bdaddr" if set, and "ethaddr" with the LSB
+ flipped elsewise.
+
endmenu
endif
Reference in New Issue View Git Blame Copy Permalink