Android/edk2-msm
0
0
Fork 1
mirror of https://github.com/edk2-porting/edk2-msm synced 2025-06-23 12:52:49 +00:00
Code Activity
Files
v0.2.1
edk2-msm/sdm845Pkg/FdtBlob/sdm845-oneplus-enchilada.dtsi
Not extraordinary 99a1cf935d Update device tree
2020-08-10 12:56:41 +08:00

877 lines
18 KiB
Plaintext
Raw Permalink Blame History

// SPDX-License-Identifier: GPL-2.0
/*
* SDM845 OnePlus 6(T) (enchilada / fajita) common device tree source
*
* Copyright (c) 2020, The Linux Foundation. All rights reserved.
*/
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
#include <dt-bindings/input/linux-event-codes.h>
#include "sdm845.dtsi"
// Needed for some GPIO (like the volume buttons)
#include "pm8998.dtsi"
// For LEDs
#include "pmi8998.dtsi"
/ {
aliases {
hsuart0 = &uart6;
};
vph_pwr: vph-pwr-regulator {
compatible = "regulator-fixed";
regulator-name = "vph_pwr";
regulator-min-microvolt = <3700000>;
regulator-max-microvolt = <3700000>;
};
/*
* Apparently RPMh does not provide support for PM8998 S4 because it
* is always-on; model it as a fixed regulator.
*/
vreg_s4a_1p8: pm8998-smps4 {
compatible = "regulator-fixed";
regulator-name = "vreg_s4a_1p8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
vin-supply = <&vph_pwr>;
};
i2c_touch: i2c {
compatible = "i2c-gpio";
status = "okay";
sda-gpios = <&tlmm 49 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
scl-gpios = <&tlmm 50 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <5>; /* 5~=100 kHz */
#address-cells = <1>;
#size-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c_ts_pins>;
touchscreen: synaptics-rmi4-i2c@20 {
compatible = "syna,rmi4-i2c";
reg = <0x20>;
#address-cells = <1>;
#size-cells = <0>;
interrupts-extended = <&tlmm 125 0x2008>; // IRQF_ONESHOT | IRQF_TRIGGER_LOW
pinctrl-names = "default";
pinctrl-0 = <&ts_default_pins &ts_enable_1p8>;
vdd-supply = <&vreg_l28a_3p0>;
vio-supply = <&vreg_l6a_1p8>;
syna,reset-delay-ms = <200>;
syna,startup-delay-ms = <500>;
rmi4-f01@1 {
reg = <0x01>;
syna,nosleep-mode = <1>;
};
rmi4_f12: rmi4-f12@12 {
reg = <0x12>;
touchscreen-x-mm = <68>;
touchscreen-y-mm = <144>;
syna,sensor-type = <1>;
syna,rezero-wait-ms = <200>;
};
};
};
gpio_tristate_key: gpio-keys {
compatible = "gpio-keys";
label = "Tri-state key";
pinctrl-names = "default";
pinctrl-0 = <&tri_state_key_default>;
state-top {
label = "Tri-state key top";
linux,code = <KEY_A>;
// gpios = <&tlmm 40 GPIO_ACTIVE_LOW>;
interrupt-parent = <&tlmm>;
interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
debounce-interval = <500>;
linux,can-disable;
};
state-middle {
label = "Tri-state key middle";
linux,code = <KEY_B>;
// gpios = <&tlmm 42 GPIO_ACTIVE_LOW>;
interrupt-parent = <&tlmm>;
interrupts = <52 IRQ_TYPE_EDGE_FALLING>;
debounce-interval = <500>;
linux,can-disable;
};
state-bottom {
label = "Tri-state key bottom";
linux,code = <KEY_C>;
// gpios = <&tlmm 26 GPIO_ACTIVE_LOW>;
interrupt-parent = <&tlmm>;
interrupts = <126 IRQ_TYPE_EDGE_FALLING>;
debounce-interval = <500>;
linux,can-disable;
};
};
gpio_vol_keys: gpio-keys {
compatible = "gpio-keys";
label = "Volume keys";
autorepeat;
pinctrl-names = "default";
pinctrl-0 = <&volume_down_gpio &volume_up_gpio>;
vol-down {
label = "Volume down";
linux,code = <KEY_VOLUMEDOWN>;
gpios = <&pm8998_gpio 5 GPIO_ACTIVE_LOW>;
debounce-interval = <15>;
};
vol-up {
label = "Volume up";
linux,code = <KEY_VOLUMEUP>;
gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
debounce-interval = <15>;
};
};
extcon_usb1: extcon-usb-1 {
compatible = "linux,extcon-usb-gpio";
id-gpio = <&tlmm 38 GPIO_ACTIVE_HIGH>;
};
};
&apps_rsc {
pm8998-rpmh-regulators {
compatible = "qcom,pm8998-rpmh-regulators";
qcom,pmic-id = "a";
vdd-s1-supply = <&vph_pwr>;
vdd-s2-supply = <&vph_pwr>;
vdd-s3-supply = <&vph_pwr>;
vdd-s4-supply = <&vph_pwr>;
vdd-s5-supply = <&vph_pwr>;
vdd-s6-supply = <&vph_pwr>;
vdd-s7-supply = <&vph_pwr>;
vdd-s8-supply = <&vph_pwr>;
vdd-s9-supply = <&vph_pwr>;
vdd-s10-supply = <&vph_pwr>;
vdd-s11-supply = <&vph_pwr>;
vdd-s12-supply = <&vph_pwr>;
vdd-s13-supply = <&vph_pwr>;
vdd-l1-l27-supply = <&vreg_s7a_1p025>;
vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>;
vdd-l3-l11-supply = <&vreg_s7a_1p025>;
vdd-l4-l5-supply = <&vreg_s7a_1p025>;
vdd-l6-supply = <&vph_pwr>;
vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>;
vdd-l9-supply = <&vreg_bob>;
vdd-l10-l23-l25-supply = <&vreg_bob>;
vdd-l13-l19-l21-supply = <&vreg_bob>;
vdd-l16-l28-supply = <&vreg_bob>;
vdd-l18-l22-supply = <&vreg_bob>;
vdd-l20-l24-supply = <&vreg_bob>;
vdd-l26-supply = <&vreg_s3a_1p35>;
vin-lvs-1-2-supply = <&vreg_s4a_1p8>;
vreg_s2a_1p125: smps2 {
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
};
vreg_s3a_1p35: smps3 {
regulator-min-microvolt = <1352000>;
regulator-max-microvolt = <1352000>;
};
vreg_s5a_2p04: smps5 {
regulator-min-microvolt = <1904000>;
regulator-max-microvolt = <2040000>;
};
vreg_s7a_1p025: smps7 {
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <1028000>;
};
vdd_qusb_hs0:
vdda_hp_pcie_core:
vdda_mipi_csi0_0p9:
vdda_mipi_csi1_0p9:
vdda_mipi_csi2_0p9:
vdda_mipi_dsi0_pll:
vdda_mipi_dsi1_pll:
vdda_qlink_lv:
vdda_qlink_lv_ck:
vdda_qrefs_0p875:
vdda_pcie_core:
vdda_pll_cc_ebi01:
vdda_pll_cc_ebi23:
vdda_sp_sensor:
vdda_ufs1_core:
vdda_ufs2_core:
vdda_usb1_ss_core:
vdda_usb2_ss_core:
vreg_l1a_0p875: ldo1 {
regulator-min-microvolt = <880000>;
regulator-max-microvolt = <880000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vddpx_10:
vreg_l2a_1p2: ldo2 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
regulator-always-on;
};
vreg_l3a_1p0: ldo3 {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vdd_wcss_cx:
vdd_wcss_mx:
vdda_wcss_pll:
vreg_l5a_0p8: ldo5 {
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vddpx_13:
vreg_l6a_1p8: ldo6 {
regulator-min-microvolt = <1856000>;
regulator-max-microvolt = <1856000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l7a_1p8: ldo7 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l8a_1p2: ldo8 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1248000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l9a_1p8: ldo9 {
regulator-min-microvolt = <1704000>;
regulator-max-microvolt = <2928000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l10a_1p8: ldo10 {
regulator-min-microvolt = <1704000>;
regulator-max-microvolt = <2928000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l11a_1p0: ldo11 {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1048000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vdd_qfprom:
vdd_qfprom_sp:
vdda_apc1_cs_1p8:
vdda_gfx_cs_1p8:
vdda_qrefs_1p8:
vdda_qusb_hs0_1p8:
vddpx_11:
vreg_l12a_1p8: ldo12 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vddpx_2:
vreg_l13a_2p95: ldo13 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2960000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l14a_1p88: ldo14 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
regulator-always-on;
};
vreg_l15a_1p8: ldo15 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l16a_2p7: ldo16 {
regulator-min-microvolt = <2704000>;
regulator-max-microvolt = <2704000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l17a_1p3: ldo17 {
regulator-min-microvolt = <1304000>;
regulator-max-microvolt = <1304000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l18a_2p7: ldo18 {
regulator-min-microvolt = <2704000>;
regulator-max-microvolt = <2960000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l19a_3p0: ldo19 {
regulator-min-microvolt = <2856000>;
regulator-max-microvolt = <3104000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l20a_2p95: ldo20 {
regulator-min-microvolt = <2704000>;
regulator-max-microvolt = <2960000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l21a_2p95: ldo21 {
regulator-min-microvolt = <2704000>;
regulator-max-microvolt = <2960000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l22a_2p85: ldo22 {
regulator-min-microvolt = <2864000>;
regulator-max-microvolt = <3312000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l23a_3p3: ldo23 {
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3312000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vdda_qusb_hs0_3p1:
vreg_l24a_3p075: ldo24 {
regulator-min-microvolt = <3088000>;
regulator-max-microvolt = <3088000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l25a_3p3: ldo25 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3312000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vdda_hp_pcie_1p2:
vdda_hv_ebi0:
vdda_hv_ebi1:
vdda_hv_ebi2:
vdda_hv_ebi3:
vdda_mipi_csi_1p25:
vdda_mipi_dsi0_1p2:
vdda_mipi_dsi1_1p2:
vdda_pcie_1p2:
vdda_ufs1_1p2:
vdda_ufs2_1p2:
vdda_usb1_ss_1p2:
vdda_usb2_ss_1p2:
vreg_l26a_1p2: ldo26 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l28a_3p0: ldo28 {
regulator-min-microvolt = <2856000>;
regulator-max-microvolt = <3008000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_lvs1a_1p8: lvs1 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
vreg_lvs2a_1p8: lvs2 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
};
pmi8998-rpmh-regulators {
compatible = "qcom,pmi8998-rpmh-regulators";
qcom,pmic-id = "b";
vdd-bob-supply = <&vph_pwr>;
vreg_bob: bob {
regulator-min-microvolt = <3312000>;
regulator-max-microvolt = <3600000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
regulator-allow-bypass;
};
};
pm8005-rpmh-regulators {
compatible = "qcom,pm8005-rpmh-regulators";
qcom,pmic-id = "c";
vdd-s1-supply = <&vph_pwr>;
vdd-s2-supply = <&vph_pwr>;
vdd-s3-supply = <&vph_pwr>;
vdd-s4-supply = <&vph_pwr>;
vreg_s3c_0p6: smps3 {
regulator-min-microvolt = <600000>;
regulator-max-microvolt = <600000>;
};
};
};
/* Reserved memory changes */
/*
* The rmtfs memory region in downstream is 'dynamically allocated'
* but given the same address every time. hard code it here as this address is
* where the modem firmware expects it to be.
*/
/delete-node/ &rmtfs_mem;
/ {
reserved-memory {
rmtfs_mem: memory@f5b01000 {
compatible = "qcom,rmtfs-mem";
reg = <0 0xf5b01000 0 0x200000>;
no-map;
qcom,client-id = <1>;
qcom,vmid = <15>;
};
/*
* Due to treble implementations and the requirement to reflash
* the dtbo partition in order to boot downstream without doing a
* cold reboot, this region has not proven very useful on enchilada.
*/
ramoops: ramoops@0xac300000 {
compatible = "ramoops";
reg = <0 0xac300000 0 0x400000>;
record-size = <0x40000>;
console-size = <0x40000>;
ftrace-size = <0x40000>;
pmsg-size = <0x200000>;
devinfo-size = <0x1000>;
ecc-size = <0x0>;
};
};
};
&gcc {
protected-clocks = <GCC_QSPI_CORE_CLK>,
<GCC_QSPI_CORE_CLK_SRC>,
<GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
<GCC_LPASS_Q6_AXI_CLK>,
<GCC_LPASS_SWAY_CLK>;
};
&gpu {
zap-shader {
memory-region = <&gpu_mem>;
firmware-name = "qcom/sdm845/oneplus6/a630_zap.mbn";
};
};
&adsp_pas {
status = "okay";
firmware-name = "qcom/sdm845/adsp.mbn";
};
&cdsp_pas {
status = "okay";
firmware-name = "qcom/sdm845/cdsp.mbn";
};
/* Modem/wifi*/
&mss_pil {
status = "okay";
firmware-name = "qcom/sdm845/oneplus6/mba.mbn", "qcom/sdm845/oneplus6/modem.mbn";
};
&uart6 {
status = "okay";
bluetooth {
compatible = "qcom,wcn3990-bt";
/* In subdir qca/ in /lib/firmware */
//firmware-name = "crbtfw21.tlv";
vddio-supply = <&vreg_s4a_1p8>;
vddxo-supply = <&vreg_l7a_1p8>;
vddrf-supply = <&vreg_l17a_1p3>;
vddch0-supply = <&vreg_l25a_3p3>;
max-speed = <3200000>;
};
};
&qup_uart6_default {
pinmux {
pins = "gpio45", "gpio46", "gpio47", "gpio48";
function = "qup6";
};
cts {
pins = "gpio45";
bias-pull-down;
};
rts-tx {
pins = "gpio46", "gpio47";
drive-strength = <2>;
bias-disable;
};
rx {
pins = "gpio48";
bias-pull-up;
};
};
&ufs_mem_hc {
status = "okay";
reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
vcc-supply = <&vreg_l20a_2p95>;
vcc-max-microamp = <600000>;
};
&ufs_mem_phy {
status = "okay";
vdda-phy-supply = <&vdda_ufs1_core>;
vdda-pll-supply = <&vdda_ufs1_1p2>;
};
&usb_1 {
status = "okay";
/* disable USB3 clock requirement as we are in USB 2 mode */
qcom,select-utmi-as-pipe-clk;
};
&usb_1_dwc3 {
/*
* Can't detect USB cable being plugged / unplugged, so this is needed
* for gadget mode
*/
dr_mode = "peripheral";
/* fastest mode for USB 2 */
maximum-speed = "high-speed";
extcon = <&extcon_usb1>;
/* Remove USB3 phy */
phys = <&usb_1_hsphy>;
phy-names = "usb2-phy";
};
&usb_1_hsphy {
status = "okay";
vdd-supply = <&vdda_usb1_ss_core>;
vdda-pll-supply = <&vdda_qusb_hs0_1p8>;
vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>;
qcom,imp-res-offset-value = <8>;
qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
};
&wifi {
status = "okay";
vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
};
&mdss {
status = "okay";
};
&mdss_mdp {
status = "okay";
};
&dsi0 {
status = "okay";
vdda-supply = <&vdda_mipi_dsi0_1p2>;
#address-cells = <1>;
#size-cells = <0>;
display_panel: panel@0 {
status = "disabled";
port {
panel_in: endpoint {
remote-endpoint = <&dsi0_out>;
};
};
};
};
&dsi0_out {
remote-endpoint = <&panel_in>;
data-lanes = <0 1 2 3>;
};
&dsi0_phy {
status = "okay";
vdds-supply = <&vdda_mipi_dsi0_pll>;
};
/* GENI device - does i2c, uart, spi and all that stuff */
&qupv3_id_1 {
status = "okay";
};
&qupv3_id_0 {
status = "okay";
};
&spmi_bus {
pmi8998_lsid1: pmic@3 {
lpg {
status = "okay";
rgb {
led-sources = <5 4 3>;
};
red {
led-sources = <5>;
};
green {
led-sources = <4>;
};
blue {
led-sources = <3>;
};
};
};
};
&i2c10 {
status = "okay";
clock-frequency = <100000>;
bq27541_battery: bq27541-battery@55 {
status = "okay";
compatible = "ti,bq27541";
reg = <0x55>;
};
};
/* PINCTRL - additions to nodes defined in sdm845.dtsi */
&qup_i2c10_default {
pinconf {
pins = "gpio55", "gpio56";
drive-strength = <2>;
bias-disable;
};
};
&qup_uart9_default {
pinconf-tx {
pins = "gpio4";
drive-strength = <2>;
bias-disable;
};
pinconf-rx {
pins = "gpio5";
drive-strength = <2>;
bias-pull-up;
};
};
&pm8998_gpio {
volume_down_gpio: pm8998_gpio5 {
pinconf {
pins = "gpio5";
function = "normal";
input-enable;
bias-pull-up;
qcom,drive-strength = <0>;
};
};
volume_up_gpio: pm8998_gpio6 {
pinconf {
pins = "gpio6";
function = "normal";
input-enable;
bias-pull-up;
qcom,drive-strength = <0>;
};
};
};
&tlmm {
gpio-reserved-ranges = <0 4>, <81 4>;
sdc2_clk: sdc2-clk {
pinconf {
pins = "sdc2_clk";
bias-disable;
/*
* It seems that mmc_test reports errors if drive
* strength is not 16 on clk, cmd, and data pins.
*/
drive-strength = <16>;
};
};
sdc2_cmd: sdc2-cmd {
pinconf {
pins = "sdc2_cmd";
bias-pull-up;
drive-strength = <16>;
};
};
sdc2_data: sdc2-data {
pinconf {
pins = "sdc2_data";
bias-pull-up;
drive-strength = <16>;
};
};
tri_state_key_default: tri_state_key_default {
mux {
pins = "gpio40", "gpio42", "gpio26";
function = "gpio";
};
config {
pins = "gpio40", "gpio42", "gpio26";
drive-strength = <2>;
bias-disable;
};
};
i2c_ts_pins: i2c-touch-default {
mux {
pins = "gpio49", "gpio50";
function = "gpio";
};
config {
pins = "gpio49", "gpio50";
drive-strength = <2>;
bias-disable;
};
};
ts_default_pins: ts-int {
mux {
pins = "gpio99", "gpio125";
function = "gpio";
};
config {
pins = "gpio99", "gpio125";
drive-strength = <16>;
bias-pull-up;
};
};
ts_enable_1p8: ts-1p8 {
mux {
pins = "gpio88";
function = "gpio";
};
config {
pins = "gpio88";
drive-strength = <16>;
bias-pull-up;
};
};
panel_reset_pins: panel-reset {
mux {
pins = "gpio6", "gpio25", "gpio26";
function = "gpio";
};
config {
pins = "gpio6", "gpio25", "gpio26";
drive-strength = <8>;
bias-disable = <0>;
};
};
panel_te_pin: panel-te {
mux {
pins = "gpio10";
function = "mdp_vsync";
};
config {
pins = "gpio10";
drive-strength = <2>;
bias-disable;
input-enable;
};
};
panel_esd_pin: panel-esd {
mux {
pins = "gpio30";
function = "gpio";
};
config {
pins = "gpio30";
drive-strength = <2>;
bias-pull-down;
input-enable;
};
};
};
View Git Blame Copy Permalink